Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Probing the elastic modulus and hardness of superionic boron cluster solid electrolytes

Polyhedral borane salts are highly tunable compounds with the potential to be used as solid electrolytes due to their high Li and Na superionic conductivity and relatively wide electrochemical stability window. In considering their application to all solid-state batteries, their mechanical properties play a critical role in their operation due to stresses the solid electrolyte is subjected to during battery operation. Density functional theory (DFT) calculations have provided an initial assessment of bulk and elastic moduli for some selected boron cluster solid electrolytes, but direct measurements are still scarce. Here, in this paper, we report the elastic moduli and hardnesses of LiCB 11 H 12 , LiCB 9 H 10 , NaCB 11 H 12 , and NaCB 9 H 10 for the first time using nanoindentation continuous stiffness method (CSM) measurements under inert atmosphere. Experimental modulus values ranging 8.8–12.3 GPa and hardness values ranging 0.15–0.38 GPa are lower than that of other inorganic solid-state electrolytes such as oxide- and sulfide-based solid electrolytes. DFT calculations on the expected moduli of these compounds are also presented and discussed. Analysis of the indentation plasticity index reveals that these compounds have higher plasticity index compared to other common oxide and sulfide solid electrolytes. According to the calculated Pugh's ratio, all compounds in this study except LiCB 11 H 12 are considered ductile.

25 ENERGY STORAGE↗
DOE OSTI2025

CALPHAD-based ICME design of single-step aging to enhance mechanical strength of WAAM Haynes 282

To match the strength of wire-arc additive manufactured Haynes 282 to its wrought counterpart via a single-step aging heat treatment, the CALPHAD (Calculation of Phase Diagrams) method is integrated with physics-based process-structure-property models and experimental validation. The integrated computational materials engineering (ICME) framework simulates the effects of aging on γ′ and M 23 C 6 precipitation and the resulting yield strength. To improve simulation reliability, the interfacial energies between γ/γ′ and γ/M 23 C 6 carbides were estimated by comparison with precipitation kinetic modeling and measured precipitate sizes. γ′ and M23C6 were found to precipitate simultaneously between 640 and 860 °C, producing microstructures similar to those produced by two-step aging. The optimal γ′ size for peak yield stress was calculated to be 20–23 nm. WAAM Haynes 282 aged at 780 °C for 50 h exceeded the mechanical performance of its wrought counterpart subjected to two-step aging, though desired properties can also be achieved at 800 °C for 16 h or less. The error in yield strength is less than 20 MPa, demonstrating good agreement between the modeling framework and experiments. Creep studies showed that WAAM Haynes 282 exceeded the calculated rupture time, reaching 481 h. This proposed methodology can accelerate the design of aging heat treatments for any γ′-strengthened nickel-base alloy, minimizing the resources required for trial-and-error experiments.

CALPHAD↗
DOE OSTI2025

Strain-Based Assessment of Shale Caprock during Cyclic Underground Hydrogen Storage

Successful large-scale underground hydrogen storage (UHS) in depleted gas reservoirs depends on the integrity of the overlying caprock to prevent hydrogen loss during cyclic injection and depletion. Prior studies on crushed Marcellus shale, a potential caprock, indicate that cyclic hydrogen injection and depletion induces microstructural changes, increasing porosity and permeability. However, the extent of these changes in intact shale remains unclear. This study presents a strain-based experimental approach to quantify volumetric strain evolution in intact Marcellus shale matrix under unconstrained stress conditions. A quadrant-shaped shale sample without visible fractures underwent eight hydrostatic pore-pressure cycles (injection to 1500 psi and depletion to 500 psi in 250 psi steps). Linear strain gauges measured strain in three orthogonal directions. Results indicate progressive plastic strain accumulation, leading to an ∼12% increase in matrix porosity after eight cycles, with an estimated 19% increase after 30 cycles. This porosity increase follows a logarithmic trend, suggesting a diminishing effect in later cycles. Additionally, permeability and diffusive mass flux are projected to rise by ∼70% over 30 cycles, enhancing hydrogen migration risk. The shale matrix also exhibited mechanical stiffening over successive cycles, limiting large-scale deformation but not preventing porosity enhancement. A new parameter, α, was introduced to characterize shale sensitivity to cyclic loading, aiding UHS caprock assessments. These findings underscore the necessity of incorporating cyclic loading effects in UHS site selection and operational strategies to ensure long-term storage integrity.

