SEARCH · Search NASA

Results for “Range and range rate tracking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1960

Studies of the Retardation Force Developed on an Aircraft Tire Rolling in Slush or Water

A series of unbraked (freely rolling) taxi tests were conducted at the Langley landing-loads track with a 32 x 8.8, type 7, 22-ply-rating ribbed-tread aircraft tire to obtain data on tire retardation forces developed during rolling in both slush and water. The forward speeds of the tests ranged from 59 to 104 knots. Tire inflation pressures of 350 and 115 pounds per square inch were used. Results indicated a parabolic increase of retardation force with increasing forward velocity for both slush- and water-covered runway surfaces. The retardation force was found to increase approximately linearly with increasing water depth. Drag coefficients appropriate to the equations used are presented. Calculations made to determine the effect of slush on the take-off distance of a jet transport are in agreement with data obtained from an actual take-off in slush for this airplane. This is an interim report which deals with the effect of slush on the acceleration and the ground-run distance of airplanes during take-off.

Horne, Walter B.↗

NASA NTRS1983

AC propulsion system for an electric vehicle, phase 2

A second-generation prototype ac propulsion system for a passenger electric vehicle was designed, fabricated, tested, installed in a modified Mercury Lynx vehicle and track tested at the Contractor's site. The system consisted of a Phase 2, 18.7 kw rated ac induction traction motor, a 192-volt, battery powered, pulse-width-modulated, transistorized inverter packaged for under rear seat installation, a 2-axis, 2-speed, automatically-shifted mechanical transaxle and a microprocessor-based powertrain/vehicle controller. A diagnostics computer to assist tuning and fault finding was fabricated. Dc-to-mechanical-system efficiency varied from 78% to 82% as axle speed/torque ranged from 159 rpm/788 nm to 65 rpm/328 nm. Track test efficiency results suggest that the ac system will be equal or superior to dc systems when driving urban cycles. Additional short-term work is being performed under a third contract phase (AC-3) to raise transaxle efficiency to predicted levels, and to improve starting and shifting characteristics. However, the long-term challenge to the system's viability remains inverter cost. A final report on the Phase 2 system, describing Phase 3 modifications, will be issued at the conclusion of AC-3.

Slicker, J. M.↗

NASA NTRS1978

Investigations of Mars dynamics and geodesy via the Viking spacecraft

Results are reported for analyses of Doppler, ranging, and tracking data from the Viking landers and orbiters of relevance to the dynamics and geodesy of Mars. Highly improved numerical results are given for the orientation of the spin axis of Mars, the planet's sidereal rotation rate, and the earth-Mars ephemeris. A refined definition of the global gravitational field of Mars is discussed, a local gravitational survey based on Viking Orbiter 2 tracking data is described, and a mass anomaly near Olympus Mons is noted. Radius data are examined which suggest an asymmetry in the figure of Mars characterized by generally higher topography in the southern than in the northern hemisphere. The mass of Phobos is determined on the basis of Orbiter 1 orbital perturbations, and the mean density of this Martian satellite is found to be approximately 2.0 g/cu cm, which is suggestive of primitive carbonaceous chondrites and, if true, implies that Phobos was formed in the asteroid belt.

Michael, W. H., Jr.↗

NASA NTRS1978

ISEE-C solar wind plasma experiment

Two 135 deg spherical section electrostatic analyzers furnish electron and ion measurements of the solar wind on ISEE-C. Each of these instruments utilizes a divided secondary emitter system to intercept the analyzed particles. Secondary electrons selected from all of the emitters simultaneously provide fast two-dimensional measurements of the particle fluxes integrated over polar angle; at a slower rate secondary electrons are successively selected from individual emitters to provide three-dimensional measurements. Speed of the ion measurements is increased by a factor of two by using an active proton peak tracking system to reduce the total range of energy per charge which has to be covered.

Bame, S. J.↗

NASA NTRS2005

Space-Based Telemetry and Range Safety Project Ku-Band and Ka-Band Phased Array Antenna

The National Aeronautics and Space Administration Space-Based Telemetry and Range Safety study is a multiphase project to increase data rates and flexibility and decrease costs by using space-based communications assets for telemetry during launches and landings. Phase 1 used standard S-band antennas with the Tracking and Data Relay Satellite System to obtain a baseline performance. The selection process and available resources for Phase 2 resulted in a Ku-band phased array antenna system. Several development efforts are under way for a Ka-band phased array antenna system for Phase 3. Each phase includes test flights to demonstrate performance and capabilities. Successful completion of this project will result in a set of communications requirements for the next generation of launch vehicles.

