Results for “Tensile strength” — Page 14

NASA NTRS1985

Making Stronger Twine With Matched Strands

Higher tensil strength achieved with same production equipment. Strong twine made by using spools in one of two-step manufacturing process. Three primary strands twisted together in opposite direction to form threeply twine. Technique used successfully in manufacture of safety netting with 600- to 700-lb (2,700-to 3,100-N) tensil strength and 60-ton (54 x 10 to third power kg) tuna seine with area of 86 acres (3.5 x 10 to fifth power m2). Increase in tensil strength of completed twine found experimentally 10 to 12 percent.

Kirkland, W. L.↗

NASA NTRS2003

Cryogenic Temperature-Gradient Foam/Substrate Tensile Tester

The figure shows a fixture for measuring the tensile strength of the bond between an aluminum substrate and a thermally insulating polymeric foam. The specimen is meant to be representative of insulating foam on an aluminum tank that holds a cryogenic liquid. Prior to the development of this fixture, tensile tests of this type were performed on foam/substrate specimens immersed in cryogenic fluids. Because the specimens were cooled to cryogenic temperatures throughout their thicknesses, they tended to become brittle and to fracture at loads below true bond tensile strengths. The present fixture is equipped to provide a thermal gradient from cryogenic temperature at the foam/substrate interface to room temperature on the opposite foam surface. The fixture includes an upper aluminum block at room temperature and a lower aluminum block cooled to -423 F (approx. -253 C) by use of liquid helium. In preparation for a test, the metal outer surface (the lower surface) of a foam/substrate specimen is bonded to the lower block and the foam outer surface (the upper surface) of the specimen is bonded to the upper block. In comparison with the through-the-thickness cooling of immersion testing, the cryogenic-to-room-temperature thermal gradient that exists during testing on this fixture is a more realistic approximation of the operational thermal condition of sprayed insulating foam on a tank of cryogenic liquid. Hence, tensile tests performed on this fixture provide more accurate indications of operational bond tensile strengths. In addition, the introduction of the present fixture reduces the cost of testing by reducing the amount of cryogenic liquid consumed and the time needed to cool a specimen.

Vailhe, Christophe↗

DOE OSTI2022

Impact of biomass ash content on biocomposite properties

Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). Furthermore, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0–7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.

36 MATERIALS SCIENCE↗

NASA NTRS1991

Properties of novel CVD graphite fibers and their bromine intercalation compounds

A hybrid fiber with a PAN core surrounded by a vapor grown carbon fiber (VGCF) sheath was fabricated using a proprietary process. The density, ultimate tensile strength, Young's modulus, and resistivity of pristine and bromine intercalated fibers made by this technique having diameters varying from 5 to 50 microns were compared with the values predicted from the rule of mixtures model. For both the pristine and intercalated fibers, the density, ultimate tensile strength, and Young's modulus of the fibers were lower than predicted, but the resistivity was measured to be consistent with predictions. The lower than theoretical mechanical properties may be evidence of a low density disordered interface between the core and the sheath which would lower the density and degrade the mechanical properties, but would leave the resistivity nearly unaffected. Intercalation had little if any effect on the ultimate tensile strength and Young's modulus, but raised the density by about 11 pct., and lowered the resistivity by an order of magnitude. The diameter dependence of the resistivity showed evidence of a depletion layer of the type found in VGCF.

Gaier, James R.↗

NASA NTRS1992

Properties of hybrid CVD/PAN graphite fibers and their bromine intercalation compounds

A hybrid fiber with a PAN core surrounded by a vapor grown carbon fiber (VGCF) sheath was fabricated using a proprietary process. The density, ultimate tensile strength, Young's modulus, and resistivity of pristine and bromine intercalated fibers made by this technique having diameters varying from 5 to 50 microns were compared with the values predicted from the rule of mixtures model. For both the pristine and intercalated fibers, the density, ultimate tensile strength, and Young's modulus of the fibers were lower than predicted, but the resistivity was measured to be consistent with predictions. The lower than theoretical mechanical properties may be evidence of a low density disordered interface between the core and the sheath which would lower the density and degrade the mechanical properties, but would leave the resistivity nearly unaffected. Intercalation had little if any effect on the ultimate tensile strength and Young's modulus, but raised the density by about 11 pct., and lowered the resistivity by an order of magnitude. The diameter dependence of the resistivity showed evidence of a depletion layer of the type found in VGCF.

