SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Stress analysis of adhesive bonded stiffener plates and double joints

The general problem of adhesive bonded stiffener plates and double joints of dissimilar orthotropic adherends with transverse shear deformations are analyzed. Adhesive layers are assumed to be of an isotropic, elastic and relatively flexible material. It is shown that the stress distributions in the adhesive layers are very much dependent on the bending deformations in adherends. Also, it is found that, in the adhesive layer, maximum transverse normal stress is, in many cases, larger than the longitudinal shear stress and that both occur at the edge of the joint. The general method of solution developed is applied to several practical examples.

Yuceoglu, U.↗

NASA NTRS1979

Experimental and analytical study of fatigue damage in notched graphite/epoxy laminates

Both tension and compression fatigue behaviors were investigated in four notched graphite/epoxy laminates. After fatigue loading, specimens were examined for damage type and location using visual inspection, light microscopy, scanning electron microscopy, ultrasonic C-scans, and X-radiography. Delamination and ply cracking were found to be the dominant types of fatigue damage. In general, ply cracks did not propagate into adjacent plies of differing fiber orientation. To help understand the varied fatigue observations, the interlaminar stress distribution was calculated with finite element analysis for the regions around the hole and along the straight free edge. Comparison of observed delamination locations with the calculated stresses indicated that both interlaminar shear and peel stresses must be considered when predicting delamination. The effects of the fatigue cycling on residual strength and stiffness were measured for some specimens of each laminate type. Fatigue loading generally caused only small stiffness losses. In all cases, residual strengths were greater than or equal to the virgin strengths.

Whitcomb, J. D.↗

NASA NTRS1990

Mechanical behaviors of ceramic matrix composites with matrix cracking and fiber debonding

The purpose of this paper is to summarize the current research of the authors on the mechanical behaviors of ceramic matrix composites, including (1) the stress distributions in a composite with matrix cracking and interfacial debonding, (2) the critical strain for matrix cracking, and (3) the effects of fiber/matrix debonding and thermal residual stresses on the critical strain. The stress fields in both bonded and debonded regions are evaluated by taking into account thermal effects. An energy balance approach is followed to determine the critical strain for matrix cracking. From the general equation of the critical strain for matrix cracking, close form solutions have been obtained for two limiting cases: perfect bonding and complete debonding. Numerical solutions are given for the cases of partial fiber debonding and nonzero debonding energy. It is found that thermal residual stresses and the debonding energy have significant effects on the critical strain.

Kuo, Wen-Shyong↗

NASA NTRS1991

Creep and stress relaxation modeling of polycrystalline ceramic fibers

A variety of high performance polycrystalline ceramic fibers are currently being considered as reinforcement for high temperature ceramic matrix composites. However, under mechanical loading above 800 C, these fibers display creep-related instabilities which can result in detrimental changes in composite dimensions, strength, and internal stress distributions. As a first step toward understanding these effects, this study examines the validity of mechanistic-based empirical model which describes primary stage tensile creep and stress relaxation of polycrystalline ceramic fibers as independent functions of time, temperature, and applied stress or strain. To verify these functional dependencies, a simple bend test is used to measure stress relaxation for four types of commercial ceramic fibers for which direct tensile creep data are available. These fibers include both nonoxide (SCS-6, Nicalon) and oxide (PRD-166, FP) compositions. The results of the bend stress relaxation (BSR) test not only confirm the stress, time, and temperature dependencies predicted by the model but also allow measurement of model empirical parameters for the four fiber types. In addition, comparison of model predictions and BSR test results with the literature tensile creep data show good agreement, supporting both the predictive capability of the model and the use of the BSR test as a simple method for parameter determination for other fibers.

Dicarlo, James A.↗

NASA NTRS1992

Effect of contact stresses in four-point bend testing of graphite/epoxy and graphite/PMR-15 composite beams

The results of in-plane four-point bend experiments on unidirectionally reinforced composite beams are presented for graphite/epoxy (T300/934) and graphite/polyimide (G30-500/PMR-15) composites. The maximum load and the location of cracks formed during failure were measured for testpieces with fibers oriented at various angles to the beam axis. Since most of the beams failed near one or more of the load points, the strength of the beams was evaluated in terms of a proposed model for the local stress distribution. In this model, an exact solution to the problem of a localized contact force acting on a unidirectionally reinforced half plane is used to describe the local stress field. The stress singularity at the load points is treated in a manner similar to the stress singularity at a crack tip in fracture mechanisms problems. Using this approach, the effect of fiber angle and elastic material properties on the strength of the beam is described in terms of a load intensity factor. For fiber angles less than 45 deg from the beam axis, a single crack is initiated near one of the load points at a critical value of the load intensity factor. The critical load intensity factor decreases with increasing fiber angle. For larger fiber angles, multiple cracks occur at locations both near and away from the load points, and the load intensity factor at failure increases sharply with increasing fiber angle.

