Search NASA⌕ Search

SEARCH · Search NASA

Results for “VTOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Rotary-wing aeroelasticity with application to VTOL vehicles

A concise assessment is presented of the state of the art in the field of rotary-wing aeroelasticity (RWE). The basic ingredients of RWE are reviewed, including structural modeling, unsteady aerodynamic modeling, formulation of the equations of motion, and solution methods. Results illustrating these methods are presented for isolated blades and coupled rotor-fuselage problems. The application of active controls to suppress aeromechanical and aeroelastic instabilities and to reduce vibration in rotorcraft is discussed. Structural optimization with aeroelastic constraints, gust response analysis of helicopters, and aeroelastic problems in special VTOL vehicles are briefly examined.

Friedmann, Peretz P.↗

Flow visualization studies of VTOL aircraft models during Hover in ground effect

A flow visualization study of several configurations of a jet-powered vertical takeoff and landing (VTOL) aircraft model during hover in ground effect was conducted. A surface oil flow technique was used to observe the flow patterns on the lower surfaces of the model. There were significant configuration effects. Wing height with respect to fuselage, the presence of an engine inlet duct beside the fuselage, and nozzle pressure ratio are seen to have strong effects on the surface flow angles on the lower surface of the wing. This test was part of a program to improve the methods for predicting the hot gas ingestion (HGI) for jet-powered vertical/short takeoff and landing (V/STOL) aircraft. The tests were performed at the Jet Calibration and Hover Test (JCAHT) Facility at Ames Research Center.

Mourtos, Nikos J.↗

Rocket-based combined-cycle (RBCC) powered spaceliner class vehicle can advantageously employ vertical takeoff and landing (VTOL)

The subject is next generation orbital space transporation, taken to be fully reusable non-staged 'aircraft like' systems targeted for routine, affordable access to space. Specifically, the takeoff and landing approach to be selected for such systems is considered, mainly from a propulsion viewpoint. Conventional wisdom has it that any transatmospheric-class vehicle which uses high-speed airbreathing propulsion modes (e.g., scramjet) intrinsically must utilize horizontal takeoff and landing, HTOHL. Although this may be true for all-airbreathing propulsion (i.e., no rocket content as in turboramjet propulsion), that emerging class of powerplant which integrally combines airbreathing and rocket propulsion, referred to as rocket-based combined-cycle (RBCC) propulsion, is considerably more flexible with respect to selecting takeoff/landing modes. In fact, it is proposed that any of the modes of interest may potentially be selected: HTOHL, VTOHL, VTOVL. To illustrate this surmise, the case of a previously documented RBCC-powered 'Spaceliner' class space transport concept, which is designed for vertical takeoff and landing, is examined. The 'RBCC' and 'Spaceliner' categories are first described for background. Departing form an often presumed HTOHL baseline, the leading design and operational advantages of moving to VTOVL are then elucidated. Technical substantiation that the RBCC approach, in fact, enables this capability (but also that of HTOHL and VTOVL) is provided, with extensive reference to case-in-point supporting studies. The paper closes with a set of conditional surmises bearing on its set of conclusions, which point up the operational cost advantages associated with selecting the vertical takeoff and landing mode combination (VTOL), uniquely offered by RBCC propulsion.

Escher, William J. D.↗

Investigation of Longitudinal and Lateral Stability Characteristics of a Six-Propeller Deflected-Slipstream VTOL Model with Boundary-Layer Control Including Effects of Ground Proximity

An investigation of the longitudinal and lateral stability and control and Performance characteristics of a six-propeller deflected- slipstream vertical-take-off-and-landing (VTOL) model in the transition speed range was conducted in the 17-foot test section of the Langley 300-MPH 7- by 10-foot tunnel. A complete analysis of the data was not conducted. A modest amount of blowing boundary-layer control was necessary to achieve transition without wing stall.