08 HYDROGEN↗
DOE OSTI2025

Evaluating indoor thermal resilience of passive and low-power cooling shelters for outdoor workers in India

India’s 231 million outdoor workers are exposed to deadly heat during heat waves. We report results from a simulation-based study that focuses on passive design of cooling shelters for the hot and dry climate zone of India. The goal is to design a cooler-than-outdoor shelter for outdoor workers’ intermittent rest and recovery from heat stress during their arduous outdoor work, to avoid heat-related morbidities and mortality. Expected indoor thermal conditions in low-cost cooling shelters deploying a range of passive designs and low-power active measures are investigated, consistent with the current Indian standards and practices, located in the city of Jodhpur in western India. Heat resilience of the shelter was measured with the predicted reduction of hazardous hours inside the shelter based on the wet-bulb globe temperature (WBGT) and extended heat index. These measures include improving the building envelope, installing cool roofs, using internal thermal mass, and natural ventilation. Additionally, a low-power active measure of using ventilation fans and ceiling fans is explored. EnergyPlus-based simulation results show that simple, commonly available measures, particularly natural ventilation and ceiling fans, achieve the most significant reductions in overheating danger hours, by 22% and 21%, respectively, while more complex or costly passive strategies yield only marginal additional benefits. Moreover, combined measure packages are identified that can reduce the indoor WBGT by 8 to 10 °C, eliminating overheating danger hours. These findings highlight the critical importance of scalable, low-cost, and easily deployable cooling solutions for developing resilient cooling shelters for vulnerable outdoor workers during heat waves in India.

building performance↗
DOE OSTI2025

Observation of Electromagnetic Transients in a Nb3Sn 4-layer Dipole Mirror Magnet

During testing of the Stress Managed Cosine-Theta dipole mirror magnet SMCTM1, magnet quenches were observed following large voltage spikes in the half-coil voltage taps which preceded normal quench initiation. Following some recent work at CERN measuring power current converter transients in relation to flux jumps, an additional differential current probe was added to the magnet instrumentation. Measurements of this probe, as well as the half coil voltage taps show a fast and substantial current change preceding the quench, hinting at coil motion. A simple model based on relative shift of the inner and outer layer coils was developed which suggests the magnitude of coil shift events is on the estimated relative coil shift from the magnet constraint conditions. The behavior is shown to be reversible and characteristic of stick-slip.

Krave, Steven [Fermilab] (ORCID:0000000217521457)↗
DOE OSTI2025

Birefringence axis rotation and nonlinear response of a side-hole fiber pressure sensor

The pressure-induced birefringence of side-hole fibers has been widely explored for hydrostatic pressure measurement. Here, this paper studies the effects of the initial birefringence of a side-hole fiber on the pressure response of polarimetric sensors based on side-hole fibers. A mathematical model, where the stress field induced by the pressure is assumed to be uniform in the core region of the fiber, was established to calculate the birefringence and optical axis rotation as a function of the differences between the two principal stress components of the stress field in the core region. Simulation results show that when there is misalignment between the initial birefringence axes and the principal axes of the stress field, pressure changes cause rotations of the birefringence axis, leading to complicated and nonlinear changes of birefringence as a function of pressure. Experiments were conducted using fiber-Bragg-grating-based resonators on side-hole fibers with different initial birefringence, and the results agree well with the simulation. The results underscore the importance of the control of magnitude and direction of the initial birefringence of the side-hole fiber and provide guidelines for the design and fabrication of side-hole fiber pressure sensors.

