Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA SWITCHES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

SOHO/CDS Measurements of Coronal EUV Polarization above the Limb

Attempts to measure polarization in coronal EUV emission above the solar limb have been made using the SOHO/CDS normal-incidence spectrometer which has a polarization sensitivity of about 50%, a property that causes variations in intensity response as a function of the spacecraft's roll angle for polarized light. Such observations were made on the disk and up to 0.22 solar radii above the solar limb in a number of EUV lines during two special roll-maneuvers of the SOHO spacecraft. Measurements of intensity gradients were made above a modestly active equatorial region in 1997 and above a relatively cool polar region in 2001. Observed emission lines include He I 584A, He II 304A, 0 IV 555+610A, 0 V 630A, Mg IX 368A, Mg X 610+625A, and Si XI 303A, formed at temperatures that evenly cover the range in logT from 4.1 to 6.2. Near the disk, measured intensities of all lines fall off exponentially at different rates that can be used to determine the density scale-heights of the emitting plasma, since this emission is dominated by collisional excitation with an Ne-squared dependence. Assuming hydrostatic equilibrium, the intensity gradient for each line can then be converted into a 'scale-height temperature', which is found to be closely related to the ionization temperature of each line over the wide range of lines and solar conditions observed. Beyond a certain distance, intensity gradients of the cooler lines switch over to a flatter exponential slope, suggesting that this radiation is dominated by resonance scattering which varies as Ne to the first power. Such radiation should also be linearly polarized in the plane containing the line-of-sight and the solar center, a signature that would strongly confirm this interpretation.

Thomas, Roger J.↗

Fast modulating electron cyclotron emission (FMECE) diagnostic for tokamaks

Utilizing variable-frequency channels, e.g., yttrium iron garnet (YIG) bandpass filters, in the intermediate frequency (IF) section of an electron cyclotron emission (ECE) radiometer facilitates flexibility in the volume viewed by the ECE channels as well as high resolution electron temperature and temperature fluctuation measurements in tokamaks. Fast modulating electron cyclotron emission (FMECE), a stand-alone IF section with eight channels, is a novel application of YIG filters for real-time electron temperature gradient and gradient scale length measurements. Key to FMECE is a simultaneous input/output data acquisition unit, as well as a modified type of YIG filters, which is capable of fast switching of their center (set) frequencies with a frequency slew rate of 600 μs/GHz. A new FMECE has been implemented and tested on the DIII-D tokamak, demonstrating its capability in real-time gradient measurements. Here, the data presented here shows that FMECE can identify flattening in the electron temperature profile; the latter can be used as a sensor for real time monitoring and control of plasma instabilities. Implementation and application are planned for the EAST tokamak.

47 OTHER INSTRUMENTATION↗

'Self-consistent' production of ion conics on return current region auroral field lines - A time-dependent, semi-kinetic model

We describe initial results from a time-dependent, semi-kinetic model of plasma outflow incorporating wave-particle interactions along current-carrying auroral field lines. Electrostatic waves are generated by the current driven ion cyclotron instability (CDICI), causing perpendicular velocity diffusion of ions plus electron heating via anomalous resistivity when and where the relative drift between electrons and ions exceeds certain critical velocities. Using the local bulk parameters we calculate these critical velocities, and so are able to self-consistently switch on and off the heating of the various particle species. Due to the dependence of these critical velocities on the bulk parameters of the species the heating effects exhibit quite complex spatial and temporal variations. A wide range of ion distribution functions are observed in these simulations, including conics with energies of a few electron volts and 'ring' distributions. The rings are seen to be a natural result of transverse heating and velocity filter effects and do not require coherent acceleration processes. We also observe the formation of a density depletion in hydrogen and enhanced oxygen densities at high altitudes.

Brown, David G.↗

3D MHD MODELING OF TWISTED CORONAL LOOPS

We perform MHD modeling of a single bright coronal loop to include the interaction with a non-uniform magnetic field. The field is stressed by random footpoint rotation in the central region and its energy is dissipated into heating by growing currents through anomalous magnetic diffusivity that switches on in the corona above a current density threshold. We model an entire single magnetic flux tube in the solar atmosphere extending from the high- β chromosphere to the low- β corona through the steep transition region. The magnetic field expands from the chromosphere to the corona. The maximum resolution is ∼30 km. We obtain an overall evolution typical of loop models and realistic loop emission in the EUV and X-ray bands. The plasma confined in the flux tube is heated to active region temperatures (∼3 MK) after ∼2/3 hr. Upflows from the chromosphere up to ∼100 km s{sup −1} fill the core of the flux tube to densities above 10{sup 9} cm{sup −3}. More heating is released in the low corona than the high corona and is finely structured both in space and time.

