Results for “Reconstruction” — Page 14

NASA NTRS2019

InSight's Reconstructed Aerothermal Environments

The InSight Mars Lander successfully landed on the surface on November 26, 2018. This poster will describe the methodologies and margins used in developing the aerothermal environments for design of the thermal protection systems (TPS), as well as a prediction of as-flown environments based on the best estimated trajectory. The InSight mission spacecraft design approach included the effects of radiant heat flux to the aft body from the wake for the first time on a US Mars Mission, due to overwhelming evidence in ground testing for the European ExoMars mission (2009/2010) [1] and 2010 tests in the Electric Arc Shock Tube (EAST) facility [2]. The radiant energy on an aftbody was also recently confirmed via measurement on the Schiaparelli mission [3]. In addition, the InSight mission expected to enter the Mars atmosphere during the dust storm season, so the heatshield TPS was designed to accommodate the extra recession due to the potential dust impact. This poster will compare the predicted aerothermal environments using the reconstructed best estimated trajectory to the design environments. Design Approach: The InSight spacecraft was planned to be a near-design-to-print copy of the Phoenix spacecraft. The determination of the heatshield TPS requirements was approached as if it was a new design due to the new requirement of flying through a dust storm. The baseline for aftbody was build-to-print, and all analyses focused on ensuring adequate margin. This proved to be a challenge because the Phoenix aftbody was designed to withstand only convective heating and the InSight aftbody was evaluated for both convective and radiative heating. Aerothermal environments were predicted using the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) and the Data Parallel Line Relaxation (DPLR) CFD codes, and the Nonequilibrium Radiative Transport and Spectra Program (NEQAIR) utilizing bounding design trajectories derived from Monte Carlo analyses from the Program to Optimize Simulated Trajectories II (POST2). In all cases, super-catalytic flowfields were assigned to ensure the most conservative heating results. Two trajectories were evaluated: 1) the trajectory with the maximum heat flux was utilized to determine the flowfield characteristics and the viability of the selection of TPS materials; and 2) the trajectory with the maximum heat load was used to determine the required thicknesses of the TPS materials. Evaluation of the MEDLI data [4], along with ground test data [5] led to the determination of whether or not the flow would transition from laminar to turbulent on the heatshield, which also determined the TPS sizing location for the heatshield. Aerothermal margins were added for the convective heating and developed for the radiative heating. TPS material sizing was determined with the Reaction Kinetic Ablation Program (REKAP) and the Fully Implicit Ablation and Thermal Analysis program (FIAT) using a three-branched approach to account for aerothermal, material response, and material properties uncertainties. In addition, the heatshield recession was augmented by an analysis of the effect of entry through a potential dusty atmosphere using a methodology developed in References [6] and [7]. These analyses resulted in an increase to the Phoenix heatshield TPS thickness. Reconstruction Efforts: Once the best estimated trajectory is reconstructed by the team, the LAURA/HARA (High-Temperature Aerothermo-dynamic Radiation model) and DPLR/NEQAIR code pairs will be used to predict the as-flown aerothermal conditions. In these runs, fully-catalytic flowfields will be assigned because it is a more physically accurate description of the chemistry in the flow. Once again, determination of the onset of turbulence on the heatshield will be evaluated. The as-flown aerothermal environments will then be compared to the design environments.

Beck, R. A.↗

NASA NTRSDate not supplied

Mars InSight Entry, Descent, and Landing Trajectory and Atmosphere Reconstruction

The InSight mission landed on the surface of Mars on November 26th, 2018. The InSight system performance met all design requirements, although several performance metrics fell near the boundaries of the predictions. The peak deceleration was high, the overall timeline was short, and the landing site was uprange and crossrange from the target. This paper describes the reconstruction of the entry, descent, and landing trajectory and atmosphere. The approach utilizes a Kalman filter to blend sensor data to obtain the vehicle trajectory. The aerodynamic database is used in combination with the sensed accelerations to obtain estimates of the atmosphere-relative state, which in turn is used to derive the free-stream atmospheric conditions during entry, until the time of parachute deployment. The results indicate that the reconstructed atmosphere was approximately 1σbelow the preflight atmosphere. Analysis of the reconstructed vehicle attitude angles indicate that the aerodynamic lift was oriented downward at entry. The vehicle developed a roll rate during entry, which directed a component of the lift to the north. The low density and aerodynamic lift direction are determined to be the primary causes of the high deceleration, short timeline, and location of the landing site relative to the target.