42 ENGINEERING↗
DOE OSTI2024

Elucidating the Link Between Alkali Metal Ions and Reaction-Transport Mechanisms in Cathode Electrodes for Alkali-ion Batteries

Our long-term goal is to improve the reliability of electrode materials and their ability to transport and store various metal ions for electrochemical energy storage applications. The main objective of this work was to investigate the intrinsic relationship between the role of alkali metal ions and electrochemically driven mechanical stability and kinetic properties of battery materials. The overall question was “What is the role of alkali metal ions on the electrochemical and mechanical behavior of cathode electrodes? Our guiding hypothesis was that intercalation of larger alkali metal ions (Na and K) inevitably alters the coupled transport-reaction processes during battery operation in organic electrolytes, leading to more intensive chemo-mechanical instabilities in cathode electrodes, resulting in rapid capacity fade. To validate the hypothesis, we experimentally characterized the reaction-transport processes and governing forces driving the instability of electrode materials in different alkali metal-ion environments. The project had three main tasks. The first one was to investigate intercalation-induced strains and associated stress generation, and their impact on structural deformations in composite cathode electrodes. The second task focused on identifying potential-dependent dynamic changes in the electrode-electrolyte interface in alkali metal ion batteries. The last task was focused on determining how larger alkali metal ions with slower diffusivity affect the transport-mechanics coupling at faster scan rates, compared to smaller ions with faster diffusivity in electrodes. We shortly provided the outcome of each task in the accomplishment section. This project produced 10 peer-reviewed publications (9 research papers and one review manuscript) and supported two Ph.D. students, who graduated from Oklahoma State University.

25 ENERGY STORAGE↗
DOE OSTI2024

GQuEST Control System Resolution

GQuEST (Gravity from Quantum Entanglement of Space-Time), is a collaboration verifying a quantum gravity model by measuring holographic effects on a microscopic scale. Its interferometer apparatus filters excessive optical noise and requires a control system that can adjust the filtration to accommodate for frequency changes in the output light. We stress-test this control system by simulating filter behaviors with parameters in their outermost regimes, and we have determined a threshold that maintains precision while minimizing resource usage. These results are important for the successful operation of GQuEST's interferometer, enabling more accurate tests of quantum gravity models and thereby advancing our understanding of gravity at the quantum mechanical level.

Nguyen, David↗
DOE OSTI2025

Slow Strain Rate Testing of A537 Tank Wall Material

At Savannah River Site (SRS), High-Level Waste is stored in below-grade carbon steel tanks. This waste in part consists of sludge, salt cake, and/or supernate. Preparation of this waste for future processing involves dissolution of the salt cake layer. The salt dissolution process can create conditions that leave the carbon steel tanks susceptible to localized corrosion. The salt to be dissolved contains high concentrations of nitrate, that once released, create an environment that may be conducive to pitting corrosion and/or stress corrosion cracking (SCC) of carbon steel. The salt dissolution process also liberates interstitial liquid trapped between the salt crystals. This liquid is initially high in nitrite and hydroxide concentration. High pH and greater ratios of nitrite to nitrate act as inhibitors to minimize corrosion of carbon steel in high nitrate environments. However, as dissolution proceeds, the concentration of nitrate will increase, while the hydroxide and nitrite concentration of the interstitial liquid will deplete and become insufficient to prevent the onset of corrosion attack. Tank blending and the addition of inhibitors are used to ensure adequate concentrations of hydroxide and nitrite. However, this is not desirable during salt dissolution as it can reduce process efficiency and increase the amount of waste that needs processing. This testing program was designed to examine the risk of SCC associated with utilizing the pitting factor (PF) and nitrite/nitrate (NO 2 - /NO 3 - ) ratio limits for handling dissolved salt solutions at an elevated temperature in the carbon steel waste tanks. The previously identified limits are a PF of 1.2 and an NO 2 - /NO 3 - ratio of 0.15. The results indicate that as long as the NO 2 - /NO 3 - ratio exceeds 0.1 and the PF is above approximately 0.8, there is a discernible safety margin between the open circuit potential (OCP) and the critical cracking potential (CCP) observed during applied potential testing. However, this margin, defined by the difference between the OCP and CCP, is relatively narrow, ranging from 0.1 to 0.25 volts. This small margin raises concerns about potential shifts in OCP during waste retrieval operations, which could inadvertently increase the risk of SCC if the OCP approaches or exceeds the CCP. These results confirm that dissolved salt solutions provide a potent chemistry that, under certain conditions, makes carbon steel susceptible to SCC. The next question to consider is the influence these results have on decisions for storage and retrieval of waste from the tanks. For Type III/IIIA waste tanks, the risk of SCC remains very low. First, and most importantly, the post-weld stress relief of the tanks has reduced the residual stress near the welds. Thus, without the stress component, SCC risk is minimized. The material of construction (A537 Carbon steel) for the Type III/IIIA tanks is superior to the steel in its resistance to SCC than the steel that was utilized for the Type I, II, and IV tanks (A285 carbon steel). From a chemistry control standpoint for a Type III/IIIA tank directly involved with handling dissolved salt solutions, the PF and NO 2 - /NO 3 - ratio limits may be utilized wherein chemistry control provides an extra layer of defense against SCC. Chemistry control for a Type III/IIIA tank minimizes the risk for a tank that may receive the dissolved salt solution, particularly if that tank is a Type I, II, or IV waste tank. On the other hand, if the dissolved salt solution is handled by a Type I, II, or IV waste tank the risk of SCC is real. The potent chemistry, absence of stress relief, and inferior material result in a condition that is conducive to cracking. Efforts should be made to either avoid transferring waste that may not meet the PF and NO 2 - /NO 3 - ratio criteria to one of these tanks or if it is unavoidable, take measures to minimize the consequences of a leak. As shown by these tests, even if the PF and NO 2 - /NO 3 - ratio criteria are met, there is a risk that the tank potential may be disturbed in the positive direction and the risk of SCC increase.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Tuning the structure and superconductivity of SrNi 2⁢ P 2 by Rh substitution

