Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL SURFACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Flight Tests on U.S.S. Los Angeles. Part II : Stress and Strength Determination

The tests described in this report furnished data on the actual aerodynamic forces, and the resulting stresses and bending moments in the hull of the U. S. S. "Los Angeles" during as severe still-air maneuvers as the airship would normally be subjected to, and in straight flight during as rough air as is likely to occur in service, short of squall or storm conditions. The maximum stresses were found to be within the limits provided for in accepted practice in airship design. Normal flight in rough air was shown to produce forces and stresses about twice as great as the most severe still-air maneuvers. No light was thrown upon the forces which might occur in extreme or exceptional conditions, such as the storm which destroyed the "Shenandoah". The transverse aerodynamic forces on the hull proper were found to be small and irregular. Owing to the necessity of conserving helium, it was impossible to fly the airship in a condition of large excess of buoyancy or weight in order to determine the air pressure distribution at a fixed angle of pitch. However, there is every reason to believe that in that condition the forces on the actual airship are as close to the wind-tunnel results as can be determined by present type of pressure measuring apparatus. It is considered that most important data obtained are the coefficients of tail-surface forces and hull-bending moments. These are tabulated in this report.

Burgess, C P↗

Pressure-Distribution Measurements on the Hull and Fins of a 1/40-Scale Model of the U. S. Airship "Akron."

This report presents the results of measurements of pressure distribution conducted in the propeller-research wind tunnel of the National Advisory Committee for Aeronautics on a 1/40-scale model of the U. S. Airship "Akron" (ZRS-4). The pressures, which were measured simultaneously at nearly 400 orifices located at 26 stations along one side of the hull, were recorded by two photographic multiple manometers placed inside the model. The hull pressures were measured both with and without the tail surfaces and the control car for eight angles of pitch varying from 0 degree to 20 degrees and at air speeds of approximately 70 and 100 miles per hour. The pressures were also measured at approximately 160 orifices on one horizontal fin for the above speeds and pitch angles and for nine elevator angles.

Freeman, Hugh B↗

Pressure-Distribution Measurements at Large Angles of Pitch on Fins of Different Span-Chord Ratio on a 1/40-Scale Model of the U. S. Airship "Akron."

Report presents the results of pressure-distribution measurements on a 1/40-scale model of the U. S. Airship "Akron" conducted in the NACA 20-foot wind tunnel. The measurements were made on the starboard fin of each of four sets of horizontal tail surfaces, all of approximately the same area but differing in span-chord ratio, for five angles of pitch varying from 11.6 degrees to 34 degrees, for four elevator angles, and at air speeds ranging from 56 to 77 miles per hour. Pressures were also measured at 13 stations along the rear half of the port side of the hull at one elevator setting for the same five angles of pitch and at an air speed of approximately 91 miles per hour. The normal force on the fin and the moment of forces about the fin root were determined. The results indicate that, ignoring the effect on drag, it would be advantageous from structural considerations to use a fin of lower span-chord ratio than that used on the "Akron."

Mchugh, James G↗

Experimental Investigation of Wind-Tunnel Interference on the Downwash Behind an Airfoil

The interference of the wind-tunnel boundaries on the downwash behind an airfoil has been experimentally investigated and the results have been compared with the available theoretical results for open-throat wind tunnels. As in previous studies, the simplified theoretical treatment that assumes the test section to be an infinite free jet has been shown to be satisfactory at the lifting line. The experimental results, however, show that this assumption may lead to erroneous conclusions regarding the corrections to be applied to the downwash in the region behind the airfoil where the tail surfaces are normally located. The results of a theory based on the more accurate concept of the open-jet wind tunnel as a finite length of free jet provided with a closed exit passage are in good qualitative agreement with the experimental results.

Silverstein, Abe↗

An empirically derived basis for calculating the area, rate, and distribution of water-drop impingement on airfoils

An empirically derived basis for predicting the area, rate, and distribution of water-drop impingement on airfoils of arbitrary section is presented. The concepts involved represent an initial step toward the development of a calculation technique which is generally applicable to the design of thermal ice-prevention equipment for airplane wing and tail surfaces. It is shown that sufficiently accurate estimates, for the purpose of heated-wing design, can be obtained by a few numerical computations once the velocity distribution over the airfoil has been determined. The calculation technique presented is based on results of extensive water-drop trajectory computations for five airfoil cases which consisted of 15-percent-thick airfoils encompassing a moderate lift-coefficient range. The differential equations pertaining to the paths of the drops were solved by a differential analyzer.

