Results for “Simulation Fidelity” — Page 14

NASA NTRSDate not supplied

Modeling and Simulation of Rotary Sloshing in Launch Vehicles

The nonlinear dynamics of propellant sloshing during orbital ascent are usually neglected in the flight control analysis of large boost vehicles under the assumption that the viscous damping of the fluid is sufficient to suppress nonlinear phenomena and confine the fluid to small, planar free surface displacements. In this case, the sloshing dynamics can be modeled using a spring-mass-damper or linearized pendulum mechanical analog. However, large, smooth-wall tanks without significant internal hardware or ring baffles are still susceptible to nonlinear effects. In particular, rotary sloshing can present a risk to flight control as it involves the formation of a stable limit cycle which can lead to undesirable roll coupling. The underlying phenomena of jump resonance does not manifest in linear models, but can be reproduced using a nonlinear spherical pendulum or the Bauer paraboloid model developed during the Apollo/Saturn program. In this paper, a detailed analysis of the rotary sloshing dynamics of these mechanical analogs is presented, and discussed in the context of flight control stability. High-fidelity simulations of a representative boost vehicle are used to verify the semi-analytical predictions of the nonlinear dynamic response.

Modeling↗

NASA NTRSDate not supplied

End-To-End Uncertainty Quantification with Analytical Derivatives for Design Under Uncertainty

Uncertainty quantification (UQ) is a rapidly growing and evolving discipline, especially within the aerospace community. Performing analysis with UQ can provide decision makers with a wealth of information about a candidate design. However, the value of UQ is fully realized when the information gained during UQ analysis is leveraged in a feedback loop of a design optimization process, often referred to as design under uncertainty. Although design under uncertainty can be a powerful risk mitigation technique, there are a number of roadblocks that prevent its implementation. Two primary factors are computational costs and added complexity of the analysis. High fidelity simulations on the order tens of uncertain variables quickly become computationally infeasible. Also, implementing UQ into an existing multidisciplinary design and optimization (MDO) process often requires extensive knowledge of the UQ methods and careful treatment of the problem formulation. The objective of this work is to address these two primary roadblocks and enable practitioners to efficiently perform design under uncertainty with limited knowledge of the UQ discipline. Methods outlined in this paper demonstrate MDO incorporating UQ into the design process, leveraging an analytic derivative tool chain through the entire optimization. The proposed approach leverages machine learning techniques to generate a differentiable confidence interval output from polynomial chaos models. This technique, coupled with the incorporation of analytical derivatives through the Polynomial Chaos Expansion (PCE) process, eliminates the need to estimate derivatives which are usually obtained from finite difference, complex step, or similar methods. Developing a differentiable confidence interval allows mixed uncertainty problems (both epistemic and aleatory) to be modeled. Without such modeling, these problems cannot accurately predict objective functions containing statistical quantities such as mean and variance. The addition of analytic derivatives to a polynomial chaos-based UQ method decreases the computational costs of performing design under uncertainty by orders of magnitude in comparison with methods such as complex step. The method and codes developed are modular in nature and are a drop-in solution for design under uncertainty within existing MDO problems. A low-fidelity analytical multidisciplinary optimization under uncertainty for a wing design in OpenMDAO is detailed in this paper. This demonstration case will include both objective functions and constraints which are influenced by uncertain parameters.

Ben D Phillips↗

NASA NTRSDate not supplied

End-To-End Uncertainty Quantification with Analytical Derivatives for Design Under Uncertainty

Uncertainty quantification (UQ) is a rapidly growing and evolving discipline, especially within the aerospace community. Performing analysis with UQ can provide decision makers with a wealth of information about a candidate design. However, the value of UQ is fully realized when the information gained during UQ analysis is leveraged in a feedback loop of a design optimization process, often referred to as design under uncertainty. Although design under uncertainty can be a powerful risk mitigation technique, there are a number of roadblocks that prevent its implementation. Two primary factors are computational costs and added complexity of the analysis. High fidelity simulations on the order tens of uncertain variables quickly become computationally infeasible. Also, implementing UQ into an existing multidisciplinary design and optimization (MDO) process often requires extensive knowledge of the UQ methods and careful treatment of the problem formulation. The objective of this work is to address these two primary roadblocks and enable practitioners to efficiently perform design under uncertainty with limited knowledge of the UQ discipline. Methods outlined in this paper demonstrate MDO incorporating UQ into the design process, leveraging an analytic derivative tool chain through the entire optimization. The proposed approach leverages machine learning techniques to generate a differentiable confidence interval output from polynomial chaos models. This technique, coupled with the incorporation of analytical derivatives through the Polynomial Chaos Expansion (PCE) process, eliminates the need to estimate derivatives which are usually obtained from finite difference, complex step, or similar methods. Developing a differentiable confidence interval allows mixed uncertainty problems (both epistemic and aleatory) to be modeled. Without such modeling, these problems cannot accurately predict objective functions containing statistical quantities such as mean and variance. The addition of analytic derivatives to a polynomial chaos-based UQ method decreases the computational costs of performing design under uncertainty by orders of magnitude in comparison with methods such as complex step. The method and codes developed are modular in nature and are a drop-in solution for design under uncertainty within existing MDO problems. A low-fidelity analytical multidisciplinary optimization under uncertainty for a wing design in OpenMDAO is detailed in this paper. This demonstration case will include both objective functions and constraints which are influenced by uncertain parameters.