Christopher D Karlgaard↗

NASA NTRS2020

Mars InSight Entry, Descent, and Landing Trajectory and Atmosphere Reconstruction

The InSight mission landed on the surface of Mars on November 26th, 2018. The InSight system performance met all design requirements, although several performance metrics fell near the boundaries of the predictions. The peak deceleration was high, the overall timeline was short, and the landing site was uprange and crossrange from the target. This paper describes the reconstruction of the entry, descent, and landing trajectory and atmosphere. The approach utilizes a Kalman filter to blend sensor data to obtain the vehicle trajectory. The aerodynamic database is used in combination with the sensed accelerations to obtain estimates of the atmosphere-relative state, which in turn is used to derive the free-stream atmospheric conditions during entry, until the time of parachute deployment. The results indicate that the reconstructed atmosphere was approximately 1σbelow the preflight atmosphere. Analysis of the reconstructed vehicle attitude angles indicate that the aerodynamic lift was oriented downward at entry. The vehicle developed a roll rate during entry, which directed a component of the lift to the north. The low density and aerodynamic lift direction are determined to be the primary causes of the high deceleration, short timeline, and location of the landing site relative to the target.

Christopher D Karlgaard↗

NASA NTRS2018

Occluded Object Reconstruction for First Responders with Augmented Reality Glasses Using Conditional Generative Adversarial Networks

Firefighters suffer a variety of life-threatening risks, including line-of-duty deaths, injuries, and exposures to hazardous substances. Support for reducing these risks is important. We built a partially occluded object reconstruction method on augmented reality glasses for first responders. We used a deep learning based on conditional generative adversarial networks to train associations between the various images of flammable and hazardous objects and their partially occluded counterparts. Our system then reconstructed an image of a new flammable object. Finally, the reconstructed image was superimposed on the input image to provide "transparency". The system imitates human learning about the laws of physics through experience by learning the shape of flammable objects and the flame characteristics.

Chow, Edward↗

NASA NTRSDate not supplied

Three-Dimensional Instantaneous Flow-field Reconstruction Using Planar Spectral Proper Orthogonal Decomposition

A novel method for three-dimensional flowfield reconstruction is presented that utilizes spectral proper orthogonal decomposition (SPOD). The time-resolved PIV data are acquired in multiple two-dimensional spanwise planes, with adequate streamwise spacing to resolve the out-of-plane wavelength. Knowledge of the out-of-plane phase speed is also required, and for the present case this value was obtained using instantaneous hot-wire measurements. The method is validated by comparing phase-averaged results acquired with a forcing signal to the SPOD reconstructed results using the same data. The method is also applied to data with no forcing applied, and the results are shown to be similar to the forced case. This method is particularly useful for cases in which there are multiple frequencies of interest, or cases in which the phenomena occur over a broad range of frequencies. This method allows reconstruction of the frequencies of interest without the need for a forcing signal, so the flow can be studied in its natural (undisturbed) state.

boundary-layer transition↗

NASA NTRSDate not supplied

Attitude Reconstruction of Free-Flight CFD Generated Trajectories Using Non-Linear Pitch Damping Coefficient Curves

Attitude history reconstruction of Free-flight CFD generated trajectories with non-linear pitch damping coefficient curves is investigated. Free-flight CFD simulations of the capsule shape used for the Genesis sample return mission and the upcoming Dragonfly mission to Titan are conducted for 1-, 2-, and 3-degree-of-freedom cases. Two different data reduction methodologies are employed to derive a pitch damping curve as a function of instantaneous angle of attack. These curves are then used to reconstruct the attitude history of the body which is compared to the raw simulation results. While both data reduction methods produce pitch damping curves that can generally reconstruct the motion seen in the Free-flight simulations, it is found that optimization of the pitch damping curve using an inverse estimation process yields superior and more generalizable results. Further refinement of this technique could allow pitch damping curves derived using CFD to serve as a capability complementary to existing techniques for dynamic stability characterization.