Binienda, W. K.↗

NASA NTRS1992

The effect of contact stresses in four-point bend testing of graphite/epoxy and graphite/PMR-15 composite beams

The results of in-plane four-point bend experiments on unidirectionally reinforced composite beams are presented for graphite/epoxy (T300/934) and graphite/polyimide (G30-500/PMR-15) composites. The maximum load and the location of cracks formed during failure were measured for testpieces with fibers oriented at various angles to the beam axis. Since most of the beams failed near one or more of the load points, the strength of the beams was evaluated in terms of a proposed model, for the local stress distribution. In this model, an exact solution to the problem of a localized contact force acting on a unidirectionally reinforced half plane is used to describe the local stress field. The stress singularity at the load points is treated in a manner similar to the stress singularity at a crack tip in fracture mechanisms problems. Using this approach, the effect of fiber angle and elastic material properties on the strength of the beam is described in terms of a load intensity factor. For fiber angles less than 45 deg from the beam axis, a single crack is initiated near one of the load points at a critical value of the load intensity factor. The critical load intensity factor decreases with the increasing fiber angle. For larger fiber angles, multiple cracks occur at locations both near and away from the load points, and the load intensity factor at failure increases sharply with increasing fiber angle.

Binienda, Wieslaw K.↗

NASA NTRS1994

Creep and stress relaxation modeling of polycrystalline ceramic fibers

A variety of high performance polycrystalline ceramic fibers are currently being considered as reinforcement for high temperature ceramic matrix composites. However, under mechanical loading about 800 C, these fibers display creep related instabilities which can result in detrimental changes in composite dimensions, strength, and internal stress distributions. As a first step toward understanding these effects, this study examines the validity of a mechanism-based empirical model which describes primary stage tensile creep and stress relaxation of polycrystalline ceramic fibers as independent functions of time, temperature, and applied stress or strain. To verify these functional dependencies, a simple bend test is used to measure stress relaxation for four types of commercial ceramic fibers for which direct tensile creep data are available. These fibers include both nonoxide (SCS-6, Nicalon) and oxide (PRD-166, FP) compositions. The results of the Bend Stress Relaxation (BSR) test not only confirm the stress, time, and temperature dependencies predicted by the model, but also allow measurement of model empirical parameters for the four fiber types. In addition, comparison of model tensile creep predictions based on the BSR test results with the literature data show good agreement, supporting both the predictive capability of the model and the use of the BSR text as a simple method for parameter determination for other fibers.

Dicarlo, James A.↗

NASA NTRS1993

An approximate solution for interlaminar stresses in composite laminates

An efficient approximate solution for interlaminar stresses in finite width, symmetric and unsymmetric laminated composites subjected to axial and/or bending loads is presented. The solution is based upon statically admissible stress fields which take into consideration local property mismatch effects and global equilibrium requirements. Unknown constants in the assumed stress states are determined through minimization of the laminate complementary energy. Typical results are presented for through-thickness and interlaminar stress distributions for angle-ply and cross-ply laminates subjected to axial loading. It is shown that the present formulation represents an improved, efficient approximate solution for interlaminar stresses.

Rose, Cheryl A.↗

NASA NTRS1975

The effect of bending on the stresses in adhesive joints

The problem of stress distribution in adhesive joints where two orthotropic plates are bonded through a flexible adhesive layer is analyzed. It is shown that the effect of bending of the adherends on the stresses in the adhesive layer is very significant. The transverse shear deformations of the adherends appear to have little influence on the adhesive layer stresses. The maximum transverse normal stress in the adhesive is shown to be larger than the maximum longitudinal shear stress. The method of solution is applied to several examples of specific joint geometries and material combinations, and is proven to be applicable to other related problems.

Yuceoglu, U.↗

NASA NTRS1980

Viscoelastic analysis of adhesively bonded joints

An adhesively bonded lap joint is analyzed by assuming that the adherends are elastic and the adhesive is linearly viscoelastic. After formulating the general problem a specific example for two identical adherends bonded through a three parameter viscoelastic solid adhesive is considered. The standard Laplace transform technique is used to solve the problem. The stress distribution in the adhesive layer is calculated for three different external loads, namely, membrane loading, bending, and transverse shear loading. The results indicate that the peak value of the normal stress in the adhesive is not only consistently higher than the corresponding shear stress but also decays slower.

Delale, F.↗

NASA NTRS1981

Viscoelastic analysis of adhesively bonded joints

In this paper an adhesively bonded lap joint is analyzed by assuming that the adherends are elastic and the adhesive is linearly viscoelastic. After formulating the general problem a specific example for two identical adherends bonded through a three parameter viscoelastic solid adhesive is considered. The standard Laplace transform technique is used to solve the problem. The stress distribution in the adhesive layer is calculated for three different external loads namely, membrane loading, bending, and transverse shear loading. The results indicate that the peak value of the normal stress in the adhesive is not only consistently higher than the corresponding shear stress but also decays slower.

Delale, F.↗

NASA NTRS1983

Analysis of a thin-walled pressurized torus in contact with a plane

Finite element analysis is applied to study the large deflection of a standing torus loaded by a plane. The internally pressurized thin-walled structure is found to have an elliptical footprint area. Considerable bulge occurs in the sidewall in the region of the load plane. Stress distributions throughout the torus are shown for various load levels and for various modeling strategies at a given load level. In large load ranges finite element calculations show compressive circumferential stress and negative curvature in the footprint region. Results are compared with inelastic wall analysis.

