Search NASA⌕ Search

SEARCH · Search NASA

Results for “Suspension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Composite coatings from polycarbosilane derived SiC and Al/SiC cermet active fillers as protective barriers against steel corrosion

Stainless steel is used throughout the world as a structural material. However, it undergoes corrosion damage when exposed to extremely corrosive media, such as the marine environment. An alternative to solve this problem lies in the development of coatings that can withstand extreme conditions but also be easily deposited with inherently corrosion-resistant materials such as silicon carbide (SiC). The present study shows a simple method to produce Al/SiC cermet powders by attrition milling. The resulting cermet powders with a metallic matrix and hemispherical morphology, were employed as fillers in polycarbosilane (PCS) solutions that were sprayed on A304 stainless steel substrates. Al/SiC composite coatings were produced after heating the sprayed suspensions at 700 °C for 1 h in Ar atmosphere. The resulting composite coatings exhibited low surface energies (< 35 mN/m), water contact angles of 53°, and adhesion strength of up to 30 MPa. Finally, corrosion tests were performed in a cyclic corrosion test chamber, showing that these coatings effectively reduced the corrosion rate of stainless steel by 87%, reaching corrosion rate values of 0.007 g/cm 2 year.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Performance of a Drifting Acoustic Instrumentation SYstem (DAISY) for characterizing radiated noise from marine energy converters

Marine energy converters can generate electricity from energetic ocean waves and water currents. Because sound is extensively used by marine animals, the radiated noise from these systems is of regulatory interest. However, the energetic nature of these locations poses challenges for performing accurate passive acoustic measurements, particularly with stationary platforms. The Drifting Acoustic Instrumentation SYstem (DAISY) is a modular hydrophone recording system purpose-built for marine energy environments. Using a flow shield in currents and mass–spring–damper suspension system in waves, we demonstrate that DAISYs can effectively minimize the masking effect of flow noise at frequencies down to 10 Hz. In addition, we show that groups of DAISYs can utilize time-delay-of-arrival post-processing to attribute radiated noise to a specific source. Consequently, DAISYs can rapidly measure radiated noise at all frequencies of interest for prototype marine energy converters. Furthermore, the resulting information from future operational deployments should support regulatory decision-making and allow technology developers to make design adjustments that minimize the potential for acoustic impacts as their systems are scaled up for utility-scale power generation.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Non-linear Wire Rope Isolator Model to Enhance Transportation Simulation of Fragile Equipment

Abstract Introduction Wire rope isolators are often used as means of vibration isolation for the transportation of fragile machine equipment. When deployed as suspension systems in a transportation scenario, a simple spring–damper model is often used to predict the dynamic loads that act on the structure being transported. However, this simple model has proved to be too simplistic to be used in the development of an accurate numerical model that can predict the vibration levels experienced by the inner components of fragile equipment during its transportation. This paper describes the experimental tests conducted on a wire rope isolator used for the transportation of the prototype SSR1 cryomodule. Materials and methods A hysteretic Bouc–Wen model has been used to analytically describe the force–deformation relationship of the wire rope isolators. The developed model of the isolator has been implemented in a larger model to simulate the actual transportation of the prototype SSR1 cryomodule, a section of the new PIP-II linear accelerator under construction at Fermilab. A series of multibody dynamic simulations with rigid and flexible components was used to numerically determine the acceleration of some critical components. Results and conclusions An actual experimental transportation was simulated using two numerical models: the developed Bouc–Wen model and a conventional spring–damper model. It is shown how the Bouc–Wen formulation of the isolator characteristics drastically improves the correspondence between experimental and simulated results if compared to a spring–damper model, especially in the range of 0–30 Hz which is the most critical for transportation problems.

