Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Acoustic Measurements for Small Solid Rocket Motors

Models have been developed to predict large solid rocket motor acoustic loads based on the scaling of small solid rocket motors. MSFC has measured several small solid rocket motors in horizontal and launch configurations to anchor these models. Solid Rocket Test Motor (SRTM) has ballistics similar to the Reusable Solid Rocket Motor (RSRM) therefore a good choice for acoustic scaling. Acoustic measurements were collected during the test firing of the Insulation Configuration Extended Length (ICXL) 7,6, and 8 (in firing order) in order to compare to RSRM horizontal firing data. The scope of this presentation includes: Acoustic test procedures and instrumentation implemented during the three SRTM firings and Data analysis method and general trends observed in the data.

Vargas, Magda B.↗
NASA NTRS2010

Solid expellant plasma generator

An improved solid expellant plasma generator has been developed. The plasma generator includes a support housing, an electrode rod located in the central portion of the housing, and a mass of solid expellant material that surrounds the electrode rod within the support housing. The electrode rod and the solid expellant material are made of separate materials that are selected so that the electrode and the solid expellant material decompose at the same rate when the plasma generator is ignited. This maintains a point of discharge of the plasma at the interface between the electrode and the solid expellant material.

Stone, Nobie H.↗
NASA NTRS2011

Photolysis of Pure Solid O3 and O2 Films at 193nm

We studied quantitatively the photochemistry of solid O3 and O2 films at 193 nm and 22 K with infrared spectroscopy and microgravimetry. Photolysis of pure ozone destroyed O3, but a small amount of ozone remained in the film at high fluence. Photolysis of pure O2 produced O3 in an amount that increased with photon fluence to a stationary level. For both O2 and O3 films, the O3:O2 ratio at large fluences is ?0.07, about two orders of magnitude larger than those obtained in gas phase photolysis. This enhancement is attributed to the increased photodissociation of O2 due to photoabsorption by O2 dimers, a process significant at solid-state densities. We obtain initial quantum yield for ozone synthesis from solid oxygen, phi (O3) = 0.24 0.06, and quantum yields for destruction of O3 and O2 in their parent solids, phi(-O3) = 1.0 0.2 and phi(-O2) = 0.36 0.1. Combined with known photoabsorption cross sections, we estimate probabilities for geminate recombination of 0.5 0.1 for O3 fragments and 0.88 0.03 for oxygen atoms from O2 dissociation. Using a single parameter kinetic model, we deduce the ratio of reaction cross sections for an O atom with O2 vs. O3 to be 0.1 0.2. The general good agreement of the model with the data suggests the validity of the central assumption of efficient energy and spin relaxation of photofragments in the solid prior to their reactions with other species.

Raut, U.↗
NASA NTRS2014

CO Self-Shielding as a Mechanism to Make O-16 Enriched Solids in the Solar Nebula

Photochemical self-shielding of CO has been proposed as a mechanism to produce solids observed in the modern, O-16 depleted solar system. This is distinct from the relatively O-16 enriched composition of the solar nebula, as demonstrated by the oxygen isotopic composition of the contemporary sun. While supporting the idea that self-shielding can produce local enhancements in O-16 depleted solids, we argue that complementary enhancements of O-16 enriched solids can also be produced via CO-16 based, Fischer-Tropsch type (FTT) catalytic processes that could produce much of the carbonaceous feedstock incorporated into accreting planetesimals. Local enhancements could explain observed O-16 enrichment in calcium-aluminum-rich inclusions (CAIs), such as those from the meteorite, Isheyevo (CH/CHb), as well as in chondrules from the meteorite, Acfer 214 (CH3). CO selfshielding results in an overall increase in the O-17 and O-18 content of nebular solids only to the extent that there is a net loss of CO-16 from the solar nebula. In contrast, if CO-16 reacts in the nebula to produce organics and water then the net effect of the self-shielding process will be negligible for the average oxygen isotopic content of nebular solids and other mechanisms must be sought to produce the observed dichotomy between oxygen in the Sun and that in meteorites and the terrestrial planets. This illustrates that the formation and metamorphism of rocks and organics need to be considered in tandem rather than as isolated reaction networks.