Bergrun, Norman R↗

Charts relating the compressive buckling stress of longitudinally supported plates to the effective deflectional and rotational stiffness of the supports

A stability analysis is made of a long flat rectangular plate subjected to a uniform longitudinal compressive stress and supported along its longitudinal edges and along one or more longitudinal lines by elastic line supports. The elastic supports possess deflectional and rotational stiffness. Such configuration is an idealization of the compression cover skin and internal structure of a wing and tail surfaces. The results of the analysis are presented in the form of charts in which the buckling-stress coefficient is plotted against the buckle length of the plate for a wide range of support stiffnesses. The charts make possible the determination of the compressive buckling stress of plates supported by members whose stiffness may or may not be defined by elementary beam bending and twisting theory but yet whose effective restraint is amenable to evaluation. The deflectional and rotational stiffness provided by longitudinal stiffeners and full-depth webs is discussed and numerical examples are given to illustrate the application of the charts to the design of wing structures.

Anderson, Roger A↗

An Experimental Investigation of Reduction in Transonic Drag Rise at Zero Lift by the Addition of Volume to the Fuselage of a Wing-body-tail Configuration and a Comparison with Theory

An experimental investigation was made by the free-fall recoverable-model technique to assess at zero lift the possibilities of reducing the drag-rise coefficients of a wing-body-cruciform-tail combination by adding volume to the fuselage. The basic features of the test model were an unswept aspect-ratio-3.1 thin wing, a fineness-ratio-12.4 fuselage, and four 45 degrees sweptback tail surfaces. The tests covered a Mach number range of 0.84 to 1.15 with Reynolds numbers of 6.000.000 to 14,000,000, based on the wing mean aerodynamic chord. Considerable reduction in drag-rise coefficient was effected for several different modifications by the addition of properly distributed volume to the fuselage. In one instance, a reduction in drag coefficient was obtained by adding a volume which was almost four times the exposed wing volume. The computation method presented in NACA RM A53H17 generally predicted the supersonic drag-rise coefficients for each modification within 20 percent of the experimental values. As in the above-mentioned report, the predictions at a Mach number of one were not accurate. The changes in drag-rise coefficients resulting from the modifications were generally predicted with better accuracy than the values of drag-rise coefficients.

Holdaway, George H↗

Free-spinning-tunnel Tests of a 1/26th Scale Model of the Douglas XTB2D-1 Airplane

A spin-tunnel investigation of a 1/26 scale model of the Douglas XTB2D-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements upon the erect- and inverted-spin and recovery characteristics of the model were determined for various loading conditions. Tests were also performed to determine the effects of various tail modifications. The investigation included emergency spin-recovery parachute tests as well as crew-escape and rudder- and elevator-force tests. All tests were performed at an equivalent spin altitute of 20,000 feet. The recovery characteristics of the model in the original design were found to be unsatisfactory. Installation of a large ventral fin, installation of tip fins on the horizontal tail, or installation of a small ventral fin in combination with antispan fillets and a spanwise extension of the horizontal-tail surfaces satisfactorily improved the recovery characteristics of the model.

Stone, Ralph W↗

Effect of fuselage and engine nacelles on some aerodynamic properties of an airplane wing

With the aid of the method of J. Lotz, the writer undertook to solve theoretically the lift distribution along the span of an airplane wing, when the outline of the wing is uneven. This problem arises in the case of a mid-wing monoplane with embedded engine nacelles. The fuselage and the nacelles were considered as aerodynamically profiled, that is, as lift-producing parts. The task was therefore to determine not only the disturbance caused by the fuselage and nacelles, but also their share in the total lift of the wing. After the above-mentioned calculations, the induced velocity, due to the vortex system by which the wing was replaced, was also calculated and measured at the points corresponding, in an airplane, to the location of the horizontal tail surfaces.

Vladea, Joan↗

The aerodynamic wind vane and the inherent stability of airplanes

The design of the wind vane described rests on the following line of reasoning: An airplane, originally in equilibrium about its C.G. is assumed to be deflected from this position through an angle (delta)i, the variation (delta)i being so sudden that the path of the C.G. and the airplane speed do not change while it is taking place. The aerodynamic forces acting on the wings, tail surfaces, fuselage, etc., which, as a whole, exerted a zero moment (M(sub G) = 0) about the center of gravity at the instant of equilibrium, now exert a moment M(sub G) not equal to 0.

Lapresle, A↗

The airplane: A simulated commercial air transportation study

The 'Airplane' is a moderate-range, 70 passenger aircraft. It is designed to serve demands for flights up to 10,000 feet and it cruises at 32 ft/s. The major drivers for the design of the Airplane are economic competitiveness, takeoff performance, and weight minimization. The Airplane is propelled by a single Astro 15 electric motor and a Zinger 12-8 propeller. The wing section is a Spica airfoil which, because of its flat bottom, provides simplicity in manufacturing and thus helps to cut costs. The wing is constructed of a single load bearing mainspar and shape-holding ribs coated with Monokote skin, lending to a light weight structural makeup. The fuselage houses the motor, flight deck and passenger compartments as well as the fuel and control actuating systems. The wing will be attached to the top of the fuselage as will the fuel and control actuator systems for easy disassembly and maintenance. The aircraft is maneuvered about its pitch axis by means of an aft elevator on the flat plate horizontal tail. The twin vertical tail surfaces are also flat plates and each features a rudder for both directional and roll control. Along with wing dihedral, the rudders will be used to roll the aircraft. The Airplane is less costly to operate at its own maximum range and capacity as well as at its maximum range and the HB-40's maximum capacity than the HB-40.

