Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scan Mirror”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Spectral infrared hemispherical reflectance measurements for LDEF tray clamps

This paper describes infrared hemispherical reflectance measurements (2-15 microns) that were made on 58 chromic acid anodized tray clamps retrieved from the LDEF spacecraft. These clamps were used for maintaining the experiments in place and were located at various locations about the spacecraft. Changes in reflectance of the tray clamps at these locations were compared with atomic oxygen fluxes at the same locations. A decrease in absorption band depth was seen for the surfaces exposed to space indicating that there was some surface layer erosion. In all of the surfaces measured, little evidence of contamination was observed and none of the samples showed evidence of the brown nicotine stain that was so prominent in other experiments. Total emissivity values were calculated for both exposed and unexposed tray clamp surfaces. Only small differences, usually less than 1 percent, were observed. The spectral reflectances were measured using a hemi-ellipsoidal mirror reflectometer matched with an interferometer spectrometer. The rapid scanning capability of the interferometer allowed the reflectance measurements to be made in a timely fashion. The ellipsoidal mirror has its two foci separated by 2 inches and located on the major axis. A blackbody source was located at one focus while the tray clamp samples were located at the conjugate focus. The blackbody radiation was modulated and then focused by the ellipsoid onto the tray clamps. Radiation reflected from the tray clamp was sampled by the interferometer by viewing through a hole in the ellipsoid. A gold mirror (reflectance approximately 98 percent) was used as the reference surface.

Wood, Bobby E.↗
NASA NTRS1991

Voyager photometry of Triton - Haze and surface photometric properties

The Voyager whole-disk observations of Triton at 0.41, 0.48, and 0.56 micron filter wavelengths are analyzed using a model which combines an improved version of Hapke's photometric equation with a thin atmospheric haze layer in the appropriate spherical geometry. The model is shown to describe accurately the phase curves over a range of phase angles and to agree with disk-resolved brightness scans along the photometric equator and mirror meridian. According to the model, the photometric parameters of Triton's regolith are reasonably typical of icy satellites, except for the extremely high (close to unity) single-scattering albedo.

Hillier, J.↗
NASA NTRS1995

Effects of low earth orbit on the optical performance of multi-layer enhanced high reflectance mirrors

Two mirror designs developed for space applications were flown along with a standard mid-infrared design on the leading and trailing edges of the Long Duration Exposure Facility (LDEF). Preliminary observations of induced changes in optical performance of ZnS-coated mirrors and impact-related microstructural and microchemical effects are described in the proceedings of the First LDEF Post-Retrieval Symposium. In this paper, effects of the induced environment and meteoroid/debris impacts on mirror performance are described in more detail. Also, an analysis of reflectance spectra using the results of Auger and secondary ion mass spectroscopy (SIMS) profiling measurements are used to identify an optical-degradation mechanism for the ZnS-coated mirrors. Structural damage associated with a high-velocity impact on a (Si/Al2O3)-coated mirror was imaged optically and with scanning electron and atomic force microscopy (SEM and AFM). Scanning Auger and SIMS analysis provided chemical mapping of selected impact sites. The impact data suggest design and fabrication modifications for obtaining improved mechanical performance using a design variation identified in preflight laboratory simulations. Auger surface profile and SIMS imaging data verified the conclusion that secondary impacts are the source of contamination associated with the dendrites grown on the leading-edge ZnS-coated test samples. It was also found that dendrites can be grown in the laboratory by irradiating contaminated sites on a trailing-edge ZnS-coated sample with a rastered electron beam. These results suggest a mechanism for dendrite growth.