Solar Nebula↗
NASA NTRS2015

Solid-State Cloud Radar System (CRS) Upgrade and Deployment

The recent decade has brought rapid development in solid-state power amplifier (SSPA) technology. This has enabled the use of solid-state precipitation radar in place of high-power and high-voltage systems such as those that use Klystron or Magnetron transmitters. The NASA Goddard Space Flight Center has recently completed a comprehensive redesign of the 94 gigahertz Cloud Radar System (CRS) to incorporate a solid-state transmitter. It is the first cloud radar to achieve sensitivity comparable to that of a high-voltage transmitter using solid-state. The NASA Goddard Space Flight Center's Cloud Radar System (CRS) is a 94 gigahertz Doppler radar that flies on the NASA ER-2 high-altitude aircraft. The upgraded CRS system utilizes a state-of-the-art solid-state 94 gigahertz power amplifier with a peak transmit power of 30 watts. The modernized CRS system is detailed here with data results from its deployment during the 2014 Integrated Precipitation and Hydrology Experiment (IPHEX).

Radar Radiometer Sampling↗
NASA NTRS2016

Development Status for a Combined Solid Oxide Co-Electrolyzer and Carbon Formation Reactor System for Oxygen Regeneration

A critical component in spacecraft life support loop closure is the removal of carbon dioxide (CO2, produced by the crew) from the cabin atmosphere and chemical reduction of this CO2 to recover the oxygen. In 2015, we initiated development of an oxygen recovery system for life support applications consisting of a solid oxide co-electrolyzer (SOCE) and a carbon formation reactor (CFR). The SOCE electrolyzes a combined stream of carbon dioxide (CO2) and water (H2O) gas mixtures to produce synthesis gas (e.g., CO and H2 gas) and pure dry oxygen as separate products. This SOCE is being developed from a NASA GRC solid oxide fuel cell and stack design originally developed for aeronautics long-duration power applications. The CFR, being developed by pHMatter LLC, takes the CO and H2 output from the SOCE, and converts it primarily to solid carbon (C(s)) and H2O and CO2. Although the solid carbon accumulates in the CFR, the innovative design allows easy removal of the carbon product, requiring minimal crew member (CM) time and low resupply mass (1.0 kg/year/CM) for replacement of the solid carbon catalyst, a significant improvement over previous Bosch reactor approaches. In this work, we will provide a status of our Phase I efforts in the development and testing of both the SOCE and CFR prototype units, along with an initial assessment of the combined SOCE-CFR system, including a mass and power projections, along with an estimate of the oxygen recovery rate.

air revitalization↗
NASA NTRS2019

Specific Impulse of Electric Solid Propellant in an Electrothermal Ablation-Fed Pulsed Plasma Thruster

Electric solid propellants are advanced solid chemical rocket propellants that can be controlled (ignited, throttled, and extinguished) through the application and removal of an electric current. Recent work has focused on application of this propellant in an electrothermal ablation-fed pulsed plasma thruster. In this paper, impulse bit measurements in such devices fed by either the electric solid propellant or a traditional state-of-the-art propellant, polytetrafluoroethylene, are expanded upon. It is demonstrated that a surface layer in the hygroscopic electric solid propellant is rapidly ablated over the first few discharges of the device, which correspondingly decreases specific impulse relative to the traditional polytetrafluoroethylene propellant. Correcting these data by subtracting the early discharge ablation mass loss measurements yields a corrected electric solid propellant specific impulse of approximately 300 s. As the test duration increases to a large number of discharges, and the initial mass loss is a reduced fraction of the total, the effect of absorbed water in the propellant is decreased and the specific impulse without any corrections approaches the corrected 300 s value.

