Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Prediction of vortex-induced loads on wind-tunnel turning vanes

Models tested in the National Full-Scale Aerodynamic Complex at NASA Ames Research Center can generate strong wake vortices which in turn can induce large increases in the local loads on the turning vanes located downstream from the two test sections. A 3-D panel method which models wake roll up (VSAERO) was used to estimate the magnitude of these loads. In the simulation a rectangular wing at angle of attack sheds a wake which is allowed to roll up and interact with a smaller chord, high-aspect ratio wing which represents a single vane. Results agree well with experimental data and are consistent with previously reported results. A method is given for correcting the panel code results for the effects of vane set solidity and of the vortex passage through a diffuser before it interacts with the vane set. Estimates of the induced vortex loads on the vane sets downstream from the 40- by 80- and 80- by 120-foot test sections indicate that the induced local loads on a van can, in some cases, be more than 50% of the steady-state turning loads of an individual vane.

Ross, J. C.↗
NASA NTRS1985

Generation of three-dimensional body-fitted coordinates using hyperbolic partial differential equations

An efficient numerical mesh generation scheme capable of creating orthogonal or nearly orthogonal grids about moderately complex three dimensional configurations is described. The mesh is obtained by marching outward from a user specified grid on the body surface. Using spherical grid topology, grids have been generated about full span rectangular wings and a simplified space shuttle orbiter.

Steger, J. L.↗
NASA NTRS1985

Program LRCDM2: Improved aerodynamic prediction program for supersonic canard-tail missiles with axisymmetric bodies

Program LRCDM2 was developed for supersonic missiles with axisymmetric bodies and up to two finned sections. Predicted are pressure distributions and loads acting on a complete configuration including effects of body separated flow vorticity and fin-edge vortices. The computer program is based on supersonic panelling and line singularity methods coupled with vortex tracking theory. Effects of afterbody shed vorticity on the afterbody and tail-fin pressure distributions can be optionally treated by companion program BDYSHD. Preliminary versions of combined shock expansion/linear theory and Newtonian/linear theory have been implemented as optional pressure calculation methods to extend the Mach number and angle-of-attack ranges of applicability into the nonlinear supersonic flow regime. Comparisons between program results and experimental data are given for a triform tail-finned configuration and for a canard controlled configuration with a long afterbody for Mach numbers up to 2.5. Initial tests of the nonlinear/linear theory approaches show good agreement for pressures acting on a rectangular wing and a delta wing with attached shocks for Mach numbers up to 4.6 and angles of attack up to 20 degrees.

Dillenius, Marnix F. E.↗
NASA NTRS1990

The FX/90: A proposal in response to a low Reynolds Number station keeping mission

The FX/90 is a remotely piloted vehicle designed to fly at Reynolds numbers below 2 x 10 to the 5th power. Several applications exist for this type of flight, such as low altitude flight of very small aircraft. The design presented here allows investigation into the unique problems involved in low Reynolds number flight, which will, in turn, further understanding of this flight regime. The aircraft will operate in a steady flight environment, free from significant atmospheric turbulence and weather effects. The F-90 has a 39 in. fuselage which is constructed of balsa and plywood. The landing gear for the aircraft is a detachable carriage on which the aircraft rests. The aerodynamic planform is a rectangular wing (no taper or sweep) with a chord of 9 in., a wingspan of 72 in., and is constructed entirely out of styrofoam. The propulsion system is a puller configuration mounted on the front of the fuselage. It consists of an Astro 05 engine and a 10-6 two bladed propeller. Control of the aircraft is accomplished through the use of two movable control surfaces: elevators for pitch control, and a rudder for yaw control. The aircraft is soundly constructed, highly maneuverable, and adequately powered. Furthermore, the investigation into alternative technologies, most notably the styrofoam wing and the detachable landing gear, holds promise to improve the performance of the aircraft.

