Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA ELECTRODE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Microparticles deep in the plasma sheath: Coulomb 'explosion'

A cloud of microparticles was trapped deep in the sheath of a radio-frequency (rf) discharge, very close to the lower (grounded) electrode of the plasma chamber. This was achieved by employing a specifically designed rf-driven segment integrated in the lower electrode, which provided an additional confinement compressing the cloud to a very high density. After switching the rf-driven segment off, the cloud 'exploded' due to mutual interparticle repulsion. By combining a simple theoretical model with different numerical simulation methods, some basic properties of complex plasmas in this highly non-equilibrium regime were determined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Contrasting the characteristics of atmospheric pressure plasma jets operated with single and double dielectric material: physicochemical characteristics and application to bacterial killing

Abstract This study reports an experimental comparison of two types of atmospheric pressure plasma jets in terms of their fundamental plasma characteristics and efficacy in bacterial sterilization. The plasma jets are fabricated by inserting a high voltage electrode inside a one-end closed (double DBD plasma jet) or both ends open (single DBD plasma jet) quartz tubes which are further enclosed inside a second quartz tube containing a ground electrode. Both plasma jets are operated in contact with water surface by using a unipolar pulsed DC power supply with helium as the working gas. Results from electrical and time-resolved imaging show that the single DBD configuration induces 3–4 times higher accumulation of charges onto the water surface with significantly faster propagation of plasma bullets. These results are accompanied by the higher discharge intensity as well as stronger emissions from short-lived reactive species which were analyzed through optical emission spectroscopy at the plasma-water interface. The rotational temperature for the single DBD configuration was observed to be higher making it unsafe for direct treatments of sensitive biological targets. These characteristics of the single DBD configuration result in the production of more than two times higher concentration of H 2 O 2 in plasma activated water. Shielding of the HV electrode reduces the plasma potential which in turn reduces the electric field & electron energy at the plasma-water interface. The reduced electric field for the double DBD configuration was lower by ≈463 Td than the single DBD configuration. The bactericidal efficacy of the two configurations of the plasma jets were tested against Escherichia coli , a well studied Gram-negative bacterium that can be commensal and pathogenic in human body. Our results demonstrate that although single DBD plasma jet result in stronger antibacterial effects, the double DBD configuration could be safer.

Physics↗
DOE OSTI2017

Kinetics of charged particles in a high-voltage gas discharge in a nonuniform electrostatic field

A high-voltage gas discharge is of interest as a possible means of generating directed flows of low-temperature plasma in the off-electrode space distinguished by its original features [1–4]. We propose a model for calculating the trajectories of charges particles in a high-voltage gas discharge in nitrogen at a pressure of 0.15 Torr existing in a nonuniform electrostatic field and the strength of this field. Based on the results of our calculations, we supplement and refine the extensive experimental data concerning the investigation of such a discharge published in [1, 2, 5–8]; good agreement between the theory and experiment has been achieved. The discharge burning is initiated and maintained through bulk electron-impact ionization and ion–electron emission. We have determined the sizes of the cathode surface regions responsible for these processes, including the sizes of the axial zone involved in the discharge generation. The main effect determining the kinetics of charged particles consists in a sharp decrease in the strength of the field under consideration outside the interelectrode space, which allows a free motion of charges with specific energies and trajectories to be generated in it. The simulation results confirm that complex electrode systems that allow directed plasma flows to be generated at a discharge current of hundreds or thousands of milliamperes and a voltage on the electrodes of 0.3–1 kV can be implemented in practice [3, 9, 10].

