Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phonon scattering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Differential multi-probe thermal transport measurements of multi-walled carbon nanotubes grown by chemical vapor deposition

Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m –1 K –1 at room temperature for a 9-walled MWCNT. In conclusion, theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.

42 ENGINEERING↗
NASA NTRS1972

One-phonon transitions observed in the scattering of He atoms from a LiF/001/ surface.

For the scattering of a nearly monoenergetic beam of thermal-energy He atoms from a cleaved (001)LiF crystal surface, speed distributions of the reflected atoms are measured at suitably spaced scattering angles within the plane of incidence. From the measurements, elastic and one-phonon inelastic scattering processes are identified. Elastically scattered atoms distribute themselves in a set of sharp diffraction peaks. One-phonon inelastically scattered atoms are dispersed about each diffraction peak. The most probable velocities of the inelastically scattered atoms exhibit a characteristic sawtooth variation with scattering angle which, to first approximation, corresponds to conservation of the component of atom momentum tangent to the surface.-

Fisher, S. S.↗
DOE OSTI2020

Coexistence of Soft Modes and Dynamic Ti Disorder in Cubic BaTiO 3 Studied by Inelastic Neutron Scattering

The phonon dispersion relations in cubic BaTiO 3 have been measured along the [100], [110], and [111] directions at T = 453 K using inelastic neutron scattering. The isotropic transverse acoustic (TA) branches indicate that the interatomic force constant between Ba and O atoms in BaTiO 3 is large compared with that between Pb and O atoms in PbTiO 3 . The transverse optical (TO) branches along the [100] and [111] directions soften toward the Brillouin zone center. The TO branch along the [110] direction with [001] polarization is relatively low and flat, indicating the weak interatomic force constant between Ti and O atoms along the Ti–O chain. The intensity of inelastic diffuse scattering along the [100] and [110] directions increases with decreasing temperature down to 453 K. In conclusion, the present results suggest that the soft modes coexist with the dynamic Ti disorder in the Ti–O chain near the phase transition in the cubic phase.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Beyond the Charge Transfer Mechanism for 2D Materials-Assisted Surface Enhanced Raman Scattering

Two-dimensional (2D) materials have been extensively implemented as surface-enhanced Raman scattering (SERS) substrates, enabling trace-molecule detection for broad applications. However, the accurate understanding of the mechanism remains elusive because most theoretical explanations are still phenomenological or qualitative based on simplified models and rough assumptions. To advance the development of 2D material-assisted SERS, it is vital to attain a comprehensive understanding of the enhancement mechanism and a quantitative assessment of the enhancement performance. Here, the microscopic chemical mechanism of 2D material-assisted SERS is quantitatively investigated. The frequency-dependent Raman scattering cross sections suggest that the 2D materials’ SERS performance is strongly dependent on the excitation wavelengths and the molecule types. By analysis of the microscopic Raman scattering processes, the comprehensive contributions of SERS can be revealed. Beyond the widely postulated charge transfer mechanisms, the quantitative results conclusively demonstrate that the resonant transitions within 2D materials alone are also capable of enhancing the molecular Raman scattering through the diffusive scattering of phonons. Furthermore, all of these scattering routines will interfere with each other and determine the final SERS performance. Our results not only provide a complete picture of the SERS mechanisms but also demonstrate a systematic and quantitative approach to theoretically understand, predict, and promote the 2D materials SERS toward analytical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Intrinsic anharmonicity and thermal properties of ultralow thermal conductivity Ba 6 Sn 6 Se 13