Grunwald, Kalman J.↗

A Flight Study of the Conversion Maneuver of a Tilt-Duct VTOL Aircraft

Flight records are presented from an early flight test of a wing-tip mounted tilting-ducted-fan, vertical-take-off and landing (VTOL) aircraft configuration. Time histories of the aircraft motions, control positions, and duct pitching-moment variation are presented to illustrate the characteristics of the aircraft in hovering, in conversion from hovering to forward flight, and in conversion from forward flight to hovering. The results indicate that during essentially continuous slow level- flight conversions, this aircraft experiences excessive longitudinal trim changes. Studies have shown that the large trim changes are caused primarily by the variation of aerodynamic moments acting on the duct units. Action of the duct-induced downwash on the horizontal stabilizer during the conversion also contributes to the longitudinal trim variations. Time histories of hovering and slow vertical descent in the final stages of landing in calm air show angular motions of the aircraft as great as +/- 10 deg. about all axes. Stick and pedal displacements required to control the aircraft during the landing maneuver were on the order of 50 to 60 percent of the total travel available.

Tapscott, Robert J.↗

Lateral Stability and Control Characteristics of a Four-Propeller Deflected-Slipstream VTOL Model Including the Effects of Ground Proximity

The investigation of the lateral-directional stability and control characteristics of a four-propeller deflected-slipstream VTOL model in the transition speed range was conducted in the 17-foot test section of the Langley 300-MPH 7- by 10-foot tunnel. A large fairing on top of the rear fuselage was needed to eliminate directional instability in the power-off flaps-retracted condition. Even with this fairing some instability at small sideslip angles remained for power-on conditions with low flap deflections. The configuration exhibited a high level of dihedral effect which, coupled with the directional instability, will probably produce an undesirable Dutch roll oscillation.

Kuhn, Richard E.↗

Longitudinal Aerodynamic Characteristics of a Four-Propeller Deflected Slipstream VTOL Model Including the Effects of Ground Proximity

Results are presented of a wind-tunnel investigation of the longitudinal stability, control, and performance characteristics of a model of a four-propeller deflected-slipstream VTOL airplane in the transition speed range. These results indicate that steady level-flight transition and descending flight-path angles up to 7 or 8 deg. out of the region of ground effect can be accomplished without wing stall being encountered. In general, the pitching moments out of ground proximity can be adequately trimmed by programming the stabilizer incidence to increase with increasing flap deflection, except for a relatively large diving moment in the hovering condition. The deflection of the slipstream onto the horizontal tail in proximity of the ground substantially increases the diving moment in hovering, unless the tail is set at a large nosedown incidence.

Kuhn, Richard E.↗

Hovering and Transition Flight Tests of a 1/5-Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/5-scale flying model of a jet-powered vertical-attitude VTOL research airplane in hovering and transition flight. The model was powered with either a hydrogen peroxide rocket motor or a compressed-air jet exhausting through an ejector tube to simulate the turbojet engine of the airplane. The gyroscopic effects of the engine were simulated by a flywheel driven by compressed-air jets. In hovering flight the model was controlled by jet-reaction controls which consisted of a swiveling nozzle on the main jet and a movable nozzle on each wing tip; and in forward flight the model was controlled by elevons and a rudder. If the gyroscopic effects of the jet engine were not represented, the model could be flown satisfactorily in hovering flight without any automatic stabilization devices. When the gyroscopic effects of the jet engine were represented, however, the model could not be controlled without the aid of artificial stabilizing devices because of the gyroscopic coupling of the yawing and pitching motions. The use of pitch and yaw dampers made these motions completely stable and the model could then be controlled very easily. In the transition flight tests, which were performed only with the automatic pitch and yaw dampers operating, it was found that the transition was very easy to perform either with or without the engine gyroscopic effects simulated, although the model had a tendency to fly in a rolled and sideslipped attitude at angles of attack between approximately 25 and 45 deg because of static directional instability in this range.