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Apparatus for atmospheric pressure pin-to-hole spark discharge and uses thereof

Disclosed herein are atmospheric pressure pin-to-hole pulsed spark discharge devices and methods for creating plasma. The devices include a conduit for fluidically communicating a gas, a plasma, or both, therethrough, portion of the conduit capable of being connected to a gas supply, and a second portion of the conduit capable of emitting a plasma; a positive electrode comprising a sharp tip; and a ground plate electrode. Disclosed are methods for treating a skin ulcer using non-thermal plasma include flowing a gas through a cold spark discharge zone simultaneously with the creation of a pulsed spark discharge to give rise to a non-thermal plasma emitted from a conduit, the non-thermal plasma comprising NO; and contacting a skin ulcer with said non-thermal plasma for sufficient time and intensity to give rise to treatment of the skin ulcer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Apparatus for atmospheric pressure pin-to-hole spark discharge and uses thereof

Disclosed herein are atmospheric pressure pin-to-hole pulsed spark discharge devices and methods for creating plasma. The devices include a conduit for fluidically communicating a gas, a plasma, or both, therethrough, portion of the conduit capable of being connected to a gas supply, and a second portion of the conduit capable of emitting a plasma; a positive electrode comprising a sharp tip; and a ground plate electrode. Disclosed are methods for treating a skin ulcer using non-thermal plasma include flowing a gas through a cold spark discharge zone simultaneously with the creation of a pulsed spark discharge to give rise to a non-thermal plasma emitted from a conduit, the non-thermal plasma comprising NO; and contacting a skin ulcer with said non-thermal plasma for sufficient time and intensity to give rise to treatment of the skin ulcer.

Dobrynin, Danil V.↗
DOE OSTI2013

Pure ion current collection in ion sensitive probe measurement with a metal mesh guard electrode for evaluation of ion temperature in magnetized plasma

This paper presents a new design of ion sensitive probe (ISP) that enables collection of pure ion current for accurate measurement of the perpendicular ion temperature in magnetized plasmas. The new type of ISP resolves a longstanding issue widely observed in ISP type measurements, namely, that the current-voltage characteristic is smeared by an unexpected electron current in the standard ISP model. The new ISP is equipped with a fine scale metal mesh on the sensor entrance to prevent electrons from flowing to the sensor, a phenomenon considered to be caused by the space-charge effect. The new ISP successfully measured the ion temperature of electron cyclotron resonance plasmas.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

End loss analyzer system for measurements of plasma flux at the C-2U divertor electrode

An end loss analyzer system consisting of electrostatic, gridded retarding-potential analyzers and pyroelectric crystal bolometers was developed to characterize the plasma loss along open field lines to the divertors of C-2U. The system measures the current and energy distribution of escaping ions as well as the total power flux to enable calculation of the energy lost per escaping electron/ion pair. Special care was taken in the construction of the analyzer elements so that they can be directly mounted to the divertor electrode. An attenuation plate at the entrance to the gridded retarding-potential analyzer reduces plasma density by a factor of 60 to prevent space charge limitations inside the device, without sacrificing its angular acceptance of ions. In addition, all of the electronics for the measurement are isolated from ground so that they can float to the bias potential of the electrode, 2 kV below ground.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2014

Plasma characteristics of single- and dual-electrode ion source systems utilized in low-energy ion extraction

Discharge characteristics in the upstream as well as in the downstream regions of a 50-eV positive ion beam were measured along the beam axis. Single- and dual-electrode configurations made of 0.1-mm diameter tungsten wires were tested. By varying the upstream discharge parameters, the shape of the sheath edge around the extractors, which can either be “planar” or “cylindrical,” can be controlled. The sheath eventually affected the simultaneous extraction of ions and neutralizing electrons. The dual-electrode configuration at the lower discharge current, revealed a homogeneous discharge downstream. At this condition, the edge of the sheath can be inferred to be “planar” which allowed the uniform extraction and propagation of low-energy ions at longer distances. The dual-electrode configuration was capable of transmitting low-energy ions up to 70 mm downstream.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2012

Brightness enhancement of plasma ion source by utilizing anode spot for nano applications