Whiteman, Donald E.↗

NASA NTRS2005

Ku- and Ka-Band Phased Array Antenna for the Space-Based Telemetry and Range Safety Project

Whiteman, Donald E.↗

NASA NTRS2011

Measurement of CPAS Main Parachute Rate of Descent

The Crew Exploration Vehicle Parachute Assembly System (CPAS) is being designed to land the Orion Crew Module (CM) at a safe rate of descent at splashdown. Flight test performance must be measured to a high degree of accuracy to ensure this requirement is met with the most efficient design possible. Although the design includes three CPAS Main parachutes, the requirement is that the system must not exceed 33 ft/s under two Main parachutes, should one of the Main parachutes fail. Therefore, several tests were conducted with clusters of two Mains. All of the steady-state rate of descent data are normalized to standard sea level conditions and checked against the limit. As the Orion design gains weight, the system is approaching this limit to within measurement precision. Parachute "breathing," cluster interactions, and atmospheric anomalies can cause the rate of descent to vary widely and lead to challenges in characterizing parachute terminal performance. An early test had contradictory rate of descent results from optical trajectory and Differential Global Positioning Systems (DGPS). A thorough analysis of the data sources and error propagation was conducted to determine the uncertainty in the trajectory. It was discovered that the Time Space Position Information (TSPI) from the optical tracking provided accurate position data. However, the velocity from TPSI must be computed via numerical differentiation, which is prone to large error. DGPS obtains position through pseudo-range calculations from multiple satellites and velocity through Doppler shift of the carrier frequency. Because the velocity from DGPS is a direct measurement, it is more accurate than TSPI velocity. To remedy the situation, a commercial off-the-shelf product that combines GPS and an Inertial Measurement Unit (IMU) was purchased to significantly improve rate of descent measurements. This had the added benefit of solving GPS dropouts during aircraft extraction. Statistical probability distributions for CPAS Main parachute rate of descent and drag coefficient were computed and plotted. Using test data, a terminal rate of descent at splashdown can be estimated as a function of canopy loading.

Ray, Eric S.↗

NASA NTRS1991

Sub-nanosecond clock synchronization and precision deep space tracking

Interferometric spacecraft tracking is accomplished at the NASA Deep Space Network (DSN) by comparing the arrival time of electromagnetic spacecraft signals to ground antennas separated by baselines on the order of 8000 km. Clock synchronization errors within and between DSN stations directly impact the attainable tracking accuracy, with a 0.3 ns error in clock synchronization resulting in an 11 nrad angular position error. This level of synchronization is currently achieved by observing a quasar which is angularly close to the spacecraft just after the spacecraft observations. By determining the differential arrival times of the random quasar signal at the stations, clock synchronization and propagation delays within the atmosphere and within the DSN stations are calibrated. Recent developments in time transfer techniques may allow medium accuracy (50-100 nrad) spacecraft observations without near-simultaneous quasar-based calibrations. Solutions are presented for a global network of GPS receivers in which the formal errors in clock offset parameters are less than 0.5 ns. Comparisons of clock rate offsets derived from GPS measurements and from very long baseline interferometry and the examination of clock closure suggest that these formal errors are a realistic measure of GPS-based clock offset precision and accuracy. Incorporating GPS-based clock synchronization measurements into a spacecraft differential ranging system would allow tracking without near-simultaneous quasar observations. The impact on individual spacecraft navigation error sources due to elimination of quasar-based calibrations is presented. System implementation, including calibration of station electronic delays, is discussed.

Charles Dunn↗

NASA NTRS1981

Optical deep space communication via relay satellite

The possible use of an optical for high rate data transmission from a deep space vehicle to an Earth-orbiting relay satellite while RF links are envisioned for the relay to Earth link was studied. A preliminary link analysis is presented for initial sizing of optical components and power levels, in terms of achievable data rates and feasible range distances. Modulation formats are restricted to pulsed laser operation, involving bot coded and uncoded schemes. The advantage of an optical link over present RF deep space link capabilities is shown. The problems of acquisition, pointing and tracking with narrow optical beams are presented and discussed. Mathematical models of beam trackers are derived, aiding in the design of such systems for minimizing beam pointing errors. The expected orbital geometry between spacecraft and relay satellite, and its impact on beam pointing dynamics are discussed.