Smith, Charles C., Jr.↗

Aerodynamic Characteristics of a Four-Propeller Tilt-Wing VTOL Model with Twin Vertical Tails, Including Effects of Ground Proximity

Results are presented of a wind-tunnel investigation of the aerodynamic stability, control, and performance characteristics of a model of a four-propeller tilt-wing VTOL airplane employing flaps and speed brakes through the transition speed range. The results indicate that the wing was stalled for steady level flight for all conditions of the investigation; however, the flapped configuration did produce a higher maximum lift. The effectiveness of the flap in delaying the stall in the present investigation was not as great as in some previous investigations because the flap used was smaller than that used previously. The wing stall resulted in an appreciable reduction of aileron effectiveness during the transition. Out of ground effect the low horizontal tail did not appear to be in an adverse flow field as had been expected and showed no erratic changes in effectiveness; however, in ground effect a large nose-down moment was experienced by the model. In general, the lateral aerodynamic data indicate that the configuration is directionally stable and possesses positive dihedral effect throughout the transition, and the data show no signs of erratic flow at the vertical tails.

Grunwald, Kalman J.↗

Full-Scale Wind-Tunnel Investigation of the VZ-5 Four-Propeller Deflected-Slipstream VTOL Airplane

The investigation was conducted to determine the static stability and control characteristics of the VZ-5 VTOL air-plane over the speed range from hovering to forward flight. Force and moment data were taken over a range of angles of attack of 0 to 15 deg and a range of sideslip of +/-10 deg for flap deflections from 0 to 77 deg. The longitudinal stability and trim characteristics were found to be quite unacceptable and it did not seem that they could be corrected with any reasonable modifications to the airplane.

Fink, Marvin P.↗

Low-Speed Measurements of Static and Oscillatory Lateral Stability Derivatives of a 1/5-scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

An investigation has been made in the Langley free-flight tunnel to determine the low-speed static lateral stability characteristics and the rolling, yawing, and sideslipping dynamic stability derivatives of a 1/5-scale model of a jet-powered vertical-attitude VTOL research airplane. The results of this investigation are presented herein without analysis.

Shanks, Robert E.↗

Hovering and Transition Flight Tests of a 1/5-Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/5-scale flying model of a jet-powered vertical-attitude VTOL research airplane in hovering and transition flight. The model was powered with either a hydrogen peroxide rocket motor or a compressed-air jet exhausting through an ejector tube to simulate the turbojet engine of the airplane. The gyroscopic effects of the engine were simulated by a flywheel driven by compressed-air jets. In hovering flight the model was controlled by jet-reaction controls which consisted of a swiveling nozzle on the main jet and a movable nozzle on each wing tip; and in forward flight the model was controlled by elevons and a rudder. If the gyroscopic effects of the jet engine were not represented, the model could be flown satisfactorily in hovering flight without any automatic stabilization devices. When the gyroscopic effects of the jet engine were represented, however, the model could not be controlled without the aid of artificial stabilizing devices because of the gyroscopic coupling of the yawing and pitching motions. The use of pitch and yaw dampers made these motions completely stable and the model could then be controlled very easily. In the transition flight tests, which were performed only with the automatic pitch and yaw dampers operating, it was found that the transition was very easy to perform either with or without the engine gyroscopic effects simulated, although the model had a tendency to fly in a rolled and sideslipped attitude at angles of attack between approximately 25 deg and 45 deg because of static directional instability in this range.

Smith, Charles C., Jr.↗

Low-Speed Measurements of Static and Oscillatory Lateral Stability Derivatives of a 1/5 Scale Model of a Jet-Powered Vertical-Attitude VTOL Research Airplane

Force tests of the static and dynamic lateral stability characteristics of a VTOL airplane having a triangular wing mounted high on the fuselage with a triangular vertical tail on top of the wing and no horizontal tail have been made in the Langley free-flight tunnel. The static lateral stability parameters and the rolling, yawing, and sideslipping dynamic stability derivatives are presented without analysis.

