Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Natural laminar flow and airplane stability and control

Location and mode of transition from laminar to turbulent boundary layer flow have a dominant effect on the aerodynamic characteristics of an airfoil section. The influences of these parameters on the sectional lift and drag characteristics of three airfoils are examined. Both analytical and experimental results demonstrate that when the boundary layer transitions near the leading edge as a result of surface roughness, extensive trailing-edge separation of the turbulent boundary layer may occur. If the airfoil has a relatively sharp leading-edge, leading-edge stall due to laminar separation can occur after the leading-edge suction peak is formed. These two-dimensional results are used to examine the effects of boundary layer transition behavior on airplane longitudinal and lateral-directional stability and control.

Vandam, Cornelis P.↗
NASA NTRS1960

Hydrodynamic and Aerodynamic Characteristics of a Model of a Supersonic Multijet Water-Based Aircraft Equipped with Supercavitating Hydrofoils

The hydrodynamic and aerodynamic characteristics of a model of a multijet water-based Mach 2.0 aircraft equipped with hydrofoils have been determined. Takeoff stability and spray characteristics were very good, and sufficient excess thrust was available for takeoff in approximately 32 seconds and 4,700 feet at a gross weight of 225,000 pounds. Longitudinal and lateral stability during smooth-water landings were good. Lateral stability was good during rough-water landings, but forward location of the hydrofoils or added pitch damping was required to prevent diving. Hydrofoils were found to increase the aerodynamic lift-curve slope and to increase the aerodynamic drag coefficient in the transonic speed range, and the maximum lift-drag ratio decreased from 7.6 to 7.2 at the cruise Mach number of 0.9. The hydrofoils provided an increment of positive pitching moment over the Mach number range of the tests (0.6 to 1.42) and reduced the effective dihedral and directional stability.

McKann, Robert E.↗
NASA NTRS2010

CFD Assessment of Aerodynamic Degradation of a Subsonic Transport Due to Airframe Damage

A computational study is presented to assess the utility of two NASA unstructured Navier-Stokes flow solvers for capturing the degradation in static stability and aerodynamic performance of a NASA General Transport Model (GTM) due to airframe damage. The approach is to correlate computational results with a substantial subset of experimental data for the GTM undergoing progressive losses to the wing, vertical tail, and horizontal tail components. The ultimate goal is to advance the probability of inserting computational data into the creation of advanced flight simulation models of damaged subsonic aircraft in order to improve pilot training. Results presented in this paper demonstrate good correlations with slope-derived quantities, such as pitch static margin and static directional stability, and incremental rolling moment due to wing damage. This study further demonstrates that high fidelity Navier-Stokes flow solvers could augment flight simulation models with additional aerodynamic data for various airframe damage scenarios.

Frink, Neal T.↗
NASA NTRS1959

Effects of Forebody Deflection on the Stability and Control Characteristics of a Canard Airplane Configuration with a High Trapezoidal Wing at a Mach Number of 2.01

An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 to determine the effects of forebody deflection on the stability and control characteristics of a canard airplane configuration. The configuration had a high trapezoidal aspect-ratio-3 wing, a trapezoidal canard surface, and a single swept vertical tail. Forebody deflection angles of 0 deg, 2 deg and deg were investigated. The results indicated that nose-up deflections of the forebody provided positive increments of pitching moment with little increase in drag and hence would be useful in reducing the pitch-control requirements and the attendant losses in lift-drag ratio due to trimming. Deflection of the forebody, however, aggravated the decrease in directional stability with increasing angle of attack by causing a loss in tail contribution and by increasing the instability of the wing-body combination.