Gagliardi, R. M.↗

NASA NTRS1991

Charged particle LET-spectra measurements aboard LDEF

The linear energy transfer (LET) spectra of charged particles was measured in the 5 to 250 keV/micron (water) interval with CR-39 and in the 250 to 1000 keV/micron (water) interval with polycarbonate plastic nuclear track detectors (PNTDs) under different shielding depths in the P0006 experiment. The optimal processing conditions were determined for both PNTDs in relation to the relatively high track densities due to the long term exposure in space. The total track density was measured over the selected samples, and tracks in coincidence on the facing surfaces of two detector sheets were selected for measuring at the same position on each sheet. The Short Range (SR) and Galactic Cosmic Ray (GCR) components were measured separately. The integral dose and dose rate spectra of charged particles are also given. The high LET portion of the LET spectra was measured with high statistical accuracy. This is a unique result of this experiment due to the low flux of this type of particle under typical shielding conditions.

Csige, I.↗

NASA NTRS2016

Application of X-Ray Pulsar Navigation: A Characterization of the Earth Orbit Trade Space

The potential for pulsars as a navigation source has been studied since their discovery in 1967. X-ray pulsar navigation (XNAV) is a celestial navigation system that uses the consistent timing nature of x-ray photons from milli-second pulsars (MSP) to perform space navigation. By comparing the detected arrival of x-ray photons to a reference database of expected pulsar lightcurve timing models, one can infer a range and range rate measurement based on light time delay. Much of the challenge of XNAV comes from the faint signal, availability, and distant nature of pulsars. This is a study of potential pulsar XNAV measurements to measure extended Kalman filter (EKF) tracking performance with a wide trade space of bounded Earth orbits, using a simulation of existing x-ray detector space hardware. An example of an x-ray detector for XNAV is the NASA Station Explorer for X-ray Timing and Navigation (SEXTANT) mission, a technology demonstration of XNAV set to perform on the International Space Station (ISS) in late 2016early 2017. XNAV hardware implementation is driven by trajectory and environmental influences which add noise to the x-ray pulse signal. In a closed Earth orbit, the radiation environment can exponentially increase the signal noise from x-ray pulsar sources, decreasing the quality and frequency of measurements. The SEXTANT mission in particular improves on the signal to noise ratio by focusing an array of 56 x-ray silicon drift detectors at one pulsar target at a time. This reduces timing glitches and other timing noise contributions from ambient x-ray sources to within a 100 nanosecond resolution. This study also considers the SEXTANT scheduling challenges inherent in a single target observation. Finally, as the navigation sources are now relatively inertial targets, XNAV measurements are also subject to periods of occultation from various celestial bodies. This study focuses on the characterization of these drivers in closed Earth orbits and is not a tuning analysis of the EKF. The study shows that the closed Earth orbit for XNAV performance is reliant on the orbit semi-major axis and eccentricity as well as orbit inclination. These parameters are the primary drivers of pulsar measurement availability and significantly influence the natural spacecraft orbit dynamics. Sensitivity to initial orbit determination error growth due to the scarcity of XNAV measurements within an orbital period require appropriate timing of initial XNAV measurements. The orbit angles of argument of perigee and right ascension of the ascending node, alongside the other orbit parameters, complete the initial cadence of XNAV measurements. The performance of initial XNAV measurements then propagates throughout the experimental period. The study provides a basis to missions who wish to consider XNAV as a potential navigation source in a closed Earth orbit design. It provides a family of orbit trajectories as well as other modeling considerations needed to effectively evaluate if XNAV is an effective navigation source for a potential mission. As an EKF is sensitive to a linearized estimated state, this study has a direct benefit of providing effective XNAV measurements to maintain spacecraft tracking, independent of other navigation sources. In the particular use case of the SEXTANT mission, it also provides a novel scheduling algorithm which addresses the need to prioritize and manage pulsar observations for effective navigation.

PULSAR↗

NASA NTRS2016

Application of X-Ray Pulsar Navigation: A Characterization of the Earth Orbit Trade Space

