Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface elasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Tailoring Elastic Properties of Silica Aerogels Cross-Linked with Polystyrene

The effect of incorporating an organic linking group, 1,6-bis(trimethoxysilyl)hexane (BTMSH), into the underlying silica structure of a styrene cross-linked silica aerogel is examined. Vinyltrimethoxysilane (VTMS) is used to provide a reactive site on the silica backbone for styrene polymerization. Replacement of up to 88 mol 1 of the silicon from tetramethoxyorthosilicate with silicon derived from BTMSH and VTMS during the making of silica gels improves the elastic behavior in some formulations of the crosslinked aerogels, as evidenced by measurement of the recovered length after compression of samples to 251 strain. This is especially true for some higher density formulations, which recover nearly 100% of their length after compression to 251 strain twice. The compressive modulus of the more elastic monoliths ranged from 0.2 to 3 MPa. Although some of these monoliths had greatly reduced surface areas, changing the solvent used to produce the gels from methanol to ethanol increased the surface area in one instance from 6 to 220 sq m2/g with little affect on the modulus, elastic recovery, porosity, or density.

Nguyen, Baochau N.↗
NASA NTRS1997

A Feasibility Study to Control Airfoil Shape Using THUNDER

The objective of this study was to assess the capabilities of a new out-of-plane displacement piezoelectric actuator called thin-layer composite-unimorph ferroelectric driver and sensor (THUNDER) to alter the upper surface geometry of a subscale airfoil to enhance performance under aerodynamic loading. Sixty test conditions, consisting of combinations of five angles of attack, four dc applied voltages, and three tunnel velocities, were studied in a tabletop wind tunnel. Results indicated that larger magnitudes of applied voltage produced larger wafer displacements. Wind-off displacements were also consistently larger than wind-on. Higher velocities produced larger displacements than lower velocities because of increased upper surface suction. Increased suction also resulted in larger displacements at higher angles of attack. Creep and hysteresis of the wafer, which were identified at each test condition, contributed to larger negative displacements for all negative applied voltages and larger positive displacements for the smaller positive applied voltage (+102 V). An elastic membrane used to hold the wafer to the upper surface hindered displacements at the larger positive applied voltage (+170 V). Both creep and hysteresis appeared bounded based on the analysis of several displacement cycles. These results show that THUNDER can be used to alter the camber of a small airfoil under aerodynamic loads.

Pinkerton, Jennifer L.↗
NASA NTRS1991

On the strain energy of laminated composite plates

The present effort to obtain the asymptotically correct form of the strain energy in inhomogeneous laminated composite plates proceeds from the geometrically nonlinear elastic theory-based three-dimensional strain energy by decomposing the nonlinear three-dimensional problem into a linear, through-the-thickness analysis and a nonlinear, two-dimensional analysis analyzing plate formation. Attention is given to the case in which each lamina exhibits material symmetry about its middle surface, deriving closed-form analytical expressions for the plate elastic constants and the displacement and strain distributions through the plate's thickness. Despite the simplicity of the plate strain energy's form, there are no restrictions on the magnitudes of displacement and rotation measures.

Atilgan, Ali R.↗
NASA NTRS1992

Variations in lithospheric thickness on Venus

Recent analyses of Magellan data have indicated many regions exhibiting topograhic flexure. On Venus, flexure is associated predominantly with coronae and the chasmata with Aphrodite Terra. Modeling of these flexural signatures allows the elastic and mechanical thickness of the lithosphere to be estimated. In areas where the lithosphere is flexed beyond its elastic limit the saturation moment provides information on the strength of the lithosphere. Modeling of 12 flexural features on Venus has indicated lithospheric thicknesses comparable with terrestrial values. This has important implications for the venusian heat budget. Flexure of a thin elastic plate due simultaneously to a line load on a continuous plate and a bending moment applied to the end of a broken plate is considered. The mean radius and regional topographic gradient are also included in the model. Features with a large radius of curvature were selected so that a two-dimensional approximation could be used. Comparisons with an axisymmetric model were made for some features to check the validity of the two-dimensional assumption. The best-fit elastic thickness was found for each profile crossing a given flexural feature. In addition, the surface stress and bending moment at the first zero crossing of each profile were also calculated. Flexural amplitudes and elastic thicknesses obtained for 12 features vary significantly. Three examples of the model fitting procedures are discussed.

Johnson, C. L.↗
NASA NTRS1986

An imaging extreme ultraviolet spectrometer for astrophysical investigations in space

A high-efficiency, extreme ultraviolet (EUV) imaging spectrometer has been constructed and tested. The spectrometer employs a concave toroidal grating illuminated at normal incidence in a Rowland circle mounting and has only one reflecting surface. The toroidal grating has been fabricated by a new technique employing an elastically deformable submaster grating which is replicated in a spherical form and then mechanically distorted to produce the desired aspect ratio of the toroidal surface for stigmatic imaging over the selected wavelength range. The fixed toroidal grating used in the spectrometer is then replicated from this surface. Photographic tests and initial photoelectric tests with a two-dimensional, pulse-counting detector system have verified the image quality of the toroidal grating at wavelengths near 600 A. The basic designs of two instruments employing the spectrometer for astrophysical investigations in space are described, namely, a high-resolution EUV spectroheliometer for studies of the solar chromosphere, transition region, and corona; and an EUV spectroscopic telescope for studies of nonsolar objects.

