Wind tunnel tests of a wing-installed model VTOL lift fan with coaxial drive turbine
Wing installed VTOL coaxial drive lift fan model in wind tunnel test, investigating performance in crosswind environment
Diedrich, J. H.↗
SEARCH · Search NASA
Results for “WIND TUNNEL TESTS - CORRECTIONS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A low speed wind tunnel test of the 0.050 scale NASA-JSC shuttle orbiter 089B to determine the longitudinal and lateral directional effects of control surface modifications
Wind tunnel tests to determine the longitudinal and lateral-directional effects of control surface modifications on the space shuttle orbiter aerodynamic characteristics are discussed. A total of 103 data runs were made which consisted of pitch runs through a range of zero to 28 degrees at a zero yaw angle and yaw runs from minus 6 to plus 6 degrees at various fixed pitch angles. At each data point, data from an internal strain gage balance was sampled with the digital data system. Also recorded were the model angles of pitch and yaw and the test section static pressure. Results are presented in the form of tabulated aerodynamic coefficient data about the model reference center.
Oldenbuttel, R. H.↗
NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration
NASAs Environmentally Responsible Aviation (ERA) Project explores enabling technologies to reduce aviations impact on the environment. One research challenge area for the project has been to study advanced airframe and engine integration concepts to reduce community noise and fuel burn. In order to achieve this, complex wind tunnel experiments at both the NASA Langley Research Centers (LaRC) 14x22 and the Ames Research Centers 40x80 low-speed wind tunnel facilities were conducted on a Boeing Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion airframe interference effects including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on the vehicles aerodynamics. This paper will provide a high level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as some simulation guideline development based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.
Computational Fluid Dynamics↗
Wind Tunnel Testing of Powered Lift, All-Wing STOL Model
Short take-off and landing (STOL) systems can offer significant capabilities to warfighters and, for civil operators thriving on maximizing efficiencies they can improve airspace use while containing noise within airport environments. In order to provide data for next generation systems, a wind tunnel test of an all-wing cruise efficient, short take-off and landing (CE STOL) configuration was conducted in the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) 14- by 22-foot Subsonic Wind Tunnel. The test s purpose was to mature the aerodynamic aspects of an integrated powered lift system within an advanced mobility configuration capable of CE STOL. The full-span model made use of steady flap blowing and a lifting centerbody to achieve high lift coefficients. The test occurred during April through June of 2007 and included objectives for advancing the state-of-the-art of powered lift testing through gathering force and moment data, on-body pressure data, and off-body flow field measurements during automatically controlled blowing conditions. Data were obtained for variations in model configuration, angles of attack and sideslip, blowing coefficient, and height above ground. The database produced by this effort is being used to advance design techniques and computational tools for developing systems with integrated powered lift technologies.
Collins, Scott W.↗
Analytical Investigation of the Reentry Behavior of the ''flying Wind Tunnel'' Test Vehicle, with Some Effects of Threshold and Torque Level of a Roll-rate Control System
Analytical investigation of reentry behavior of flying wind tunnel test vehicle with some effects of threshold and torque level of roll-rate control system
CONTROL SYSTEM↗
Wind tunnel tests of the GA(W)-2 airfoil with 20% aileron, 25% slotted flap, 30% Fowler flap and 10% slot-lip spoiler
Two dimensional wind tunnel tests were conducted for the GA(W)-2 airfoil section with: 20% aileron, 25% slotted flap; 30% Fowler flap, and 10% slot-lip spoiler. All tests were conducted at a Reynolds number of 2,200,000 and a Mach Number of 0.13. In addition to force measurements, tuft studies were conducted for the slotted and Fowler flap configurations. Aileron and spoiler hinge moments were obtained by integration of surface pressure measurements. Tests results show that a value of 3.82 was obtained with 30% Fowler flap. Aileron control effectiveness and hinge moments were similar to other airfoils. The slot-lip spoiler provided powerful, positive roll control at all flap settings.
Wentz, W. H., Jr.↗
High-Speed Wind-Tunnel Tests of a 0.3-Scale Model of the P-47D Airplane
Presented in this report are the results of high-speed wind-tunnel tests of a 0.3-scale model of the P-47D airplane. Included are the aerodynamic characteristics of the model, pressure distributions on the wing and horizontal tail, elevator hinge moments, and tuft photographs showing the flow over the wing and horizontal tail. The results indicate that, at level-flight lift coefficients, the P-47D airplane will not exhibit a diving tendency below a Mach number of 0.78 at an altitude of 20,000 feet or below a Mach number of 0.72 at an altitude of 40,000 feet. The Mach number at which the lift, drag, and pitching-moment coefficients diverged rapidly from the low speed values is about C.15 higher than the critical Mach number. This is an unusually large margin.
