Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS RELAXATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

3D Microscopy to Assess the Effect of High Temperature Cyclic Oxidation on the Deformation of Cast and ODS FeCrAlY Alloys

Specimen deformation, oxide scale growth, and scale cracking were monitored for cyclic oxidation exposures at 1200 °C of three cast FeCrAlY(Hf) alloys and two oxide dispersion strengthened (ODS) FeCrAl alloys. Evolution of both the specimen geometry and surface deformation was quantified using 3D optical microscopy. The stress in the alumina scale was also measured using photo-stimulated luminescence piezospectroscopy. The goal was to examine the effect of stress generation and stress relaxation on scale spallation for FeCrAl materials with drastic differences in terms of high temperature strengths. After 1000, 1-h cycles, the cast alloys exhibited significant deformation with a convoluted oxide scale, leading for the two Hf-free FeCrAlY alloys to undergo crack formation and spallation. For the Hf-containing FeCrAlY, limited spallation was observed due to the localization of spallation at grain boundaries, the large grain structure, and the beneficial effect of Hf on scale adhesion. On the other hand, limited deformation was measured for the ODS FeCrAl alloys, with minimal cracking and scale spallation for alloy PM2000 after 1000 h. A higher spallation rate was observed for ODS MA956, which was attributed to a high defect concentration in the alumina scale that formed. The mechanisms leading to spallation during cyclic oxidation for the cast and ODS FeCrAlY alloys are described.

36 MATERIALS SCIENCE↗

Determination of γ/γ' Lattice Misfit in Ni-Based Single-Crystal Superalloys at High Temperatures by Neutron Diffraction

Constrained γ/γ' lattice misfit as a function of temperature (room temperature, 871 °C, 982 °C, 1093 °C, and 1204 °C) is measured by neutron diffraction on the first-generation Ni-based single-crystal superalloy René N4 and second-generation superalloys René N5, CMSX4, and PWA1484. All the alloys studied show negative misfit at temperatures above 871 °C. For René N4, René N5, and PWA1484, the misfit becomes less negative at temperatures above 1093 °C, possibly due to either the chemistry effect or internal stress relaxation. The magnitude of the misfit shows a qualitative agreement with Caron’s misfit model based on Vegard’s coefficients. The Re-free alloy René N4 was found to have a larger γ lattice parameter and γ/γ' misfit due to higher fractions of Cr, Ti, and Mo. After 100 hours of annealing at high temperatures, René N5 shows a more negative misfit than the misfit after the standard heat treatment.

36 MATERIALS SCIENCE↗

Three-dimensional local residual stress and orientation gradients near graphite nodules in ductile cast iron [3D local residual stress and orientation gradients near graphite nodules in ductile cast iron]

A synchrotron technique, differential aperture X-ray microscopy (DAXM), has been applied to characterize the microstructure and analyze the local mesoscale residual elastic strain fields around graphite nodules embedded in ferrite matrix grains in ductile cast iron. Compressive residual elastic strains are measured with a maximum strain of ~6.5–8 × 10 –4 near the graphite nodules extending into the matrix about 20 μm, where the elastic strain is near zero. The experimental data are compared with a strain gradient calculated by a finite element model, and good accord has been found but with a significant overprediction of the maximum strain. This is discussed in terms of stress relaxation during cooling or during storage by plastic deformation of the nodule, the matrix or both. Furthermore, relaxation by plastic deformation of the ferrite is demonstrated by the formation of low energy dislocation cell structure also quantified by the DAXM technique.

36 MATERIALS SCIENCE↗

In situ, 3D characterization of the deformation mechanics of a superelastic NiTi shape memory alloy single crystal under multiscale constraint

Microstructural elements in NiTi shape memory alloys (SMAs) – precipitates, phase boundaries, inclusions, grain boundaries – can be viewed as sources of multiscale constraint that influence their deformation response. In this paper, we characterized in situ, and in 3D, the deformation and the evolution of microstructure during a tension test in a superelastic NiTi specimen containing some of these sources of constraint. The method used was far-field high-energy X-ray diffraction microscopy (ff-HEDM), complemented by electron microscopy. We simulated the local stress state in the specimen using a microstructural model informed by the experimental data. Using these combined microstructure, deformation, and stress data, we report three phenomena, and relate them to specific sources of constraint. During initial elastic loading, axial lattice strain in austenite increased monotonically. On partial stress-induced phase transformation to martensite, the stress redistributed to both phases leading to a stress relaxation in austenite. The specimen contained a dense distribution of inclusions, which led to the activation of martensite habit plane variants that produce less than theoretical maximum transformation strain. Large Ni 4 Ti 3 precipitates potentially contributed to the poor transformation response. Under load, proportional gradients in local rotation and elastic stretch developed in the martensite phase, because of the constraint at phase interfaces. Finally, this combined ff-HEDM, electron microscopy, microstructural simulation toolbox provides a versatile method to understand the effect of constraint on inelastic deformation in other alloys with hierarchical microstructure.