Spearman, M. Leroy↗
NASA NTRS1999

Unstructured Grid Euler Method Assessment for Longitudinal and Lateral/Directional Stability Analysis of the HSR Reference H Configuration at Transonic Speeds

Transonic Euler computations, based on unstructured grid methodology, are performed for a proposed High Speed Civil Transport (HSCT) configuration, designated as the Reference H configuration within the High Speed Research (HSR) Program. The predicted results are correlated with appropriate experimental wind-tunnel data for the baseline configuration with and without control surface deflections for a range of angle of attack at M(sub infinity) = 0.95. Good correlations between the predictions and measured data have been obtained for the longitudinal aerodynamic characteristics of the baseline configuration. The incremental effects in the longitudinal aerodynamic characteristics due to horizontal rail deflections as well as wing leading-edge and trailing-edge flap deflections have also been predicted reasonably well. Computational results and correlations with data are also presented for the lateral and directional stability characteristics for a range of angle of attack at a constant sideslip angle as well as a range of sideslip angles at a constant angle of attack. In addition, the results are presented to assess the computational method performance and convergence characteristics.

Ghaffari, Farhad↗
NASA NTRS1970

Effects of Nose Bluntness on Aerodynamic Characteristics of Cruciform-Finned Missile Configuration at Mach 1.50 to 2.86

An investigation has been conducted in the Langley Unitary Plan wind tunnel to determine the effects of spherical nose bluntness on the aerodynamic characteristics of a typical cruciform-finned short-range missile configuration for roll angles of 0 deg and 45 deg and Mach numbers from 1.50 to 2.86. Also investigated was the effectiveness of a forward protruding nose spike in reducing the axial-force coefficient of a blunt-nose configuration. The results indicated that the effects of nose bluntness and nose spike on the longitudinal stability were small. For roll angles of both 0 deg and 45 deg, the greatest effects of nose bluntness on the aerodynamic-center location near zero angle of attack occurred at a Mach number of 2.86, where for each roll position, a rearward shift of approximately 3.5 percent of the body length occurred as bluntness was increased. Although large magnitudes of nose bluntness were accompanied by high axial-force coefficients, significant reductions in the axial-force coefficient of a blunt-nose configuration were achieved with the use of the nose spike. There were no noteworthy effects of nose bluntness on either the directional stability or side-force parameters. However, for high angles of attack at a Mach number of 1.50 increased nose bluntness generally resulted in decreased effective dihedral.

Jernell, L. S.↗
NASA NTRS1955

Lateral Stability and Control Measurements of a 0.0858-Scale Model of the Lockheed XF-104 Airplane at Transonic Speeds

An investigation of the lateral stability and control effectiveness of a 0.0858-scale model of the Lockheed XF-104 airplane has been conducted in the Langley 16-foot transonic tunnel. The model has a low aspect ratio, 3.4-percent-thick wing with negative dihedral. The horizontal tail is located on top of the vertical tail. The investigation was made through a Mach number range of 0.80 to 1.06 at sideslip angles of -5 deg. to 5 deg. and angles of attack from 0 deg. to 16 deg. The control effectiveness of the aileron, rudder, and yaw damper were determined through the Mach number and angle-of-attack range. The results of the investigation indicated that the directional stability derivative was stable and that positive effective dihedral existed throughout the lift-coefficient range and Mach number range tested. The total aileron effectiveness, which in general produced favorable yaw with rolling moment, remained fairly constant for lift coefficients up to about 0.8 for the Mach number range tested. Yawing-moment effectiveness of the rudder changed little through the Mach number range. However, the yaw damper effectiveness decreased about 30 percent at the intermediate test Mach numbers.

Arabian, Donald D.↗
NASA NTRS1977

Augmentation of maneuver performance by spanwise blowing

A generalized wind tunnel model was tested to investigate new component concepts utilizing spanwise blowing to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on high angle of attack performance, stability, and control at subsonic speeds. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex-induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack. Spanwise blowing on the wing reduced horizontal tail loading and improved the lateral-directional stability characteristics of a wing-horizontal tail-vertical tail configuration.

