Search NASA⌕ Search

SEARCH · Search NASA

Results for “Strength of materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Enhanced negative thermal expansion of boron-doped Fe 43 Mn 28 Ga 28.97 B 0.03 alloy

Enhanced negative thermal expansion (NTE) properties are achieved by introducing a little amount of boron in the Fe 43 Mn 28 Ga 28.97 B 0.03 alloy. As a result, this alloy shows a giant NTE coefficient of alpha(1) = -79.7 x 10 -6 K -1 in a wide temperature range from 277 K to 136 K. Compared to the NTE characteristics in Fe 43 Mn 28 Ga 29 , the NTE operation temperature window has expanded by 74% with the corresponding coefficient of thermal expansion increased by 57% within the NTE temperature window for the boron-doped Fe 43 Mn 28 Ga28.97B0.03. Additionally, in-situ synchrotron high-energy X-ray diffraction results suggest that by boron substitution, the large unit cell volume change across martensitic transformation and the wide phase transition temperature interval are responsible for the pronounced NTE behavior in Fe 43 Mn 28 Ga 28.97 B 0.03 . Moreover, for the Fe 43 Mn 28 Ga 28.97 B 0.03 NTE material, the compressive strength and strain are significantly improved compared with that of Fe 43 Mn 28 Ga 29 . The present study indicates that Fe 43 Mn 28 Ga 28.97 B 0.03 with enhanced NTE across martensitic transformation may be used for practical application as thermal-expansion compensators.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quantum simulation of an exotic quantum critical point in a two-site charge Kondo circuit

Tuning a material to the cusp between two distinct ground states can produce physical properties that are unlike those in either of the neighbouring phases. Advances in the fabrication and control of quantum systems have raised the tantalizing prospect of artificial quantum simulators that can capture such behaviour. A tunable array of coupled qubits should have an appropriately rich phase diagram, but realizing such a system with either tunnel-coupled semiconductor quantum dots or metal nanostructures has proven difficult. The challenge for scaling up to clusters or lattices is to ensure that each element behaves essentially identically and that the coupling between elements is uniform, while also maintaining tunability of the interactions. Here we study a nanoelectronic circuit comprising two coupled hybrid metal–semiconductor islands, combining the strengths of both materials to form a potentially scalable platform. The semiconductor component allows for controllable inter-site couplings at quantum point contacts, while the metal component’s effective continuum of states means that different sites can be made equivalent by tuning local potentials. The couplings afforded by this architecture can realize an unusual quantum critical point resulting from frustrated Kondo interactions. In this study, the observed critical behaviour matches theoretical predictions, verifying the success of our experimental quantum simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Directed self-assembly of chiral liquid crystals into biomimetic bouligand structures in thin film

The Bouligand structure, renowned for its helicoidal arrangement and enhanced mechanical properties, has attracted significant research interest for its ability to impart enhanced strength to intrinsically soft materials. Biomimetic approaches have centered on fibrous structures in bulk materials, but translating this architecture into thin-film regime for miniaturized-wearable devices with programmable functions remains challenging. Here, we direct the self-assembly of cholesteric liquid crystals (CLCs) into hierarchical helical structures using chemically patterned surfaces. Alternating surface anchoring regions align uniform lying-down helices at the nanoscale, guiding a secondary microscale helical structure exhibiting both left- and right-handed twists. This mimetic Bouligand structure in CLCs enables optical modulation under applied field and strain with enhanced mechanical response. Simulations reveal the structural evolution from initial Bouligand configuration in LC layers to alternating twist helices. This research provides a basis for designing and manufacturing miniaturized or wearable devices with nanometer-scale precision in regulating electro-optical and mechanical properties. Bouligand structures, which offer strength in natural materials, are of interest but difficult to obtain. Here, the authors report the development of such structures by directed self-assembly of cholesteric single crystals into hierarchical helical structures, with the secondary structure having right and left-handed twists.