42 ENGINEERING↗
DOE OSTI2025

Embedded 3D printing of isotropically enhanced lattice structure with programmable elasticity via three-dimensional fiber alignment

Engineered composites with fiber orientation in a complete three-dimensional (3D) context are highly desired for maximizing structural performance as they mimic the well-organized fiber arrangement in natural composites. However, most fabrication techniques lack the capability for through-plane (z-axis) alignment, limiting the possibility for structural design and performance optimization. In this study, we present an embedded 3D printing approach that enables complete 3D fiber alignment, including region-specific alignment control along the through-plane direction. Our method utilizes the extrusion and suspension of composite inks within a supporting matrix. By regionally adjusting the ink extrusion rate and nozzle translation rate, we locally manipulated the fiber arrangement within the composite 3D architecture. Here, we demonstrate that the 3D alignment of carbon fibers in a structural composite significantly enhances both mechanical properties and thermal conductivity in the in-plane and through-plane directions. Furthermore, by strategically arranging regional fiber orientations within micro-architected materials, we fabricated metamaterial engineered composites with programmable anisotropy ratio and directional moduli.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pragmatic protocols for working cleanly when measuring ice nucleating particles

We report that measuring ice nucleating particles (INPs) is critical for understanding, and modeling, cloud formation, reflectivity, and precipitation patterns. However, because INPs are very rare in the atmosphere, but abundant—sometimes alarmingly so—in the dust that covers all work surfaces, contamination during processing of collected aerosol samples can be a significant hindrance to obtaining accurate measures of INPs. In preparing this technical note, we questioned the cleanliness of every collection and processing step involved in making immersion freezing measurements of INPs re-suspended from filter samples. The aim was to identify, and then minimize, all potential sources of significant contamination, including containers and tools used to store filters and prepare liquid suspensions, gloves, work surfaces, and the polymerase chain reaction (PCR) trays commonly used for sample analysis. While plasticware released few INPs, most gloves readily shed them, but this can be mitigated by using washed cleanroom vinyl or polyethylene gloves. Work surfaces, even those that had been cleaned, were prodigious reservoirs of contaminating INPs, but simply covering them with aluminum foil will provide an INP-free surface. By applying these practices, we developed a method to reduce the background level of INPs on Nuclepore™ polycarbonate filters in our tests to 0 at -25 °C and < 20 at -27 °C, making them suitable for use in all sampling environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Inferring colloidal interaction from scattering by machine learning

A machine learning solution for the potential inversion problem in elastic scattering is outlined. The inversion scheme consists of two major components, a generative network featuring a variational autoencoder which extracts the targeted static two-point correlation functions from experimentally measured scattering cross sections, and a Gaussian process framework which probabilistically infers the relevant structural parameters from the inverted correlation functions. Via a case study of charged colloidal suspensions, the feasibility of this approach for quantitative study of molecular interaction is critically benchmarked and its merit over existing deterministic approaches, in terms of numerical accuracy and computationally efficiency, is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Studies of selenium and arsenic mutual protection in human HepG2 cells

Hundreds of millions of people worldwide are exposed to unacceptable levels of carcinogenic inorganic arsenic. Animal models have shown that selenium and arsenic are mutually protective through the formation and elimination of the seleno-bis(S-glutathionyl) arsinium ion [(GS) 2 AsSe] - . Consistent with this, human selenium deficiency in arsenic-endemic regions is associated with arsenic-induced disease, leading to the initiation of human selenium supplementation trials. In contrast to the protective effect observed in vivo, in vitro studies have suggested that selenite increases arsenite cellular retention and toxicity. This difference might be explained by the rapid conversion of selenite to selenide in vivo. In the current study, selenite did not protect the human hepatoma (HepG2) cell line against the toxicity of arsenite at equimolar concentrations, however selenide increased the IC 50 by 2.3-fold. Cytotoxicity assays of arsenite + selenite and arsenite + selenide at different molar ratios revealed higher overall mutual antagonism of arsenite + selenide toxicity than arsenite + selenite. Despite this protective effect, in comparison to 75 Se-selenite, HepG2 cells in suspension were at least 3-fold more efficient at accumulating selenium from reduced 75 Se-selenide, and its accumulation was further increased by arsenite. X-ray fluorescence imaging of HepG2 cells also showed that arsenic accumulation, in the presence of selenide, was higher than in the presence of selenite. These results are consistent with a greater intracellular availability of selenide relative to selenite for protection against arsenite, and the formation and retention of a less toxic product, possibly [(GS) 2 AsSe] - .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Resting time effect on the rheological behavior of cement paste in presence of superplasticizer