36 MATERIALS SCIENCE↗

The influence of plasticity-induced crack closure on creep-fatigue crack growth in two heat-resistant steels

Finite element simulations are performed to predict plasticity-induced crack closure and creep-fatigue crack growth rates in two heat-resistant steels, the austenitic 20Cr-25Ni (Alloy 709) and martensitic 9Cr-1Mo (modified 1Cr-9Mo) steels. In a creep-fatigue cycle, total crack growth rate is usually computed by the addition of the fatigue crack growth rate during cyclic loading and creep crack growth rate during hold time. Two-dimensional finite element analyses of compact tension specimens are performed to simulate crack growth under cyclic and time-dependent loading conditions, with the consideration of elastic-plastic and creep deformations of the material at the crack tip. The simulations quantify the effect of hold time on crack opening load induced by the combined action of plasticity-induced crack closure and creep-induced stress relaxation at the crack tip. It is shown that increasing hold time during a creep-fatigue cycle results in a decrease of crack-tip opening load, thus increasing crack growth rate during the next cyclic loading. Experimental results of creep-fatigue crack growth rates in Alloy 709 are presented. The finite element simulations predicted crack growth rates under creep-fatigue loading in agreement with experimental values for both Alloy 709 and modified 9Cr-1Mo steels.

36 MATERIALS SCIENCE↗

A new experimental testing method for investigation of creep-dominant creep-fatigue interaction in Alloy 617 at 950 °C

An experimental testing procedure is proposed for generating creep-dominant creep-fatigue interaction in Alloy 617 at 950 °C. Most experimental studies on Alloy 617 at elevated temperatures employ a purely strain-controlled loading waveform with a tensile hold period. Strain-controlled loading can only generate interaction in the fatigue-dominant regime of the damage interaction diagram, due to the saturation effect of increasing hold time on cycle life. This saturation is caused by the rapid stress relaxation of Alloy 617 at high temperatures. Design codes for components undergoing creep-fatigue interaction at high temperatures require creep-fatigue testing data in the creep-dominant regime. Here this study investigates multiple creep-fatigue loading waveforms with the objective of producing creep-dominant interaction. The custom loading waveforms are implemented on a servo-hydraulic load frame with a furnace. A hybrid-control scheme with strain-controlled ramps and load-controlled hold periods is proposed due to its flexibility in generating varying proportions of creep and fatigue damage. Experimental data is presented and different loading schemes are compared. Special emphasis is on the creep and fatigue damage contributions by the newly proposed testing method. Several conclusions are discussed and an extension of this current work is suggested to improve the damage interaction diagram for design purposes.

36 MATERIALS SCIENCE↗

A method for predicting failure statistics for steady state elevated temperature structural components

This paper presents the initial development of a high temperature life prediction method that accounts for the variability in the material properties of Grade 91 steel. The method accounts for material variability by fitting a variable 3-parameter Weibull distribution to experimental rupture data and accounts for the variability of creep deformation on the steady-state stresses via a Monte Carlo approach. To ensure reasonable computational times, the model represents the material as an extremely viscous Stokes fluid with a non-Newtonian viscosity, therefore solving the stress relaxation problem with a steady, static, instead of transient, analysis. Furthermore, the complete statistical analysis combines this model for creep deformation with a probabilistic model for creep rupture to evaluate the probability of premature failure for a set of sample problems, comparing the predicted failure statistics to the design life predicted by the ASME Boiler and Pressure Vessel Code rules.

42 ENGINEERING↗

X-ray topographic study of growth defects of trans-stilbene crystals grown from solutions

Single crystals of trans-stilbene, C 14 H 12 , with properties suitable for high-energy neutron detection were grown from solution in anisole and toluene by the temperature reduction method with growth rates up to 6 mm/day. From these crystals, slices of appropriate orientation and thickness of 2–4 mm were cut and studied by X-ray diffraction topography applying the Lang method using CuKα radiation. The topographs exhibit growth defects such as liquid inclusions, dislocations, striations, and faulty growth-sector boundaries. These defects occur in the same typical arrangements and geometries as is observed in all kinds of crystals grown on habit faces from solution. Besides growth dislocations originating from inclusions and propagating with the growth front, many plastic glide dislocations in the shape of loops or half-loops emitted from inclusions by stress relaxation are observed. Finally, the glide system underlying this plasticity is discussed.