entry↗

NASA NTRSDate not supplied

Attitude Reconstruction of Free-Flight CFD Generated Trajectories Using Non-Linear Pitch Damping Coefficient Curves

Attitude history reconstruction of Free-flight CFD generated trajectories with non-linear pitch damping coefficient curves is investigated. Free-flight CFD simulations of the capsule shape used for the Genesis sample return mission and the upcoming Dragonfly mission to Titan are conducted for 1-, 2-, and 3-degree-of-freedom cases. Two different data reduction methodologies are employed to derive a pitch damping curve as a function of instantaneous angle of attack. These curves are then used to reconstruct the attitude history of the body which is compared to the raw simulation results. While both data reduction methods produce pitch damping curves that can generally reconstruct the motion seen in the Free-flight simulations, it is found that optimization of the pitch damping curve using an inverse estimation process yields superior and more generalizable results. Further refinement of this technique could allow pitch damping curves derived using CFD to serve as a capability complementary to existing techniques for dynamic stability characterization.

entry↗

NASA NTRSDate not supplied

Field Reconstruction from PIV Measurements Employing Bernstein Polynomial Derived Operators

A fluid-dynamic reconstruction algorithm is presented that generates a least-squares best-fit, two-dimensional density field from a prespecified two-dimensional velocity field. This method recasts the mass-conservation equation as a modified Sylvester equation employing high-order operators derived from modified Bernstein polynomial expansions. To demonstrate its practical utility, this analytic methodology is applied to two canonical cases and a Particle Image Velocimetry dataset obtained from a Mach-2, mechanically back-pressured, isolator experiment. This methodology is envisioned to be used in conjunction with hypersonic-diagnostic techniques to aid in the quantification of isolator flow fields. However, also note that this reconstruction technique is well suited to other applications relevant to fluid dynamics, such as obtaining three-dimensional flow field reconstructions.

Bernstein Polynomials↗

NASA NTRSDate not supplied

Flow field Reconstruction for Inhomogeneous Turbulence using Data and Physics Driven Models

A methodology combining Large Eddy Simulation (LES) trained data and a physics driven wave packet model to obtain a reduced order reconstruction for broadband, three-dimensional, temporally stationary but spatially inhomogeneous, incompressible turbulence. Wake turbulence generated by an axisymmetric dragging disk with a turbulent co-flow serves as the benchmark test case. We begin by studying the proper-orthogonal decomposition of the turbulent fluctuations taken from a high-resolution LES to first identify whether the fields demonstrate a low-rank character. It is argued that the presence of the turbulent co-flow results in a largely broadband character lacking any tonal properties. This is especially true for Strouhal numbers greater than 1 and only a small fraction of energy is contained in the leading order Kelvin-Helmholtz modes. As such reconstructions and reduced order modeling purely relying on data from LES does not appear to be a lucrative solution - contrary to problems with strongly tonal character. To supplement the missing energy from a low order truncated mode expansion, we utilize a physics based super-resolution (enrichment) algorithm that relies on spatio-temporally localized Gabor wave packets whose time evolution is described using a set of ordinary differential equations. The reconstructed flow has single- and two-point correlations that are consistent with the reference high resolution simulation data.

SLS↗

NASA NTRSDate not supplied

Evaluation of Artemis I Aerodynamic Force and Moment Reconstructions and Pre-Flight Predictions for Ascent Flight

The Artemis I launch of the Space Launch System provided the first flight data for the new launch vehicle. The current paper shows comparisons of the preflight force and moment coefficient databases developed using traditional ground test and computation fluid dynamics to post-flight data reconstructions of the ascent aerodynamic force and moment coefficients. The post-flight reconstructions were developed using instrumentation on the vehicle, meteorological data, and Newton’s laws. In general, the preflight databases and post-flight reconstructed data showed similar trends throughout ascent from Mach 0.20 to Mach 3.50. Axial force coefficient showed the largest discrepancies, which is likely due to the difficulty of computing axial force from the flight data.