Ultralow thermal conductivity materials continue to be of great interest for technologically important applications such as thermal insulators and thermoelectrics. Often, such materials possess constituents with extensive dynamic disorder, or “rattlers,” or structural disorder such as metallic glasses. Nevertheless, targeted crystalline bonding order and anharmonicity can provide effective means for the scattering of the phonons in certain materials. Our combined experimental and theoretical investigation of Ba 6 Sn 6 Se 13 reveals such a material, with ultralow thermal conductivity measured over a large temperature range. Optic phonon modes hybridize with acoustic modes at relatively low energies resulting in strong acoustic-optic scattering and limited phonon lifetimes. Moreover, our investigations reveal various avoided crossings at low energies that contribute to phonon scattering. These are derived from chiral phase symmetries and may result in nontrivial topological behaviors for phonon band crossings in this chiral material. This work contributes to the ongoing research on low thermal conductivity materials and the underlying mechanisms that affect their thermal behaviors. Manipulation of these effects may provide pathways for enhancement of material properties for targeted thermal applications using similar materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phonon-informed Neural Thermal Scattering (NeTS) Optimization for Crystalline Graphite and Beryllium Metal

Fast neutrons born from fission lose energy through scattering interactions in the process of slowing-down. As neutrons thermalize to the order of $k$ $b$ $T$ (where $k$ $b$ is the Boltzmann constant, and $T$ is the temperature of the medium), their de Broglie wavelength and energy approaches the order of inter-atomic spacing and quantized lattice vibrations, i.e., phonons. At thermal energies, the thermal scattering law (TSL), i.e., $S$($α, β$), captures crystal binding contributions to the total reaction rate, or cross section. This dimensionless material property describes the energy ($β$) and momentum ($α$) exchanges available in a medium. Currently, $S$($α, β$) is evaluated in the Full Law Analysis Scattering System Hub (FLASSH) code for discrete inputs and stored as ENDF/B File 7 for 0-phonon elastic (MT 2) and n-phonon inelastic (MT 4) processes. Further processing recasts $S$($α, β$) into cumulative distribution functions for sampling post-collision scattering kinematics. In practice, interpolation schemes are employed to access data between tabulated values. An improvement to this juncture of the nuclear data pipeline is supplying cross sections on-the-fly (OTF), as has been developed for the un-resolved resonance region to minimize non-physical interpolation errors. This capability may improve simulation accuracy for accident and transient analyses, where rapidly varying changes in temperature and pressure are difficult to predict beforehand. To do so, deep artificial neural networks (ANNs) can be employed which collapse non-linear, complex data into a lightweight dictionary of neural weights and biases. This has been successfully demonstrated for the hydrogen in light water $S$($α, β$) dataset in the form of a Neural Thermal Scattering (NeTS) module. In this work, the NeTS framework is extended to consider the impact of material-dependent dynamical features on optimal neural pre-processing and architecture design decisions, such as number of neurons per hidden layer, residual skip connections and neural depth. New NeTS modules for crystalline graphite and beryllium metal illuminate a novel correlation between dynamical nonlinearity and optimal neural parametrization when deploying $S$($α, β$) on-the-fly.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Uncovering obscured phonon dynamics from powder inelastic neutron scattering using machine learning

The study of phonon dynamics is pivotal for understanding material properties, yet it faces challenges due to the irreversible information loss inherent in powder inelastic neutron scattering spectra and the limitations of traditional analysis methods. In this study, we present a machine learning framework designed to reveal obscured phonon dynamics from powder spectra. Using a variational autoencoder, we obtain a disentangled latent representation of spectra and successfully extract force constants for reconstructing phonon dispersions. Notably, our model demonstrates effective applicability to experimental data even when trained exclusively on physics-based simulations. The fine-tuning with experimental spectra further mitigates issues arising from domain shift. Analysis of latent space underscores the model’s versatility and generalizability, affirming its suitability for complex system applications. Furthermore, our framework’s two-stage design is promising for developing a universal pre-trained feature extractor. This approach has the potential to revolutionize neutron measurements of phonon dynamics, offering researchers a potent tool to decipher intricate spectra and gain valuable insights into the intrinsic physics of materials.

