Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

A method for the dynamic and thermal stress analysis of space shuttle surface insulation

The thermal protection system of the space shuttle consists of thousands of separate insulation tiles bonded to the orbiter's surface through a soft strain-isolation layer. The individual tiles are relatively thick and possess nonuniform properties. Therefore, each is idealized by finite-element assemblages containing up to 2500 degrees of freedom. Since the tiles affixed to a given structural panel will, in general, interact with one another, application of the standard direct-stiffness method would require equation systems involving excessive numbers of unknowns. This paper presents a method which overcomes this problem through an efficient iterative procedure which requires treatment of only a single tile at any given time. Results of associated static, dynamic, and thermal stress analyses and sufficient conditions for convergence of the iterative solution method are given.

Ojalvo, I. U.↗
NASA NTRS1976

Nonlinear effects in thermal stress analysis of a solid propellant rocket motor

Direct characterization procedures were used to determine the relaxation modulus as a function of time, temperature, and state of strain. Using the quasi-elastic method of linearviscoelasticity, these properties were employed in a finite element computer code to analyze a thick-walled, nonlinear viscoelastic cylinder in the state of plane strain bonded to a thin (but stiff) elastic casing and subjected to slow thermal cooling. The viscoelastic solution is then expressed as a sequence of elastic finite element solutions. The strain-dependent character of the relaxation modulus is included by replacing the single relaxation curve used in the linear viscoelastic theory by a family of relaxation functions obtained at various strain levels. These functions may be regarded as a collection of stress histories or responses to specific loads (in this case, step strains) with which the cooldown solution is made to agree by iterations on the modulus and strain level.

Francis, E. C.↗
NASA NTRS2008

Ares I-X Upper Stage Simulator Residual Stress Analysis

The structural analyses described in the present report were performed in support of the NASA Engineering and Safety Center (NESC) Critical Initial Flaw Size (CIFS) assessment for the Ares I-X Upper Stage Simulator (USS) common shell segment. An independent assessment was conducted to determine the critical initial flaw size (CIFS) for the flange-to-skin weld in the Ares I-X Upper Stage Simulator (USS). The Ares system of space launch vehicles is the US National Aeronautics and Space Administration s plan for replacement of the aging space shuttle. The new Ares space launch system is somewhat of a combination of the space shuttle system and the Saturn launch vehicles used prior to the shuttle. Here, a series of weld analyses are performed to determine the residual stresses in a critical region of the USS. Weld residual stresses both increase constraint and mean stress thereby having an important effect on fatigue and fracture life. The results of this effort served as one of the critical load inputs required to perform a CIFS assessment of the same segment.

Raju, Ivatury S.↗
DOE OSTI2024

Electromagnetic Design Optimization Integrated with Mechanical Stress Analysis of PM-Assisted Synchronous Reluctance Machine Topologies Enabled with a Blend of Magnets

Permanent Magnet-Assisted Synchronous Reluctance Machines (PMASynRM) provide a low-cost alternative to Surface PM Machines due to the use of relatively lower grades of rare-earth (RE) or RE-free magnets, as the performance degradation due to weaker magnets is compensated by the presence of reluctance torque. However, the weaker magnets suffer from a high risk of demagnetization, leading to unreliable motor operation. Using a blend of RE and RE-free magnets has the potential to overcome this issue. This paper proposes to blend different grades of various rare-earth (RE) and rare-earth-free (RE-free) magnets in six different combinations and utilizes them in two-layer and three-layer U-shaped PMASynRM topologies with both eight-pole and six-pole variations. The rotor of the various designs is then optimized using a differential evolution (DE) based optimization algorithm to obtain low-cost designs with reduced RE magnet volume and minimum demagnetization risk. The optimization of each design is also integrated with the evaluation of mechanical stresses in the rotor laminations so as to maintain the stresses below the material yield strength. Furthermore, the various performance metrics, such as toque–speed/power–speed characteristics, demagnetization, and efficiency maps, are evaluated for each of the optimized and mechanically feasible designs. A quantitative comparison of the various optimized designs is also obtained to highlight the various trade-offs. The results indicate the feasibility of meeting the baseline torque requirement across the entire speed range, even with a 100% reduction in RE magnet volume and less than 5% demagnetization risk, while achieving a cost reduction exceeding 50%. Moreover, the two-layer, eight-pole designs exhibit relatively higher performance, whereas the three-layer, eight-pole designs are found to be the most economical option.