79 ASTRONOMY AND ASTROPHYSICS↗

Fiber Optic Switch For Broadband Emission Spectroscopy

Many high-temperature processes comprise large-scale phenomena. Studying spatial and temporal correlations of physical processes between several locations within characteristic scales provides desired information on macroscopic physical processes. Achieved with emission spectroscopy by use of multiple optical fibers. Simultaneous coupling of light from these fibers into single available spectrometer and/or monochromator not accomplished without added expense of two-dimensional array and increased complexity of calibration. Quasi-simultaneous coupling, while maintaining optimum alignment and maximum throughput of broadband emission, achieved by use of fiber optic multiscanner. Instrument used successfully in study of frozen-flow losses internal to flow of plasma inside nozzle of arc jet. Instrument includes two hollow disks of different sizes and stepping motor.

De Groot, Wim↗

Efficient and compact thermo-optic phase shifter in silicon-rich silicon nitride

The design, fabrication, and characterization of low-loss ultra-compact bends in high-index (${n} = {3.1}$ at $\lambda = {1550}\;{\rm nm}$) plasma-enhanced chemical vapor deposition silicon-rich silicon nitride (SRN) were demonstrated and utilized to realize efficient, small footprint thermo-optic phase shifter. Compact bends were structured into a folded waveguide geometry to form a rectangular spiral within an area of ${65} \times {65}\;\unicode{x00B5}{{\rm m}^2}$, having a total active waveguide length of 1.2 mm. The device featured a phase-shifting efficiency of $8\;{\rm mW}/\pi$ and a 3 dB switching bandwidth of 15 KHz. Here, we propose SRN as a promising thermo-optic platform that combines the properties of silicon and stoichiometric silicon nitride.

Nejadriahi, Hani↗

A Prototype High-Voltage Pulsed Power Supply for Control of the ITER Shattered Pellet Injection System Flyer Plate Valve

A high-voltage pulsed power supply (HVPPS) has been designed, prototyped, and tested for driving an eddy current actuated propellant valve for the International Thermonuclear Experimental Reactor (ITER) disruption mitigation system. The high-voltage (HV) dc supply output voltage is software programmable, and the energy storage capacitor bank can be readily reconfigured as 200, 400, 600, and 800 μ F, enabling testing and optimization of both the valve drive and valve systems. Multiple system parameters are monitored before, during, and after each firing of the valve. The system parameters are both displayed and stored for further analysis. Control of the setup, firing sequence, and data collection is automated using a LabVIEW-based control program. The programmability and reconfigurability of this system collectively provide a flexible and robust platform for system refinement and optimization. In this article, a summary of the system will be provided including operational sequences, HV switching and associated triggering methods and circuits, and results measured while firing a solid frozen pellet. Additionally, planned refinement activities toward meeting all requirements for ITER integration will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quantitative energy extraction measurements in a photoionization-stabilized self-sustained XeF laser

Detailed time-correlated gain, fluorescence, and laser energy measurements were used to obtain quantitative data on energy extraction efficiencies for a photoionization-stabilized self-sustained XeF laser. A current pulse of 25 ns full width at half-maximum produced an 80-cu-cm XeF plasma in NF3:Xe:He gas mixtures with a maximum output energy of 80 mJ. The results show that the maximum small-signal gain and the maximum specific output energy is proportional to the NF3 content of the gas mixture. This suggests that there is an optimum fractional utilization of the NF3 molecules in the discharge. Under high-gain conditions, 30-40% of the energy stored in XeF(asterisk) can be extracted in a gain-switched pulse. The output energy represents less than 1% of the input energy.