domain adaptation↗
DOE OSTI2022

Phonon thermal Hall effect in a metallic spin ice

It has become common knowledge that phonons can generate thermal Hall effect in a wide variety of materials, although the underlying mechanism is still controversial. We study longitudinal κ xx and transverse κ xy thermal conductivity in Pr 2 Ir 2 O 7 , which is a metallic analog of spin ice. Despite the presence of mobile charge carriers, we find that both κ xx and κ xy are dominated by phonons. A T/H scaling of κ xx unambiguously reveals that longitudinal heat current is substantially impeded by resonant scattering of phonons on paramagnetic spins. Upon cooling, the resonant scattering is strongly affected by a development of spin ice correlation and κ xx deviates from the scaling in an anisotropic way with respect to field directions. Strikingly, a set of the κ xx and κ xy data clearly shows that κ xy correlates with κ xx in its response to magnetic field including a success of the T/H scaling and its failure at low temperature. This remarkable correlation provides solid evidence that an indispensable role is played by spin-phonon scattering not only for hindering the longitudinal heat conduction, but also for generating the transverse response.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

GaSb doping facilitates conduction band convergence and improves thermoelectric performance in n-type PbS

P-type lead chalcogenides have superior thermoelectric performance because they exhibit the energy convergence of several valence bands. However, despite the existence of two conduction bands, there has been no report about conduction band (CB) convergence for n-type counterparts because of the large energy difference between them. Therefore, new strategies are required to manipulate the CBs if enhancing the electrical transport performance of n-type lead chalcogenides is to be achieved. PbS is a highly attractive member of the lead chalcogenides because of its high earth-abundance and low cost. Here, we report that the introduction of GaSb can successfully dope the PbS matrix with Ga and Sb atoms occupying the Pb site in its rock salt structure. GaSb doping leads to conduction band convergence and enlarged effective density of state mass for n-type PbS. This effect results in superior power factor and decreased lattice thermal conductivity caused by the soft phonon modes and point defect scattering of phonons. Consequently, a record-high average power factor PF avg of ~20.4 μW cm –1 K –2 and figure of merit ZT avg of ~0.84 in the temperature range of 400 K to 923 K were obtained, higher than any n- and p-type PbS-based thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Magneto-opto-phononic inverse Faraday effect

Nonlinear frequency conversion processes, such as optical rectification, difference-frequency generation, and sum-frequency generation, are fundamental for producing electromagnetic radiation at diverse frequencies. In this work, we demonstrate that coherently excited infrared-active phonons can act as transducers for generating nonlinear magnetizations through phonon-magnon interactions, analogous to nonlinear optical frequency conversion. We derive analytical solutions for the time-dependent magnetizations arising from the second-order response to the electric field component of an ultrashort laser pulse. These solutions enable us to define second-order nonlinear magneto-electric susceptibilities, which describe rectification, impulsive excitation, and sum-frequency excitation of coherent magnons. Our theoretical framework naturally incorporates the conventional magneto-optic and phonon inverse Faraday effects and predicts a hybrid magneto-opto-phononic inverse Faraday effect involving photon-phonon-magnon scattering. This work highlights nonlinear phononics as a pathway for controlling magnetization in solids.

Landau-Lifschitz-Gilbert equation↗
DOE OSTI2023

Ultrafast Carrier Drift Transport Dynamics in CsPbI3 Perovskite Nanocrystalline Thin Films

We study the early time carrier drift dynamics in CsPbI3 nanocrystal thin films with a sub 25 ps time resolution. Prior to trapping, carriers exhibit band-like transport characteristics, which is similar to those of traditional semiconductor solar absorbers including Si and GaAs due to optical phonon and carrier scattering at high temperatures. In contrast to the popular polaron scattering mechanism, the CsPbI3 nanocrystal thin film demonstrates the strongest optical phonon scattering mechanism among other inorganic-organic hybrid perovskites, Si, and GaAs. This ultrafast dynamics study establishes a foundation for understanding the fundamental carrier drift properties that drive perovskite nanocrystal optoelectronics.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2025

