SEARCH · Search NASA

Results for “Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Imparting strength and toughness to brittle composites

Appropriate intermittent coatings of fibers can produce areas of low and high toughness in brittle composites. Experiments using silicon vacuum grease (SVG) and polyurethane varnish (PUV) coatings that achieve weakly and strongly bonded interfaces are described. Tensile strength and edge-crack fracture toughness for both SVG and PUV coatings were plotted against the percentage coating (C). Both coating materials maintain tensile strengths in the order of the rule of mixture strength values up to a large C. It is suggested that both materials produce similar coated interfacial shear strengths while producing different effects on toughness.

Atkins, A. G.↗

NASA NTRS1976

Cesium oscillator strengths measured with a multiple-path-length absorption cell

Absorption-oscillator-strength measurements for the principal series in cesium were measured using a multiple-path-length cell. The optical arrangement included a movable transverse path for checking the uniformity of the alkali density along the length of the cell and which also allowed strength measurements to be made simultaneously on both strong and weak lines. The strengths measured on the first 10 doublets indicate an increasing trend in the doublet ratio. The individual line strengths are in close agreement with the high resolution measurements of Pichler (1974) and with the calculations of Norcross (1973).

Exton, R. J.↗

NASA NTRS1976

Effect of Low Velocity Impact Damage on the Compressive Strength of Graphite/Epoxy Hat-Stiffened Panels

Low velocity impact damage on the compressive strength of graphite/epoxy hat stiffened panels is studied. Fourteen panels, representative of minimum-mass designs for two compression load levels were tested. Eight panels were damaged by impact and the effect on compressive strength was evaluated by comparing the results with data for undamaged panels. The impact tests consisted of firing 1.27 cm diameter aluminum projectiles normal to the plane of the panel at a velocity of approximately 55 m/sec to simulate impact from runway debris. The results of this investigation indicate that impact damage in the panels designed for 0.53 MN/m was contained locally and the damaged panels were capable of carrying the design load. The panels designed for 1.58 MN/m failed between 50 and 58 percent of the design load due to impact damage in the high axial stiffness region. The extent of damage in the high axial stiffness region of both panel designs increased with the magnitude of applied axial load. Damage in this region was the most significant factor in reducing panel strength. Limited damage that was not visually detectable reduced ultimate strength as much as extensive visible damage.

Rhodes, M. D.↗

NASA NTRS1976

Absolute oscillator strengths for the iron group - A correction to the data of Warner for the second spectra and a comment on some of the semiempirical results of Kurucz and Peytremann

It has already been shown that the Fe II absolute oscillator strengths (f-values) measured by Warner (1967) contain a systematic error, the magnitude of which depends on the energy of the transition's upper level. The present paper demonstrates that this error affects all of Warner's oscillator strengths for the second spectra of the iron group and develops a correction formula for Warner's results. A comparison of the corrected f-values with other measured f-values for Ti II, V II, and Fe II indicates that the correction improves the usefulness of Warner's data and that the corrected f-values have no large systematic dependence on wavelength, level energy, or line strength. Solar abundances for iron-group elements computed using the original and corrected f-values are compared with recently suggested abundances, and it is found that the corrected f-values yield more consistent results. Semiempirical oscillator strengths calculated by Kurucz and Peytremann (1975) for Fe I, Ti II, and V II are also compared with measured data to evaluate the accuracy of the calculations. It is found that the absolute scales of these results are roughly correct, but some of them are subject to very large errors.

Smith, P. L.↗

NASA NTRS1978

Adhesive/cohesive strength of a ZrO2.1-2 w/o Y2O3/NiCrAIY thermal barrier coating

The room temperature adhesive/cohesive strength of a 0.05 cm thick ZrO2.12w/oY2O3/0.013 cm thick NiCrAlY thermal barrier coating system (TBC) was investigated. The weakest link was the oxide/NiCrAlY interface region with a strength of 6.2 MN/sq m. The fracture was about half cohesive oxide failure, half oxide/NiCrAlY adhesive failure and 1 percent cohesive NiCrAlY failure. The TBC failed in a similar manner in 950 C tensile and compression tests. The oxide stripped from the TBC had a cohesive strength of 24.6 MN/sq m. The NiCrAlY had a cohesive strength of 25.1 MN/sq m. The NiCrAlY and oxide failed primarily at interparticle boundaries.

Levine, S. R.↗

NASA NTRS1978

Thermal environment effects on strength and impact properties of boron-aluminum composites

A systematic study was conducted regarding the degradation of fracture strength and impact energy in commercial B-Al composites in both static and cyclic thermal environments. The composites used in the study contained approximately 50 vol % boron fibers, unidirectionally aligned in either a 6061 Al or 1100 Al matrix. The tensile strengths of the composites after 3000 thermal cycles as a function of upper cycle temperature are presented in graphs. The temperature at which the strengths of 6061 Al matrix, B-Al composites were significantly degraded after 3000 cycles was noticeably higher than that for the 1100 Al matrix composites. Static heating at 420 C resulted in no significant strength degradation for the 6061 Al matrix composites. In the case of 1100 matrix composites, some degradation was observed at 420 C but markedly less than in the composites cycled to 420 C.