Glascock, Matthew S.↗
NASA NTRSDate not supplied

Extinction of the Stagnation Point Diffusion Flame: Effect of Conductive Heat Loss into Solid Interior

The planned microgravity experiment Growth and Extinction Limit (GEL) is designed to study the material flammability and extinction of thermally thick solid with an emphasis to quantify the effect of conductive heat loss into the solid interior by measuring the in-depth temperature profile. To obtain a more detailed understanding of the extinction phenomena, a previously developed one-dimensional axisymmetric stagnation-point diffusion flame model is expanded to account for the excessive heat loss into the solid beyond the steady burning state. This is important because for thick solids, this is important because the burning period can have a long and slow solid transient with a quasi-steady gas -phase. A non-dimensional excessive conductive heat loss parameter Ψ is defined in the paper and extensive numerical computations have been performed to determine the extinction boundary and the characteristics of near-limit flames. The classical U-shaped flammability boundary in the oxygen vs. stretch rate plot now becomes a series of U-shaped boundaries as a function of Ψ. For a given oxygen ambient, extinction boundary is a function of Ψ. The boundary consists of a blowoff branch and a radiative quenching branch. This is similar to the steady burning flammability boundary (Ψ =0) in the oxygen vs stretch rate plot. Extensive computed data including flame and pyrolysis temperatures, burning rate, flame standoff distance, and reaction rate are presented along the extinction boundaries. In particular, we note that the non-dimensional gas reaction rate is the ratio of diffusion reaction time to the reaction diffusion time, so it has the classical Damhkoler number character. By examining the maximum non-dimensional reaction rates, we observe that along the extinction boundaries, they are approximate constant across the entire range of stretch rates (from quenching to blow-off). These critical values are of the order unity but may vary in different oxygen ambient. The implication will be discussed in the presentation together with the near-limit flame structures.

Chengyao Li↗
DOE OSTI2024

Nasicon dual ion conductors for all solid-state batteries

A super ion conductor composition is disclosed. The super ion conductor composition has the general formula: A 1+x M x/2 Zr 2−x/2 (PO 4 ) 3 , where each A is independently Na or Li, M is Mn or Mg, and subscript x is from 0.5 to 3. A solid electrolyte comprising the super ion conductor composition, and a method of preparing the solid electrolyte, are also disclosed. The method comprises combining a zirconium compound, a manganese or magnesium compound, a sodium compound, and a phosphate compound to give a mixture; and calcining the mixture to give the super ion conductor composition, thereby preparing the solid electrolyte. Functional materials and devices comprising the super ion conductor composition are also disclosed, including a catholyte composition, an ion conducting solid electrolyte membrane, as well as all-solid-state batteries.

Amin, Ruhul↗
DOE OSTI2025

Low-temperature liquid-phase synthesis of lithium thiophosphate-borohydride solid electrolyte with high room-temperature ionic conductivity

Embodiments relate to a scalable liquid-phase synthesis technique of lithium thiophosphate-borohydride solid electrolytes with high ionic conductivity at room temperature and its use in all-solid-state lithium batteries. A battery comprises an anode, a cathode, and a solid electrolyte layer positioned between the anode and the cathode. The liquid-phase synthesized solid electrolyte material can be used as the solid electrolyte layer or incorporated into anodes or cathodes.

Wang, Donghai [Pennsylvania State Univ., Universit↗
DOE OSTI2024

Tailoring Binder Molecular Weight to Enhance Slurry-Cast NMC Cathodes for Sulfide Solid-State Batteries

We demonstrate for the first time the critical influence of binder molecular weight on the performance of slurry-cast lithium nickel manganese cobalt oxide (NMC) cathodes in sulfide-based all-solid-state batteries (SSBs). SSBs are increasingly recognized as a safer and potentially more efficient alternative to traditional Li-ion batteries, owing to the superior ionic conductivities and inherent safety features of sulfide solid electrolytes. However, the integration of high-voltage NMC cathodes with sheet-type sulfide solid electrolytes presents significant fabrication challenges. Our findings reveal that higher molecular weight binders not only enhance the discharge capacity and cycle life of these cathodes but also ensure robust adhesion and structural integrity. By optimizing binder molecular weights, we effectively shield the active materials from degradation and mechanical stress, significantly boosting the functionality and longevity of SSBs. These results underscore the paramount importance of binder properties in advancing the practical application of high-performance all-solid-state batteries.