Time-Domain Extreme-Ultraviolet Diffuse Scattering Spectroscopy of Nanoscale Surface Phonons

Here, we report the observation of dynamic fringe patterns in the diffuse scattering of extreme ultraviolet light from surfaces, following femtosecond optical excitation. At each point on the detector, the diffuse scattering intensity exhibits oscillations at well-defined frequencies that correspond to surface phonons with wave vectors determined by the scattering geometry, indicating that the optical excitation generates coherent surface phonons propagating in all directions and spanning a wavelength range from 60 to 300 nm. This phenomenon is observed on a variety of samples, including single-layer and multilayer metal films, as well as bulk semiconductors. The measured surface phonon dispersions show good agreement with theoretical calculations. By comparing signal amplitudes from samples with different surface morphologies, we find that the excitation mechanism is linked to the natural surface roughness of the samples. However, the signal is still detectable on extremely smooth surfaces with subnanometer roughness. Our findings demonstrate a simple and effective method for optically exciting coherent surface phonons with nanoscale wavelengths on a wide range of solid samples and establish a foundation for surface phonon spectroscopy in a wave vector range well beyond the limit of conventional surface Brillouin scattering.

Capotondi, F. [Elettra-Sincrotrone Trieste (Italy)↗
DOE OSTI2022

Enhanced Electron Correlation and Significantly Suppressed Thermal Conductivity in Dirac Nodal-Line Metal Nanowires by Chemical Doping

Enhancing electron correlation in a weakly interacting topological system has great potential to promote correlated topological states of matter with extraordinary quantum properties. Here, the enhancement of electron correlation in a prototypical topological metal, namely iridium dioxide (IrO 2 ), via doping with 3d transition metal vanadium is demonstrated. Single-crystalline vanadium-doped IrO 2 nanowires are synthesized through chemical vapor deposition where the nanowire yield and morphology are improved by creating rough surfaces on substrates. Vanadium doping leads to a dramatic decrease in Raman intensity without notable peak broadening, signifying the enhancement of electron correlation. The enhanced electron correlation is further evidenced by transport studies where the electrical resistivity is greatly increased and follows an unusual $\sqrt{T}$ dependence on the temperature (T). The lattice thermal conductivity is suppressed by an order of magnitude via doping even at room temperature where phonon-impurity scattering becomes less important. Density functional theory calculations suggest that the remarkable reduction of thermal conductivity arises from the complex phonon dispersion and reduced energy gap between phonon branches, which greatly enhances phase space for phonon–phonon Umklapp scattering. This work demonstrates a unique system combining 3d and 5d transition metals in isostructural materials to enrich the system with various types of interactions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electrical conductivity of multilayered Cu/Nb composites fabricated by accumulative roll bonding

The electrical conductivity of nanolayered copper/niobium composites fabricated using accumulative roll bonding was investigated as a function of layer thickness. Cu/Nb was used as a model system to evaluate the processing-structure–property relationship stemming from the accumulative roll bonding process. The physical properties were compared against samples of individual average layer heights ranging from 193 to 25 nm. The electrical resistivity was measured over a temperature range of ~3–300 K. Analysis on the role of interfaces on temperature dependence is conducted including the residual resistivity ratio and temperature coefficient of resistivity. It was found that electrical resistivity increases with decreasing layer height.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Explaining the extra crystal-field mode in 𝐴 ⁢Ce ⁢𝑋 2 (𝐴 = K, Rb, Na; 𝑋 = O, S, Se, Te)

A growing list of Ce-based magnets have shown an extra and heretofore unexplained crystal electric field (CEF) mode at high energies. We describe a process whereby an optical phonon can produce a split CEF mode well above the phonon energy. We use density functional theory and point-charge model calculations to estimate the phonon distortions and coupling to model this effect in KCeO 2 , showing that it accounts for the extra CEF mode observed. Furthermore, this mechanism is generic and may explain the extra modes observed on a variety of Ce 3+ compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-frequency phonons drive large phonon-drag thermopower in semiconductors at high carrier density