Grimes, H. H.↗

NASA NTRS1979

The influence of microstructure on the strength of reaction bonded silicon nitride /RBSN/

The effect of the microstructure of reaction bonded silicon nitride on strength is examined. The morphologies of the various microconstituents (alpha-matte, beta-spikes, residual silicon and porosity) each play a role in determining the strength of the material. While density and hence percent porosity greatly affect strength, it is shown that the pore size and pore size distribution affect strength with equal importance. By minimizing the pore size and distribution and maximizing the alpha-beta ratio, a reaction bonded material (2.4 kg/cu m) has been produced with a room temperature modulus of rupture (three-point bending) of 297 MPa from a low green density starting material (1.5 kg/cu m).

Danforth, S. C.↗

NASA NTRS1979

Effects of moisture on apparent flexure strength and on torsion and flexure fatigue properties of graphite-epoxy composites

The effects of moisture and temperature on unidirectional and multi-ply laminates of T300/934 and AS/3501 graphite-epoxy systems were investigated. Properties studied were static flexure strength and flexure and torsion fatigue strengths at room temperature and at 74 C. Specimens with increased moisture content showed a reduced static flexure strength; water as the test environment had only a negligible influence. In flexure fatigue and torsion fatigue, the water environment caused somewhat reduced fatigue strengths at room temperature and significantly greater degradation in 74 C water. The failure mode in all cases was interlaminar delamination.

Sumsion, H. T.↗

NASA NTRS1981

Correlation of ideal and actual shear strengths of metals with their friction properties

The relation between the ideal and actual shear strengths and friction properties of clean metals in contact with clean diamond, boron nitride, silicon carbide, manganese-zinc ferrite, and the metals themselves in vacuum is discussed. An estimate of the ideal shear strength for metals is obtained from the shear modulus, the repeat distance of atoms in the direction of shear of the metal, and the interplanar spacing of the shearing planes. The coefficient of friction for metals is shown to be correlated with both the ideal and actual shear strength of metals. The higher the strength of the metal, the lower the coefficient of friction occurs.

Miyoshi, K.↗

NASA NTRS1981

Experiment K307: Vertebral body strength of rat spinal columns

The effects of space flight on vertebral body bone strength excised were investigated. Comparative biomechanical investigations of vertebral body strength for flight, synchronous, and vivarium rats following spacecraft recovery (R+0), at R+6 and R+29 days post flight recovery are presented. Statistical analyses are presented for the mechanical properties of stiffness, ultimate load, displacement to ultimate load, and energy to ultimate load. At R+0 all of the above properties show that the vertebral body exhibits an increasing susceptibility to fracture. The reduction of bone strength is inhomogeneous and dependent on vertebral level. The R+6 recovery data was inconclusive since it varied above and below the R+0 data. At R+29 ultimate load values showed a statistically significant increase in bone strength approaching that of the vivarium or control group.

Kazarian, L. E.↗

NASA NTRS1981

Effect of load eccentricity and substructure deformation on ultimate strength of shuttle orbiter thermal protection system

The effect of load eccentricity and substructure deformation on the ultimate strength and stress displacement properties of the shuttle orbiter thermal protection system (TPS) was determined. The LI-900 Reusable Surface Insulation (RSI) tiles mounted on the .41 cm thick Strain Isolator Pad (SIP) were investigated. Substructure deformations reduce the ultimate strength of the SIP/tile TPS and increase the scatter in the ultimate strength data. Substructure deformations that occur unsymmetric to the tile can cause the tile to rotate when subjected to a uniform applied load. Load eccentricity reduces SIP/tile TPS ultimate strength and causes tile rotation.

Sawyer, J. W.↗

NASA NTRS1983

Measuring the Tensile Strength of B/AL Composites

Proposed nondestructive technique correlates damping measurements with material strength. Increasing axial damping and decreasing axial tensile strength are observed after 1-hour treatment of B/AL composites containing about 50 percent fiber. Damping was measured in vacuum at frequencies near 2,000 Hz, and tensile strength was normalized by maximum strength observed before thermally induced degradation.