design optimization↗
NASA NTRS1953

Deflection and Stress Analysis of Thin Solid Wings of Arbitrary Plan Form with Particular Reference to Delta Wings

The structural analysis of arbitrary solid cantilever wings by small-deflection thin-plate theory is reduced to the solution of linear ordinary differential equations by the assumption that the chordwise deflections at any spanwise station may be expressed in the form of a power series in which the coefficients are functions of the spanwise coordinate. If the series is limited to the first two and three terms (that is, if linear and parabolic chordwise deflections, respectively, are assumed), the differential equations for the coefficients are solved exactly for uniformly loaded solid delta wings of constant thickness ratio. For cases for which exact solutions to the differential equations cannot be obtained, a numerical procedure is derived. Experimental deflection and stress data for constant-thickness delta-plate specimens of 45 degree and 60 degree sweep are presented and are found to compare favorably with the present theory.

Stein, Manuel↗
NASA NTRS1967

Computer program performs rectangular fitting stress analysis

Computer program simulates specific bulkhead fittings by subjecting the desired geometry configuration to a membrane force, an external force, an external moment, an external tank pressure, or any combination of the above. This program generates a general model of bulkhead fittings for the Saturn booster.

Bertrand, A. R.↗
NASA NTRS1972

High pressure turbine blade stress analysis

Combinations of high temperature gradients associated with strong transients in both temperature and rotational speed fields are discussed. Blade definition and results of the analysis are shown. Since the same model should later be used to define some dynamic characteristics and certain areas would require a nonlinear analysis, NASTRAN was chosen as a convenient program to manage the several alternatives.

Vannimwegen, R. R.↗
NASA NTRS1978

A simple element for multilayer beams in NASTRAN thermal stress analysis

In the application of NASTRAN, structural members are usually represented by bar elements with multipoint constraint cards to enforce the interface conditions. While this is a very powerful method in principle, it was found that in practice the process for specification of constraints became tedious and error prone, unless the geometry was simple and the number of grid points low. An alternative approach was found within the framework of the NASTRAN program. This approach made use of the idea that a thermal distortion in a multilayer beam may be similar to a homogeneous beam with a thermal gradient across the cross section. The exact mathematical derivation for the equivalent beam, and all the necessary formulae for the equivalent parameters in NASTRAN analysis are presented. Some numerical examples illustrate the simplicity and ease of this approach for finite element analysis.

Chen, W. T.↗
NASA NTRS1979

Application of numerical methods to heat transfer and thermal stress analysis of aerospace vehicles

The paper describes a thermal-structural design analysis study of a fuel-injection strut for a hydrogen-cooled scramjet engine for a supersonic transport, utilizing finite-element methodology. Applications of finite-element and finite-difference codes to the thermal-structural design-analysis of space transports and structures are discussed. The interaction between the thermal and structural analyses has led to development of finite-element thermal methodology to improve the integration between these two disciplines. The integrated thermal-structural analysis capability developed within the framework of a computer code is outlined.

Wieting, A. R.↗
NASA NTRS1982

Experimental stress analysis of a thin-walled pressurized torus loaded by contact with a plane

It is pointed out that pneumatic tires have a large effect on the overall landing characteristics of an aircraft. The dynamic response upon landing and steering are crucial to the safety of the vehicle and the occupants. The present investigation has the objective to compare experimentally determined strains on an inner tube in contact with a flat plate with numerical values obtained on the basis of a finite element prediction, taking into account an employment of the Structural Analysis of General Shells (STAGS). The obtained results suggest that the clamped boundary condition utilized in the STAGS calculation is not exactly simulated by the employed test setup.

Hill, D. E.↗