Gaier, James R.↗

NASA NTRS1985

Options for improving rigidized ceramic heatshields

Studies regarding capabilities, tensile strength, and dimensional stability of fibrous ceramics, used in current thermal protection systems and those required for future NASA advanced transfer vehicles, are presented. It is shown that the use of smaller diameter (2-4 micron) aluminoborosilicate fibers (instead of conventional 11-micron size) in the FRCI composites improves the homogeneity and tensile strength of high-silica composite. Substitution of the smaller aluminoborosilicate fibers by 2-4-micron alumina fibers in the AETB composites improves the dimensional stability, at the expense of a substantial increase in the thermal expansion coefficient, with a potential decrease in tensile strength.

Leiser, D. B.↗

NASA NTRS1951

Wire Cloth as Porous Material for Transpiration-cooled Walls

The permeability characteristics and tensile strength of a porous material developed from stainless-steel corduroy wire cloth for use in transpiration-cooled walls where the primary stresses are in one direction were investigated. The results of this investigation are presented and compared with similar results obtained with porous sintered metal compacts. A much wider range of permeabilities is obtainable with the wire cloth than with the porous metal compacts considered and the ultimate tensile strength in the direction of the primary stresses for porous materials produced from three mesh sizes of wire cloth are from two to three times the ultimate tensile strengths of the porous metal compacts.

MATERIALS - TYPES↗

DOE OSTI2024

Effect of plasma treatment on LMPAEK/CF tape and composites manufactured by automated tape placement (ATP)

Automated tape placement (ATP) process is widely used in aerospace for its advanced process control and multi-axis capabilities but faces issues like limited choice of materials and suboptimal tape consolidation. This study investigates air plasma treatment on ATP carbon fiber thermoplastic feedstock tape to address these challenges. The effects on low melt Polyaryletherketone/carbon fiber unidirectional tape (LMPAEK/CF UD tape) were analyzed. Treated and untreated tapes were used to fabricate composites and evaluated for physical, thermal, mechanical, and interfacial properties. Atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) analyses revealed surface roughness changes (on LMPAEK), extent of oxidation, and the presence of hydroxyl/carboxyl groups. Composites from plasma-treated tapes showed a 7.6% increase in tensile strength, 8% in tensile modulus, 18% in flexural strength, and 8.3% in flexural modulus. Further, the interlaminar shear strength improved by 18.7%. Failure analysis showed untreated composites failed via inter-ply and fiber-matrix delamination, while treated composites experienced matrix cracking and fiber breakage. This study highlights atmospheric plasma treatment as a solution to ATP’s limitations, significantly enhancing LMPAEK/CF UD tape composites’ properties.

36 MATERIALS SCIENCE↗

NASA NTRS1976

Tensile behavior of unnotched and notched tungsten-copper laminar composites

Relations were studied between the tensile strengths of unnotched and of notched, and elastic moduli of unnotched laminar sheet or foil composites and the amounts of reinforcement. Tungsten was used as the reinforcement and copper as the matrix, and the tests were run at room temperature. Three thicknesses of tungsten (i.e., 0.00254, 0.0127, and 0.0254 cm (0.001, 0.005, and 0.010 in) were used and the nominal volume fraction of tungsten was varied from about 0.05 to 0.95. It was found that the tensile strength of the unnotched specimens could be related to the amount of reinforcement, as could the elastic moduli, and that these values could be predicted by use of the rule of mixtures. The tensile strengths of the notched laminar composites could be predicted by use of the rule of mixtures using strengths for notched constituents, provided notch effects did not predominate.

Hoffman, C. A.↗

NASA NTRS2017

Ultraviolet Testing of Space Suit Materials for Mars

Human missions to Mars may require radical changes in the approach to extra-vehicular (EVA) suit design. A major challenge is the balance of building a suit robust enough to complete multiple EVAs under intense ultraviolet (UV) light exposure without losing mechanical strength or compromising the suit's mobility. To study how the materials degrade on Mars in-situ, the Jet Propulsion Laboratory (JPL) invited the Advanced Space Suit team at NASA's Johnson Space Center (JSC) to place space suit materials on the Scanning Habitable Environments with Raman & Luminescence for Organics and Chemicals (SHERLOC) instrument's calibration target of the Mars 2020 rover. In order to select materials for the rover and understand the effects from Mars equivalent UV exposure, JSC conducted ground testing on both current and new space suit materials when exposed to 2500 hours of Mars mission equivalent UV. To complete this testing, JSC partnered with NASA's Marshall Space Flight Center to utilize their UV vacuum chambers. Materials tested were Orthofabric, polycarbonate, Teflon, Dacron, Vectran, spectra, bladder, nGimat coated Teflon, and nGimat coated Orthofabric. All samples were measured for mass, tensile strength, and chemical composition before and after radiation. Mass loss was insignificant (less than 0.5%) among the materials. Most materials loss tensile strength after radiation and became more brittle with a loss of elongation. Changes in chemical composition were seen in all radiated materials through Spectral Analysis. Results from this testing helped select the materials that will fly on the Mars 2020 rover. In addition, JSC can use this data to create a correlation to the chemical changes after radiation-which is what the rover will send back while on Mars-to the mechanical changes, such as tensile strength.