Bouligand structure↗
DOE OSTI2022

Investigation of fracture in porous materials: a phase-field fracture study informed by ReaxFF

Microscopic features (e.g, pore shapes, sizes, and distribution) in porous material substantially affect the overall mechanical properties such as stiffness and strength. In turn, these material properties determine the macroscopic behaviors of fracture in the porous material. In certain cases, macroscopic properties can be derived from the porous skeleton and void ratio (i.e., porosity), but in many other cases, such derivation is a challenging task. This paper presents a numerical investigation of microporosity and micropore shapes effect on the macrofracture behavior in porous amorphous silica. For this study, we extend the recently-proposed combined molecular dynamic (MD) and phase-field (PF) fracture modeling approach by including different pore shapes in the atomistic domain. In the MD simulations, we adopt ReaxFF to evaluate the material properties, where four different micropore cases are considered. Based on the material properties derived from MD simulations, the macrofracture propagation of porous media is studied using hybrid PF simulation. In the characterization of the pore structure, the concept of pore ligament is proposed to relate the pore shape and the critical energy release rate. Two classical fracture problems were used to evaluate the effect of pore shape on the macrofracture behavior. The results of the case study show that although the micropore shapes change the macrofracture behaviors, these effects vary with the geometry and loading conditions of macroscopic boundary value problems. Furthermore, the case study also shows that the influence of micropore structure can be captured at the macroscopic level through the material properties derived from the MD simulations.

42 ENGINEERING↗
DOE OSTI2020

Enhancement of Thermal Conductivity of Bentonite Buffer Materials with Copper Wires/Meshes for High-Level Radioactive Waste Disposal

In high-level radioactive waste disposal, a heat-generating waste canister is generally encased with a layer of bentonite-based buffer material acting as an engineered barrier to limit water percolation and radionuclide release. The low thermal conductivity of bentonite (~0.5 W/m∙K) combined with a high thermal loading waste package may result in a high surface temperature on the package that can potentially impact the structural integrity of the package itself as well as the surrounding buffer material. We show in this paper that the thermal conductivity of bentonite can be effectively enhanced by embedding copper wires/meshes across the buffer layer to form fully connected high heat conduction pathways. A simple calculation based on Rayleigh’s model shows that a required thermal conductivity of 5 W/m∙K for effective heat dissipation can be achieved simply by adding ~1 vol % of copper wires/meshes into bentonite. As a result, the peak surface temperature on a large waste package such as a dual-purpose canister can be reduced by up to 300°C, leading to a significant reduction in the surface storage time for waste cooling and therefore the overall cost for direct disposal of such waste packages. Because of the ensured full thermal percolation across the buffer layer, copper wires/meshes turn out to be much more effective than any other materials currently suggested (such as graphene or graphite) in enhancing the thermal conductivity of buffer material. Furthermore, the embedded copper wires/meshes can help reinforce the mechanical strength of the buffer material, thus preventing the material from a potential erosion by a possible intrusion of dilute groundwater.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fracturing process of micro-concrete under uniaxial and triaxial compression: Insights from in-situ X-ray mechanical tests

This paper presents an experimental study of concrete at meso-scale (aggregates, macro-pores and mortar matrix) in order to get a better understanding of the local failure mechanisms known to drive the macroscopic mechanical behaviour of the material. The main originality comes from conducting in-situ X-ray mechanical tests on micro-concrete samples of realistic composition (including cement, sand, aggregates and water), under uniaxial compression and, for the first time, under triaxial compression at 5 MPa, 10 MPa and 15 MPa confining pressures. A timeseries analysis of the set of 3D images coming from each test allows for the measurement of the 3D kinematic fields (displacement and strain fields) throughout the experiments. The different failure patterns observed for each loading path are discussed, along with a quantification of the 3D fracturing processes at the scale of the largest heterogeneities (aggregates and macro-pores). With an increasing level of confinement, the transition from brittle to ductile response is observed, as well as an increase of the strength of the material. The pronounced impact of the meso-scale heterogeneities of concrete on their local failure mechanisms is highlighted. It is shown that strain localisation mainly originates between aggregates and mortar matrix, with the shape and location of the largest aggregates and macro-pores essentially driving the propagation of the cracking network.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hydrogen-assisted fracture resistance of pipeline welds in gaseous hydrogen