Mack, M. J., Jr.↗

NASA NTRS1989

Thermoplastic matrix composites - Finite-element analysis of mode I and mode II failure specimens

A finite-element analysis was conducted to evaluate the stress distributions within mode I and mode II failure specimens, assuming both isotropic and orthotropic elastic material properties. The effects of anisotropy on both the magnitude and the location of the highest stress concentration at the vicinity of the crack tip are significant. The results from modeling realistic blunt crack tip geometry and resin-rich zones imply that local variations in the microstructure strongly influence the stress state near the crack tip and therefore the measured fracture properties. In addition, the features of a viscoelastic model for thermoplastic matrices are described. This model will be used in future investigations of matrix-dominated failure phenomena.

Bankert, Ray J.↗

NASA NTRS1981

Use of two-dimensional transmission photoelastic models to study stresses in double-lap bolted joints

The stress distribution in two hole connectors in a double lap joint configuration was studied. The following steps are described: (1) fabrication of photoelastic models of double lap double hole joints designed to determine the stresses in the inner lap; (2) assessment of the effects of joint geometry on the stresses in the inner lap; and (3) quantification of differences in the stresses near the two holes. The two holes were on the centerline of the joint and the joints were loaded in tension, parallel to the centerline. Acrylic slip fit pins through the holes served as fasteners. Two dimensional transmission photoelastic models were fabricated by using transparent acrylic outer laps and a photoelastic model material for the inner laps. It is concluded that the photoelastic fringe patterns which are visible when the models are loaded are due almost entirely to stresses in the inner lap.

Hyer, M. W.↗

NASA NTRS1974

Calculation of turbulent shear stress in supersonic boundary layer flows

Turbulent shear stress distributions for supersonic boundary layer flows have been computed from experimental mean boundary layer data. The computations have been made by numerically integrating the time averaged continuity and streamwise momentum equations. Distributions have been obtained for flows upstream and downstream of shock-wave-boundary layer interactions and for both two-dimensional and axisymmetric flows. The computed results are compared with recently reported shear stress measurements which were obtained by hot wire anemometer and laser velocimeter techniques.

Sun, C. C.↗

NASA NTRS1989

Nonlinear response of a blade-stiffened graphite-epoxy panel with a discontinuous stiffener: Work in progress

The problem of calculating detailed stress distributions around discontinuities in buckled, composite structural components for use with the various analytical failure prediction techniques has not been thoroughly explored. The purpose here is the application of computational methods to the detailed stress analysis problem which is the focus of this session of the workshop. One approach to uncovering the difficulties of this type of analysis and to providing specific directions for future research in this area is a direct attack on the problem using currently available analysis tools. A candidate problem has been selected and experiences from calculating its structural response are described.

Knight, Norman F., Jr.↗

NASA NTRS1989

Shear buckling of specially orthotropic plates with centrally located cutouts

The shear loading of a composite rectangular plate with a centrally located circular cutout was analyzed in order to predict the buckling load of the plate. The first step in this analysis is to calculare the in-plane stress distribution of the plate prior to buckling. This problem can be solved using finite element methods, but a quicker and more cost efficient method is desired. The method chosen to determine the pre-buckling stresses is that of boundary collocation using complex variables. The real valued force functions are written in terms of two complex valued functions, each of which is a function of a different complex variable. The solution of the generalized biharmonic function is a superposition of functions of these two complex variables. For this analysis, the force functions are represented with a Laurent series. The constants in these series are found using boundary collocation. Two force equations for complex variables are satisfied over the plate boundaries to obtain these constants. The stresses in the plate are then known for any particular locations on the plate given the applied shear on the edges of the plate.

Klang, Eric C.↗

NASA NTRS1992

Tension fracture of laminates for transport fuselage. Part 1: Material screening

Transport fuselage structures are designed to contain pressure following a large penetrating damage event. Application of composites to fuselage structures requires a data base and supporting analysis on tension damage tolerance. Tests with 430 fracture specimens were used to accomplish the following: (1) identify critical material and laminate variables affecting notch sensitivity, (2) evaluate composite failure criteria, and (3) recommend a screening test method. Variables studied included fiber type, matrix toughness, lamination manufacturing process, and intraply hybridization. The laminates found to have the lowest notch sensitivity were manufactured using automated tow placement. This suggests a possible relationship between the stress distribution and repeatable levels of material inhomogeneity that are larger than found in traditional tape laminates. Laminates with the highest notch sensitivity consisted of toughened matrix materials that were resistant to a splitting phenomena that reduces stress concentrations in load bearing plies. Parameters for conventional fracture criteria were found to increase with the crack length of the smallest notch sizes studied. Most materials and laminate combinations followed less than a square root singularity for the largest crack sizes studied. Specimen geometry, notch type, and notch size were evaluated in developing a screening test procedure. Results indicate that a range of notch sizes must be tested to determine notch sensitivity.

Walker, T. H.↗