Ben Phillips↗

NASA NTRSDate not supplied

Latest Development in Radiative Transfer Models and Retrieval Algorithms Using Principal Components

The radiative transfer model (RTMs) has a wide range of applications in satellite remote sensing and atmospheric radiation applications. However, millions of line-by-line (LBL) radiative transfer calculations at fine monochromatic frequencies are needed in order to properly calculate spectral contributions of water vapor and trace gases in the atmosphere in infrared and solar spectral regions. Therefore, fast and accurate RTMs are needed to efficiently process large amount of satellite data. A Principal Component-based Radiative Transfer Model (PCRTM) was first developed in 2004 at NASA Langley Research Centre to fulfil this need. By using PC-compression, one can reduce the data dimension significantly while maintaining original information content. The PCRTM can directly compute PC-scores and their derivatives with respect to retrieved parameters. The PCRTM can simulate the top-of-atmosphere (TOA) radiance or reflectance spectra from 0.250 µm (400000 cm-1) to 2000 µm (50 cm-1) with several orders of magnitude faster speed as compared to a LBL RTM. It is also extremely accurate compared to LBL RTM benchmarks (0.03 K RMS error in IR and 0.05% in solar). The PCRTM model has been developed for hyperspectral sensors such as AIRS, CrIS, IASI, NAST-I, SHIS, FIRST, and CLARREO-IR in thermal IR spectral region and CLARREO-Solar, CPF, TEMPO, EMIT, OMI, and SCIAMACHY in solar spectral region. The PCRTM accuracy has been demonstrated via RTM intercomparisons and with real satellite observations from AIRS, CrIS, IASI, SCHIAMACHY, and EMIT etc. In this presentation, we will describe two PCRTM-based inversion algorithms to retrieve atmospheric temperature, water vapor, and trace gas profiles, as well as cloud and surface properties from hyperspectral sounders such as AIRS, CrIS, IASI, and NAST-I. The first one is called Single Fieldof-view Sounder Atmospheric Product (SiFSAP) algorithm. It provides L2 products with 9-times higher area spatial resolution as compared to current cloud-clearing sounder algorithms. The SiFSAP L2 and L3 products are available at NASA's Goddard Earth Sciences Data and Information Services Center (GES DISC) for public access. The second inversion algorithm is called Climate Fingerprinting Atmospheric Product (ClimFiSP) algorithm. It is designed to produce high quality climate products (trends, anomalies, daily, and monthly profiles of temperature, water vapor, traces, clouds, and surface properties) from multiple satellite sensors such AIRS on Aqua and CrIS on multiple satellites. This product will be available at NASA GES DISC later this year. The PCRTMbased high fidelity simulators for CLARREO and CPF have been used for sensor performance trade studies, algorithm development, and inter-satellite calibrations. We have also used PCRTM generated TOA radiance spectra to train an AI-based algorithm and successfully retrieved cloud properties from EMIT solar hyperspectral imagers.

PCRTM↗

NASA NTRS1977

A comparison of washout filters using a human dynamic orientation model

The Ormsby model of human dynamic orientation, a discrete time computer program, was used to provide a vestibular explanation for observed differences between two washout schemes. These washout schemes, a linear washout and a nonlinear washout, were subjectively evaluated. It was found that the linear washout presented false rate cues, causing pilots to rate the simulation fidelity of the linear scheme much lower than the nonlinear scheme. By inputting these motion histories into the Ormsby model, it was shown that the linear filter causes discontinuities in the pilot's perceived angular velocity, resulting in the sensation of an anomalous rate cue. This phenomenon does not occur with the use of the nonlinear filter.