Rheology has been widely used to describe the flow properties of fresh cement-based suspensions. Nevertheless, the effect of early hydration product formation on rheology, and the effect of shear on breaking of hydration bonds is not fully understood. Therefore, the characterization of the time-dependency of rheology has become necessary to predict precisely the behavior of concrete during placement. In this paper, variations in the resting time in between rheological tests were imposed to evaluate the effects on the development of internal structure of the mixture using different dispersing agents. Increasing resting time in between measurements mainly enhances viscosity, but the magnitude seems strongly dependent on the dispersant used. However, the effect of the employed procedure, as two procedures were evaluated, seems to have a stronger influence on the time-evolution of the rheological properties than changing the resting time in between measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A new approach to study adsorption on shales and other microporous solids via the thermogravimetric analysis (TGA) technique

Measuring the adsorption of gases in microporous solids like the shales requires accurate knowledge of the solid’s skeletal volume. Helium (He) is commonly used to determine the sample’s skeletal volume based on the assumption that it does not adsorb in these porous media. The validity of such an assumption for microporous solids has been questioned in recent years, and in this study, we show that it is not applicable for the shale sample studied. We present a new method to measure the adsorption of shale-gas components in shales, which does not require the use of He to measure the solid’s skeletal volume. Since the proposed analysis method relies on the use of dynamic adsorption data, we also propose here a new zero-point correction method for the magnetic suspension balance, which is better suited for the analysis of such data. Here, we employ the new technique to the study of Argon adsorption in Marcellus Shales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Iron precipitation under controlled oxygen flow: Mineralogical implications for BIF precursors in the Archean ocean

Banded iron formation (BIF) deposition in the Archean ocean is thought to have been initiated by the oxidation of dissolved iron into ferric primary precursor phases that descended through the water column and were deposited on the seafloor. Effective interpretation of the trace element and isotopic composition of BIFs in the geologic record requires an understanding of the identity and longevity of those precursor phases. Temporal and spatial variation in oxidant concentration and ocean chemistry may have driven precursor mineralogy. Furthermore, precursor phases may undergo transitions during descent and burial. This experimental study follows the evolution of iron mineralogy, speciation, and redox state during the precipitation of iron under variable oxygen fluxes and in fluids containing different iron-complexing anions (chloride, sulfate, and phosphate). Additionally, suspensions collected after incomplete oxidation were anoxically aged to simulate changes to precursor mineralogy during descent below the seawater redoxcline. Results from X-ray diffraction, sequential dissolution, colorimetric determination of Fe redox state, and Fe K-edge X-ray absorption fine structure spectroscopy showed that under all experimental conditions, intermediate precipitates collected before complete iron uptake contained mineralized ferrous iron. Purely ferric mineral assemblages were not observed until iron was removed from solution. In low-oxygen experiments, intermediate precipitates contained phases with stoichiometric Fe 2+ , including magnetite, vivianite, and green rust (GR). Chloride green rust (GR1) had more ferric iron than sulfate green rust (GR2) and more readily transitioned to magnetite via disproportionation. GR2 was stable over a broader range of iron uptake; magnetite appeared mainly as an additional oxidation product in sulfate solution. In high oxygen experiments, mineralized ferrous iron occurred in amorphous phases or as a non-stoichiometric component in ferric oxides; final ferric assemblages were less crystalline than in low-oxygen equivalents. Low concentrations of phosphate increased the total iron oxidation rate, but also increased the ferrous content of intermediate precipitates. The incorporation of phosphate stabilized GR2 and facilitated GR2 precipitation over a larger range of iron uptake. In higher concentrations of phosphate, vivianite and poorly crystalline ferric hydroxides formed in place of GR. Here, these findings suggest that over a range of possible ocean chemistries, mixed-valence phases may have been short lived but relevant precursors to BIF. Additionally, anionic chemistry and oxidant concentration are shown to influence the crystallinity and chemical resistivity of final ferric assemblages, affecting their reactivity during later anoxic burial.

