Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Stress and strain concentration at a circular hole in an infinite plate

The theory of elasticity shows that the maximum stress at a circular hole in an infinite plate in tension is three times the applied stress when the material remains elastic. The effect of plasticity of the material is to lower this ratio. This paper considers the theoretical problem of the stress distribution in an infinitely large sheet with a circular hole for the general case where the material may have any stress-strain curve. The plate is assumed to be under uniform tension at a large distance from the hole. The material is taken to be isotropic and incompressible. (author)

THEORIES - ELASTICITY↗

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

The three-dimensional grain-averaged response of solid bar samples under non-proportional (NP) elastoplastic axial-torsional loading was investigated using in situ high energy diffraction microscopy (HEDM) and companion crystal plasticity finite element (CPFE) modeling. Important stress metrics including applied shear (σ θZ ) and axial (σ ZZ ) stress tensor components, stress and stress deviator tensor invariants (I 1 , J 2 , and J 3 ), von Mises equivalent stress (σ$^{grain}_{VM}$), maximum resolved shear stress (mRSS), stress triaxiality (η), and lode angle parameter ($\barθ$) values were tracked for ~300 grains under two different loading conditions: (1) Torsion-dominated loading (low NP) and (2) Tension-torsion loading (high NP) in equiatomic NiCoCr, a representative multicomponent face-centered cubic (FCC) superalloy. Overall, significant stress localizations existed within both samples as evidenced by the radial dependence of grain-resolved σ θZ , σ$^{grain}_{VM}$, and J 2 ; by comparison, I 1 , J 3 , η, and $\barθ$ metrics did not show discernible trends within the volume. These stress localizations reveal a complex interplay between axial and shear stress components (e.g., stress coupling) resulting in grain yielding near the sample surface largely driven by shear stress, whereas internal grain yielding was largely accommodated by axial stress. Grain-resolved stress localization trends were described well by the CPFE model, although some discrepancies in magnitude occurred, particularly for volumetric stress metrics (I 1 and η) due to initial type II residual stress distributions. The superposition of initial residual stress states onto CPFE grain-resolved data significantly improved model accuracy for η. This suggests that residual stresses more strongly influence the simulation of volumetric rather than deviatoric (yield) stress metrics.

36 MATERIALS SCIENCE↗

A cracked sheet stiffened by several partially debonded intact or broken stringers

The effect of several stringers on the stress intensity factors at the tips of a crack is considered. The stringers which were continuously attached to the plate and placed perpendicular to the crack may be partially debonded due to high stress concentrations. Since the stringers may even break under excessive loading conditions, both intact and broken stringers are considered to investigate the effect of rupture. The continuity of displacements along the bond lines leads to an integral equation which is solved to give the shear stress distribution in the adhesive and the stress intensity factors at the crack tips.

Arin, K.↗

The effect of several intact or broken stringers of the stress intensity factor in a cracked sheet

The stringers which are continuously attached to the plate and placed perpendicular to the crack may be partially debonded due to high stress concentrations. Since the stringers may even break under excessive loading conditions, both intact and broken stringers are considered to investigate the effect of rupture. The continuity of displacements along the bond lines leads to an integral equation which is solved to give the shear stress distribution in the adhesive and the stress intensity factors at the crack tips.

Arin, K.↗

Computational Modeling of Graphite Degradation due to Molten Salt Infiltration and Wear

Molten-salt reactors (MSRs) represent a promising next-generation reactor design, with graphite serving as a moderator and/or reflector in several designs. However, due to limited experimental data and operational experience, a technical understanding of the structural integrity of graphite in molten salt environments remains incomplete. This report presents a modeling-based evaluation of graphite degradation in MSR environments, focusing on the effects of salt infiltration in fuel salt-based designs and surface wear in pebble bed reactor designs. The objective of this study is to enhance understanding of the structural integrity challenges posed by these degradation mechanisms and to provide a framework for assessing graphite behavior in MSRs. The first part of the report investigates the phenomenon of molten salt infiltration into graphite. This infiltration occurs when molten salt permeates the interconnected pore structure of the graphite moderator, driven by factors such as pressure differentials and the physical properties of both the salt and graphite. The infiltration process is influenced by characteristics of the pore structure, viscosity of the molten salt, and the interfacial energies between the graphite, salt, and the atmosphere within the graphite pore. Utilizing a coupled multiphysics modeling approach with Grizzly software, the study evaluates the stress induced by internal heat sources due to infiltration, which can lead to structural concerns. This evaluation is crucial for understanding how infiltration affects the mechanical integrity of graphite components in MSRs. The study considers the Molten-Salt Reactor Experiment (MSRE) graphite stringer geometry due to the availability of relevant data. Through detailed finite element analysis, the study examines stress distributions at varying infiltration percentages, revealing that stress levels increase with higher amounts of infiltration. Rare-event simulations, using the parallel subset simulation (PSS) framework, further quantify the failure probabilities under input uncertainties, with a user-specified failure metric. The PSS framework also identifies critical input parameters that significantly affect the stress values, including infiltration amount, thermal conductivity, and power density. Additionally, considering realistic reactor scenarios, the analysis was performed to account for the combined effects of radiation and infiltration, and modeling strategies on how to analyze new reactor designs or new graphite grades are discussed. The second part of the report focuses on wear mechanisms in pebble bed-based MSRs. As graphite fuel pebbles interact with the graphite reflector block, wear can result in material loss and the formation of surface defects, which may act as stress concentrators. A similar multiphysics modeling framework is employed to assess the impact of wear on the structural integrity of graphite components. This study considers a generic fluoride-cooled high-temperature reactor (gFHR) design due to the availability of comprehensive data. Worst-case scenario dimensions of the reflector blocks were analyzed under thermal and radiation conditions. Subsequently, wear in the form of idealized pits and grooves is modeled on the inner surface of the graphite block, with the maximum stress from previous simulations. The simulations show that groove-type defects are more detrimental than pits, leading to higher stress concentrations. Considering worst-case simulation scenarios and experimental wear rates, it was determined that the formation of a surface defect critical enough to affect the stress may not be possible in a gFHR design. Overall, the findings of this research contribute to the development of robust modeling tools for predicting graphite behavior under various operational conditions in MSRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗

A cracked orthotropic sheet stiffened by a semi-infinite orthotropic sheet

The stress intensity factor is determined for a cracked orthotropic sheet adhesively bonded to an orthotropic stringer. Since the stringer is modeled as a semiinfinite sheet, the solution is most appropriate for a crack tip located near a stringer edge. Both adherends are treated as homogeneous, orthotropic media. It is assumed they are in plane stress and the adhesive is in pure shear. From Green's functions and the complex variable theory of orthotropic elasticity developed by Lekhnitskiy, a set of integral equations is obtained. The integral equations are replaced by an equivalent set of algebraic equations which is solved to obtain the shear stress distribution in the adhesive layer. With these stresses, equations for the stress intensity factors at both crack tips are found. A parametric study is conducted to determine the sensitivity of the system to material properties and specimen configuration. Unless the crack tip is very close to or under the stringer the stress intensity factor is approximately that of an unstiffened sheet. However, as the crack propagates beneath the stringer, the stress intensity factor decreases significantly. Increasing the stiffness of the stringer or the adhesive also results in a decrease in the stress intensity factor.

Bigelow, C. A.↗

Improvement of Reynolds-Stress and Triple-Product Lag Models

The Reynolds-stress and triple product Lag models were created with a normal stress distribution which was defined by the accepted 4:3:2 distribution of streamwise, spanwise and wall normal stresses, and a ratio of τ(sub w) = 0.3k in the log layer region of high Reynolds number flat plate flow, which implies R11(+) = 4/(9/2)∗.3 ≈ 2.96. More recent measurements show a more complex picture of the log layer region at high Reynolds numbers. The first cut at improving these models along with the direction for future refinements is described. Comparison with recent high Reynolds number data shows areas where further work is needed, but also shows inclusion of the modeled turbulent transport terms improve the prediction where they influence the solution. Additional work is needed to develop a model that better matches experiments, but there is significant improvement in many of the details of the log layer behavior.

Fluid dynamics↗

Improvement of Reynolds-Stress and Triple-Product Lag Models

The Reynolds-stress and triple product Lag models were created with a normal stress distribution which was defined by the accepted 4:3:2 distribution of streamwise, spanwise and wall normal stresses, and a ratio of τ(sub w) = 0.3k in the log layer region of high Reynolds number flat plate flow, which implies R11(+) = 4/(9/2)∗.3 ≈ 2.96. More recent measurements show a more complex picture of the log layer region at high Reynolds numbers. The first cut at improving these models along with the direction for future refinements is described. Comparison with recent high Reynolds number data shows areas where further work is needed, but also shows inclusion of the modeled turbulent transport terms improve the prediction where they influence the solution. Additional work is needed to develop a model that better matches experiments, but there is significant improvement in many of the details of the log layer behavior.

Turbulence↗

Plume-Surface Interaction Modeling for a Human-Scale Mars Lander

Landing vehicles impart thermal and strain energy onto the landing site from the retrorocket exhaust. Depending on the design of the vehicle, the energy may be great enough to cause spallation at the landing site. This damage may be minor and repairable in the case of landing on a terrestrial landing pad. For missions to other planetary bodies, the spallation may cause the landing site to become uneven and unstable, as well as damage. Simulating this phenomenon in a laboratory or computationally would require a significant amount of time and other resources. These resources typically are not available during the design phase of a mission. This paper presents a computationally-efficient model for the temperature and stress distributions that arise during landing. These quantities can be used along with existing failure criteria, such as the Hoek-Brown criterion for geological materials, to quickly determine whether spallation will occur. The stress and temperature distributions at the landing site are inherently 3D; however, there is a plane of symmetry and in that plane the distributions are 2D. Both quantities are modeled using series solutions to their governing partial differential equations (PDEs). The stress is modeled using the Airy stress potential function and its governing PDE is the biharmonic equation. The temperature is governed by Fourier's law. The models assume that stress due to gravity can be neglected, the points in the plane do not accelerate, and that the material properties are constant.