36 MATERIALS SCIENCE↗

Mechanical properties of ZrB2- and HfB2-based ultra-high temperature ceramics fabricated by spark plasma sintering

Flexural strengths at room temperature, at 1400 C in air and at room temperature after 1 h oxidation at 1400 C were determined for ZrB2- and HfB2-based ultra-high temperature ceramics (UHTCs). Defects caused by electrical discharge machining (EDM) lowered measured strengths significantly and were used to calculate fracture toughness via a fracture mechanics approach. ZrB2 with 20 vol.% SiC had room temperature strength of 700 90 MPa, fracture toughness of 6.4 0.6 MPa, Vickers hardness at 9.8 N load of 21.1 0.6 GPa, 1400 C strength of 400 30 MPa and room temperature strength after 1 h oxidation at 1400 C of 678 15 MPa with an oxide layer thickness of 45 5 m. HfB2 with 20 vol.% SiC showed room temperature strength of 620 50 MPa, fracture toughness of 5.0 0.4 MPa, Vickers hardness at 9.8 N load of 27.0 0.6 GPa, 1400 C strength of 590 150 MPa and room temperature strength after 1 h oxidation at 1400 C of 660 25 MPa with an oxide layer thickness of 12 1 m. 2 wt.% La2O3 addition to UHTCs slightly reduced mechanical performance while increasing tolerance to property degradation after oxidation and effectively aided internal stress relaxation during spark plasma sintering (SPS) cooling, as quantified by X-ray diffraction (XRD). Slow crack growth was suggested as the failure mechanism at high temperatures as a consequence of sharp cracks formation during oxidation.

Zapata-Solvas, E.↗

A constitutive framework for rocks undergoing solid dissolution

Here, we formulate a time-dependent damage theory for rocks subjected to mechanical deformation and solid dissolution. The constitutive description is inspired by the transition state theory, which states that the rate of dissolution is a function of the reactive surface area measured through the crack density in the volume. We use a gradient-enhanced damage framework in which damage depends on the deformation of the material as well as on the amount of solid mass dissolved over time. The gradient-enhanced formulation is characterized by a three-field variational formulation with the solid displacement, nonlocal equivalent strain, and nonlocal rate of solid dissolution as the basic state variables. Traditionally, time-independent damage theories have only allowed damage to increase with increasing external load. In the proposed framework, the degree of damage may increase due to solid dissolution even when the external load is held fixed. In this way, solid dissolution is viewed as a process that is responsible for bringing about rate-dependent effects such as creep and stress-relaxation, which are two common features of geomaterial behavior.

42 ENGINEERING↗

Irradiation creep of nano-powder sintered silicon carbide at low neutron fluences

The irradiation creep behavior of nano-powder sintered silicon carbide was investigated using the bend stress relaxation method under neutron irradiation up to 1.9 dpa. The creep deformation was observed at all temperatures ranging from 380 to 1180 °C mainly from the irradiation creep but with the increasing contributions from the thermal creep at higher temperatures. Microstructural observation and data analysis were performed.

36 MATERIALS SCIENCE↗

Strain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components

Inconel® 740H components produced via laser-powder-bed fusion (L-PBF) additive manufacturing are ideal for supercritical CO2 primary heat exchangers. Arc welding is often needed, and subsequent post-weld heat treatment aging at 790–840 °C is required to improve strength via gamma prime (γ’) precipitation; however, strain age cracking (SAC) can occur in the heat affected zone (HAZ) during this process. This study uses stress relaxation testing at 800 °C on simulated HAZ specimens from vertically and horizontally built L-PBF IN740H to assess SAC susceptibility across heating rates of 40–3480 °C/h and weld-induced strains of 3–10 %. Vertical builds require greater mechanical energy input and exhibit longer times to fracture than horizontal builds, and time to fracture occurs sooner at slower heating rates. Creep voids were observed in γ’-denuded regions along grain boundaries, and cracking propagated along migrated grain boundaries and at interfaces between elongated secondary phases (γ’ or carbides) and the γ-matrix.