The potential for pulsars as a navigation source has been studied since their discovery in 1967. X-ray pulsar navigation (XNAV) is a celestial navigation system that uses the consistent timing nature of x-ray photons from millisecond pulsars (MSP) to perform space navigation. By comparing the detected arrival of x-ray photons to a reference database of expected pulsar light-curve timing models, one can infer a range and range rate measurement based on light time delay. Much of the challenge of XNAV comes from the faint signal, availability, and distant nature of pulsars. This is a study of potential pulsar XNAV measurements to measure extended Kalman filter (EKF) tracking performance with a wide trade space of bounded Earth orbits, using a simulation of existing x-ray detector space hardware. An example of an x-ray detector for XNAV is the NASA Station Explorer for X-ray Timing and Navigation (SEXTANT) mission, a technology demonstration of XNAV set to perform on the International Space Station (ISS) in late 2016early 2017. XNAV hardware implementation is driven by trajectory and environmental influences which add noise to the x-ray pulse signal. In a closed Earth orbit, the radiation environment can exponentially increase the signal noise from x-ray pulsar sources, decreasing the quality and frequency of measurements. The SEXTANT mission in particular improves on the signal to noise ratio by focusing an array of 56 x-ray silicon drift detectors at one pulsar target at a time. This reduces timing glitches and other timing noise contributions from ambient x-ray sources to within a 100 nanosecond resolution. This study also considers the SEXTANT scheduling challenges inherent in a single target observation. Finally, as the navigation sources are now relatively inertial targets, XNAV measurements are also subject to periods of occultation from various celestial bodies. This study focuses on the characterization of these drivers in closed Earth orbits and is not a tuning analysis of the EKF. The study shows that the closed Earth orbit for XNAV performance is reliant on the orbit semi-major axis and eccentricity as well as orbit inclination. These parameters are the primary drivers of pulsar measurement availability and significantly influence the natural spacecraft orbit dynamics. Sensitivity to initial orbit determination error growth due to the scarcity of XNAV measurements within an orbital period require appropriate timing of initial XNAV measurements. The orbit angles of argument of perigee and right ascension of the ascending node, alongside the other orbit parameters, complete the initial cadence of XNAV measurements. The performance of initial XNAV measurements then propagates throughout the experimental period. The study provides a basis to missions who wish to consider XNAV as a potential navigation source in a closed Earth orbit design. It provides a family of orbit trajectories as well as other modeling considerations needed to effectively evaluate if XNAV is an effective navigation source for a potential mission. As an EKF is sensitive to a linearized estimated state, this study has a direct benefit of providing effective XNAV measurements to maintain spacecraft tracking, independent of other navigation sources. In the particular use case of the SEXTANT mission, it also provides a novel scheduling algorithm which addresses the need to prioritize and manage pulsar observations for effective navigation.

x-ray↗

NASA NTRS2003

Assimilation of Precipitation Information Retrieved from Passive Microwave Sensors

Estimates of surface precipitation and the associated vertical latent heating structure can be retrieved from space-borne passive microwave sensors such as the TRMM Microwave Imager (TMI) and Special Sensor Microwave/Imager (SSM/I). Studies have shown that assimilation of microwave rain rates can improve the quality of global analysis and forecast. Numerical weather prediction (NWP) centers are beginning to make operational use of these data. In the next few years, there will be a gradual increase in microwave rain products available from operational and research satellites, culminating to a target constellation of 9 satellites to provide global rain measurements every 3 hours with the proposed Global Precipitation Measurement (GPM) mission to be launched around 2007. Realizing the full potential of these observations in data assimilation will require continued advances in retrieval algorithms, assimilation techniques, and model physics. I present results from two research efforts at NASA GSFC. The first is on the assimilation of tropical precipitation using temperature/moisture tendency corrections within a continuous variational assimilation framework to improve analyses and forecasts produced by the Goddard Earth Observing System (GEOS) global data assimilation system. Results show that assimilation of TMI and SSM/I rain rates improves not only precipitation and moisture, but also the related clouds, radiation energy fluxes, and large-scale circulations in GEOS analyses. The improved analyses also yield better short-range forecasts, quantitative precipitation forecast (QPF) threat scores, and storm track predictions. The second part consists of results from exploratory experiments on variational assimilation of convective and stratiform latent heating profiles within the general framework of model parameter estimation as a way to identify systematic model errors and optimize physical paremeterization schemes in global forecast and climate models.