The compound SrNi 2⁢ P 2 is unique among the ThCr 2 ⁢Si 2 class since it exhibits a temperature-induced transition upon cooling from an uncollapsed tetragonal (ucT) state to a one-third-collapsed orthorhombic (tcO) state where one out of every three P-rows bond across the Sr layers. This compound is also known for exhibiting bulk superconductivity below 1.4 K at ambient pressure. Here, in this paper, we report on the effects of Rh substitution in Sr⁢(Ni 1-x ⁢Rh x ) 2 ⁢P 2 on the structural and superconducting properties. We studied the variation of the nearest P-P distances as a function of the Rh fraction at room temperature, as well as its temperature dependence for selected compositions. We find that increasing the Rh fraction leads to a decrease in the transition temperature between the ucT and tcO states, until a full suppression of the tcO state for x ≥ 0.166. The superconducting transition first remains nearly insensitive to the Rh fraction, and then it increases to 2.3 K after the tcO state is fully suppressed. These results are summarized in a phase diagram, built upon the characterization by energy dispersive x-ray spectroscopy, x-ray diffraction, resistance, magnetization, and specific heat measurements done on crystalline samples with varying Rh content. The relationship between band structure, crystal structure, and superconductivity is discussed based on previously reported band structure calculations on SrRh 2 ⁢P 2 . Moreover, the effect of Rh fraction on the stress-induced structural transitions is also addressed by means of strain-stress studies done by uniaxial compression of single-crystalline micropillars of Sr⁢(Ni 1-x ⁢Rh x ) 2 ⁢P 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗
DOE OSTI2025

Challenges in Continuous In-Field Critical Current Testing of High-Temperature Superconducting Tapes: Thermal and Mechanical Perspectives