Lee, C. M.↗

Characterization and durability testing of plasma-sprayed zirconia-yttria and hafnia-yttria thermal barrier coatings. Part 1: Effect of spray parameters on the performance of several lots of partially stabilized zirconia-yttria powder

Initial experiments conducted on thermal barrier coatings prepared in the newly upgraded research plasma spray facility and the burner rig test facilities are discussed. Part 1 discusses experiments which establish the spray parameters for three baseline zirconia-yttria coatings. The quality of five similar coating lots was judged primarily by their response to burner rig exposure supplemented by data from other sources such as specimen characterizations and thermal diffusivity measurements. After allowing for burner rig variability, although there appears to be an optimum density (i.e., optimum microstructure) for maximum burner rig life, the distribution tends to be rather broad about the maximum. In Part 2, new hafnia-yttria-based coatings were evaluated against both baseline and alternate zirconia-yttria coatings. The hafnia-yttria coatings and the zirconia-yttria coatings that were prepared by an alternate powder vendor were very sensitive to plasma spray parameters, in that high-quality coatings were only obtained when certain parameters were employed. The reasons for this important observation are not understood. Also not understood is that the first of two replicate specimens sprayed for Part 1 consistently performed better than the second specimen. Subsequent experiments did not display this spray order affect, possibly because a chiller was installed in the torch cooling water circuit. Also, large changes in coating density were observed after switching to a new lot of electrodes. Analyses of these findings were made possible, in part, because of the development of a sensitive density measurement technique described herein in detail. The measured thermal diffusivities did not display the expected strong relationship with porosity. This surprising result was believed to have been caused by increased microcracking of the denser coatings on the stainless steel substrates.

Miller, Robert A.↗

ITER ECH Transmission Line System Design and Status

The electron cyclotron (EC) heating & current drive (H&CD) system on ITER provides plasma heating by generating, transmitting, and launching high-intensity, high-frequency (170 GHz) electromagnetic wave energy steerable across the plasma cross-section. The transmission line (TL) subsystem connects the Matching Optics Unit (MOU) on each of the 24 gyrotrons to the 32 feed points in the four upper launchers and the 24 feed points in the equatorial launcher. Each TL must be able to operate at up to 1.2 MW of input power for up to 1 hour pulse lengths. The TL system contains 50 mm water-cooled corrugated waveguide, 90o miter bends, 140o miter bends, polarizer miter bend pairs, switches, expansion units, pumpouts, DC breaks, MOU-TL adapters, Radio Frequency (RF) loads, and isolation shutter valves. A detailed finite element analysis has been used to verify the thermo-mechanical performance of each component. The microwave performance has been analyzed using a 2-D electromagnetic code combined with a Monte Carlo code. This approach allows the impact of manufacturing and installation tolerances to be assessed and optimized to provide a high probability of achieving the system performance requirements. Prototypes of the waveguide and TL components have been fabricated and tested at high-power. Production contracts are now being issued for fabrication and delivery of the waveguide and components to ITER.

Hanson, Gregory↗

Experiments and Computational Theory for Electrical Breakdown in Critical Components: THz Imaging of Electronic Plasmas.

This report describes the development of ultra-short pulse laser (USPL) induced terahertz (THz) radiation to image electronic plasmas during electrical breakdown. The technique uses three pulses from two USPLs to (1) trigger the breakdown, (2) create a 2 picosecond (ps, 10 -12 s), THz pulse to illuminate the breakdown, and (3) record the THz image of the breakdown. During this three year internal research program, sub-picosecond jitter timing for the lasers, THz generation, high bandwidth (BW) diagnostics, and THz image acquisition was demonstrated. High intensity THz radiation was optically-induced in a pulse-charged gallium arsenide photoconductive switch. The radiation was collected, transported, concentrated, and co-propagated through an electro-optic crystal with an 800 nm USPL pulse whose polarization was rotated due to the spatially varying electric field of the THz image. The polarization modulated USPL pulse was then passed through a polarizer and the resulting spatially varying intensity was detected in a high resolution digital camera. Single shot images had a signal to noise of %7E3:1. Signal to noise was improved to %7E30:1 with several experimental techniques and by averaging the THz images from %7E4000 laser pulses internally and externally with the camera and the acquisition system (40 pulses per readout). THz shadows of metallic films and objects were also recorded with this system to demonstrate free-carrier absorption of the THz radiation and improve image contrast and resolution. These 2 ps THz pulses were created and resolved with 100 femtosecond (fs, 10 -15 s) long USPL pulses. Thus this technology has the capability to time-resolve extremely fast repetitive or single shot phenomena, such as those that occur during the initiation of electrical breakdown. The goal of imaging electrical breakdown was not reached during this three year project. However, plans to achieve this goal as part of a follow-on project are described in this document. Further modifications to improve the THz image contrast and resolution are proposed, and after they are made, images of photo-induced carriers in gallium arsenide and silicon will be acquired to evaluate image sensitivity versus carrier density. Finally electrical breakdown will be induced with the first USPL pulse, illuminated with THz radiation produced with the second USPL pulse and recorded with the third USPL pulse.