Larson, Kristine↗

NASA NTRS2017

Ultraviolet Testing of Space Suit Materials for Mars

Human missions to Mars may require radical changes in the approach to extra-vehicular (EVA) suit design. A major challenge is the balance of building a suit robust enough to complete multiple EVAs under intense ultraviolet (UV) light exposure without losing mechanical strength or compromising the suit's mobility. To study how the materials degrade on Mars in-situ, the Jet Propulsion Laboratory (JPL) invited the Advanced Space Suit team at NASA's Johnson Space Center (JSC) to place space suit materials on the Scanning Habitable Environments with Raman & Luminescence for Organics and Chemicals (SHERLOC) instrument's calibration target of the Mars 2020 rover. In order to select materials for the rover and understand the effects from Mars equivalent UV exposure, JSC conducted ground testing on both current and new space suit materials when exposed to 2500 hours of Mars mission equivalent UV. To complete this testing, JSC partnered with NASA's Marshall Space Flight Center to utilize their UV vacuum chambers. Materials tested were Orthofabric, polycarbonate, Teflon, Dacron, Vectran, spectra, bladder, nGimat coated Teflon, and nGimat coated Orthofabric. All samples were measured for mass, tensile strength, and chemical composition before and after radiation. Mass loss was insignificant (less than 0.5%) among the materials. Most materials loss tensile strength after radiation and became more brittle with a loss of elongation. Changes in chemical composition were seen in all radiated materials through Spectral Analysis. Results from this testing helped select the materials that will fly on the Mars 2020 rover. In addition, JSC can use this data to create a correlation to the chemical changes after radiation-which is what the rover will send back while on Mars-to the mechanical changes, such as tensile strength.

Larson, Kristine↗

NASA NTRS1946

The column strength of aluminum alloy 75S-T extruded shapes

Because the tensile strength and tensile yield strength of alloy 75S-T are appreciably higher than those of the materials used in the tests leading to the use of the straight-line column curve, it appeared advisable to establish the curve of column strength by test rather than by extrapolation of relations determined empirically in the earlier tests. The object of this investigation was to determine the curve of column strength for extruded aluminum alloy 75S-T. In addition to three extruded shapes, a rolled-and-drawn round rod was included. Specimens of various lengths covering the range of effective slenderness ratios up to about 100 were tested.

COLUMNS, ALUMINUM-ALLOY - ALCOA 75ST - STRENGTH↗

NASA NTRS2013

The Effect of Fiber Strength Stochastics and Local Fiber Volume Fraction on Multiscale Progressive Failure of Composites

Continuous fiber unidirectional polymer matrix composites (PMCs) can exhibit significant local variations in fiber volume fraction as a result of processing conditions that can lead to further local differences in material properties and failure behavior. In this work, the coupled effects of both local variations in fiber volume fraction and the empirically-based statistical distribution of fiber strengths on the predicted longitudinal modulus and local tensile strength of a unidirectional AS4 carbon fiber/ Hercules 3502 epoxy composite were investigated using the special purpose NASA Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC); local effective composite properties were obtained by homogenizing the material behavior over repeating units cells (RUCs). The predicted effective longitudinal modulus was relatively insensitive to small (~8%) variations in local fiber volume fraction. The composite tensile strength, however, was highly dependent on the local distribution in fiber strengths. The RUC-averaged constitutive response can be used to characterize lower length scale material behavior within a multiscale analysis framework that couples the NASA code FEAMAC and the ABAQUS finite element solver. Such an approach can be effectively used to analyze the progressive failure of PMC structures whose failure initiates at the RUC level. Consideration of the effect of local variations in constituent properties and morphologies on progressive failure of PMCs is a central aspect of the application of Integrated Computational Materials Engineering (ICME) principles for composite materials.

multiscale analysis↗

NASA NTRS1997

Probabilistic Approaches: Composite Design

Probabilistic composite design is described in terms of a computational simulation. This simulation tracks probabilistically the composite design evolution from constituent materials, fabrication process through composite mechanics, and structural component. Comparisons with experimental data are provided to illustrate selection of probabilistic design allowables, test methods/specimen guidelines, and identification of in situ versus pristine strength. For example, results show that: in situ fiber tensile strength is 90 percent of its pristine strength; flat-wise long-tapered specimens are most suitable for setting ply tensile strength allowables; a composite radome can be designed with a reliability of 0.999999; and laminate fatigue exhibits wide spread scatter at 90 percent cyclic-stress to static-strength ratios.