High-temperature superconductors (HTS) are essential for ultra-high-field applications requiring exceptional current-carrying capacity under extreme conditions. However, systematic characterization of critical current in long-length conductors remains challenging due to complex thermal, electromag netic, and mechanical interactions during continuous testing. This study reports the development of a continuous in-field magnetization testing system for position-dependent critical current measurement in HTS tapes at 20 K under 7.5 T fields applied normal to the tape plane, enabling identification of performance-limiting regions that could compromise magnet stability. Here, the system addresses two fundamental challenges inherent to cryogenic reel to-reel testing. First, thermal management requires continuous cooling of a moving conductor to 20 K, achieved through liquid nitrogen precooling combined with a 100 W@20 K Gifford McMahon cryocooler. Second, screening currents in high fields generate Lorentz forces that induce twisting, bowing, and potential delamination. To mitigate these risks, we propose mechanical reinforcement and active current density suppression strategies. Numerical simulations using the stream function formulation reveal four primary failure modes: frictional heating at guide interfaces, unstable equilibria causing deformation, transverse current-induced stresses at guide transitions, and unsupported forces in vertical spans. Our mitigation strategies include PTFE coated guides to minimize friction, spring-loaded stabilization mechanisms to maintain tape alignment, controlled pre-heating using the liquid nitrogen thermal jacket to suppress critical current at stress points, and optimized guide positioning to minimize force accumulation. The experimental system is nearing completion, with testing planned to commence within two months. Preliminary validation at 65 K under 0.5 T demonstrates strong correlation between simulation-predicted mechanical instabilities and observed critical current variations during conductor tran sitions through the measurement region. These findings establish a robust foundation for quality assurance protocols essential to next-generation superconducting magnet applications.

Chen, Siwei [Princeton Plasma Physics Laboratory (↗
DOE OSTI2025

Processing behavior evolution of recycled polypropylene: An integrated experimental and Computer-Aided engineering simulation study

Polypropylene (PP) comprises 21% of global plastics production and 18% of plastics waste, yet less than 1% of solid-waste PP is recycled in the United States (U.S.), representing significant environmental and economic challenges. Mechanical recycling, the most prevalent recycling method, subject's materials to thermomechanical stresses, which typically degrade polymer properties, affecting the quality of polymer products. This study replicates the impact of mechanical recycling through multiple extrusion cycles to examine the effects on PP's processing behavior. Dynamic scanning calorimetry (DSC) measurements showed stable melting behavior across all processing conditions, while crystallization analysis exhibited consistent shifts in kinetic parameters. Rheological characterization demonstrated progressive viscosity reductions through successive cycles, particularly pronounced at elevated reprocessing temperatures. Here, the integration of this experimental data into injection molding simulations showed that recycled PP maintains viable processing characteristics. Our findings establish quantitative correlations between processing history and material behavior, enabling optimization of processing parameters directly rather than relying on trial-and-error approaches. While these results reflect idealized recycling conditions with minimal contamination, they provide a framework for understanding fundamental property evolution during mechanical recycling.

42 ENGINEERING↗
DOE OSTI2025

Disruption of acyl-acyl carrier protein (acyl-ACP) synthetase in cyanobacteria impairs lipid remodeling as revealed by acyl-ACP measurements

Free fatty acid (FFA) production in bacteria is a key target for metabolic engineering. The knockout of the acyl-ACP synthetase (AAS) prevents reincorporation of FFA into the fatty acid biosynthetic cycle and is widely used to enhance their secretion. However, the role of AAS in membrane lipid remodeling under environmental stress, such as altered temperature, remains poorly understood. In cyanobacteria, temperature shifts are known to affect fatty acid desaturation and membrane fluidity, yet it is unclear whether AAS contributes to these adaptive responses through re-esterification of membrane-released acyl chains. We elucidated unique aspects of fatty acid metabolism in response to temperature changes in biotechnologically relevant microbes with the development of an efficient method for quantifying acyl-ACP intermediates using anion exchange chromatography (AEX). In Escherichia coli, which performs desaturation during fatty acid biosynthesis, we detected saturated and unsaturated acyl-ACPs that confirm biosynthetic pathway operation. In the cyanobacteria, Picosynechococcus sp. PCC 7002 and the Δaas strain, changes between two temperatures were interpreted with support from proteomic and lipidomic analyses and indicated that the AAS is tied to membrane lipid remodeling. Further, polyunsaturated acyl-ACPs were detected in the Δaas strain, which was unexpected because fatty acid synthesis does not produce polyunsaturates in cyanobacteria, suggesting the presence of alternative acyl-activating enzymes or unknown acyl-ACP desaturases. This study highlights the possible link between acyl chain recycling and lipid remodeling in cyanobacteria and demonstrates the utility of AEX-based acyl-ACP profiling in dissecting fatty acid metabolism.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Correlating processing variables to material properties in recycled polypropylene: A data‐driven approach