25 ENERGY STORAGE↗
NASA NTRSDate not supplied

Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Sustainable Electric Aviation

All-electric and hybrid electric aerovehicle concepts face numerous technical barriers prior to their introduction into the consumer marketplace in order to meet sustainable aviation goals. One of the primary barriers to overcome is developing an energy dense storage system capable of meeting the rigorous aerospace safety and performance criteria. Additionally, the electric aviation market requires that the batteries be fabricated in a sustainable manner with materials that are readily available and abundant within the U.S. to ensure there are no supply chain issues during manufacturing. The performance metrics to enable electric aviation are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. The hybrid cathode has been developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte has been used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This poster summarizes recent results from battery component optimization to scale-up production of full SABERS pouch cells.

Urban Air Mobility (UAM) Vehicles↗
DOE OSTI2026

Revealing the Roles of CuF 2 /NiF 2 Incorporation in the Electrochemical Performance of FeF 3 Cathodes in Solid‐State Batteries

Mixed metal fluorides have been considered as a promising candidate to lower the voltage hysteresis of conversion-type iron fluoride cathodes, but their cycling stability is limited due to transition metal dissolution and interphase growth in liquid electrolyte batteries. Here, we study the role of incorporating CuF 2 and NiF 2 in the electrochemical performance of FeF 3 cathode in halide-based solid-state batteries to test whether we can transfer the kinetic benefit of low voltage hysteresis to solid-state batteries while using solid electrolyte to eliminate transition metal dissolution and stabilize the interphase. Synchrotron X-ray absorption spectroscopy results indicated the redox reactions are attributed to Cu 0 /Cu + and Fe 0 /Fe 2+ in 25CuF 2 -75FeF 3 and Ni 0 /Ni 2+ and Fe 0 /Fe 3+ in 10NiF 2 -90FeF 3 . While no apparent improvement in electrode kinetics can be observed, the incorporation of CuF 2 and NiF 2 can largely improve the cycling stability of FeF 3 cathodes. In conclusion, the results demonstrate the advantages of using solid-state concept to improve the cycling stability of conversion-type cathodes.

25 ENERGY STORAGE↗
DOE OSTI2026

All‐Solid‐State Batteries With Mechanically Stable Interfaces Consisting of a Zero‐Strain Cation‐Disordered Rocksalt Cathode

Interface stabilization is critical to the development of working all‐solid‐state batteries. Rigid cathode/solid electrolyte interfaces often disintegrate due to anisotropic volume change of cathode‐active materials, resulting in irreversible capacity loss. Herein, we demonstrate that Li 1.211 Mo 0.467 Cr 0.3 O 2 (LMCO), a pioneering cation‐disordered rocksalt oxide (DRX) cathode that has intrinsically small volume change upon lithium intercalation, can be integrated with a thiophosphate‐based solid electrolyte for all‐solid‐state batteries. Interface stability of the all‐solid LMCO cell was investigated by electrochemical impedance spectroscopy, X‐ray micro‐computed tomography, and electron microscopy. Since LMCO was initially synthesized as a layered phase exhibiting a large volume change, interface disintegration can be observable in the early cycles. As layered LMCO phase‐transformed into DRX LMCO in subsequent cycles, reintegration of the interfaces occurs within a pressurized cell as a result of its zero‐stain behavior. Consequently, the DRX LMCO cathode maintains interface integrity, and thus electrical wiring, over an extended number of cycles, leading to improved capacity retention with small internal cell resistance.

DRX↗
DOE OSTI2025

Probing the Impact of Vacancy Diffusion on Void Dynamics at the Lithium Metal–Solid Electrolyte Interface

Lithium (Li) metal-based solid-state batteries (SSBs) are considered promising candidates for next-generation energy storage due to their superior energy density and enhanced safety compared to conventional Li-ion systems. However, their practical application is limited by challenges such as void formation at the Li-solid electrolyte (SE) interface, which disrupts ion transport and accelerates interfacial degradation. This work investigates how the coupled effects of electro-dissolution kinetics and surface diffusion at the Li metal surface govern the evolution of interfacial morphology during stripping. This work examines the influence of three distinct surface diffusion modes, which are terrace diffusion, step diffusion, and interlayer diffusion, on maintaining interfacial stability. In addition, how the dominant surface diffusion mechanism can overcome the contact loss due to high reaction kinetics is explored. Furthermore, the roughness of the Li metal anode surface is quantified, and the influence of different diffusion mechanisms on the evolution of the dynamic solid–solid interface is examined. The critical role of temperature in enhancing Li surface diffusivity and expanding the regime of stable contact is highlighted. By identifying distinct regimes of interface stability, this study analyzes how non-uniform electrochemical dynamics dictate void morphology evolution and interfacial contact. These insights offer guiding principles for engineering robust Li–SE interfaces in SSBs.