Anode spots are known as additional discharges on positively biased electrode immersed in plasmas. The anode spot plasma ion source (ASPIS) has been investigated as a high brightness ion source for nano applications such as focused ion beam (FIB) and nano medium energy ion scattering (nano-MEIS). The generation of anode spot is found to enhance brightness of ion beam since the anode spot increases plasma density near the extraction aperture. Brightness of the ASPIS has been estimated from measurement of emittance for total ion beam extracted through sub-mm aperture. The ASPIS is installed to the FIB system. Currents and diameters of the focused beams with/without anode spot are measured and compared. As the anode spot is turned on, the enhancement of beam current is observed at fixed diameter of the focused ion beam. Consequently, the brightness of the focused ion beam is enhanced as well. For argon ion beam, the maximum normalized brightness of 12 300 A/m{sup 2} SrV is acquired. The ASPIS is applied to nano-MEIS as well. The ASPIS is found to increase the beam current density and the power efficiency of the ion source for nano-MEIS. From the present study, it is shown that the ASPIS can enhance the performance of devices for nano applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Low-Temperature Plasma-Based Metrology of Lithium-Ion Battery Electrode Materials (CRADA Final Report)

As part of the Cyclotron Road program, SirenOpt Inc. evaluated its low-temperature plasma-based metrology sensor prototype for measuring multiple critical properties of lithium-ion battery electrode materials in parallel and in real-time. Cost-effective, minimal-waste manufacturing of high-performance battery electrode materials will be vital for achieving society’s net-zero carbon emission goals. Because existing electrode metrology sensors cannot operate within most sections of manufacturing lines, manufacturers often complete hundreds of processing steps before they can test their products and detect problems. When manufacturers perform these offline tests, they typically only test a small portion of the manufactured products. Current electrode manufacturing thus often yields many low-quality products, or off-spec products that must be thrown away all together. For example, at least 6% of the total lithium-ion battery manufacturing cost (i.e., over $250 million/year for the average gigafactory) is devoted to processing defective electrodes that are not scrapped until performance tests are failed during late-stage quality control checks. Electrode variability also leads manufacturers to build extra cells into battery packs to reduce the risk of poor performance. For example, many electric vehicle (EV) manufacturers include up to 10% more cells than needed, which substantially increases the cost and weight of the final EV product. The SirenOpt sensor can potentially enable early detection of poorly manufactured electrodes and allow them to be removed earlier from manufacturing lines, which can save battery manufacturers (hundreds of) millions of dollars per year. The sensor can further be used to improve product quality by accelerating R&D and process optimization, improving quality control, and enabling real-time process control. Overall, a real-time, in-situ metrology strategy can create unprecedented opportunities for implementation of smart manufacturing practices and advanced quality and process control solutions to realize higher battery electrode throughput and performance.

25 ENERGY STORAGE↗
NASA NTRS1992

Scaling of 100 kW class applied-field MPD thrusters

Three cylindrical applied-field magnetoplasmadynamic thrusters were tested with argon propellant over a broad range of operating conditions to establish empirical scaling laws for thruster performance. Argon flow rates, discharge currents, and applied-field strengths were varied between 0.025 and 0.14 g/s, 750 to 2000 A, and 0.034 to 0.20T, respectively. The results showed that the thrust reached over five times the self-field value, and that thrust increased linearly with the product of discharge current and applied-field strength and quadratically with the anode radius. While increasing the propellant flow rate increased the thrust, it did not affect the rate of thrust increase with applied-field strength, and at low propellant flow rates the self-field thrust approached 30 percent of the measured thrust. The voltage increased linearly with applied-field strength but was insensitive to the discharge current. The rate of voltage increase with applied-field strength dependent on anode radius. Thruster efficiency increased monotonically with applied-field strength and propellant flow rate. Peak thruster efficiencies were insensitive to changes in anode radius. Electrode power loss and thruster efficiency measurements showed that while the electrode losses decreased with increasing anode radius the plasma losses increased. The opposite behaviors of electrode and plasma losses demonstrates the need to identify ways of independently controlling the thruster loss mechanisms.