Chamis, Christos C.↗

NASA NTRS1997

Probabilistic Composite Design

Probabilistic composite design is described in terms of a computational simulation. This simulation tracks probabilistically the composite design evolution from constituent materials, fabrication process, through composite mechanics and structural components. Comparisons with experimental data are provided to illustrate selection of probabilistic design allowables, test methods/specimen guidelines, and identification of in situ versus pristine strength, For example, results show that: in situ fiber tensile strength is 90% of its pristine strength; flat-wise long-tapered specimens are most suitable for setting ply tensile strength allowables: a composite radome can be designed with a reliability of 0.999999; and laminate fatigue exhibits wide-spread scatter at 90% cyclic-stress to static-strength ratios.

Chamis, Christos C.↗

NASA NTRS1979

Development and Evaluation of Elastomeric Materials for Geothermal Applications

A material was formulated having about 250-350 psi tensile strength and 30-80 percent elongation at 260 C for at least 24 hours in simulated brine. The relationship between these laboratory test results and sealing performance in actual or simulated test conditions is not entirely clear; however, it is believed that no conventional formation or casing packer design is likely to perform well using these materials. The synthetic effort focused on high temperature block copolymers and development of curable polystyrene. Procedures were worked out for synthesizing these new materials. Initial results with heat-cured unfilled polystyrene 'gum' at 260 C indicate a tensile strength of about 50 psi. Cast films of the first sample of polyphenyl quinoxaline-polystyrene block copolymer, which has 'graft-block' structure consisting of a polystyrene chain with pendant polyphenyl quinoxaline groups, show elastomeric behavior in the required temperature range. Its tensile strength and elongation at 260 C were 220-350 psi and 18-36 percent, respectively. All of these materials also showed satisfactory hydrolytic stability.

Mueller, W. A.↗

NASA NTRS2018

Undirectional Carbon Nanotube Yarn/Polymer Composites

Carbon nanotubes (CNTs) are one-dimensional nanomaterials with outstanding electrical and thermal conductivities and mechanical properties at the nanoscale. With these superior physical properties, CNTs are very attractive materials for future light weight structural aerospace applications. Recent manufacturing advances have led to the availability of bulk formats of CNTs such as yarns, tapes, and sheets in commercial quantities, thus enabling the development of macroscale composite processing methods for aerospace applications. The fabrication of unidirectional CNT yarn/polymer composites and the effect of processing parameters such as resin type, number of CNT yarn layers, CNT yarn/resin ratio, consolidation method, and tension applied during CNT yarn winding on the mechanical properties of unidirectional CNT yarn composites are reported herein. Structural morphologies, electrical and thermal conductivities, and mechanical performance of unidirectional CNT yarn/polymer composites under tensile and short beam shear loads are presented and discussed. The application of higher tension during the winding process and elevated cure pressure during the press molding step afforded a compact structural morphology and reduced void content in the composite. However, the composite tensile strength was negligibly impacted by the fabrication parameters, such as cure pressure, winding tension, and resin chemistry, excepting resin content and number of CNT yarn layers. The tension winding method produced better quality and lower resin content CNT yarn composites compared to conventional prepregging methods, resulting in higher specific strength and modulus of the composites. The specific tensile strength of the CNT composite was approximately 69 % of the starting CNT yarn. Electrical and thermal conductivities of unidirectional CNT yarn/polymer composites were in the range of 1000 to 12000 S/cm and 22 to 45 W/mK, respectively.

Kim, Jae-Woo↗

NASA NTRS1976

Development of sputtered techniques for thrust chambers

Procedures for closing out coolant passages in regeneratively cooled thrust chambers by triode sputtering, using post and hollow Cu-0.15 percent Zr cathodes are described. The effects of aluminum composite filler materials, substrate preparation, sputter cleaning, substrate bias current density and system geometry on closeout layer bond strength and structure are evaluated. High strength closeout layers were sputtered over aluminum fillers. The tensile strength and microstructure of continuously sputtered Cu-0.15 percent Zr deposits were determined. These continuous sputtered deposits were as thick as 0.75 cm. Tensile strengths were consistently twice as great as the strength of the material in wrought form.

Mullaly, J. R.↗