William T Hamilton↗
Wind-Tunnel Tests of the 1/25-Scale Powered Model of the Martin JRM-1 Airplane. IV - Tests with Ground Board and with Modified Wing and Hull - TED No. NACA 232: Tests with Ground Board and with Modified Wing and Hull, TED No. NACA 232 - Part 4
Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.
Lockwood, Vernard E.↗
Large-scale wind-tunnel tests of an airplane model with two propellers and rotating cylinder flaps
Wind tunnel stability tests of twin engined turboprop aircraft with rotating cylinder flaps
Gamse, B.↗
Unified Instrumentation: Examining the Simultaneous Application of Advanced Measurement Techniques for Increased Wind Tunnel Testing Capability
A Unified Instrumentation Test examining the combined application of Pressure Sensitive Paint, Projection Moire Interferometry, Digital Particle Image Velocimetry, Doppler Global Velocimetry, and Acoustic Microphone Array has been conducted at the NASA Langley Research Center. The fundamental purposes of conducting the test were to: (a) identify and solve compatibility issues among the techniques that would inhibit their simultaneous application in a wind tunnel, and (b) demonstrate that simultaneous use of advanced instrumentation techniques is feasible for increasing tunnel efficiency and identifying control surface actuation / aerodynamic reaction phenomena. This paper provides summary descriptions of each measurement technique used during the Unified Instrumentation Test, their implementation for testing in a unified fashion, and example results identifying areas of instrument compatibility and incompatibility. Conclusions are drawn regarding the conditions under which the measurement techniques can be operated simultaneously on a non-interference basis. Finally, areas requiring improvement for successfully applying unified instrumentation in future wind tunnel tests are addressed.
Fleming, Gary A.↗
Full-scale wind tunnel tests of a low-wing, single-engine, light plane with positive and negative propeller thrust and up and down flap deflection
Full scale wind tunnel tests of low wing, single engine, light aircraft with positive and negative propeller thrust and up and down flap deflection - graphs
Morris, J. J.↗
Performance characteristics from wind-tunnel tests of a low-Reynolds-number airfoil
Wind tunnel lift and pitching-moment data have been obtained from pressure measurements, and drag data from wake surveys, for an Eppler 387 low Reynolds number airfoil over the Re range of 60,000 to 460,000; oil flow visualizations were also used to determine laminar separation and turbulent reattachment locations. Airfoil performance is found to be dominated by laminar separation bubbles below Re 200,000, and two flow regimes, namely laminar separations with and without turbulent reattachment, were observed at the same angle-of-attack for an Re of 60,000.
Mcghee, Robert J.↗
Wind tunnel tests of rotor blade sections with replications of ice formations accreted in hover
Full scale reproductions of ice accretions molded during the documentation of a hover test program were fabricated by means of epoxy castings and used for a wind tunnel test program. Surface static pressure distributions were recorded and used to evaluate lift and pitching moment increments while drag was determined by wake surveys. Through the range of the tests, corresponding to those conditions encountered in hover and in flat pitch, integration of the pressure distributions showed negligible changes in lift and in pitching moment, but the drag was significantly increased.
Lee, J. D.↗
Wind tunnel test of the 0.019 scale space shuttle integrated vehicle (model 14-OTS) in the CALSPAN 8-foot transonic wind tunnel (IA36), volume 2
A test is presented which was performed to determine the effect of cold jet gas plumes generated from main propulsion system and solid rocket motor nozzles on: (1) six-component force and moment data, (2) wing static pressures, (3) wing hinge moment, (4) elevon hinge moment, (5) rudder hinge moment, and (6) orbiter MPS nozzle pressure loads. The effects of rudder deflection, nozzle gimbal angle, and plume size were also obtained.
Hardin, R. B.↗
An analytical study and wind tunnel tests of an aeromechanical gust-alleviation system for a light airplane
The results of an analytical study of a system using stability derivatives determined in static wind tunnel tests of a 1/6 scale model of a popular, high wing, light airplane equipped with the gust alleviation system are reported. The longitudinal short period mode dynamics of the system are analyzed, and include the following: (1) root loci, (2) airplane frequency responses to vertical gusts, (3) power spectra of the airplane responses in a gust spectrum, (4) time history responses to vertical gusts, and (5) handling characteristics. The system reduces the airplane's normal acceleration response to vertical gusts while simultaneously increasing the pitching response and reducing the damping of the longitudinal short period mode. The normal acceleration response can be minimized by using the proper amount of static alleviation and a fast response system with a moderate amount of damping. The addition of a flap elevator interconnect or a pitch damper system further increases the alleviation while moderating the simultaneous increase in pitching response. The system provides direct lift control and may reduce the stick fixed longitudinal static stability.