14 SOLAR ENERGY↗

Characterizing and modeling the mechanical behavior of an anion exchange membrane for carbon capture applications

A new direct air capture (DAC) technology uses a moisture swing (MS) process with anion exchange membranes, potentially offering a more energy-efficient way to remove CO₂ from the air. In this MS process, the membrane absorbs CO₂ as it dries and releases it when water is added. Understanding the mechanical behavior of these membranes is essential for improving the design and efficiency of DAC systems and prolonging sorbent lifetime. This study tested one anion exchange membrane, Fumasep’s FAA-3, under mechanical loading and various temperature and humidity conditions to measure its swelling, stiffness, strength, plastic deformation, and stress relaxation. Experimental results were used to identify a mechanical model for FAA-3 that can be used to predict the material’s nonlinear viscous behavior under various loads and environments. Unlike prior studies that assumed linear elastic behavior, this work incorporates humidity-dependent swelling, thermal expansion, and nonlinear viscoelasticity of FAA-3 in both the experiments and the model.

Direct air capture↗

Reprocessable and Recyclable Polymer Network Electrolytes via Incorporation of Dynamic Covalent Bonds

Mechanically durable polymer network electrolytes are desirable for batteries; however, covalent cross-linking adversely affects their large-scale manufacturing, and they are difficult to recycle post-lifespan. In this work, we address the electrolyte reprocessability and recyclability challenges through the use of dynamic covalent bonds for polymer network solid electrolytes. Specifically, the associative dynamic vinylogous urethane motif is incorporated into a poly(ethylene oxide) network electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt. The resulting dynamic covalent network electrolyte possesses a modest ion conductivity (~10–5 S/cm at room temperature) and good reprocessability. Stress–relaxation studies indicate that the LiFSI salt can catalyze the bond exchange and enhance the network dynamics. Furthermore, the reprocessability associated with bond exchange can be tuned by simply adjusting the formulation of reagent compositions, in which increasing the amount of excess amine or using a shorter chain of PEO prepolymer can further enhance the network dynamics and corresponding reprocessability.

25 ENERGY STORAGE↗

Thin-Film Fracture Behavior for Diketopyrrolopyrrole Semiconducting Polymeric Films

Fracture energy, which quantifies a material’s resistance to the propagation of a pre-existing crack, is a key parameter for ensuring the mechanical reliability of stretchable organic electronic devices. However, most existing methods, such as a four-point bending fracture energy, utilized for measuring the fracture energy of semiconducting polymeric thin films are complicated by substrate effects, making it challenging to isolate the intrinsic behavior of the film from interfacial influences. In this study, we employed a pseudo free-standing pure shear method to systematically investigate the cohesive fracture energy of poly(diketopyrrolopyrrole-terthiophene) P(DPP-T)-based thin films to examine the effects of nanoconfinement, side chain length, degree of crystallinity, and strain rates. This method effectively eliminates substrate interference, enabling a direct assessment of the cohesive fracture energy of P(DPP-T) thin films. We found that thinner films and those with lower molecular weights exhibited significantly reduced fracture energies due to diminished chain entanglements. Additionally, films with shorter side chains displayed notably higher fracture energies, which were attributed to an increase in the degree of crystallinity. Finally, slower strain rates led to higher fracture energies, consistent with an enhanced stress relaxation. These insights offer practical guidelines for designing mechanically robust semiconducting polymers, contributing to the advancement of reliable, durable, flexible, and wearable electronic devices.

Zhang, Song [Univ. of Southern Mississippi, Hattie↗

Green Catalysts for Reprocessing Thermoset Polyurethanes

Polyurethane (PU) thermosets are usually landfilled at the end of their service lifetimes and cannot be recycled through conventional means. Although dibutyltin dilaurate (DBTDL) is an effective catalyst for reprocessing PU thermosets, organotins are immunotoxic and teratogenic, which is concerning for catalysts embedded within covalent adaptable networks (CANs). Here, we identify Zr(acac) 4 and Zr(tmhd) 4 as catalysts to reprocess PU CANs more sustainably. Thermoset PU foams containing Zr-based catalysts exhibit characteristic stress relaxation times between 6 and 200 s, similar or faster than DBTDL. These catalysts are capable of reprocessing a PU foam for four or five cycles. Dynamic mechanical thermal analysis indicates that zirconium-based catalysts preserve glass transition temperature and crosslink density between cycles and are promising catalysts for bulk reprocessing of thermoset PUs. Here, a solvent-free reprocessing method was developed by co-milling the PU foam and the Zr catalyst. Ultimately, these reprocessing methods using Zr-based catalysts will impart greater sustainability and circularity to PU plastics.

Catalysts↗