Results for “Porous structure” — Page 14

NASA NTRSDate not supplied

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗

NASA NTRS2010

Isolation of Resistance-Bearing Microorganisms

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Venkateswaran, Kasthuri, J.↗

NASA NTRS2010

Oscillating Cell Culture Bioreactor

To better exploit the principles of gas transport and mass transport during the processes of cell seeding of 3D scaffolds and in vitro culture of 3D tissue engineered constructs, the oscillatory cell culture bioreactor provides a flow of cell suspensions and culture media directly through a porous 3D scaffold (during cell seeding) and a 3D construct (during subsequent cultivation) within a highly gas-permeable closed-loop tube. This design is simple, modular, and flexible, and its component parts are easy to assemble and operate, and are inexpensive. Chamber volume can be very low, but can be easily scaled up. This innovation is well suited to work with different biological specimens, particularly with cells having high oxygen requirements and/or shear sensitivity, and different scaffold structures and dimensions. The closed-loop changer is highly gas permeable to allow efficient gas exchange during the cell seeding/culturing process. A porous scaffold, which may be seeded with cells, is fixed by means of a scaffold holder to the chamber wall with scaffold/construct orientation with respect to the chamber determined by the geometry of the scaffold holder. A fluid, with/without biological specimens, is added to the chamber such that all, or most, of the air is displaced (i.e., with or without an enclosed air bubble). Motion is applied to the chamber within a controlled environment (e.g., oscillatory motion within a humidified 37 C incubator). Movement of the chamber induces relative motion of the scaffold/construct with respect to the fluid. In case the fluid is a cell suspension, cells will come into contact with the scaffold and eventually adhere to it. Alternatively, cells can be seeded on scaffolds by gel entrapment prior to bioreactor cultivation. Subsequently, the oscillatory cell culture bioreactor will provide efficient gas exchange (i.e., of oxygen and carbon dioxide, as required for viability of metabolically active cells) and controlled levels of fluid dynamic shear (i.e., as required for viability of shear-sensitive cells) to the developing engineered tissue construct. This bioreactor was recently utilized to show independent and interactive effects of a growth factor (IGF-I) and slow bidirectional perfusion on the survival, differentiation, and contractile performance of 3D tissue engineering cardiac constructs. The main application of this system is within the tissue engineering industry. The ideal final application is within the automated mass production of tissue- engineered constructs. Target industries could be both life sciences companies as well as bioreactor device producing companies.

Freed, Lisa E.↗

NASA NTRS2003

Multilineage differentiation of rhesus monkey embryonic stem cells in three-dimensional culture systems

In the course of normal embryogenesis, embryonic stem (ES) cells differentiate along different lineages in the context of complex three-dimensional (3D) tissue structures. In order to study this phenomenon in vitro under controlled conditions, 3D culture systems are necessary. Here, we studied in vitro differentiation of rhesus monkey ES cells in 3D collagen matrixes (collagen gels and porous collagen sponges). Differentiation of ES cells in these 3D systems was different from that in monolayers. ES cells differentiated in collagen matrixes into neural, epithelial, and endothelial lineages. The abilities of ES cells to form various structures in two chemically similar but topologically different matrixes were different. In particular, in collagen gels ES cells formed gland-like circular structures, whereas in collagen sponges ES cells were scattered through the matrix or formed aggregates. Soluble factors produced by feeder cells or added to the culture medium facilitated ES cell differentiation into particular lineages. Coculture with fibroblasts in collagen gel facilitated ES cell differentiation into cells of a neural lineage expressing nestin, neural cell adhesion molecule, and class III beta-tubulin. In collagen sponges, keratinocytes facilitated ES cell differentiation into cells of an endothelial lineage expressing factor VIII. Exogenous granulocyte-macrophage colony-stimulating factor further enhanced endothelial differentiation. Thus, both soluble factors and the type of extracellular matrix seem to be critical in directing differentiation of ES cells and the formation of tissue-like structures. Three-dimensional culture systems are a valuable tool for studying the mechanisms of these phenomena.