Stewart, E. C.↗
Aeroservoelastic Control Law Development for the Integrated Adaptive Wing Technology Maturation Wind-Tunnel Test
In this paper, a linear quadratic Gaussian (LQG) regulator was applied to a computational aeroservoelastic (ASE) model of the Integrated Adaptive Wing Technology Maturation (IAWTM) wind-tunnel model to demonstrate its effectiveness for active flutter suppression. The aerodynamics within this computational ASE model were solved using unsteady Reynolds-averaged Navier-Stokes (RANS) equations; the structural dynamics of the model were solved using modal analysis. This RANS-based ASE model was used as the plant for the LQG regulator. The Kalman filter and controller used within the LQG regulator were derived from a reduced-order model (ROM) of the RANS-based ASE model. This ROM-based ASE model was generated using system identification techniques. It was shown that the Kalman filter adequately predicted important states of the plant, and that LQG regulator successfully stabilized an aeroelastically unstable plant without exceeding reasonable control surface limitations. All of this was demonstrated using simulation data, and the methods presented here appear feasible for use in the upcoming IAWTM wind-tunnel tests.
Josiah M. Waite↗
Inlet Unstart Propulsion Integration Wind Tunnel Test Program Completed for High-Speed Civil Transport
One of the propulsion system concepts to be considered for the High-Speed Civil Transport (HSCT) is an underwing, dual-propulsion, pod-per-wing installation. Adverse transient phenomena such as engine compressor stall and inlet unstart could severely degrade the performance of one of these propulsion pods. The subsequent loss of thrust and increased drag could cause aircraft stability and control problems that could lead to a catastrophic accident if countermeasures are not in place to anticipate and control these detrimental transient events. Aircraft system engineers must understand what happens during an engine compressor stall and inlet unstart so that they can design effective control systems to avoid and/or alleviate the effects of a propulsion pod engine compressor stall and inlet unstart. The objective of the Inlet Unstart Propulsion Airframe Integration test program was to assess the underwing flow field of a High-Speed Civil Transport propulsion system during an engine compressor stall and subsequent inlet unstart. Experimental research testing was conducted in the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center at Lewis Field. The representative propulsion pod consisted of a two-dimensional, bifurcated inlet mated to a live turbojet engine. The propulsion pod was mounted below a large flat plate that acted as a wing simulator. Because of the plate s long length (nominally 10-ft wide by 18-ft long), realistic boundary layers could form at the inlet cowl plane. Transient instrumentation was used to document the aerodynamic flow-field conditions during an unstart sequence. Acquiring these data was a significant technical challenge because a typical unstart sequence disrupts the local flow field for about only 50 msec. Flow surface information was acquired via static pressure taps installed in the wing simulator, and intrusive pressure probes were used to acquire flow-field information. These data were extensively analyzed to determine the impact of the unstart transient on the surrounding flow field. This wind tunnel test program was a success, and for the first time, researchers acquired flow-field aerodynamic data during a supersonic propulsion system engine compressor stall and inlet unstart sequence. In addition to obtaining flow-field pressure data, Glenn researchers determined other properties such as the transient flow angle and Mach number. Data are still being reduced, and a comprehensive final report will be released during calendar year 2000.
Porro, A. Robert↗
Computational Support of 9x7 Wind Tunnel Test of Sonic Boom Models with Plumes
NASA and its industry partners are performing studies of supersonic aircraft concepts with low sonic boom pressure signatures. The interaction of the nozzle jet flow with the aircrafts' aft components is typically where the greatest uncertainly in the pressure signature is observed with high-fidelity numerical simulations. An extensive wind tunnel test was conducted in February 2016 in the NASA Ames 9- by 7- Foot Supersonic Wind Tunnel to help address the nozzle jet effects on sonic boom. Five test models with a variety of shock generators of differing waveforms and strengths were tested with a convergent-divergent nozzle for a wide range of nozzle pressure ratios. The LAVA unstructured flow solver was used to generate first CFD comparisons with the new experimental database using best practice meshing and analysis techniques for sonic boom vehicle design for all five different configurations. LAVA was also used to redesign the internal flow path of the nozzle and to better understand the flow field in the test section, both of which significantly improved the quality of the test data.
9x7 Wind Tunnel↗