Abstract Polypropylene (PP) is one of the most widely used plastics, yet its recycling remains limited, with less than 1% of solid waste PP being reprocessed. Mechanical recycling through extrusion is the most practical method, but inconsistent reprocessing conditions introduce variability in material properties. While temperature, screw speed, and residence time influence the thermomechanical stress applied during reprocessing, there are no standardized guidelines for optimizing these parameters. This study examines how these factors shape the properties of recycled PP, using conditions designed to mimic post‐industrial recycled (PIR) scrap. Residence time was measured using colorimetric tracking and correlated with molecular weight, viscosity, and mechanical properties over multiple extrusion cycles. Data‐driven modeling, including response surface methodology, support vector machines, and artificial neural networks, identified processing temperature as the dominant factor in material degradation, followed by residence time. Mechanical properties remained stable, while viscosity decreased predictably with increasing residence time. By linking reprocessing conditions to property evolution, this study provides a method to optimize processing parameters and reduce variability in recycled PP. These findings help manufacturers improve process control, making recycled PP more predictable for reuse in manufacturing. Highlights Study of PIR‐quality PP without additives or compatibilizers. Residence time analysis shows processing temperature drives PP property changes. Mark‐Houwink enables quick molecular weight checks for quality control. Models predict mechanical and rheological shifts in reprocessing. Optimized processing parameters minimize property degradation in recycling.

Estela‐García, John E. [Polymer Engineering Center↗
DOE OSTI2025

Corrosion Fatigue Life Evaluation of 17-4PH in Support of Water Filled Turbine Hubs

High cycle corrosion fatigue (HCCF) life S-N tests were conducted on wrought 17-4PH in various water environments under accelerated testing conditions. For tests conducted in aerated Columbia River water and in aerated ASTM Type IV water, at ~10 6 cycles, the HCCF stress amplitude was ~70% of the value in air. For deaerated water, the value was ~80%. These values are consist with the small amount of literature data on HCCF life of 17-4PH in water environments. The measured fatigue life both in air and water are much better than the ASME trend curve of high cycle fatigue life of moderate and high strength steels. Measured values were also much better than found in a hydropower-relevant study in the literature on cast 17-4PH. The effect of Amersite 61W on HCCF life was evaluated and found to cause very low times to specimen failure compared to all other water environments.

13 HYDRO ENERGY↗
DOE OSTI2024

Simultaneous measurement of temperature and strain by cascaded fiber Bragg grating-silicon Fabry-Perot interferometer sensor

We report a fiber-optic sensor configuration with a cascaded fiber Bragg grating (FBG) and a silicon Fabry-Perot interferometer (FPI) for simultaneous measurement of temperature and strain. The sensor is composed of a 5 mm FBG on a single mode fiber and a 100μm thick silicon FPI attached to the tip of the optical fiber. The FBG is surface mounted on the host structure, and the FPI tip is suspended. Due to the stress-free, cantilever configuration, the silicon FPI is insensitive to strain, but sensitive to temperature with a sensitivity much higher than the FBG due to the large thermo-optic coefficient of silicon. The sensor is tested from room temperature to 100°C with varying strain up to ∼150με. The silicon FPI provides high temperature sensitivity of 89 pm/°C unaffected by strain. Since the FBG is attached to the host structure, it is affected by both thermal and mechanical strain; the sensitivity of these was experimentally obtained 32 pm/°C and 1.09 pm / με, respectively. Interrogated with a broadband light source and a high-speed spectrometer, the sensor shows temperature and strain resolutions of 1.9 × 10 −3 °C and 0.042 με, respectively. Here, due to the small size, enhanced sensitivity, and high resolution, this cascaded FBG-FPI sensor can be used in applications where accurate measurement of temperature and strain is required.

42 ENGINEERING↗