Hou, Arthur Y.↗

NASA NTRS1992

Flight evaluation of differential GPS aided inertial navigation systems

Algorithms are described for integration of Differential Global Positioning System (DGPS) data with Inertial Navigation System (INS) data to provide an integrated DGPS/INS navigation system. The objective is to establish the benefits that can be achieved through various levels of integration of DGPS with INS for precision navigation. An eight state Kalman filter integration was implemented in real-time on a twin turbo-prop transport aircraft to evaluate system performance during terminal approach and landing operations. A fully integrated DGPS/INS system is also presented which models accelerometer and rate-gyro measurement errors plus position, velocity, and attitude errors. The fully integrated system was implemented off-line using range-domain (seventeen-state) and position domain (fifteen-state) Kalman filters. Both filter integration approaches were evaluated using data collected during the flight test. Flight-test data consisted of measurements from a 5 channel Precision Code GPS receiver, a strap-down Inertial Navigation Unit (INU), and GPS satellite differential range corrections from a ground reference station. The aircraft was laser tracked to determine its true position. Results indicate that there is no significant improvement in positioning accuracy with the higher levels of DGPS/INS integration. All three systems provided high-frequency (e.g., 20 Hz) estimates of position and velocity. The fully integrated system provided estimates of inertial sensor errors which may be used to improve INS navigation accuracy should GPS become unavailable, and improved estimates of acceleration, attitude, and body rates which can be used for guidance and control. Precision Code DGPS/INS positioning accuracy (root-mean-square) was 1.0 m cross-track and 3.0 m vertical. (This AGARDograph was sponsored by the Guidance and Control Panel.)

Mcnally, B. David↗

NASA NTRS1991

The Advanced Receiver II telemetry test results at Goldstone

The telemetry performance of the Advanced Receiver II (ARX-II) in tracking and demodulating signals from various deep space missions is described. The tests were performed at Goldstone, and the spacecrafts tracked were Pioneer 10, Pioneer 11, Voyager 2, Magellan, and the International Cometary Explorer (ICE). These missions present a broad range of operating conditions to test the ARX-II in terms of signal-to-noise ratio (SNR) and the symbol rate of the received signal.

Sadr, R.↗

NASA NTRS2003

Acquisition, Tracking, and Pointing Using Earth Thermal Images for Deep Space Optical Communications

The feasibility of using long wavelength Earth thermal (infrared) images for telescope tracking/pointing application. for both Deep Space Free- pace Optical Communications has been investigated and is reported her. The advantage of this technology rests on using full Earth images in this band, which yield more accurate estimates of geometric centroids than that of Earth images in the visible band. Another major advantage is that these images are nearly independent of Earth phase angle. The results of the study show that at a Mars range, with currently available sensors, a noise equivalent angle of 10 to 150 nanoradians and a bias error of better than 80 nanoradians can be obtained. This enables precise pointing of the optical communications beam for high data rate links.

free-space optical communication↗

NASA NTRS1985

Search for TeV gamma rays from extragalactic sources and the Galactic Center

The Ooty atmospheric Cerenkov array was used in 1982-83 to see if the galactic center and the extra-galactic sources 3C 273, Centaurus A emit gamma rays at TeV energies. The ON/OFF method was used wherein the source was tracked for 16 minutes and immediately afterwards, a background region in the same zenith angle range was tracked for the next 16 minutes. Data were taken for approx 15 hours (55 scans) on 3C273, approx 7 hours (26 scans) on Cen A and 5 hours (19 scans) on galactic center. A preliminary analysis involving direct comparison of total rates on and off the source shows no significant excess from any of these orbits. Results of detailed analysis using different energy thresholds are presented.

Bhat, P. N.↗

NASA NTRS1996

Neutron fluences and dose equivalents measured with passive detectors on LDEF

Neutron fluences were measured on LDEF in the low energy (< 1 MeV) and high energy (> 1 MeV) ranges. The low energy detectors used the 6Li(n,alpha)T reaction with Gd foil absorbers to separate thermal (< 0.2 eV) and resonance (0.2 eV-1 MeV) neutron response. High energy detectors contained sets of fission foils (181Ta, 209Bi, 232Th, 238U) with different neutron energy thresholds. The measured neutron fluences together with predicted spectral shapes were used to estimate neutron dose equivalents. The detectors were located in the A0015 and P0006 experiments at the west and Earth sides of LDEF under shielding varying from 1 to 19 g/cm2. Dose equivalent rates varied from 0.8 to 3.3 microSv/d for the low energy neutrons and from 160 to 390 microSv/d for the high energy neutrons. This compares with TLD measured absorbed dose rates in the range of 1000-3000 microGy/d near these locations and demonstrates that high energy neutrons contribute a significant fraction of the total dose equivalent in LEO. Comparisons between measurements and calculations were made for high energy neutrons based on fission fragment tracks generated by fission foils at different shielding depths. A simple 1-D slab geometry was used in the calculations. Agreement between measurements and calculations depended on both shielding depth and threshold energy of the fission foils. Differences increased as both shielding and threshold energy increased. The modeled proton/neutron spectra appeared deficient at high energies. A 3-D model of the experiments is needed to help resolve the differences.

LDEF Project↗