58 GEOSCIENCES↗
DOE OSTI2021

Influence of QD photosensitizers in the photocatalytic production of hydrogen with biomimetic [FeFe]-hydrogenase. Comparative performance of CdSe and CdTe

Photocatalytic systems comprising a hydrogenase-type catalyst and CdX (X = S, Se, Te) chalcogenide quantum dot (QD) photosensitizers show extraordinary hydrogen production rates under visible light excitation. What remains unknown is the mechanism of energy conversion in these systems. In this work, we have explored this question by comparing the performance of two QD sensitizers, CdSe and CdTe, in photocatalytic systems featuring aqueous suspensions of a [Fe 2 (μ-1,2-benzenedithiolate) CO 6 ] catalyst and an ascorbic acid sacrificial agent. Overall, the hydrogen production yield for CdSe-sensitized reactions QDs was found to be 13 times greater than that of CdTe counterparts. According to emission quenching experiments, an enhanced performance of CdSe sensitizers reflected a greater rate of electron transfer from the ascorbic acid (k Asc ). The observed difference in the QD-ascorbic acid charge transfer rates between the two QD materials was consistent with respective driving forces for these systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Structure–reactivity relationships in the removal efficiency of catechol and hydroquinone by structurally diverse Mn-oxides

Catechol and hydroquinone are widely present hydroxybenzene isomers in the natural environment that induce environmental toxicities. These hydroxybenzene compounds can be effectively removed by manganese (Mn)-oxides via sorption and oxidative degradation processes. In the present study, we investigated the structure–reactivity relationships in the sorption and oxidation of catechol and hydroquinone on Mn-oxide surfaces. Two widely present Mn-oxides, including hydrous Mn oxide (HMO) and cryptomelane, comprised of layer and tunnel structures, respectively, are specifically studied. Effects of Mn-oxide structures and environmental pH conditions on the removal efficiency of these hydroxybenzene compounds, via sorption and oxidative degradation, are investigated. Cryptomelane, which has a higher specific surface area than HMO, possesses a higher sorption and oxidation capacity. The complexation mechanisms of catechol and hydroquinone vary due to their structure-induced difference in reactivity. Catechol reduced and dissolved more Mn from Mn-oxides than hydroquinone, accompanied by a higher C loss of catechol-C, suggesting a higher reactivity of catechol. Structural changes occurred in the Mn-oxides resulting from reaction with catechol and hydroquinone: reduction of Mn(IV), corresponding formation of Mn(III) and Mn(II) in the mineral, and free Mn 2+ ions released into the suspension. Finally, these insights could help us better understand and predict the fate of hydroxybenzene compounds in Mn-oxide-rich soils and wastewater treatment systems that generate Mn-oxides via Mn removal and the associated environmental toxicity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sizing comingled CF/PA 6 fibers with cellulose nanofibrils for enhanced performance properties

Compatibility between the reinforcing phase and the polymer matrix is critical to achieving the desired mechanical and thermal performance of composite materials. Several mechanisms can enhance this interfacial interaction, including surface treatments (e.g., oxidation, plasma, or irradiation), in-situ nanoparticle deposition, and fiber sizing. Here, in this study, cellulose nanofibrils (CNF) were employed as a sustainable sizing agent to modify the interface in commingled carbon fiber (CF)/polyamide 6 (PA 6) yarns, in which CF and PA6 filaments are intimately blended to enable simultaneous consolidation. A 0.25 wt% CNF aqueous suspension was applied under bath sonication to ensure uniform dispersion and minimize agglomeration. CNF-sized and unsized yarns were used to fabricate unidirectional composite plates via filament winding on a flat mandrel, followed by compression molding. Scanning electron microscopy confirmed CNF presence on both CF and PA6 filaments. CNF-sized composites exhibited increments in interlaminar shear strength (ILSS) by 50%, flexural strength by 11%, and tensile strength by 2.5% compared to unsized composites. Thermal analysis showed minimal changes in degradation temperature and crystallinity. These findings demonstrate that CNF sizing enhances interfacial bonding and mechanical performance, offering a scalable and environmentally friendly strategy for thermoplastic composite manufacturing along with yarn/tow handleability.