Dicarlo, J. A.↗

NASA NTRS1982

Strength advantages of chemically polished boron fibers before and after reaction with aluminum

In order to determine their strength potential, the fracture properties of different types of commercial boron fibers were measured before and after application of secondary strengthening treatments. The principal treatments employed were a slight chemical polish, which removed low strength surface flaws, and a heat treatment in oxygen, which contracted the fibers and thereby compressed intrinsic bulk flaws. Those fiber types most significantly strengthened were 200 to 400 micrometers (8 to 16 mil) diameter boron on tungsten fibers produced in a single chemical vapor deposition reactor. The slight polish increased average tensile strenghts from 3.4 to 4.4 CN/m2 (500 to 640 ksi) and reduced coefficients of variation from about 15 to 3 percent. The oxygen heat treatment plus slight polish further improved average strengths to 5.5 GN/m2 (800 ksi) with coefficients near 3 percent. To ascertain whether these excellent properties could be retained after fabrication of B/Al composites, as produced and polished 203 micrometers (8 mil) fibers were thinly coated with aluminum, heat treated at B/Al fabrication temperatures, and then tested in tension and flexure at room temperature. The pre-polished fibers were observed to retain their superior strengths to higher temperatures than the as-produced fibers even though both were subjected to the same detrimental reaction with aluminum.

Dicarlo, J. A.↗

NASA NTRS1981

Strength distributions of SiC ceramics after oxidation and oxidation under load

The room-temperature strength distributions of a sintered and a hot-pressed SiC were examined as-machined, after oxidation at 1370 C, and after oxidation under load at 1370 C. The strengths were observed to be dependent on both the duration of oxidation and the magnitude of the applied load. Processes resulting in both strengthening and weakening behavior were observed to occur, at times simultaneously within the same strength distribution. This dynamic situation indicates that the strength-controlling flaw populations are highly transient in nature.

Easler, T. E.↗

NASA NTRS1982

Effects of oxidation and oxidation under load on strength distributions of Si3N4

The room-temperature strength distributions of a sintered and a hot-pressed Si3N4 were examined in the as-machined condition, after oxidation at 1370 C and after oxidation under load at 1370 C. The strength-controlling flaw populations were highly transient in nature. Both the duration of oxidation and the magnitude of the applied load were observed to effect changes in strength. This dynamic situation is related to both strengthening and weakening processes, which at times may occur simultaneously in the same strength distribution.

Easler, T. E.↗

NASA NTRS1982

Laboratory band strengths of methane and their application to the atmospheres of Jupiter, Saturn, Uranus, Neptune, and Titan. II - The red region 6000-7600 A

Lutz et al. (1976) have reported the first quantitative analyses of the strengths of the blue-green bands of methane which dominate the visible spectra of the outer planets. The present investigation represents an extension of the first study to include a number of bands between 6000 and 7500 A. The objective of this extension is to establish the validity of the scaled numerical curve of growth of the first study further into the saturated region and to test the apparent pressure independence of the high-overtone bands over a large pressure range. In addition, it is desired to provide a set of homogeneously determined band strengths and curves of growth over a large spectral region and over a large range of band strengths. This will make it possible to investigate feasible apparent dependences of planetary methane abundances on wavelength and band strength as a probe of the scattering processes in the planetary atmospheres.

Lutz, B. L.↗

NASA NTRS1983

Notch strength of composites

The notch strength of composites is discussed. The point stress and average stress criteria relate the notched strength of a laminate to the average strength of a relatively long tensile coupon. Tests of notched specimens in which microstrain gages have been placed at or near the edges of the holes have measured strains much larger that those measured in an unnotched tensile coupon. Orthotropic stress concentration analyses of failed notched laminates have also indicated that failure occurred at strains much larger than those experienced on tensile coupons with normal gage lengths. This suggests that the high strains at the edge of a hole can be related to the very short length of fiber subjected to these strains. Lockheed has attempted to correlate a series of tests of several laminates with holes ranging from 0.19 to 0.50 in. Although the average stress criterion correlated well with test results for hole sizes equal to or greater than 0.50 in., it over-estimated the laminate strength in the range of hole sizes from 0.19 to 0.38 in. It thus appears that a theory is needed that is based on the mechanics of failure and is more generally applicable to the range of hole sizes and the varieties of laminates found in aircraft construction.

Whitney, J. M.↗

NASA NTRS1983

The in situ transverse lamina strength of composite laminates

The objective of the work reported in this presentation is to determine the in situ transverse strength of a lamina within a composite laminate. From a fracture mechanics standpoint, in situ strength may be viewed as constrained cracking that has been shown to be a function of both lamina thickness and the stiffness of adjacent plies that serve to constrain the cracking process. From an engineering point of view, however, constrained cracking can be perceived as an apparent increase in lamina strength. With the growing need to design more highly loaded composite structures, the concept of in situ strength may prove to be a viable means of increasing the design allowables of current and future composite material systems. A simplified one dimensional analytical model is presented that is used to predict the strain at onset of transverse cracking. While it is accurate only for the most constrained cases, the model is important in that the predicted failure strain is seen to be a function of a lamina's thickness d and of the extensional stiffness bE theta of the adjacent laminae that constrain crack propagation in the 90 deg laminae.

Flaggs, D. L.↗