Fracture resistance of pipeline welds from a range of strength grades and welding techniques was measured in air and 21 MPa hydrogen gas, including electric resistance weld of X52, friction stir weld of X100 and gas metal arc welds (GMAW) of X52, X65 and X100. Welds exhibited a decrease in fracture resistance in hydrogen compared to complementary tests in air. A general trend was observed that fracture resistance in 21 MPa hydrogen gas decreased with increasing yield strength. To accommodate material constraints, two different fracture coupon geometries were used in this study, which were shown to yield similar fracture resistance values in air and 21 MPa hydrogen gas; values using different coupons resulted in less than 15% difference. In addition, fracture coupons were removed from controlled locations in select welds to examine the potential influence of orientation and residual stress. The two orientations examined in the X100 GMAW exhibited negligible differences in fracture resistance in air and, similarly, negligible differences in hydrogen. Residual stress exhibited a modest influence on fracture resistance; however, a consistent trend was not observed between tests in air and hydrogen, suggesting further studies are necessary to better understand the influence of residual stress. A comparison of welds and base metals tested in hydrogen gas showed similar susceptibility to hydrogen-assisted fracture. The overall dominant factor in determining the susceptibility to fracture resistance in hydrogen is the yield strength.

08 HYDROGEN↗
DOE OSTI2020

A Review of Computational Models for the Flow of Milled Biomass Part I: Discrete-Particle Models

Biomass is a renewable and sustainable energy resource. Current design of biomass handling and feeding equipment leverage both experiments and numerical modeling. This paper reviews the state-of-the-art discrete element methods (DEM) for the flow of milled biomass (Part I), accompanied by a comprehensive review on continuum-based computational models (Part II). The present review on DEM is primarily focused on the features and suitability of various particle shape models for different types of milled biomass because particle shape is the predominant attribute controlling the flow behavior of complex-shaped granular material. The general strengths and weaknesses in the applicability of those models for the milled biomass modeling are summarized. In particular, comments are provided to balance the numerical model capabilities and the computational cost for the development of DEM models. To our best knowledge, this is the first-of-its-kind review on DEM specifically for biomass. Our study indicates that the current DEM models require further development, calibration, and validation based on a deep understanding of biomass particle contact mechanics and experimental data support before they can be reliably used for predictive simulations in handling and feeding systems.

42 ENGINEERING↗
DOE OSTI2022

[Presentation Slides] Code-to-Code Benchmark Study for Thermal Stress Modeling and Preliminary Analysis of the High-temperature Single Heat-Pipe Experiment

In the heat-pipe-cooled microreactor, heat pipes remove heat from the reactor core as a passive heat-transfer device, so the fluid circulation is not required for cooling, which can substantially simplify the overall reactor design. However, given the extremely high temperatures in the core region and potentially large temperature gradients across the structure materials, thermal stresses need to be well-analyzed to ensure structural integrity during normal operations and accident scenarios. This presentation slides discuss finite element method-based thermal-stress analysis for the high-temperature single heat-pipe test article in the Single Primary Heat Extraction and Removal Emulator (SPHERE) facility at Idaho National Laboratory (INL), using two commercial software packages, Abaqus and Star-CCM+. A code-to-code benchmark study was performed to crosscheck the model setup and capability of each code and to gain preliminary insights into the potential thermal stress concerns from the current experimental setup. It is observed the significant thermal stresses happen at the inner surface of the heat pipe hole surrounded by electric heaters where the largest temperature gradients appear. The temperature fields have good agreements between Abaqus and Star-CCM+, while the induced thermal stresses show modest deviations probably due to differences of meshing engines used in these two codes. It is found that the local maximum thermal stresses may reach close to the ultimate tensile strength and yield strength of structural material depending on the heater power. Ultimately, the coupled thermal-structural analysis will help guide the current experimental plan and ensure the facility safety for future experimental study.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Additive manufacturing of high‐density silicon carbide ceramics through post‐processing spark plasma sintering