Cellulose nanofibrils (CNF)↗
DOE OSTI2025

Stirring and peristaltic pumping alter flow electrode particle size and morphology

Flowable carbon-based electrodes are widely studied in electrochemical systems for energy storage and water treatment. Most laboratory- and pilot-scale studies employ active mixing for slurry preparation and handling and use peristaltic pumps for slurry circulation. Magnetic stirring is the most prevalent mixing method at the laboratory scale, and the combination of magnetic mixing and peristaltic pumping is favored for convenience and compatibility with particulate suspensions. However, these methods can strongly affect particle size and morphology (and therefore cell performance). In this study, we evaluate how mixing and pumping influence particle degradation in two commonly used carbon materials: spherical carbon black (CB) beads and powdered activated carbon (AC). We performed 24 h stirring-only experiments using magnetic, orbital, and overhead stirring. Separately, we conducted 32 h circulation experiments using a commercial peristaltic pump. Particle morphology and size were analyzed using optical microscopy and laser diffraction. The initially spherical CB beads (~580 μm, 1.5 wt%) exhibit rapid and extensive breakdown under both peristaltic pumping and magnetic stirring. By comparison, AC particles (initially ~31 μm) tested at 1.5 and 15 wt% showed measurable size reductions of up to ~25 % under either stirring or pumping. In conclusion, these findings highlight the need to account for and quantify morphological changes caused by both stirring and pumping in the design and associated evaluation of flowable electrode systems.

Chemistry↗
DOE OSTI2024

Effect of polyphenols on the rheology, microstructure and in vitro digestion of pea protein gels at various pH

Polyphenols exist widely in plants and interact with plant proteins distinctly depending on the environmental pH. This could potentially affect the gelling property of plant proteins and their digestion. In the present study, pea protein suspensions containing 0 %, 0.5 % and 1 % green tea polyphenols (GTP) were heated to form gels at pH5, pH7, and pH8.5. A strain amplitude sweep showed that the storage modulus (G’) and critical strain of pea protein gels decreased with increased GTP concentration at all examined pH. Gelation dynamic showed gelling of pea protein-GTP was delayed at pH7 and pH8.5 compared to the control. Differential scanning calorimetry showed that pea proteins became less heat resistant in the presence of GTP at pH5 and pH7, but not at pH8.5. Ultra-small and small-angle X-ray scattering showed that the radius of gyration of small- and medium-sized aggregates in pea protein gels was increased ~10–16 % and 22–30 % at pH7 and pH8.5, respectively when 1 % GTP was present. Finally, under such pH conditions, the proportion of structure with a radius of ~10–200 nm was increased in pea protein-GTP gels based on the volume size distribution. In vitro digestion found the soluble protein content of digesta of pea protein-GTP gels had a 5–8.5 % decrement with the presence of larger peptides when compared to pea protein gels.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Labile Fe(III) supersaturation controls nucleation and properties of product phases from Fe(II)-catalyzed ferrihydrite transformation

We report Fe(II)-catalyzed ferrihydrite (Fh) transformation to more crystalline iron (oxyhydr)oxide phases is a widely occurring geochemical process which has been extensively studied as a function of Fe(II)/Fh ratios at fixed Fh loadings. However, recent isolation of an intermediate Fe(III) species resulting from Fe(II)-Fh contact that facilitates transformation by dissolution/reprecipitation suggests that the kinetics and properties of product phases will instead depend mostly on its rate of accumulation to a critical concentration, consistent with principles in the classical nucleation theory (CNT). This suggests a dependence both on the loading of Fe(II) on the surface, which controls the rate of labile Fe(III) formation, as well as the available volume of solution, which also impacts how fast it can achieve its critical concentration to nucleate product phases. To specifically examine the latter effect, here we studied transformation of 15 mg Fh in 1 mM FeSO 4 solutions at pH 7.2 in batch suspensions of 30 mL, 150 mL, and 450 mL volumes. Time-dependent concentrations of aqueous Fe(II), surface-associated Fe(II), and resulting labile Fe(III) were monitored along with bulk solids characterization as a function of time. Transmission electron microscopy (TEM) was used to visualize the evolution of phases at identical locations on TEM grids. The collective results show that the rates of Fh loss and emergence of product lepidocrocite (Lp) and goethite (Gt) as well as their phase proportions, nucleation mode and morphological properties depend directly on the rate of accumulation of the labile Fe(III) precursor to its critical concentration, which in our experiments was controlled simply by varying the available volume of solution into which it enters. Statistical analyses of TEM image data suggest that while both heterogeneous and homogeneous nucleation occurred in all experiments, the former was increasingly favored at lower Fh/solution ratio due to its lower nucleation barrier being more favorable at attendant lower supersaturations of Fe(III).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Measured CO 2 sorption isotherms with 25 Bakken Petroleum System rock samples from the Lower and Upper Shales, Middle Bakken, and Three Forks formations