Erickson, G. E.↗
NASA NTRS1997

Evaluation of the Low-Speed Stability and Control Characteristics of a Mach 5.5 Waverider Concept

Static force and moment tests of a 0.062-scale model of a hypersonic vehicle study concept known as the LOFLYTE(TM) configuration were conducted in the Langley 12-Foot Low-Speed Tunnel. These tests looked primarily at the low-speed static stability and control characteristics of this configuration. Data were obtained over an angle-of-attack range of -5 deg. to 22 deg. at sideslip angles that ranged between -10 deg. and 10 deg. The tiperons were sized to provide enough pitch control to trim the vehicle up to alpha = 16 deg. with no more than 10 deg. of surface deflection and data obtained in this test showed that 10 deg. of tiperon deflection was nearly sufficient to trim the configuration up to the desired angle of attack. Because of the pitching-moment characteristics of the LOFLYTE(TM) configuration, there is a reasonably high level of unpowered trimmed lift at nominal takeoff and approach to landing that should allow for acceptable takeoff and landing speeds for this vehicle. Initial evaluation of the directional stability characteristics of this configuration showed a significant instability between alpha = 10 deg. and about alpha = 18 deg. This test determined that the cause of this instability was the interaction of the wing leading-edge vortex with the vertical tails. Moving the vertical tails either inboard or outboard from the baseline location eliminated this unfavorable interaction.

Hahne, David E.↗
NASA NTRS1959

Static Stability Characteristics of Three Thick Wing Models with Parabolic Plan Forms at a Mach Number of 3.11

An experimental investigation has been made to determine the static stability characteristics of three thick wing models with parabolic plan forms at a Mach number of 3.11 for angles of attack from about -6 to 16 deg. The primary variable was aspect ratio, with the plan-form area and the ratio of base height to span kept the same for all three models. All models had stable, linear pitching-moment curves about the quarter chord of the wing mean aerodynamic chord. The model with the lowest aspect ratio attained a maximum untrimmed lift-drag ratio of about 5.0 at an angle of attack of about 8 deg. Increasing the aspect ratio (which was accompanied by an increase in base area because the ratio of the base height to span was kept constant) caused a decrease in maximum lift-drag ratio. All models were directionally stable for the range of angle of attack of the tests. Addition of a vertical tail to the models caused an increase in the directional stability over the angle-of-attack range. In general, the lateral aerodynamic characteristics of the models were not linear functions of angle of attack over any appreciable angle-of-attack range.

Queijo, M. J.↗
NASA NTRS1983

An aerodynamic assessment of various supersonic fighter airplanes based on Soviet design concepts

The aerodynamic, stability, and control characteristics of several supersonic fighter airplane concepts were assessed. The configurations include fixed-wing airplanes having delta wings, swept wings, and trapezoidal wings, and variable wing-sweep airplanes. Each concept employs aft tail controls. The concepts vary from lightweight, single engine, air superiority, point interceptor, or ground attack types to larger twin-engine interceptor and reconnaissance designs. Results indicate that careful application of the transonic or supersonic area rule can provide nearly optimum shaping for minimum drag for a specified Mach number requirement. Through the proper location of components and the exploitation of interference flow fields, the concepts provide linear pitching moment characteristics, high control effectiveness, and reasonably small variations in aerodynamic center location with a resulting high potential for maneuvering capability. By careful attention to component shaping and location and through the exploitation of local flow fields, favorable roll-to-yaw ratios may result and a high degree of directional stability can be achieved.

Spearman, M. L.↗
NASA NTRS1948

Flight Investigation to Determine the Aerodynamic Characteristics of Rocket-Powered Models Representative of a Fighter-Type Airplane Configuration Incorporating an Inverse-Taper Wing and a Vee Tail

Two rocket-powered models representative of a fighter-type airplane were investigated in flight at Mach numbers up to 1.01 and 1.07 by the Langley Pilotless Aircraft Research Division at its testing station at Wallops Island, Va. These models incorporated an inverse-taper wing and a vee tail and were flown with controls undeflected and wing and stabilizer set at 0 deg incidence. Values of lateral acceleration, normal acceleration velocity, and drag were obtained by use of telemeters and a Doppler velocimeter radar unit. The results of this investigation indicated no unusual variation in the lateral acceleration characteristics. After the cessation of powered flight, the lateral oscillation quickly damped to zero. The data indicated that the airplane, at low lift coefficients, should not experience any abrupt trim changes until it attains a Mach number of 0.97. The change in normal-force coefficient associated with this trim change will amount to about 0.03 with the center of gravity located at 4.48% of the mean aerodynamic chord. At higher lift coefficients, on the basis of other data, the Mach number at which this trim change occurs would be expected to be decreased. The neutral point of the model at Mach numbers near 1.05 was estimated to fall at 45% of the mean aerodynamic chord, assuming a lift-curve slope of 0.05. A value of the static-directional-stability parameter dCn/d(psi) of approximately -0.002 was estimated for a Mach number of 0.93. The values of drag coefficient obtained from both model flights were in a good comparative agreement. The highest drag coefficient occurred at a Mach number of 1.01 and was equal to 0.044.