It has been well established that (i) the thermopower of semiconductors can be enhanced through a phe- nomenon known as the drag effect, and (ii) the drag enhancement involves only low-frequency acoustic phonons and benefits from low electron densities and low temperatures. Using first-principles calculations we show that large drag enhancements to the thermopower are possible at high carrier density even at room temperature and arise from high-frequency acoustic phonons. A fascinating example is cubic boron arsenide (BAs) for which the calculated room temperature drag enhancement of the thermopower exceeds an order of magnitude at a high hole density of 10 21 cm –3 . This remarkable behavior stems from the simultaneously weak phonon-phonon and phonon-hole scattering of the high-frequency phonons in BAs that become drag active at high carrier densities through electron-phonon interactions. Furthermore, this work advances our understanding of coupled electron-phonon nanoscale transport and introduces an unexpected paradigm for achieving large thermopowers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Extreme sensitivity of higher-order interatomic force constants and thermal conductivity to the energy surface roughness of exchange-correlation functionals

In this Letter, we report that the fourth-order interatomic force constants (4th-IFCs) are significantly sensitive to the energy surface roughness of exchange-correlation (XC) functionals in density functional theory calculations. This sensitivity, which is insignificant for the second- (2nd-) and third-order (3rd-) IFCs, varies for different functionals in different materials and can cause misprediction of thermal conductivity by several times of magnitude. As a result, when calculating the 4th-IFCs using the finite difference method, the atomic displacement needs to be taken large enough to overcome the energy surface roughness, in order to accurately predict phonon lifetime and thermal conductivity. We demonstrate this phenomenon on a benchmark material (Si), a high-thermal conductivity material (BAs), and a low thermal conductivity material (NaCl). For Si, we find that the LDA, PBE, and PBEsol XC functionals are all smooth to the 2nd- and 3rd-IFCs but all rough to the 4th-IFCs. This roughness can lead to a prediction of nearly one order of magnitude lower thermal conductivity. For BAs, all three functionals are smooth to the 2nd- and 3rd-IFCs, and only the PBEsol XC functional is rough for the 4th-IFCs, which leads to a 40% underestimation of thermal conductivity. For NaCl, all functionals are smooth to the 2nd- and 3rd-IFCs but rough to the 4th-IFCs, leading to a 70% underprediction of thermal conductivity at room temperature. In conclusion, with these observations, we provide general guidance on the calculation of 4th-IFCs for an accurate thermal conductivity prediction.

42 ENGINEERING↗
DOE OSTI2021

Theory of Plasmonic Hot-Carrier Generation and Relaxation

Hot-carrier (HC) generation from (localized) surface plasmon decay has recently attracted much attention due to its promising applications in physical, chemical, materials, and energy science. However, the detailed mechanisms of plasmonic HC generation, relaxation, and trapping are less studied. In this work, we developed and applied a quantum-mechanical model and coupled master equation method to study the generation of HCs from plasmon decay and their following relaxation processes with different mechanisms treated on equal footing. First, a quantum-mechanical model for HC generation is developed. Its connection to existing semiclassical models and time-dependent density functional theory (TDDFT) is discussed. Second, the relaxation and lifetimes of HCs are investigated in the presence of electron–electron and electron–phonon interactions. A GW-like approximation is introduced to account for the electron–electron scattering. The numerical simulations on the Jellium nanoparticles with a size up to 1.6 nm demonstrate the electron–electron scattering and electron–phonon scattering dominate different time scale in the relaxation dynamics. We also generalize the model to study the extraction of HCs to attached molecules. The quantum yield of extracting HCs for other applications is found to be size-dependent. In general, the smaller size of NP improves the quantum yield, which is in agreement with recent experimental measurements. Even though we demonstrate this newly developed theoretical formalism with Jellium model, the theory applies to any other atomistic models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