Isotherms were measured with 25 Bakken Petroleum System (BPS) rock samples using a magnetic suspension balance at reservoir conditions of 110 °C and pressures up to 345 bar. Samples from four wells represented the Middle Bakken (MB) and Three Forks (TF) production zones, and the Upper Bakken Shale (UBS) and Lower Bakken Shale (LBS) source shales. UBS and LBS CO 2 sorption capacities at 345 bar averaged 12–14 g/kg rock compared to 1.3 to 2.5 g/kg rock for MB and TF. Increasing pressure from 150 to 345 bar resulted in only small increases in CO 2 sorption for all lithofacies. For the UBS and LBS source shales, the higher average total organic carbon (TOC) values (14.7 and 11.4 wt.%) and clay values (25 and 28 wt.%) corresponded to their higher CO 2 sorption values while for the MB and TF samples, lower TOCs (0.3 and 0.5 wt.%) and clay values (8.2 and 18.2 wt.%) corresponded to lower CO 2 sorption values. Here, when all 25 samples (from all lithofacies) were evaluated as a group, sorption capacities were highly correlated with TOC (Spearman's rho values +0.84 to +0.85), with rock density (rho values -0.75 to -0.76), and clay content (rho values +0.66). However, correlations with porosity and thermal maturity (Tmax) were weak. Measured sorption capacities and rock porosities showed that sorption accounted for about 10-times as much CO 2 storage as the available pore space for the UBS and LBS lithofacies. In contrast, the pore space dominated the storage resource of the TF and MB lithofacies.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Aminated poly(ethylene glycol) methacrylate resins as stable heterogeneous catalysts for the aldol reaction in water

Amine functionalized silicas have frequently been investigated as potential aldol reaction catalysts. However, active site leaching due to hydrolysis cannot be avoided, limiting the long-term stability of these catalysts in aqueous aldol reactions. Therefore, novel catalysts based on an organic resin have been developed starting from a suspension polymerized poly(ethylene glycol) methacrylate (PEGMA) hydrogel with poly(ethylene glycol) dimethacrylate (PEGDMA) as cross-linker. Amine functionalization was performed by chlorination of the terminal hydroxyl groups in the resulting PEGMA resin and subsequent nucleophilic substitution with an amine precursor, i.e., ethylenediamine (EDA), N,N'-dimethylethylenediamine (DED), or methylamine (MA). Additionally, the successful synthesis of the catalysts was confirmed by 13C NMR, FT-IR, and elemental CHN analysis. Performance evaluation in a batch reactor for the aqueous aldol reaction of acetone with 4-nitrobenzaldehyde resulted in a turnover frequency (TOF) of the PEGMA-EDA catalyst amounting to 6.3 ± 0.4 · 10 -4 s -1 , which is of the same order of magnitude as that of the corresponding state-of-the-art amine functionalized silica evaluated using hexane as solvent. The PEGMA-DED catalyst exhibited a somewhat lower TOF of 3.1 ± 0.2 · 10 -4 s -1 , while the PEGMA-MA catalyst did not exhibit any turnover, indicating that the secondary amine in the backbone of the active site in the PEGMA-EDA catalyst is inactive. Continuous-flow evaluation of the PEGMA-EDA catalyst in a packed-bed reactor indicated that, as opposed to a primary amine functionalized silica catalyst, a stable catalytic activity as a function of time on stream could be achieved for at least 8 h and, hence, that no deactivation has occurred in this timeframe.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