Huber, M. C. E.↗
NASA NTRS1993

Effective elastic thickness of the Venusian lithosphere with lateral viscosity variations in the mantle

Both the Earth and Venus have a convecting mantle at the top of which is a relatively strong, mechanical boundary layer. The surface topography and gravity signals which result from the convection within the viscous mantle are modified by the elastic properties of this lithospheric boundary layer. In particular the ability of the lithosphere to support loads and transmit stresses from below is a function of the wavelength of the load--the lithosphere is strong to loading at shorter wavelengths. As a consequence it is usual to expect that long wavelength topography cannot be supported by the mechanical strength of the lithosphere and must be compensated--isostatically or dynamically--within the uppermost mantle or the crust. The flexural rigidity of the lithosphere can therefore be determined by estimating the greatest wavelength at which uncompensated surface topography can be supported, usually by measuring the admittance as a function of wavelength. In fact this procedure for determining the elastic thickness relies upon being able to distinguish topography with underlying support from that supported by the brittle lithosphere on the basis of their each having a characteristic value of the admittance. However, in the presence of lateral viscosity variations in the mantle, it is possible for topography to be generated which is NOT compensated by density anomalies in the underlying mantle at the same wavelength. Although this effect is not likely to be important for the Earth, on Venus, where the high surface temperatures would be expected to give a weaker lithosphere, lateral viscosity variations in the mantle can give a misleadingly large apparent elastic thickness for the lithosphere.

Moresi, Louis↗
NASA NTRS1993

Ridge belt-related scarps and troughs: Compressional crustal bending on Venus

Cytherean ridge arcs resulted in crustal shortening in places with either the strongest compression or weakest surface layers. Arcuate scarps on or close to the edge of the ridge arcs were compressional fronts formed by overthrust over or subduction of adjacent lowland. These ridge arcs became wider due to the propagation of new ridge formation close to previous one(s). As this process repeated itself with time, the crust became thicker and the foreland was bent either due to the excess load, overthrust or subduction event. The Salme Dorsa arc measures 100 km in width and 600 km in length. It consists of a horseshoe-like set of ridges and grooves on a gently sloping lowland. The westward arcuate ridge belt indicates lateral compressional stresses and crustal deformation from SE against the southern Ishtar Terra foreland plain. The trough on the western side of the ridge belt and tensional grabens close to the crest of the bulge to the west of the trough are due to the crustal bending and indicate effects of the load and thrust. Compression and relative movement from southeast against and over the foreland planitia have resulted in ridge belt, trough and bulge formation. The load- and/or stress-induced bending of the uppermost crust allows some estimations of the uppermost elastic lithosphere thickness. Repeated folding and thrust faulting of surface layers due to compression are indicated by four more ridge belts located close to Salme Dorsa. The northeasternmost one has short ridges located in troughs. The west-opening arcuate ridge belt interlocks with the Salme Dorsa horseshoe.

Raitala, J.↗
NASA NTRS1973

Fracture analysis of surface- and through-cracked sheets and plates.

The Neuber stress-concentration relation for notches in an elastic-plastic material subjected to shear loading was generalized for a crack in a finite plate subjected to tensile loading. An equation was derived which related the linear elastic stress-intensity factor, the applied stress, and two material parameters. The equation was then used as a two-parameter fracture criterion for surface- and through-cracked specimens. Fracture data from the literature on surface- and through-cracked sheet and plate specimens of steel, titanium alloy, titanium weldment, and aluminum alloy tested at room and cryogenic temperature were analyzed according to the proposed equation. For surface cracks, wide ranges of crack-depth to crack-length ratio and crack-depth to specimen-thickness ratio were considered. For through cracks, wide ranges of crack length and specimen width were also considered.-

Newman, J. C., Jr.↗
NASA NTRS1987

The evaluation of a deformable diffraction grating for a stigmatic EUV spectroheliometer

A high-efficiency, extreme ultraviolet (EUV) imaging spectrometer is constructed and tested. The spectrometer employs a concave toroidal grating illuminated at normal incidence in a Rowland circle mounting and has only one reflecting surface. The toroidal grating has been fabricated by a new technique employing an elastically-deformable sub-master grating replicated in a spherical form and then mechanically distorted to produce the desired aspect ratio of the toroidal surface for stigmatic imaging over the selected wavelength range. The fixed toroidal grating used in the spectrometer is then replicated from this surface. Photographic tests and initial photoelectric tests with a two-dimensional, pulse-counting detector system verify the image quality of the toroidal grating at wavelengths near 600 A. The results of these tests and the basic designs of two instruments which could employ the imaging spectrometer for astrophysical investigations in space are described; i.e., a high-resolution EUV spectroheliometer for studies of the solar chromosphere, transition region, and corona; and an EUV spectroscopic telescope for studies of non-solar objects.