Riedel, S. A.↗

NASA NTRS1978

Optimal regulator or conventional? Setup techniques for a model following simulator control system

Optimal regulator technique was compared for determining simulator control system gains with the conventional servo analysis approach. Practical considerations, associated with airborne motion simulation using a model-following system, provided the basis for comparison. The simulation fidelity specifications selected were important in evaluating the relative advantages of the two methods. Frequency responses for a JetStar aircraft following a roll mode model were calculated digitally to illustrate the various cases. A technique for generating forward loop lead in the optimal regulator model-following problem was developed which increases the flexibility of that approach. It appeared to be the only way in which the optimal regulator method could meet the fidelity specifications.

Deets, D. A.↗

NASA NTRS1978

V/STOL aircraft simulation - Requirements and capabilities at Ames Research Center

Ground-based flight simulation contributes greatly to the development of new aircraft and flight management systems and will be especially important in improving the performance, safety, and environmental characteristics of future civil and military V/STOL aircraft. This paper describes existing simulation facilities at Ames Research Center and discusses their capabilities and limitations for V/STOL aircraft investigations. Simulation requirements for NASA research and support of DOD programs are also discussed, including technology development for advanced rotorcraft and civil and military V/STOL aircraft. Current efforts and future plans are described for the upgrading of Ames simulation facilities to meet those requirements. Recent advances in equipment technology and operational methodology are shown to provide significantly improved simulation fidelity through better motion and visual cues and faster system response to pilot inputs.

Wilcox, D. E.↗

NASA NTRS1979

Determination of ASPS performance for large payloads in the shuttle orbiter disturbance environment

A high fidelity simulation of the annular suspension and pointing system (ASPS), its payload, and the shuttle orbiter was used to define the worst case orientations of the ASPS and its payload for the various vehicle disturbances, and to determine the performance capability of the ASPS under these conditions. The most demanding and largest proposed payload, the Solar Optical Telescope was selected for study. It was found that, in all cases, the ASPS more than satisfied the payload's requirements. It is concluded that, to satisfy facility class payload requirements, the ASPS or a shuttle orbiter free-drift mode (control system off) should be utilized.

Keckler, C. R.↗

NASA NTRS1981

Recent Progress Towards Predicting Aircraft Ground Handling Performance

The significant progress which has been achieved in development of aircraft ground handling simulation capability is reviewed and additional improvements in software modeling identified. The problem associated with providing necessary simulator input data for adequate modeling of aircraft tire/runway friction behavior is discussed and efforts to improve this complex model, and hence simulator fidelity, are described. Aircraft braking performance data obtained on several wet runway surfaces is compared to ground vehicle friction measurements and, by use of empirically derived methods, good agreement between actual and estimated aircraft braking friction from ground vehilce data is shown. The performance of a relatively new friction measuring device, the friction tester, showed great promise in providing data applicable to aircraft friction performance. Additional research efforts to improve methods of predicting tire friction performance are discussed including use of an instrumented tire test vehicle to expand the tire friction data bank and a study of surface texture measurement techniques.

Yager, T. J.↗

NASA NTRS1981

Recent progress towards predicting aircraft ground handling performance

Capability implemented in simulating aircraft ground handling performance is reviewed and areas for further expansion and improvement are identified. Problems associated with providing necessary simulator input data for adequate modeling of aircraft tire/runway friction behavior are discussed and efforts to improve tire/runway friction definition, and simulator fidelity are described. Aircraft braking performance data obtained on several wet runway surfaces are compared to ground vehicle friction measurements. Research to improve methods of predicting tire friction performance are discussed.

Yager, T. J.↗

NASA NTRS1982

Development of electrical test procedures for qualification of spacecraft against EID. Volume 1: The CAN test and other relevant data

A combined experimental and analytical program to develop system electrical test procedures for the qualification of spacecraft against damage produced by space-electron-induced discharges (EID) occurring on spacecraft dielectric outer surfaces is described. The data on the response of a simple satellite model, called CAN, to electron-induced discharges is presented. The experimental results were compared to predicted behavior and to the response of the CAN to electrical injection techniques simulating blowoff and arc discharges. Also included is a review of significant results from other ground tests and the P78-2 program to form a data base from which is specified those test procedures which optimally simulate the response of spacecraft to EID. The electrical and electron spraying test data were evaluated to provide a first-cut determination of the best methods for performance of electrical excitation qualification tests from the point of view of simulation fidelity.

Wilkenfeld, J. M.↗

NASA NTRS1983

Frequency-domain identification of XV-15 tilt-rotor aircraft dynamics

Frequency-domain methods are used to identify the open-loop dynamics of the XV-15 tilt-rotor aircraft from flight tests. Piloting and data analysis techniques are presented to determine frequency response plots and equivalent transfer function models. The open-loop pitch and roll dynamics for the hover flight condition exhibit unstable low-frequency oscillations, whereas the dynamics in the remaining degrees of freedom are lightly damped and generally decoupled. Comparisons of SV-13 flight-test and simulator data are more favorable for high-frequency inputs (omega greater than 1.0 rad/sec) than low-frequency inputs. The identification of symmetric and asymmetric beam-bending modes compares favorably with previous flight-test data. The results presented in this paper demonstrate the utility of the frequency-domain techniques for dynamics identification and simulator fidelity studies.