Dauteuil, Mark↗

Aircraft empennage structural detail design

The purpose of this project is to provide an empennage structural assembly that will withstand the operational loads defined in FAR Part 23, as well as those specified in the statement of work, i.e. snow, rain, humidity, tiedown forces, etc. The goal is to provide a simple yet durable lightweight structure that will transfer the aerodynamic forces produced by the tail surfaces through the most efficient load path to the airframe. The structure should be simple and cost-effective to manufacture and repair. All structures meet or exceed loading and fatigue criteria. The structure provides for necessary stiffness and ease of maintenance.

Lesnewski, David↗

Predictions Of Accretion Of Ice On A Commercial Airplane

Report presents computational study of accretion of ice on wings and on horizontal tail surfaces of simplified version of Boeing 737 airplane. Calculations performed by use of LEWICE3D computer code, which incorporates panel-method mathematical model of three-dimensional potential flow and mathematical models of trajectories of drops of water entrained in flow, impingement of drops on surfaces, and transfer of heat.

Bidwell, C. S.↗

Subsonic Flight Tests of a 1/7-Scale Radio-Controlled Model of the North American X-15 Airplane with Particular Reference to High Angel-of-Attack Conditions

An investigation of the subsonic stability and control characteristics of an unpowered 1/7-scale model based on the North American X-15 airplane was conducted by using a radio-controlled model launched from a helicopter and flown in free-gliding flight. At angles of attack below about 20 deg. where the model motions represent those of the X-15 airplane, the model was found to be both longitudinally and laterally stable, and the all-movable tail surfaces were found to be very effective. The model could also be flown at much higher angles of attack where the model motions did not necessarily represent those of the airplane because of slight geometrical differences and Reynolds number effects, but these test results are useful in evaluating the effectiveness at these angles of the type of lateral control system used in the X-15 airplane. In some cases, the model was flown to angles of attack as high as 60 or 70 deg. without encountering divergent or uncontrollable conditions. For some flights in which the model was subjected to rapid maneuvers, spinning motions were generated by application of corrective controls to oppose the direction of rotation. Rapid recoveries from this type of motion were achieved by applying roll control in the direction of rotation.

Hewes, Donald E.↗

Free-Spinning-Tunnel Investigation of a 1/20-Scale Model of an Unswept-Wing Jet-Propelled Trainer Airplane

A flutter analysis employing the kernel function for three- dimensional, subsonic, compressible flow is applied to a flutter-tested tail surface which has an aspect ratio of 3.5, a taper ratio of 0.15, and a leading-edge sweep of 30 deg. Theoretical and experimental results are compared at Mach numbers from 0.75 to 0.98. Good agreement between theoretical and experimental flutter dynamic pressures and frequencies is achieved at Mach numbers to 0.92. At Mach numbers from 0.92 to 0.98, however, a second solution to the flutter determinant results in a spurious theoretical flutter boundary which is at a much lower dynamic pressure and at a much higher frequency than the experimental boundary.

Bowman, James S., Jr.↗

Ice Accretion Calculations for a Commercial Transport Using the LEWICE3D, ICEGRID3D and CMARC Programs

Collection efficiency and ice accretion calculations were made for a commercial transport using the NASA Lewis LEWICE3D ice accretion code, the ICEGRID3D grid code and the CMARC panel code. All of the calculations were made on a Windows 95 based personal computer. The ice accretion calculations were made for the nose, wing, horizontal tail and vertical tail surfaces. Ice shapes typifying those of a 30 minute hold were generated. Collection efficiencies were also generated for the entire aircraft using the newly developed unstructured collection efficiency method. The calculations highlight the flexibility and cost effectiveness of the LEWICE3D, ICEGRID3D, CMARC combination.

Bidwell, Colin S.↗

An Airplane Design having a Wing with Fuselage Attached to Each Tip

This paper describes the conceptual design of an airplane having a low aspect ratio wing with fuselages that are attached to each wing tip. The concept is proposed for a high-capacity transport as an alternate to progressively increasing the size of a conventional transport design having a single fuselage with cantilevered wing panels attached to the sides and tail surfaces attached at the rear. Progressively increasing the size of conventional single body designs may lead to problems in some area's such as manufacturing, ground-handling and aerodynamic behavior. A limited review will be presented of some past work related to means of relieving some size constraints through the use of multiple bodies. Recent low-speed wind-tunnel tests have been made of models representative of the inboard-wing concept. These models have a low aspect ratio wing with a fuselage attached to each tip. Results from these tests, which included force measurements, surface pressure measurements, and wake surveys, will be presented herein.

Spearman, Leroy M.↗

Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Hunton, Lynn W.↗