Timothy, J. G.↗
NASA NTRS1971

Work function measurements by the field emission retarding potential method

Using the field emission retarding potential method true work functions have been measured for the following monocrystalline substrates: W(110), W(111), W(100), Nb(100), Ni(100), Cu(100), Ir(110) and Ir(111). The electron elastic and inelastic reflection coefficients from several of these surfaces have also been examined near zero primary beam energy.

Swanson, L. W.↗
NASA NTRS1973

Fatigue of boron-aluminum composites bonds and joints

Study examines effects of boron filament diameter on bonds and joints in boron-aluminum composite. Data include static strength, fatigue, and dynamic moduli of elasticity. Manson-Coffin analyses and metallurgical and fracture surface evaluation were also performed.

Hersh, M. S.↗
NASA NTRS1982

Abstracts of papers presented at the Eleventh International Laser Radar Conference

Abstracts of 39 papers discuss measurements of properties from the Earth's ocean surface to the mesosphere, made with techniques ranging from elastic and inelastic scattering to Doppler shifts and differential absorption. Topics covered include: (1) middle atmospheric measurements; (2) meteorological parameters: temperature, density, humidity; (3) trace gases by Raman and DIAL techniques; (4) techniques and technology; (5) plume dispersion; (6) boundary layer dynamics; (7) wind measurements; visibility and aerosol properties; and (9) multiple scattering, clouds, and hydrometers.

Source record↗
NASA NTRS1986

Numerical quadrature methods for integrals of singular periodic functions and their application to singular and weakly singular integral equations

High accuracy numerical quadrature methods for integrals of singular periodic functions are proposed. These methods are based on the appropriate Euler-Maclaurin expansions of trapezoidal rule approximations and their extrapolations. They are used to obtain accurate quadrature methods for the solution of singular and weakly singular Fredholm integral equations. Such periodic equations are used in the solution of planar elliptic boundary value problems, elasticity, potential theory, conformal mapping, boundary element methods, free surface flows, etc. The use of the quadrature methods is demonstrated with numerical examples.

Sidi, A.↗
NASA NTRS1986

Manned Mars mission surface transportation elements

The necessity and advantage of surface transportation was well demonstrated by the Apollo 15, 16, and 17 missions. Baseline surface transportation elements for further studies are Lunar Rover, Elastic Loop Mobility System, Mobile Laboratory, Airplane, and Rocket Powered Flying Vehicles.

S Gregg McDaniel↗
NASA NTRS1992

Stress and tectonics on Mars

Deformation of the Martian lithosphere and the various theoretical formulations used to model its behavior on local, regional, and global scales are studied. An overview of the various classes of tectonic features found on Mars is presented. The tectonic record on Mars, which provides the basic framework for interpreting theoretical thermomechanical models in terms of major tectonic events and provinces is summarized. The thickness of the elastic lithosphere is estimated using its response to local surface loads, and significant spatial variability is found, with values ranging from 20 to 300 km. A comparison of the major radial graben systems with theoretical stress models shows that more than one mechanism of lithospheric deformation is required to produce its enormous extent.

Banerdt, W. B.↗
NASA NTRS1997

Thermal Fatigue Testing of ZrO2-Y2O3 Thermal Barrier Coating Systems using a High Power CO2 Laser

In the present study, the mechanisms of fatigue crack initiation and propagation, and of coating failure, under thermal loads that simulate diesel engine conditions, are investigated. The surface cracks initiate early and grow continuously under thermal Low Cycle Fatigue (LCF) and High Cycle Fatigue (HCF) stresses. It is found that, in the absence of interfacial oxidation, the failure associated with LCF is closely related to coating sintering and creep at high temperatures. Significant LCF and HCF interactions have been observed in the thermal fatigue tests. The fatigue crack growth rate in the ceramic coating strongly depends on the characteristic HCF cycle number, N*(sub NCF), which is defined as the number of HCF cycles per LCF cycle. The crack growth rate is increased from 0.36 microns/LCF cycle for a pure LCF test to 2.8 microns/LCF cycle for a combined LCF and HCF test at N*(sub NCF) about 20,000. A surface wedging model has been proposed to account for the HCF crack growth in the coating systems. This mechanism predicts that HCF damage effect increases with increasing surface temperature swing, the thermal expansion coefficient and the elastic modulus of the ceramic coating, as well as with the HCF interacting depth. A good agreement has been found between the analysis and experimental evidence.

Zhu, Dongming↗
NASA NTRS2003

Modeling and Control of Aerothermoelastic Effects

Aerothermoelasticity comprises those aspects of the dynamics of an aircraft that are caused by flexibility and heating during flight. The concept of aerothermoelasticity is particularly important for hypersonic vehicles that operate at extremely high dynamic pressures. The design requirements for such vehicles often introduce long and thin fuselages subject to elastic bending in low-frequency vibrational modes. Furthermore, surface heating can significantly change the stiffness characteristics of these modes. These aerothermoelastic effects must be considered in the synthesis and analysis of control systems. The present method makes it possible to incorporate the results of computational analysis into the small linear models that are typically used in designing controls.

Lind, Rick↗