Pluripotent Stem Cells/cytology/physiology↗

NASA NTRS1974

Structure and function of an inorganic-organic separator for electrochemical cells: Preliminary study

The structure of a new separator material for electrochemical cells has been investigated. Investigation into details of the separator structure showed it to be multilayered and to consist mainly of a quasi-impervious organic skin, a porous region of mixed organic and inorganic material, and an area of nonuniformly treated substrate. The essential feature of the coating (slurry) is believed to be interconnected pores which allow ionic conductivity. The interconnected pores are believed to be formed by the interaction of the plasticizer and inorganic fibers. The major failure mode of silver zinc cells using such a separator (zinc nodules shorting adjacent plates) was investigated.

Bozek, J. M.↗

NASA NTRS1988

New Acoustic Treatment For Aircraft Sidewalls

New aircraft-sidewall acoustic treatment reduces interior noise to acceptable levels and minimizes addition of weight to aircraft. Transmission of noise through aircraft sidewall reduced by stiffening device attached to interior side of aircraft skin, constrained-layer damping tape attached to stiffening device, porous acoustic materials of high resistivity, and relatively-soft trim panel isolated from vibrations of main fuselage structure.

Vaicaitis, Rimas↗

NASA NTRS1991

Gravitational Effects on Cellular Flame Structure

An experimental investigation has been conducted of the effect of gravity on the structure of downwardly propagating, cellular premixed propane-oxygen-nitrogen flames anchored on a water-cooled porous-plug burner. The flame is subjected to microgravity conditions in the NASA Lewis 2.2-second drop tower, and flame characteristics are recorded on high-speed film. These are compared to flames at normal gravity conditions with the same equivalence ratio, dilution index, mixture flow rate, and ambient pressure. The results show that the cellular instability band, which is located in the rich mixture region, changes little under the absence of gravity. Lifted normal-gravity flames near the cellular/lifted limits, however, are observed to become cellular when gravity is reduced. Observations of a transient cell growth period following ignition point to heat loss as being an important mechanism in the overall flame stability, dominating the stabilizing effect of buoyancy for these downwardly-propagating burner-anchored flames. The pulsations that are observed in the plume and diffusion flame generated downstream of the premixed flame in the fuel rich cases disappear in microgravity, verifying that these fluctuations are gravity related.

Dunsky, C. M.↗

NASA NTRS1999

Technology Demonstrator for Direct Polishing of a 50cm C/SiC Ultra Light Mirror

The NRSU portion of the contract was completed on schedule and within acceptable limits of the estimated cost. The lapping of the substrate started on schedule, and completed ahead of schedule. The polishing of the substrate was begun ahead of schedule, and was completed approximately one month ahead of schedule. It is our opinion that the substrate meets the requirements of "diffraction limited performance at 2 microns" over the measured 16 in. area. The final photos suggest that there may be edge roll-off beyond the 16 in. diameter. However, we cannot quantify this. It is our opinion that this material is suitable for use in lightweight optics as long as cladding of some type is used (Silicon, SiC, Sol-Gel, etc), as the bare material itself is too "porous" to obtain a high quality finish. We feel that this part was at the low limit of structural integrity required to mechanically polish to this level of figure requirement. Any lesser structural integrity would require some form of "non contact" figuring.

Scribner, Ken↗

NASA NTRS2001

Mechanical behavior in living cells consistent with the tensegrity model

Alternative models of cell mechanics depict the living cell as a simple mechanical continuum, porous filament gel, tensed cortical membrane, or tensegrity network that maintains a stabilizing prestress through incorporation of discrete structural elements that bear compression. Real-time microscopic analysis of cells containing GFP-labeled microtubules and associated mitochondria revealed that living cells behave like discrete structures composed of an interconnected network of actin microfilaments and microtubules when mechanical stresses are applied to cell surface integrin receptors. Quantitation of cell tractional forces and cellular prestress by using traction force microscopy confirmed that microtubules bear compression and are responsible for a significant portion of the cytoskeletal prestress that determines cell shape stability under conditions in which myosin light chain phosphorylation and intracellular calcium remained unchanged. Quantitative measurements of both static and dynamic mechanical behaviors in cells also were consistent with specific a priori predictions of the tensegrity model. These findings suggest that tensegrity represents a unified model of cell mechanics that may help to explain how mechanical behaviors emerge through collective interactions among different cytoskeletal filaments and extracellular adhesions in living cells.