Donovan, Terence↗
NASA NTRS2004

Discrete Wavelength-Locked External Cavity Laser

A prototype improved external cavity laser (ECL) was demonstrated in the second phase of a continuing effort to develop wavelength-agile lasers for fiber-optic communications and trace-gas-sensing applications. This laser is designed to offer next-generation performance for incorporation into fiber-optic networks. By eliminating several optical components and simplifying others used in prior designs, the design of this laser reduces costs, making lasers of this type very competitive in a price-sensitive market. Diode lasers have become enabling devices for fiber optic networks because of their cost, compactness, and spectral properties. ECLs built around diode laser gain elements further enhance capabilities by virtue of their excellent spectral properties with significantly increased (relative to prior lasers) wavelength tuning ranges. It is essential to exploit the increased spectral coverage of ECLs while simultaneously insuring that they operate only at precisely defined communication channels (wavelengths). Heretofore, this requirement has typically been satisfied through incorporation of add-in optical components that lock the ECL output wavelengths to these specific channels. Such add-in components contribute substantially to the costs of ECL lasers to be used as sources for optical communication networks. Furthermore, the optical alignment of these components, needed to attain the required wavelength precision, is a non-trivial task and can contribute substantially to production costs. The design of the present improved ECL differs significantly from the designs of prior ECLs. The present design relies on inherent features of components already included within an ECL, with slight modifications so that these components perform their normal functions while simultaneously effecting locking to the required discrete wavelengths. Hence, add-in optical components and the associated cost of alignment can be eliminated. The figure shows the locking feedback signal, and the frequency locking achieved by use of this signal, as a mirror is tilted through a range of angles to tune the ECL through 48 channels. The data for the frequency plot were obtained, simultaneously with the data for the locking-signal plot, by using a scanning Michelson interferometer to precisely determine the ECL wavelength (and, hence, frequency). Given the ability of the Michelson interferometer to obtain highly precise readings, the frequency plot can be taken to be a reliable indication of single-mode operation. The discontinuities in the frequency plot signify the switching of the ECL between channels; in other words, they indicate tuning with locking to discrete frequencies. The peaks of the feedbacklocking signal correspond to the centers, or near centers, of the mirror angle scan through the corresponding channels. Thus, it is clear that when the feedback-locking signal is at a local maximum, the ECL is operating at single frequency at or near the middle frequency of the selected channel. This is all that is required for precisely locking the ECL output wavelength. The locking is achieved without additional external optical components.

Pilgrim, Jeffrey S.↗
NASA NTRS1992

Atomic oxygen effects on thermal control and mirror coatings: Evaluation of experiment A0034

Evaluation of the degradation attributed to contamination of the collector mirrors in Experiment A0034, which were exposed to an earth orbital environment while on the leading and trailing edges of the LDEF, has provided some evidence for outgassing of coatings stimulated by atomic oxygen. Effects of the natural space environment on the coatings and mirrors, including the effects of incident and re-directed atomic oxygen flux, were investigated. The effects of exposure on the coatings and mirrors were evaluated by optical, surface profiling, chemical, and scanning electron microscopy (SEM) measurements. Preliminary results of these analyses are discussed for application to both the issues of mirror and coating stability and the specific issue of atomic oxygen stimulated outgassing.

Linton, Roger C.↗
NASA NTRS2014

Boundary Layer Transition Detection on a Rotor Blade Using Rotating Mirror Thermography

Laminar-to-turbulent transition on a rotor blade in hover has been imaged using an area-scan infrared camera. A new method for tracking a blade using a rotating mirror was employed. The mirror axis of rotation roughly corresponded to the rotor axis of rotation and the mirror rotational frequency is 1/2 that of the rotor. This permitted the use of cameras whose integration time was too long to prevent image blur due to the motion of the blade. This article will show the use of this method for a rotor blade at different collective pitch angles.

Imaging↗
NASA NTRS2005

Two-Photon Fluorescence Microscope for Microgravity Research

A two-photon fluorescence microscope has been developed for the study of biophysical phenomena. Two-photon microscopy is a novel form of laser-based scanning microscopy that enables three-dimensional imaging without many of the problems inherent in confocal microscopy. Unlike one-photon optical microscopy, two-photon microscopy utilizes the simultaneous nonlinear absorption of two near-infrared photons. However, the efficiency of two-photon absorption is much lower than that of one-photon absorption, so an ultra-fast pulsed laser source is typically employed. On the other hand, the critical energy threshold for two-photon absorption leads to fluorophore excitation that is intrinsically localized to the focal volume. Consequently, two-photon microscopy enables optical sectioning and confocal performance without the need for a signal-limiting pinhole. In addition, there is a reduction (relative to one-photon optical microscopy) in photon-induced damage because of the longer excitation wavelength. This reduction is especially advantageous for in vivo studies. Relative to confocal microscopy, there is also a reduction in background fluorescence, and, because of a reduction in Rayleigh scattering, there is a 4 increase of penetration depth. The prohibitive cost of a commercial two-photon fluorescence-microscope system, as well as a need for modularity, has led to the construction of a custom-built system (see Figure 1). This system includes a coherent mode-locked titanium: sapphire laser emitting 120-fs-duration pulses at a repetition rate of 80 MHz. The pulsed laser has an average output power of 800 mW and a wavelength tuning range of 700 to 980 nm, enabling the excitation of a variety of targeted fluorophores. The output from the laser is attenuated, spatially filtered, and then directed into a confocal scanning head that has been modified to provide for side entry of the laser beam. The laser output coupler has been replaced with a dichroic filter that reflects the longer-wavelength excitation light and passes the shorter-wavelength fluorescence light. Also, the confocal pinhole has been removed to increase the signal strength. The laser beam is scanned by a twoperpendicular- axis pair of galvanometer mirrors through a pupil transfer lens into the side port of an inverted microscope. Finally, the beam is focused by a 63-magnification, 1.3-numerical- aperture oil-immersion objective lens onto a specimen. The pupil transfer lens serves to match the intermediate image planes of the scanning head and the microscope, and its location is critical. In order to maximize the quality of the image, (that is, the point spread function of the objective lens for all scan positions), the entire system was modeled in optical-design software, and the various free design parameters (the parameters of the spatial-filter components as well as the separations of all of the system components) were determined through an iterative optimization process. A modular design was chosen to facilitate access to the optical train for future fluorescence correlation spectroscopy and fluorescence-lifetime experiments.