Alexander, Sidney R.↗
NASA NTRS1961

A Wind-Tunnel Investigation of a Transonic-Transport Configuration Utilizing Drag-Reducing Devices at Mach Numbers from 0.20 to 1.03

The static longitudinal stability and control and lateral characteristics of a transonic-transport model, incorporating recent drag-reducing devices, has been investigated in the Langley 8-foot transonic pressure tunnel. The wing was cambered, had a thickened root and a taper ratio of 0.3. Wing sweepback angles of 45 degrees and 40 degrees were investigated with corresponding aspect ratios of 7 and 8, respectively. Modifications to the model for reducing the drag were: a forward fuselage addition and special bodies (four big enough to house jet engines) added to the upper surface of the wing. Other components and changes investigated included an empennage, a wing-tip body, wing fences, wing trailing-edge flaps, horizontal-tail settings, and wing dihedral angle. The investigation covered the Mach number range from 0.20 to 1.03 for the angle-of-attack range from -5 degrees to 15.4 degrees, and a sideslip angle of -5 degrees, in the Reynolds number range from 0.52 times 10(exp 6) to 1.94 times 10(exp 6) based on the wing mean aerodynamic chord. The various fuselage and wing additions delayed the drag-rise Mach number and greatly reduced the drag beyond the drag rise. The wing bodies markedly alleviated unstable pitch tendencies throughout the test Mach number range. At low landing speeds, the wing bodies exhibited little interference with the ability of trailing-edge flaps to increase the lift near maximum lift coefficient; and the use of fences greatly reduced the severe longitudinal instability trend at landing attitudes. The model with a 6 degree dihedral angle exhibited positive lateral and directional stability characteristics in the presence of the fuselage and wing additions. An increase in drag-rise Mach number associated with the fuselage and wing additions on the 40 degree sweptback wing combination was similar to that for the comparable 45 degree combination. These additions did, however, reduce the drag of the 40 degree sweptback configurations more than the 45 degree configurations in the transonic speed range.

Loving, Donald L.↗
NASA NTRS1963

RUNWAY SLIPPERINESS AND SLUSH

Fluid drag, runway slipperiness, and tire hydroplaning results in loss of braking traction, ground directional stability and take-off performance

AIRCRAFT PERFORMANCE↗
NASA NTRS1963

Phenomena of Pneumatic Tire Hydroplaning

Recent research on pneumatic tire hydroplaning has been collected and summarized with the aim of describing what is presently known about the phenomena of tire hydroplaning. A physical description of tire hydroplaning is given along with formulae for estimating the ground speed at which it occurs. Eight manifestations of tire hydroplaning which have been experimentally observed are presented and discussed. These manifestations are: detachment of tire footprint, hydrodynamic ground pressure, spin-down of wheel, suppression of tire bow wave, scouring action of escaping fluid in tire-ground footprint region, peaking of fluid displacement drag, loss in braking traction, and loss of tire directional stability. The vehicle, pavement, tire, and fluid parameters of importance to tire hydroplaning are listed and described. Finally, the hazards of tire hydroplaning to ground and air-vehicle-ground performance are listed, and procedures are given to minimize these effects.

HYDROPLANE↗
NASA NTRS1967

Hypersonic reentry vehicle Patent

Aerodynamic configuration of reentry vehicle heat shield to provide longitudinal and directional stability at hypersonic velocities

Lamb, R. H.↗