Shanks, Robert E.↗

Operational Experiences with the X-14A Deflected-Jet VTOL Aircraft

During 5 1/2 years of flight research with a deflected-jet VTOL aircraft a 2 number of operational problems were experienced and investigated. These experiences can be grouped into two general categories: (1) the effects of the jet engine and its operation and (2) the restrictions imposed upon the pilot's operation due to reduced visual reference. This report is an examination of these problems and., in some cases, presents possible solutions to these problems.

Rolls, L. Stewart↗

A Preliminary Study of V/STOL Transport Aircraft and Bibliography of NASA Research in the VTOL-STOL Field

This group of papers was prepared by the staff of the Langley Research Center to assist in planning for future commercial air-transport facilities in the New York metropolitan area. Areas of particular interest were predictions regarding the types of V/STOL aircraft that are likely to be developed for various commercial transport applications, estimates of the performance and probable operating procedures for such aircraft, and the approximate dates these aircraft could be available for use. Although the NASA has made no comprehensive studies of this type, the extensive research program in the VTOL-STOL field during the last 10 years appeared to provide a source for some of the desired information . The five papers included herein were therefore prepared to summarize pertinent available material in a form suitable for the intended use. In several instances, new studies and analysis were required to provide the necessary information, but because of a time deadline, many of the significant points received only a cursory examination. For example, much of the quantitative data used in the papers for making generalized comparisons was obtained by approximate methods and is not considered appropriate for use in applications where precise estimates are required. It should be recognized, then, that the treatment of the V/STOL transport provided by this group of papers is necessarily of a preliminary nature.

Source record↗

Nomographic Solution of the Momentum Equation for VTOL-STOL Aircraft

VTOL-STOL aircraft are characterized in general by the fact that in some portion of their flight envelope the wake is sharply inclined to the free stream. Under such conditions, the usual small-angle assumptions used in determining the induced velocities, and consequently, the power required, are no longer valid. Indeed, the use of small-angle assumptions leads to such anomalous results as infinite induced velocities and required power in the extreme case of hovering. The aforementioned difficulties may be avoided by a more complete examination of the horizontal and vertical momentum imparted to the air by the aircraft at low speeds. The resulting equation is a quartic in the induced velocity, and, as such, is difficult to apply. On the other hand, this quartic can be solved in its most general terms and the resulting solution then can be derived and presented in the form of a chart, or nomograph, from which the required induced velocities my be read directly. This paper presents such a chart.

Heyson, Harry H.↗

An Investigation of the Effect of Downwash from a VTOL Aircraft and a Helicopter in the Ground Environment

Dynamic-pressure measurement, in ground effect, have been obtained about a single-rotor helicopter and a dual-propeller VTOL (Vertical Take-Off and Landing) aircraft. The results indicate that the slipstream dynamic pressure along the ground, some distance from the center of rotation, is not a function of disk loading but merely a function of the gross weight or thrust of the aircraft. Furthermore, for a given gross weight the thickness of this outward flowing sheet of air is less for a small-diameter propeller (higher disk loading propeller). The variation of the dynamic-pressure flow field for single and dual propellers or rotors is significantly different in the plane of symmetry between the two rotors than in a direction normal to this plane. The interaction of the two flows produces a region of upflow in this plane where the fuselage is located, and the decay of the maximum dynamic pressure with distance ahead of the fuselage is slower.

O'Bryan, Thomas C.↗

Aerodynamic Characteristics of Propeller-Driven VTOL Aircraft

This paper discusses the two major configurations that are usually considered for achieving VTOL while keeping the fuselage essentially horizontal - that is, the tilt-wing and the deflected-slipstream configurations. Because of the high turning losses incurred by deflected-slipstream configurations in hovering and because of the wing-stalling problem of the pure tilt-wing configurations during the transition, it appears that a combination of the two principles should be used. This tilt-wing and flap configuration should make use of a programmed extensible-chord slotted flap together with a leading-edge high-lift device in order to avoid the performance and handling qualities problems associated with wing stalling during the transition while keeping the wing area as low as possible for efficiency in cruising flight.

Kirby, Robert H.↗