Fischer, David G.↗
NASA NTRS1970

Electronic scanning of 2-channel monopulse patterns

Scanning method involves separation of scanning capability into two independent degrees of freedom. One degree of freedom corresponds to azimuthal scanning and other to elevation scanning on spiral coordinate axes. Scanning of both prime-feed and mirrored patterns is accomplished with reduction of mechanical vibration damage to large antennas.

Schmidt, R. F.↗
NASA NTRS1974

Geometric distortions of autocollimation type scanners

One criterion of image quality is its geometric similarity to the control test. The ability of television, phototelevision, phototelegraphic, and other systems to transmit geometrically similar images is characterized by the geometric distortion coefficient. Linear distortions result from the inaccuracy of scanning mechanism element assembly, and distortions can be minimized during adjustment operations or may be easily compensated during image reception. Brief descriptions are given of the possible sources of nonlinear distortions which arise in these devices due to the scanning mechanism, objective distortion, or the nodding mirror.

Narayeva, M. K.↗
NASA NTRS1993

Surface finish quality of the outer AXAF mirror pair based on X-ray measurements of the VETA-I

We employ the X-ray measurements of the VETA-I taken at the X-Ray Calibration Facility (XRCF) of the Marshall Space Flight Center (MSFC) to extract information about the surface finish quality of the outermost pair of AXAF mirrors. The particular measurements we consider are 1D scans of the core of the point response function (PRF) (FWHM scans), the encircled energy as a function of radius, and 1D scans of the wings of the PRF. We discuss briefly our raytrace model which incorporates the numerous effects present in the VETA-I test, such as the finite source distance, the size and shape of the X-ray source, the residual gravitational distortions of the optic, the despace of the VETA-I, and particulate contamination. We show how the data constrain the amplitude of mirror surface deviations for spatial frequencies greater than about 0.1/mm. Constraints on the average amplitude of circumferential slope errors are derived as well.

Hughes, John P.↗
NASA NTRS1975

Laser space rendezvous and docking system trade-off study

The use, design, and fabrication feasibility of scanning the laser beam by swiveling the outside mirror with a ball joint swivel system is examined along with the applicability of graphite reinforced epoxy material for the construction of reflective optics. It is indicated that (1) the cost of graphite-epoxy will be more than that of many other materials due to the amount of special tooling required; (2) the weight advantage of graphite-epoxy over beryllium is minimal; the ball joint swivel system is accurate enough to perform the scanning function; and that the ball joint will result in a simpler and more cost effective scanning mechanism.

Adelman, S.↗
NASA NTRS1975

A wide angle search technique for a 10.6 micron ladar

A ladar (laser radar) sensor designed around a pulsed passively Q-switched CO2 laser, capable of a efficient and rapid scans with a narrow beam over a wide field of view, is considered for surveillance and tracking applications in space. The output is a train of narrow pulses with a controllable pulse repetition rate. A resonant vibrating mirror in back of a classical Gregorian telescope, and a plane pointing mirror in front for beam steering, are used in scanning. Scan pulse sequences are described and illustrated. The 10.6 micron ladar set is under consideration as baseline sensor for various space rendezvous and docking applications.

Levinson, S.↗
NASA NTRS2000

Lightweight Lidar Telescopes for Space Applications

NASA is intent on exploiting the unique perspective of space-based remote optical instruments to observe and study large-scale environmental processes. Emphasis on smaller and more affordable missions continues to force the remote sensing instruments to find innovative ways to reduce the size, weight, and cost of the sensor package. This is a challenge because many of the proposed instruments incorporate a high quality meter-class telescope that can be a significant driver of total instrument costs. While various methods for telescope weight reduction have been achieved, many of the current approaches rely on exotic materials and specialized manufacturing techniques that limit availability or substantially increase costs. A competitive lightweight telescope technology that is especially well suited to space-based coherent Doppler wind lidar has been developed through a collaborative effort involving NASA Marshall Space Flight Center (MSFC) through the Global Hydrology and Climate Center (GHCC) and the University of Alabama in Huntsville (UAH) at the Center for Applied Optics (CAO). The new lightweight optics using metal alloy shells and surfaces (LOMASS) fabrication approach is suitable for high quality metal mirrors and meter-class telescopes. Compared to alternative materials and fabrication methods the new approach promises to reduce the areal density of a meter-class telescope to less than 15-kg/sq m; deliver a minimum VIO-RMS surface optical quality; while using commercial materials and equipment to lower procurement costs. The final optical figure and finish is put into the mirrors through conventional diamond turning and polishing techniques. This approach is especially advantageous for a coherent lidar instrument because the reduced telescope weight permits the rotation of the telescope to scan the beam without requiring heavy wedges or additional large mirrors. Ongoing investigations and preliminary results show promise for the LOMASS approach to be successful in demonstrating a novel alternative approach to fabricating lightweight mirrors with performance parameters comparable with the Space Readiness Coherent Lidar Experiment (SPARCLE). Development and process characterization is continuing with the design and fabrication of mirrors for a 25-cm telescope suitable for a lidar instrument.