Hart, Kenneth↗

Interfacial Strength Evaluation of Oxide Films on Carbon Steel by Using the Laser Shock Adhesion Test

We investigate the adhesion strength (interfacial strength) of the oxide film formed on a carbon steel substrate by using a laser shock adhesion test (LaSAT). A rolled carbon steel (SS400) plate is first heated at high temperature (700 °C) under the atmosphere (heat treatment) to cause the formation of oxide films about 20-50 μm thick on the steel surface. The film consisted of multiple layers, including wustite (FeO), magnetite (Fe{sub 3}O{sub 4}), and hematite (Fe{sub 2}O{sub 3}). Next, the x-ray diffraction method was used to measure the residual stress in the film. We find that compression stress develops in the film because of a mismatch of thermal strain in between the film and substrate after the heat treatment. With LaSAT, strong elastic wave generates by a pulsed laser ablation of the substrate backside, and results in interfacial fractures in the oxide films. To monitor the normal (out-of-plane) displacement of the top surface film, a laser ultrasonic interferometer is simultaneously utilized, such that we detect film delamination and determine the critical laser energy for interfacial fracture to obtain the critical stress (interfacial strength). Furthermore, additional pulsed laser irradiation is conducted against a pre-delaminated specimen in order to examine the growth of delamination area and evaluate the interfacial fracture toughness. Finally, elastic wave propagation in the sample is computed using the finite element method (FEM) in order to evaluate the interfacial stress field, accurately. For the FEM, multiple layers in the oxide film are modeled, and the residual stress due to thermal strain mismatch is introduced. The FEM computations reveal the stress distribution around the interface and evaluate the critical stress and critical stress intensity factor for delamination. We thus quantitatively evaluate the interfacial strength and interfacial fracture toughness of the oxide film formed on carbon steel. The mechanism of interfacial fracture is also discussed on the basis of microstructures in a film with multiple layers. This result may be useful for understanding the adhesion quality of oxide film during the hot-rolling process.

36 MATERIALS SCIENCE↗

Computational modeling of graphite degradation in molten salt reactors: Role of infiltration

Molten salt reactors (MSRs) often employ graphite as a moderator and reflector. An important challenge for deploying graphite in these reactors is that, due to limited experimental data, our understanding of graphite’s structural integrity in molten salt environments remains incomplete. Here, this study addresses heat generation from fuel-bearing salt that has infiltrated open pores in the graphite, driven primarily by pressure differentials. This is one of multiple identified physical and chemical mechanisms through which molten salt could potentially degrade graphite. Thermally driven stresses are quantified using the Molten-Salt Reactor Experiment (MSRE) graphite moderator elements as a case study. Finite element simulations predict stress distributions at varying infiltration levels, indicating that thermal stresses increase with higher infiltration. Rare-event simulations using the parallel subset simulation framework identify the combinations and corresponding ranges of input parameters that lead to stresses above a specified threshold. In particular, combinations involving high infiltration amounts, high power density, and low thermal conductivity tend to induce the highest stresses. Under the inputs and assumptions considered in this work, the magnitudes of the thermally driven stresses are quite low, with a very low likelihood of causing failure due to exceeding the graphite’s tensile strength. Additionally, rare-event simulations were performed for two more scenarios: a scaled-up moderator geometry and a localized hotspot in the original geometry. Both cases resulted in increased susceptibility to failure, though not to a detrimental extent. Furthermore, the combined effects of irradiation and infiltration-induced thermal stresses were evaluated. The results showed that thermal stresses from infiltration were negligible compared to those caused by irradiation. The findings of such a study are inherently component-specific, but the methodology presented here could be used for similar assessments of salt-infiltration effects in other graphite components.

36 - MATERIALS SCIENCE↗

Acute Stent-Induced Endothelial Denudation: Biomechanical Predictors of Vascular Injury

Recent concern for local drug delivery and withdrawal of the first Food and Drug Administration-approved bioresorbable scaffold emphasizes the need to optimize the relationships between stent design and drug release with imposed arterial injury and observed pharmacodynamics. In this study, we examine the hypothesis that vascular injury is predictable from stent design and that the expanding force of stent deployment results in increased circumferential stress in the arterial tissue, which may explain acute injury poststent deployment. Using both numerical simulations and ex vivo experiments on three different stent designs (slotted tube, corrugated ring, and delta wing), arterial injury due to device deployment was examined. Furthermore, using numerical simulations, the consequence of changing stent strut radial thickness on arterial wall shear stress and arterial circumferential stress distributions was examined. Regions with predicted arterial circumferential stress exceeding a threshold of 49.5 kPa compared favorably with observed ex vivo endothelial denudation for the three considered stent designs. In addition, increasing strut thickness was predicted to result in more areas of denudation and larger areas exposed to low wall shear stress. We conclude that the acute arterial injury, observed immediately following stent expansion, is caused by high circumferential hoop stresses in the interstrut region, and denuded area profiles are dependent on unit cell geometric features. Such findings when coupled with where drugs move might explain the drug–device interactions.

Conway, Claire↗