NASA Discipline Cell Biology↗

NASA NTRS2016

Composite Cure Process Modeling and Simulations using COMPRO(Registered Trademark) and Validation of Residual Strains using Fiber Optics Sensors

Composite cure process induced residual strains and warping deformations in composite components present significant challenges in the manufacturing of advanced composite structure. As a part of the Manufacturing Process and Simulation initiative of the NASA Advanced Composite Project (ACP), research is being conducted on the composite cure process by developing an understanding of the fundamental mechanisms by which the process induced factors influence the residual responses. In this regard, analytical studies have been conducted on the cure process modeling of composite structural parts with varied physical, thermal, and resin flow process characteristics. The cure process simulation results were analyzed to interpret the cure response predictions based on the underlying physics incorporated into the modeling tool. In the cure-kinetic analysis, the model predictions on the degree of cure, resin viscosity and modulus were interpreted with reference to the temperature distribution in the composite panel part and tool setup during autoclave or hot-press curing cycles. In the fiber-bed compaction simulation, the pore pressure and resin flow velocity in the porous media models, and the compaction strain responses under applied pressure were studied to interpret the fiber volume fraction distribution predictions. In the structural simulation, the effect of temperature on the resin and ply modulus, and thermal coefficient changes during curing on predicted mechanical strains and chemical cure shrinkage strains were studied to understand the residual strains and stress response predictions. In addition to computational analysis, experimental studies were conducted to measure strains during the curing of laminated panels by means of optical fiber Bragg grating sensors (FBGs) embedded in the resin impregnated panels. The residual strain measurements from laboratory tests were then compared with the analytical model predictions. The paper describes the cure process procedures and residual strain predications, and discusses pertinent experimental results from the validation studies.

Sreekantamurthy, Thammaiah↗

NASA NTRS2004

Measurements of Acoustic Properties of Porous and Granular Materials and Application to Vibration Control

For application of porous and granular materials to vibro-acoustic controls, a finite dynamic strength of the solid component (frame) is an important design factor. The primary goal of this study was to investigate structural vibration damping through this frame wave propagation for various poroelastic materials. A measurement method to investigate the vibration characteristics of the frame was proposed. The measured properties were found to follow closely the characteristics of the viscoelastic materials - the dynamic modulus increased with frequency and the degree of the frequency dependence was determined by its loss factor. The dynamic stiffness of hollow cylindrical beams containing porous and granular materials as damping treatment was measured also. The data were used to extract the damping materials characteristics using the Rayleigh-Ritz method. The results suggested that the acoustic structure interaction between the frame and the structure enhances the dissipation of the vibration energy significantly.

Park, Junhong↗

NASA NTRS2004

Metal-Silicate Segregation in Deforming Dunitic Rocks: Applications to Core Formation in Europa and Ganymede

Core formation is an important event in the evolution of a planetary body, affecting both the geochemical and geophysical properties of the body. Metal-silicate segregation could have proceeded either by settling of liquid metal through a magma ocean or by percolation of liquid metal through a solid silicate mantle. Percolation of metallic melt had previously been excluded as a viable segregation mechanism because metallic melts do not form an interconnected network under hydrostatic conditions, except at high melt fraction (>5 vol%), due to the high dihedral angle between metals and silicates (>60 ). Without an interconnected network, porous flow of metallic melt is impossible, leaving the magma ocean scenario as the only mechanism to form the core. Moment-of-inertia measurements of Europa and Ganymede from the Galileo probe indicate that they are differentiated. This evidence suggests that a method for segregating metals and silicates at temperatures low enough to retain volatile compounds must exist. We have investigated the effect of deformation on the distribution of metallic melts in silicates. We have deformed samples of olivine + 5-9 vol% Fe-S to strains of 2.5 in simple shear and find that the metallic melt segregates into melt-rich planes oriented at 20 to the shear plane. These metallic melt-rich bands are similar in structure to the silicate melt-rich bands reported by Holtzman, indicating that deformation can interconnect isolated metallic melt pockets and allow porous flow of non-wetting melts. Such a core formation process could have occurred in the jovian satellites.