Space Launch System↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Using Multiplicative Algebraic Reconstruction Techniques (MART) to Derive Instrument Requirements for Computed Tomography Imaging Spectrographs

Computed Tomography Imaging Spectrographs (CTISs), which are generally slitless or large-aperture spectrographs that observe a wide, dispersed field of view in multiple dispersion angles or diffraction orders, provide a unique opportunity to capture spectral information over an extended source, such as the Sun, but require software reconstruction techniques to be fully utilized. A useful data product that can be recovered from CTIS observations is intensity maps of solar features in single spectral lines. These intensity maps can then be used to determine temperature, density, abundance, and equilibrium properties of the emitting plasma. We apply the multiplicative algebraic reconstruction technique (MART) to example data from a variety of CTIS configurations to determine the capability and limitations of the method to return spectrally-pure maps. By completing this study, we aim to establish a path to derive requirements for CTIS instruments that rely on reconstruction techniques to meet their science objectives.

Amy Winebarger↗

NASA NTRSDate not supplied

Evaluation of Artemis I Aerodynamic Force and Moment Reconstructions and Preflight Predictions for Ascent Flight

The Artemis I launch of the Space Launch System provided the first flight data for the new launch vehicle. The current paper shows comparisons of the preflight force and moment coefficient databases developed using traditional ground test and computation fluid dynamics to post-flight data reconstructions of the ascent aerodynamic force and moment coefficients. The post-flight reconstructions were developed using instrumentation on the vehicle, meteorological data, and Newton’s laws. In general, the preflight databases and post-flight reconstructed data showed similar trends throughout ascent from Mach 0.20 to Mach 3.50. Axial force coefficient showed the largest discrepancies, which is likely due to the difficulty of computing axial force from the flight data.

Space Launch System↗

NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D. Karlgaard↗

NASA NTRSDate not supplied

Multiscale Modeling of Reconstructed Tricalcium Silicate using NASA Multiscale Analysis Tool

To study microstructure characteristics of cementitious materials hydrated in space; previously, cement binder formations were processed under microgravity conditions and was further compared against ground-based experiments. For accurate estimation of process-structure-property linkage, particularly on samples hydrated in the microgravity environment, it is desired to have a high-fidelity volumetric representation of the microstructure. However, owing to small sample size and high porosity of the space-returned samples, conventional experimental characterization techniques are not viable. Hence, a deep learning-based reconstruction algorithm was employed to obtain high fidelity 3D volumes from sparse high resolution 2D Scanning Electron Microscopy (SEM) images, as inputs to micromechanics-based modeling. This machine learning-based reconstruction methodology validated against low-order statistical descriptors, captured the microstructural topology of both sample types (ground, 1g and microgravity, μg). Due to the lack of gravity, hydration products of the samples processed in space differed from those processed-on ground. Such AI-generated virtual samples were analyzed in a multiscale recursive micromechanics approach using the NASA Multiscale Analysis Tool (NASMAT). Here, we present a methodology to rapidly integrate and evaluate these AI-generated volumes in NASMAT. The synthesized microstructural volumes are directly employed as Representative Volume Elements (RVEs) to preserve the fidelity (1 pixel = 0.54 m). Invariably, analysis of such largescale problems (5123 voxels) requires huge amount of computational resources. By taking advantage of the NASMAT architecture, we also focused on systematic multiscale integration of these AI-reconstructed virtual volumes to reduce the computational demands. In this work, this methodology is demonstrated on the ground-based, 1g samples. The estimated stiffness value of 15.90 GPa is comparable to experimentally obtained modulus of hydrated tricalcium silicate sample. The workflow presented here paves the way for utilizing the NASMAT tool to perform multiscale analyses of other multi-phase material systems using either 3D virtual datasets synthesized using AI or obtained via micro-CT.