Myers, Roger M.↗
NASA NTRS2018

Development of the Electrostatic Precipitator (ESP) for Mars and Electrodynamic Dust Shield (EDS)

Kennedy Space Center's Swamp Works is a fast-paced and diverse technology development laboratory that aims to advance commercial and government capabilities to colonize extraterrestrial environments. As a part of Swamp Works, the Electrostatic and Surface Physics Laboratory (ESPL) is currently developing new technologies that will further NASA's capabilities to colonize lunar and Martian environments. At the ESPL, the objective of the overall project is to aid in the dust mitigation of robotic and human exploration missions to the moon and Mars. The moon and Mars are covered with layers of dust, which can make long-term exploration missions very difficult. The team at the ESPL is developing an electrostatic precipitator (ESP) to aid in the reduction of interference from airborne Martian dust on equipment. The ESP is designed to mitigate the dust in an intake of CO2-rich dusty gas (i.e., the Martian atmosphere). The ESP is essentially a cylindrical tube with a coaxial wire electrode. Applying a high voltage through this electrode induces a corona discharge (a glowing plasma that envelops the electrode), which is used to charge the inflowing dust. The electric field caused by the corona pushes the charged dust to the walls of the precipitator, preventing the dust to flow out of the tube. Environmental dust can make long-term exploration missions very difficult, and settled dust is no exception. Settled lunar or Martian dust can hinder the performance and lifetime of equipment. For example, dust can settle on the solar panels of a lunar or Martian rover, decreasing its performance while increasing its charging time. To address this, the team at the ESPL is also developing an electrodynamic dust shield (EDS), which is designed to remove lunar or Martian dust from the surfaces of equipment. The EDS uses a non-uniform electric field to generate a dielectrophoretic force, which pushes the particles away from the surface of the shield. A number of dust shields will be tested on the exterior of the International Space Station (ISS) via MISSE-11, a flight payload to the ISS that will test the effects of long-term exposure to space on materials. During my internship at the ESPL, I aided in the development of these technologies. For the ESP, I helped characterize the electrical properties of various geometries and helped redesign the hardware of the testbed (the precipitator used to test this technology in the lab). To characterize the electrical properties of the ESP, I ran various tests of the precipitator, which consisted of varying the environmental conditions and geometry of the testbed. Analyzing the electrical properties of the ESP in various environmental conditions is necessary to characterize its collection efficiency, since it will be used in the dusty Martian environment. For the EDS, I helped analyze the dielectric strength of the surface of the shield via high-voltage testing. A dielectrically strong surface will help the shield survive the harsh environment of space, which will enable it to have both lunar and Martian applications.

Corona Discharge↗
NASA NTRS1990

Laboratory experiments on current flow between stationary and moving electrodes in magnetoplasmas

Laboratory experiments were performed in order to investigate the basic physics of current flow between tethered electrodes in magnetoplasmas. The major findings are summarized. The experiments are performed in an effectively very large laboratory plasma in which not only the nonlinear current collection is addressed but also the propagation and spread of currents, the formation of current wings by moving electrodes, the current closure, and radiation from transmission lines. The laboratory plasma consists of a pulsed dc discharge whose Maxwellian afterglow provides a quiescent, current-free uniform background plasma. Electrodes consisting of collectors and electron emitters are inserted into the plasma and a pulsed voltage is applied between two floating electrodes via insulated transmission lines. Besides the applied current in the wire, the total current density in the plasma is obtained from space and time resolved magnetic probe measurements via Maxwell's law. Langmuir probes yield the plasma parameters.

Stenzel, Reiner L.↗
DOE OSTI2011

Theoretical investigation of phase-controlled bias effect in capacitively coupled plasma discharges

We theoretically investigated the effect of phase difference between powered electrodes in capacitively coupled plasma (CCP) discharges. Previous experimental result has shown that the plasma potential could be controlled by using a phase-shift controller in CCP discharges. In this work, based on the previously developed radio frequency sheath models, we developed a circuit model to self-consistently determine the bias voltage from the plasma parameters. Results show that the present theoretical model explains the experimental results quite well and there is an optimum value of the phase difference for which the V{sub dc}/V{sub pp} ratio becomes a minimum.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