Hustoft, J. W.↗

NASA NTRS2003

Computational Study of Porous Treatment for Altering Flap Side-Edge Flowfield

Reynolds-averaged Navier-Stokes calculations are used to investigate porous side-edge treatment as a passive means for flap noise reduction. Steady-state simulations are used to infer effects of the treatment on acoustically relevant features of the mean flow near the flap side edge. Application of the porous treatment over a miniscule fraction of the wetted flap area (scaling with the flap thickness) results in significantly weaker side-edge vortex structures via modification of the vortex initiation and roll-up processes. At high flap deflections, the region of axial flow reversal associated with the breakdown of the side-edge vortex is also eliminated, indicating an absence of vortex bursting in the presence of the treatment. Potential ramifications of the mean-flow modifications for flap-noise reduction are examined in the light of lessons learned from recent studies on flap noise. Computations confirm that any noise reduction benefit via the porous treatment would be achieved without compromising the aerodynamic effectiveness of the flap. Results of the parameter study contribute additional insight into the measured data from the 7x10 wind tunnel at NASA Ames and provide preliminary guidance for specifying optimal treatment characteristics in terms of treatment location, spatial extent, and flow resistance of the porous skin.

Choudhari, Meelan↗

NASA NTRS2016

Transmission Electron Microscopy of Magnetite Plaquettes in Orgueil

Magnetite sometimes takes the form of a plaquette - barrel-shaped stack of magnetite disks - in carbonaceous chondrites (CC) that show evidence of aqueous alteration. The asymmetric nature of the plaquettes caused Pizzarello and Groy to propose magnetite plaquettes as a naturally asymmetric mineral that can indroduce symmetry-breaking in organic molecules. Our previous synchrotron X-ray computed microtomography (SXRCT) and electron backscatter diffraction (EBSD) analyses of the magnetite plaquettes in fifteen CCs indicate that magnetite plaquettes are composed of nearly parallel discs, and the crystallographic orientations of the discs change around a rotational axis normal to the discs surfaces. In order to further investigate the nanostructures of magnetite plaquettes, we made two focused ion beam (FIB) sections of nine magnetite plaquettes from a thin section of CI Orgueil for transmission electron microscope (TEM) analysis. The X-ray spectrum imaging shows that the magnetite discs are purely iron oxide Fe3O4 (42.9 at% Fe and 57.1 at% O), which suggest that the plaquettes are of aqueous origin as it is difficult to form pure magnetite as a nebular condensate. The selected area electron diffraction (SAED) patterns acquired across the plaquettes show that the magnetite discs are single crystals. SEM and EBSD analyses suggest that the planar surfaces of the magnetite discs belong to the {100} planes of the cubic inverse spinel structure, which are supported by our TEM observations. Kerridge et al. suggested that the epitaxial relationship between magnetite plaquette and carbonate determines the magnetite face. However, according to our TEM observation, the association of magnetite with porous networks of phyllosilicate indicates that the epitaxial relationship with carbonate is not essential to the formation of magnetite plaquettes. It was difficult to determine the preferred rotational orientation of the plaquettes due to the symmetry of the cubic structure, however, we are able to observe small but consistent rotational orientation across several discs within a plaquette.

Chan, Q. H. S.↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗

NASA NTRS1984

Design and performance analysis of a conical-aerobrake, orbital-transfer vehicle concept

A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, backscattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cis-lunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermal heating rates are also investigated. In addition, the structural and thermal-protection problems of the drag-brake support apparatus are analyzed and recommendations are proposed for future design refinements.

Menees, G. P.↗

NASA NTRS2009

Assessment of Soft Vane and Metal Foam Engine Noise Reduction Concepts

Two innovative fan-noise reduction concepts developed by NASA are presented - soft vanes and over-the-rotor metal foam liners. Design methodologies are described for each concept. Soft vanes are outlet guide vanes with internal, resonant chambers that communicate with the exterior aeroacoustic environment via a porous surface. They provide acoustic absorption via viscous losses generated by interaction of unsteady flows with the internal solid structure. Over-the-rotor metal foam liners installed at or near the fan rotor axial plane provide rotor noise absorption. Both concepts also provide pressure-release surfaces that potentially inhibit noise generation. Several configurations for both concepts are evaluated with a normal incidence tube, and the results are used to guide designs for implementation in two NASA fan rigs. For soft vanes, approximately 1 to 2 dB of broadband inlet and aft-radiated fan noise reduction is achieved. For over-the-rotor metal foam liners, up to 3 dB of fan noise reduction is measured in the low-speed fan rig, but minimal reduction is measured in the high-speed fan rig. These metal foam liner results are compared with a static engine test, in which inlet sound power level reductions up to 5 dB were measured. Brief plans for further development are also provided.

Jones, Michael G.↗