Machine Learning↗

NASA NTRS2023

How do tradeoffs in satellite spatial and temporal resolution impact snow water equivalent reconstruction?

Given the tradeoffs between spatial and temporal resolution, questions about resolution optimality are fundamental to the study of global snow. Answers to these questions will inform future scientific priorities and mission specifications. Heterogeneity of mountain snowpacks drives a need for daily snow cover mapping at the slope scale (≤30 m) that is unmet for a variety of scientific users, ranging from hydrologists to the military to wildlife biologists. But finer spatial resolution usually requires coarser temporal or spectral resolution. Thus, no single sensor can meet all these needs. Recently, constellations of satellites and fusion techniques have made noteworthy progress. The efficacy of two such recent advances is examined: (1) a fused MODIS–Landsat product with daily 30 m spatial resolution and (2) a harmonized Landsat 8 and Sentinel 2A and B (HLS) product with 3–4 d temporal and 30 m spatial resolution. State-of-the-art spectral unmixing techniques are applied to surface reflectance products from 1 and 2 to create snow cover and albedo maps. Then an energy balance model was run to reconstruct snow water equivalent (SWE). For validation, lidar-based Airborne Snow Observatory SWE estimates were used. Results show that reconstructed SWE forced with 30 m resolution snow cover has lower bias, a measure of basin-wide accuracy, than the baseline case using MODIS (463 m cell size) but greater mean absolute error, a measure of per-pixel accuracy. However, the differences in errors may be within uncertainties from scaling artifacts, e.g., basin boundary delineation. Other explanations are (1) the importance of daily acquisitions and (2) the limitations of downscaled forcings for reconstruction. Conclusions are as follows: (1) spectrally unmixed snow cover and snow albedo from MODIS continue to provide accurate forcings for snow models and (2) finer spatial and temporal resolution through sensor design, fusion techniques, and satellite constellations are the future for Earth observations, but existing moderate-resolution sensors still offer value.

Edward H. Bair↗

NASA NTRSDate not supplied

GT2024-128885: Flow Reconstruction in a Transonic Turbine Cascade using Physics-Informed Neural Networks (PINNs)

This presentation investigates the application of Physics-Informed Neural Networks (PINNs) for the analysis of turbine blades in a transonic cascade. PINNs are a machine learning method trained on losses calculated from reconstructed governing equations, assigned boundary/initial conditions, and measured data. We reconstruct the 2-D flow field in a transonic turbine cascade in two ways: the traditional forward approach (without training/experimental data) and by training the PINN using experimental data. We then compare the PINN solutions to measured data. This is repeated for three different turbine blades with distinct loading characteristics. The experimental data used for training is the static pressure measurements along the suction and pressure sides of each blade. The PINN is trained utilizing all available data, half the available data, data from only the leading edge region, and data from only the trailing edge region. It's shown that the PINN can reconstruct the flow field in all cases with acceptable errors. Cases where the PINN is trained on all the data, and even half the data, resulted in the lowest errors. The exit Mach number is inferred for each case and compared to the experimentally calculated value.

Machine Learning↗

NASA NTRSDate not supplied

Direct Reconstruction of Ablative Thermal Protection System Aeroheating Using A Green's Function Approach

A Green’s function inverse heat transfer (IHT) approach is used to reconstruct the surface heating conditions on ablative thermal protection system (TPS) materials from embedded heat flux sensor and temperature probe measurements. The approach models the temperature time-history at the measurement location as a discrete linear system, allowing for the heat flux boundary condition to be recovered directly without the need for time-marching schemes. The effects of material decomposition and pyrolysis gas transport are modeled using an energy source/sink analogue. The performance of the reconstruction approach is analyzed on a 1D test case representative of an atmospheric entry heating scenario. The approach can recover the TPS surface heat flux to within 4% of the input heating condition with a computation time of 2-3 seconds (>3 orders of magnitude faster than current time-marching IHT methods). As a byproduct of the surface heating reconstruction, the algorithm also captures the surface pyrolysis gas mass flux and solid decomposition at multiple through-thickness locations within the TPS.

Kenneth McAfee↗