This research advances the field of additive manufacturing (AM) of silicon carbide (SiC) ceramics by integrating spark plasma sintering (SPS) to enhance material density, mechanical strength, and thermal properties. Traditional AM techniques struggle to achieve the high‐density SiC required for demanding applications, such as aerospace engineering, where high thermal conductivity and mechanical strength are paramount. Here, our study addresses these challenges by incorporating SPS as a post‐processing step, achieving near‐theoretical maximum densities and significantly reducing porosity, thereby resulting in outstanding thermal conductivity in SiC ceramics. We developed a specialized SiC ink optimized for 3D printing, ensuring structural integrity after deposition through tailored rheological properties. The application of SPS facilitates rapid, uniform sintering, essential for attaining superior density, mechanical properties, and thermal performance. Our experimental results, confirmed through scanning electron microscopy analysis, demonstrate significant microstructural properties, mechanical strength, and thermal conductivity, showcasing the effectiveness of integrating SPS in AM processes. This innovative approach not only expands the capabilities of AM in producing complex, high‐density ceramic structures but also broadens the potential applications of SiC in demanding environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural development in DED stainless steels: applying welding models to elucidate the impact of processing and alloy composition

Austenitic stainless steel microstructures produced by directed energy deposition (DED)are analogous to those developed during welding, particularly high energy density welding. To better understand microstructural development during DED, theories of microstructural evolution,which have been established to contextualize weld microstructures, are applied in this study to microstructural development in DED austenitic stainless steels. Phenomenological welding models that describe the development of oxide inclusions, compositional microsegregation, ferrite,matrix austenite grains, and dislocation substructures are utilized to clarify microstructural evolution during deposition of austenitic stainless steels. Two different alloys, 304L and 316L, arecompared to demonstrate the broad applicability of this framework for understanding microstmctural development during the DED process. Despite differences in grain morphology and solidification mode for these two alloys (which can be attributed to compositional differences),similar tensile properties are achieved. It is the fine-scale compositional segregation and dislocation structures that ultimately determine the strength of these materials. The evolution of microsegregation and dislocation structures is shown to be dependent on the rapid solidification and thermomechanical history of the DED processing method and not the composition of the starting material.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-energy synchrotron x-ray study of deformation-induced martensitic transformation in a neutron-irradiated Type 316 stainless steel

An unusual tensile deformation behaviour in the form of a propagating band along the sample gauge was observed in two neutron-irradiated 316 stainless steel samples during room-temperature tests, leading to a combination of high strength and high ductility. These bands were not observed in an unirradiated counterpart. With the help of in situ high-energy synchrotron x-ray diffraction, the phase-specific crystal information was tracked at different deformation levels in each sample. Post-irradiation and post-deformation samples were examined using electron microscopy to characterize various microstructural features. All samples displayed a deformation-induced martensitic phase transformation, which was identified as a second strain-hardening mechanism accompanying the dislocation hardening. The deformation-induced martensitic transformation was rationalized by the effect of applied stress on the effective martensite start temperature. The results showed that the irradiation did not alter the dislocation hardening and the martensitic transformation mechanisms, but the increased yield strength in irradiated materials facilitated the localized phase transformation at the onset of plastic deformation, in contrast to the unirradiated material which required pre-straining. The hardening effect of the martensitic transformation reduced the tendency towards necking and mitigated the loss of ductility in the irradiated material by carrying the deformation in the form of a propagating band. Despite the beneficial effect from the martensitic transformation, this study indicates that this mechanism cannot not be activated at typical operating temperatures of nuclear reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Computational micromechanics model based failure criteria for chopped carbon fiber sheet molding compound composites