36 MATERIALS SCIENCE↗

Electrical and thermal characteristics of LaB6 thermionic hollow cathodes operating in He, D2, Ar, and Xe at 4–200 Pa and 0.25–5 A cm−2

We report characteristics of lanthanum hexaboride (LaB6) cathodes for conditions relevant to a high-voltage, high-current switching device. LaB6 is selected because of its relatively low work function, stability in the presence of many common gas impurities, and a low evaporation rate (long life) at operating temperatures. We have investigated the effect of cathode geometry, gas type, pressure, and current on a LaB6 hollow cathode in a diode configuration with an opposing planar anode. The gas is stagnant at a relatively low pressure of 4–200 Pa (0.03–1.5 Torr) because of device high-voltage standoff requirements. In all cases, the plasma voltage decreases to a plateau value with increasing current where a practical device would operate. The plateau voltage aligns with the fill gas excitation or ionization voltage, depending on conditions. At high current, the cathode temperature exceeds that required for thermionic emission to supply the total current, a behavior that is understood by accounting for back-diffusing bulk electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Isolated Fast High-Voltage Switching Circuit

Electrically isolated switching circuit supplies pulses at potentials up to 6.5 kV and currents up to 6.5 A, lasting as long as few microseconds. Turn-on time about 40 ns; turn-off time about 3 microseconds. Electrically isolated from control circuitry by means of fiber-optic signal coupling and isolated power supply. Electrical isolation protects both technician and equipment. This and similar circuits useful in such industrial and scientific applications as high-voltage, high-frequency test equipment; electrostatic-discharge test equipment; plasma-laboratory instrumentation; spark chambers; and electromagnetic-interference test equipment.

Rizzi, Anthony↗

Momentum Transfer Studies and Studies of Linear and Nonlinear Optical Properties of Metal Colloids and Semiconductor Quantum Dots

Phase 1 of this work involved design work on a momentum transfer device. The progress on design and testing will be presented. Phase 2 involved the systematic study of the MPD thruster for dual uses. Though it was designed as a thruster for space vehicles, the characteristics of the plasma make it an excellent candidate for industrial applications. This project sought to characterize the system for use in materials processing and characterization. The surface modification on ZnCdTe, CdTe, and ZnTe will be presented. Phase 3 involved metal colloids and semiconductor quantum dots. One aspect of this project involves a collaborative effort with the Solid State Division of ORNL. The thrust behind this research is to develop ion implantation for synthesizing novel materials (quantum dots wires and wells, and metal colloids) for applications in all optical switching devices, up conversion, and the synthesis of novel refractory materials. The ions of interest are Au, Ag, Cd, Se, In, P, Sb, Ga, and As. The specific materials of interest are: CdSe, CdTe, InAs, GaAs, InP, GaP, InSb, GaSb, and InGaAs. A second aspect of this research program involves using porous glass (25-200 A) for fabricating materials of finite size. The results of some of this work will also be reported.

Collins, W. E.↗

Thermo-optic properties of silicon-rich silicon nitride for on-chip applications

We demonstrate the thermo-optic properties of silicon-rich silicon nitride (SRN) films deposited using plasma-enhanced chemical vapor deposition (PECVD). Shifts in the spectral response of Mach-Zehnder interferometers (MZIs) as a function of temperature were used to characterize the thermo-optic coefficients of silicon nitride films with varying silicon contents. A clear relation is demonstrated between the silicon content and the exhibited thermo-optic coefficient in silicon nitride films, with the highest achievable coefficient being as high as (1.65±0.08) ×10 −4 K -1 . Furthermore, we realize an SRN multi-mode interferometer (MMI) based thermo-optic switch with over 20 dB extinction ratio and total power consumption for two-port switching of 50 mW.