lithium metal anode↗
DOE OSTI2025

A Poromechanical Framework for Internal Interactions Induced by Solid Inclusions

The framework of poromechanics is generalized to simulate the multiscale behavior of porous media subjected to internal loadings stemming from the growth of solid inclusions. This generalization is designed to enable the study of anisotropic internal stress generation from solid growth within the pores, while recovering isotropic fluid-induced loading as a particular case. For this purpose, a mathematical strategy to define constitutive tensors in a thermodynamically consistent form is proposed, thus offering new opportunities for determining the poromechanical properties of a porous solid through advanced experimentation or micromechanical models. The framework is specialized by means of established elastic solutions for single pore–matrix interaction, as well as through homogenization schemes considering the interaction among congruent pores. In particular, the second Eshelby solution and the Tanaka–Mori–Benveniste homogenization scheme are used to derive a microporoelastic model. At an elemental scale, the model is tested under mixed control conditions by replicating different scenarios of geomaterial testing. In addition, the model characteristics are outlined with reference to inelastic microscopic loadings replicating chemo-mechanical forcing, such as expansive crystal formation. Through a series of parametric analyses, it is shown that the microstructure of the pores significantly influences the properties of porous media. Most notably, it is shown that the effects of a solid forming within the pores depend in a highly nonlinear fashion on the constitutive characteristics of the inhomogeneities and can therefore not be readily quantified or predicted without models capturing the diverse multiscale interactions among pores, inhomogeneities, and matrix.

chemomechanics↗
DOE OSTI2025

Optimizing the impacts of solid additives on the operational stability and processing reliability of organic solar cells

Previous reports have revealed that by leveraging solid additives, organic solar cells (OSCs) can surpass the device’s performance beyond the intrinsic limitations of host photoactive molecules, a remarkable advancement. However, the impacts of more complex interactions introduced by solid additives are not yet well understood. Herein, optimizing the fabrication process based on the traditional efficiency-guided approach fails to represent the ideal and most practical devices. In particular, achieving superior operational stability while minimizing the device performance scattering was found to require processing solvent evaporation to be synchronized with the volatility of the chosen solid additive. However, this may be challenging since most organic photoactive materials display excellent efficiencies only with selected solvents. Accordingly, this work also demonstrates the potential of dual and complementary solvents selection, consisting of low boiling point (primary) and high boiling point (secondary). This strategy allows for the suppression of any potential trade-offs in efficiency. Meanwhile, the operational stability and precision of device performance are substantially enhanced. Additionally, solid additives have demonstrated that the singlet exciton dissociation rate does not limit the free charge generation yield. Finally, these findings are expected to reformulate OSC device fabrication strategies towards more practical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tuning collective anion motion enables superionic conductivity in solid-state halide electrolytes

Halides of the family Li 3 MX 6 (M = Y, In, Sc and so on, X = halogen) are emerging solid electrolyte materials for all-solid-state Li-ion batteries. They show greater chemical stability and wider electrochemical stability windows than existing sulfide solid electrolytes, but have lower room-temperature ionic conductivities. Here, in this work, we report the discovery that the superionic transition in Li 3 YCl 6 is triggered by the collective motion of anions, as evidenced by synchrotron X-ray and neutron scattering characterizations and ab initio molecular dynamics simulations. Based on this finding, we used a rational design strategy to lower the transition temperature and thus improve the room-temperature ionic conductivity of this family of compounds. We accordingly synthesized Li 3 YCl x Br 6-x and Li 3 GdCl 3 Br 3 and achieved very high room-temperature conductivities of 6.1 and 11 mS cm -1 for Li 3 YCl 4.5 Br 1.5 and Li 3 GdCl 3 Br 3 , respectively. These findings open new routes to the design of room-temperature superionic conductors for high-performance solid batteries.

25 ENERGY STORAGE↗