Tischler, M. B.↗

NASA NTRS1983

Quantification of crew workload imposed by communications-related tasks in commercial transport aircraft

Information theoretic analysis and subjective paired-comparison and task ranking techniques were employed in order to scale the workload of 20 communications-related tasks frequently performed by the captain and first officer of transport category aircraft. Tasks were drawn from taped conversations between aircraft and air traffic controllers (ATC). Twenty crewmembers performed subjective message comparisons and task rankings on the basis of workload. Information theoretic results indicated a broad range of task difficulty levels, and substantial differences between captain and first officer workload levels. Preliminary subjective data tended to corroborate these results. A hybrid scale reflecting the results of both the analytical and the subjective techniques is currently being developed. The findings will be used to select representative sets of communications for use in high fidelity simulation.

Acton, W. H.↗

NASA NTRS1984

A modal reduction method for use with nonlinear simulations of flexible multibody spacecraft

This paper presents a modal truncation method that can be used to prepare the structural flexibility data required as input to flexible, multibody spacecraft simulation programs. The method allows one to truncate the structural models of each flexible body in the system such that the assembled system is free of undesired high frequency system modes. This truncation method enables reasonable simulation costs to be incurred while maintaining dynamic simulation fidelity in the frequency range of interest. A simple one-dimensional example is presented which provides a physical interpretation of the method's workings. In addition, results are presented from the application of the method to a complex spacecraft.

Macala, G. A.↗

NASA NTRS1985

The influence of sampling rate on the dynamics and control of aeronautical systems

It is shown in the design of aeronautical control systems that sampling rate variations give rise to migrations of the discrete eigenvalues for both the plant and the controllers. In general, these migrations tend to degrade simulation fidelity and the overall performance of Ultrareliable Fault Tolerant Control Systems (UFTCS). These systems consist of a redundant asynchronous network of microprocessors which use sensor information to generate the servo commands that drive actuators, thrust linkages, etc. A change in the sampling period of a single microprocessor will, in addition to causing an eigenvalue shift, alter the magnitude of the servo command issued by the controller. The influence of these changes and the effect of initial conditions and skew are considered.

Howard, J. C.↗

NASA NTRS1987

Prototype space station automation system delivered and demonstrated at NASA

The Automated Subsystem Control for Life Support System (ASCLSS) program has successfully developed and demonstrated a generic approach to the automation and control of Space Station subsystems. The hierarchical and distributed real time controls system places the required controls authority at every level of the automation system architecture. As a demonstration of the automation technique, the ASCLSS system automated the Air Revitalization Group (ARG) of the Space Station regenerative Environmental Control and Life Support System (ECLSS) using real-time, high fidelity simulators of the ARG processess. This automation system represents an early flight prototype and an important test bed for evaluating Space Station controls technology including future application of ADA software in real-time control and the development and demonstration of embedded artificial intelligence and expert systems (AI/ES) in distributed automation and controls systems.

Block, Roger F.↗

NASA NTRS1987

Multimodal user input to supervisory control systems - Voice-augmented keyboard

The use of a voice-augmented keyboard input modality is evaluated in a supervisory control application. An implementation of voice recognition technology in supervisory control is proposed: voice is used to request display pages, while the keyboard is used to input system reconfiguration commands. Twenty participants controlled GT-MSOCC, a high-fidelity simulation of the operator interface to a NASA ground control system, via a workstation equipped with either a single keyboard or a voice-augmented keyboard. Experimental results showed that in all cases where significant performance differences occurred, performance with the voice-augmented keyboard modality was inferior to and had greater variance than the keyboard-only modality. These results suggest that current moderately priced voice recognition systems are an inappropriate human-computer interaction technology in supervisory control systems.

Mitchell, Christine M.↗

NASA NTRS1988

The development of an automated flight test management system for flight test planning and monitoring

The development of an automated flight test management system (ATMS) as a component of a rapid-prototyping flight research facility for AI-based flight systems concepts is described. The rapid-prototyping facility includes real-time high-fidelity simulators, numeric and symbolic processors, and high-performance research aircraft modified to accept commands for a ground-based remotely augmented vehicle facility. The flight system configuration of the ATMS includes three computers: the TI explorer LX and two GOULD SEL 32/27s.

Hewett, Marle D.↗