Nejadriahi, Hani↗

High‐Performance Zinc Tin Oxide TFTs with Active Layers Deposited by Atomic Layer Deposition

Abstract New deposition techniques for amorphous oxide semiconductors compatible with silicon back end of line manufacturing are needed for 3D monolithic integration of thin‐film electronics. Here, three atomic layer deposition (ALD) processes are compared for the fabrication of amorphous zinc tin oxide (ZTO) channels in bottom‐gate, top‐contact n‐channel transistors. As‐deposited ZTO films, made by ALD at 150–200 °C, exhibit semiconducting, enhancement‐mode behavior with electron mobility as high as 13 cm 2 V −1 s −1 , due to a low density of oxygen‐related defects. ZTO deposited at 200 °C using a hybrid thermal‐plasma ALD process with an optimal tin composition of 21%, post‐annealed at 400 °C, shows excellent performance with a record high mobility of 22.1 cm 2 V –1 s –1 and a subthreshold slope of 0.29 V dec –1 . Increasing the deposition temperature and performing post‐deposition anneals at 300–500 °C lead to an increased density of the X‐ray amorphous ZTO film, improving its electrical properties. By optimizing the ZTO active layer thickness and using a high‐ k gate insulator (ALD Al 2 O 3 ), the transistor switching voltage is lowered, enabling electrical compatibility with silicon integrated circuits. This work opens the possibility of monolithic integration of ALD ZTO‐based thin‐film electronics with silicon integrated circuits or onto large‐area flexible substrates.

Allemang, Christopher R.↗

Nucleoside-modified mRNA vaccines induce potent T follicular helper and germinal center B cell responses

T follicular helper (Tfh) cells are required to develop germinal center (GC) responses and drive immunoglobulin class switch, affinity maturation, and long-term B cell memory. In this study, we characterize a recently developed vaccine platform, nucleoside-modified, purified mRNA encapsulated in lipid nanoparticles (mRNA-LNPs), that induces high levels of Tfh and GC B cells. Intradermal vaccination with nucleoside-modified mRNA-LNPs encoding various viral surface antigens elicited polyfunctional, antigen-specific, CD4 + T cell responses and potent neutralizing antibody responses in mice and nonhuman primates. Importantly, the strong antigen-specific Tfh cell response and high numbers of GC B cells and plasma cells were associated with long-lived and high-affinity neutralizing antibodies and durable protection. Comparative studies demonstrated that nucleoside-modified mRNA-LNP vaccines outperformed adjuvanted protein and inactivated virus vaccines and pathogen infection. The incorporation of noninflammatory, modified nucleosides in the mRNA is required for the production of large amounts of antigen and for robust immune responses.

59 BASIC BIOLOGICAL SCIENCES↗

Ultrastructure of the green alga Dunaliella salina strain CCAP19/18 (Chlorophyta) as investigated by quick-freeze deep-etch electron microscopy

The single-celled green alga Dunaliella salina is a model system for studies on stress biology, in particular regarding secondary carotenoid accumulation. Under non-stress conditions the cells are green, but under abiotic stress the cells turn orange, because they switch their metabolism and accumulate β-Carotene in globules in the chloroplast. For the first time, Quick-freeze deep-etch electron microscopy was used to visualize cellular structures in green and orange cells of D. salina strain CCAP19/18. This allowed us to present an in-depth analysis of the cellular ultrastructure describing and comparing the features of the two cell types. Our images illustrate the presence of a pericellular matrix for this strain of D. salina. The pericellular matrix was spongy and strands of unknown material anchored it into the plasma membrane. The cytoplasm contained a variety of vesicles, vacuoles, and acidocalcisomes. We could show for strain CCAP19/18 that cytoplasmic lipid bodies were often in close proximity to and sometimes in contact with the outer chloroplast envelope membrane and with the endoplasmic reticulum. Major visible differences between green and orange cells were in the chloroplast: the orange cells have greatly reduced amounts of thylakoid membranes and greatly increased numbers of β-Carotene globules. We showed that the β-Carotene globules often made point contacts with thylakoid membranes, and frequently laid side-by-side along the thylakoid membrane surface, providing support to studies that indicated exchange of molecules between β-Carotene globules and thylakoid membranes. A unique finding was the β-Carotene globule duplets, suggesting intermediate stages in β-Carotene globule morphogenesis. Overall, the β-Carotene globules appear to be similar to plant plastoglobuli. We provide this description of the cellular ultrastructure features as a resource in the context of the recent publication of the genome of D. salina strain CCAP19/18 to expand on the knowledge regarding this novel reference strain.

59 BASIC BIOLOGICAL SCIENCES↗