Peters, Bruce R.↗
NASA NTRS1992

Surface finish quality of the outer AXAF mirror pair based on x ray measurements of the VETA-I

We employ the X-ray measurements of the VETA-I taken at the X-Ray Calibration Facility (XRCF) of the Marshall Space Flight Center (MSFC) to extract information about the surface finish quality of the outermost pair of AXAF mirrors. The particular measurements we consider are one dimensional scans of the core of the point response function (PRF) (full width half maximum (FWHM) scans), the encircled energy as a function of radius, and one dimensional scans of the wings of the PRF. We discuss briefly our ray trace model which incorporates the numerous effects present in the VETA-I test, such as the finite source distance, the size and shape of the X-ray source, the residual gravitational distortions of the optic, the despace of the VETA-I, and particulate contamination. We show how the data constrain the amplitude of mirror surface deviations for spatial frequencies greater than about 0.1 mm(exp -1). Constraints on the average amplitude of circumferential slope errors are derived as well.

Hughes, John P.↗
DOE OSTI2025

Topological excitonic insulator with tunable momentum order

Correlated topological materials often maintain a delicate balance among physical symmetries. Many topological orders are symmetry protected, whereas most correlated phenomena arise from spontaneous symmetry breaking. Cases where symmetry breaking induces a non-trivial topological phase are rare. Here we demonstrate the presence of two such phases in Ta 2 Pd 3 Te 5 , where Coulomb interactions form excitons that condense below 100 K, one with zero and the other with finite momentum. We observed a full spectral bulk gap, which stems from exciton condensation. This topological excitonic insulator state spontaneously breaks mirror symmetries but involves a weak structural coupling. Scanning tunnelling microscopy shows gapless boundary modes in the bulk insulating phase. Their magnetic field response, together with theoretical modelling, indicates a topological origin. These observations establish Ta 2 Pd 3 Te 5 as a topological excitonic insulator in a three-dimensional crystal. Finally, our results manifest a unique sequence of topological exciton condensations in a bulk crystal, offering exciting opportunities to study critical behaviour and excitations.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Multispectral scanner, thematic mapper, and beyond

The capabilities and functions of the Landsat D multispectral scanner (MSS) and thematic mapper (TM) are explored as a basis for improvements to satisfy increasing user demands. The MSS is an object-space line scanner for gathering data in four spectral bands ranging from 0.5-1.1 micron. In a 705 km near-polar sunsynchronous orbit, the MSS will generate 185 x 185 km imagery with 80 x 80 m ground resolution, mapping the entire earth every 16 days. Photomultiplier tubes are used for four of the bands and the other employs Si photodiodes. A calibration light source provides in orbit calibration during every reverse scan period of a pivotal on-board mirror. The TM collects data in seven bands from 0.45-12.5 microns, yielding a ground resolution of 30 x 30 m in six bands for reflected sunlight and 120 x 120 m for the 10.4-12.5 thermal bands. The addition of 16 Si detectors for 0.9-1.1 micron viewing for agricultural purposes, as well as higher resolution, is discussed.

Jones, C. R.↗
NASA NTRS2002

Mirrors Steer NASA in the Right Direction

Left Hand Design completed the production of the fine-steering mirror technology through 1995 Phase I and 1996 Phase II SBIR contracts with JPL's Interferometric Astronomy group. Presently, the work resulting from the collaboration with NASA represents the company's main line of products for the commercial sector. Aerospace-related applications include: image motion compensation; interceptor seekers for the U.S. Army and Navy; Earth observation and resource monitoring from spacecraft and airborne platforms; space astronomy; helicopter-based surveillance; and interferometric metrology. Left Hand Design's fine-steering mirrors have also penetrated the commercial marketplace with non-aerospace applications, including laser communications, video cameras, infrared inspection, solar observatories, and bathymeters. These cost-effective, commercial mirrors perform a variety of functions, such as scanning, alignment, chopping, tracking, pointing, and beam stabilization. Potential future applications include laser surgery and photolithography.

Source record↗