Chopped carbon fiber sheet molding compound has a great potential in lightweight automotive, marine, and aerospace applications. One of the most challenging tasks is to predict the failure strength of the material due to its anisotropy and heterogeneity, as well as complex stress states in real-world working conditions. In this work, a novel constitutive model of carbon fiber chip is proposed to capture the pre- and post-failure behaviors under different loading modes. On this basis, we propose a new computational micromechanics model, which is calibrated and validated by uniaxial tensile, compressive, and in-plane shear experiments. Furthermore, a set of microstructures representative volume element (RVE) models under complex loading conditions are reconstructed to understand the relationship between the microstructure characteristics and the failure envelopes. Finally, several modified versions of classical failure criteria are proposed for anisotropic materials with consideration of the fiber orientation tensor. The modified Tsai-Wu failure criterion, which shows the best accuracy among all failure criteria, is highlighted in the comparative study.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of ablators for the polar direct drive exploding pusher platform

In this work, we examine the performance of pure boron, boron carbide, high density carbon, and boron nitride ablators in the polar direct drive exploding pusher (PDXP) platform. The platform uses the polar direct drive configuration at the National Ignition Facility to drive high ion temperatures in a room temperature capsule and has potential applications for plasma physics studies and as a neutron source. The higher tensile strength of these materials compared to plastic enables a thinner ablator to support higher gas pressures, which could help optimize its performance for plasma physics experiments, while ablators containing boron enable the possibility of collecting additional data to constrain models of the platform. Applying recently developed and experimentally validated equation of state models for the boron materials, we examine the performance of these materials as ablators in 2D simulations, with particular focus on changes to the ablator and gas areal density, as well as the predicted symmetry of the inherently 2D implosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Fatigue behavior of fine-grained magnesium under tension-tension loading at 0 °C

Here, this study investigated low-temperature fatigue behavior of fine-grained magnesium through tension–tension fatigue testing at the temperature of 0 °C. The applied stress profiles of fatigue testing were selected to cover a wide range of loading conditions including low, medium, and high loading stresses. Even when the maximum applied stress of fatigue testing was as high as 88% of the ultimate tensile strength of the material, the corresponding fatigue life was long, i.e., 3973 cycles. Deformation accumulation per loading cycle reduced with the progression of fatigue testing for all studied loading conditions. Fatigue life analyses were performed using both Smith-Watson-Topper (SWT) model and Jahed-Varvani energy-based (JV) model. The fatigue life predictions through both models agree well with the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗
DOE OSTI2025

Optimizing Bendability and Hardness of Age-Hardenable Aluminum Sheets through Local Thermo-Mechanical Processing

This paper introduces a novel thermo-mechanical process to modify the local mechanical properties of 6xxx aluminum (Al-Mg-Si-Cu) alloy sheets. In this process, two pairs of rollers travel along the length of a sheet while locally bending and unbending it so that the final shape and thickness of the sheet remains unchanged. Room temperature bending/unbending (B/U) produces a deformation gradient through thickness and local hardening in both T4 and T6 sheets (with 41% and 18% greater Vickers hardness, respectively). High temperature bending/unbending performed at ~ 500°C via induction heating, produces significant improvements in local formability as measured by bend testing. Formability levels equivalent to the as-received T4 temper are achieved within the processed zones of T6 sheets with bend angles of ~ 150°, without disturbing the T6 temper in the remainder of the sheet. Finite element simulations and characterization explained the mechanical property improvements and the heterogenous microstructure with weakened Cube texture. Due to its similarity with the roller hemming process, and its compact dimensions, the apparatus developed for B/U has the potential for seamless integration with roller hemming robots to selectively process high strength aluminum sheet materials within mass-production settings.

Efe, Mert [BATTELLE (PACIFIC NW LAB)]↗