Wirthman, David↗
NASA NTRS1991

A methodology for using nonlinear aerodynamics in aeroservoelastic analysis and design

A methodology is presented for using the Volterra-Wiener theory of nonlinear systems in aeroservoelastic (ASE) analyses and design. The theory is applied to the development of nonlinear aerodynamic response models that can be defined in state-space form and are, therefore, appropriate for use in modern control theory. The theory relies on the identification of nonlinear kernels that can be used to predict the response of a nonlinear system due to an arbitrary input. A numerical kernel identification technique, based on unit impulse responses, is presented and applied to a simple bilinear, single-input single-output (SISO) system. The linear kernel (unit impulse response) and the nonlinear second-order kernel of the system are numerically-identified and compared with the exact, analytically-defined and linear and second-order kernels. This kernel identification technique is then applied to the CAP-TSD (Computational Aeroelasticity Program-Transonic Small Disturbance) code for identification of the linear and second-order kernels of a NACA64A010 rectangular wing undergoing pitch at M = 0.5, M = 8.5 (transonic), and M = 0.93 (transonic). Results presented demonstrate the feasibility of this approach for use with nonlinear, unsteady aerodynamic responses.

Silva, Walter A.↗
NASA NTRS1991

A methodology for using nonlinear aerodynamics in aeroservoelastic analysis and design

A methodology is presented for using the Volterra-Wiener theory of nonlinear systems in aeroservoelastic (ASE) analyses and design. The theory is applied to the development of nonlinear aerodynamic response models that can be defined in state-space form and are, therefore, appropriate for use in modern control theory. The theory relies on the identification of nonlinear kernels that can be used to predict the response of a nonlinear system due to an arbitrary input. A numerical kernel identification technique, based on unit impulse responses, is presented and applied to a simple bilinear, single-input-single-output system. The linear kernel (unit impulse response) and the nonlinear second-order kernel of the system are numerically-identified and compared with the exact, analytically-defined linear and second-order kernels. This kernel identification technique is then applied to the CAP-TSD code for identification of the linear and second-order kernels of a NACA64A010 rectangular wing undergoing pitch at M = 0.5, M = 0.85 (transonic), and M = 0.93 (transonic). Results presented demonstrate the feasibility of this approach for use with nonlinear, unsteady aerodynamic responses.

Silva, Walter A.↗
NASA NTRS1991

Sonic boom predictions for three generic models using a solution-adaptive full-potential code

The TranAir full-potential code, which utilizes a solution-adaptive, unstructured Cartesian grid, was used to compute near-field pressure signatures of three generic supersonic configurations: a cone-cylinder, a low aspect ratio rectangular wing, and a delta-wing/body. TranAir pressure signatures are extrapolated to near- and mid-field distances using a quasi-linear extrapolation technique. Results are compared with existing wind tunnel data and, where possible, with extrapolated experimental data and quasi-linear Whitham-method results. In general, the extrapolated TranAir data is in good agreement with experimental and Whitham-method pressure signatures, but peak pressures are slightly under-predicted. It is thought that computed data obtained too near to the model was the main reason for the discrepancies. Flow-field grid structure was also found to be important in obtaining accurate offbody data.

Madson, Michael D.↗
NASA NTRS1991

Technical activities of the configuration aeroelasticity branch

A number of recent technical activities of the Configuration Aeroelasticity Branch of the NASA Langley Research Center are discussed in detail. The information on the research branch is compiled in twelve separate papers. The first of these topics is a summary of the purpose of the branch, including a full description of the branch and its associated projects and program efforts. The next ten papers cover specific projects and are as follows: Experimental transonic flutter characteristics of supersonic cruise configurations; Aeroelastic effects of spoiler surfaces mounted on a low aspect ratio rectangular wing; Planform curvature effects on flutter of 56 degree swept wing determined in Transonic Dynamics Tunnel (TDT); An introduction to rotorcraft testing in TDT; Rotorcraft vibration reduction research at the TDT; A preliminary study to determine the effects of tip geometry on the flutter of aft swept wings; Aeroelastic models program; NACA 0012 pressure model and test plan; Investigation of the use of extension twist coupling in composite rotor blades; and Improved finite element methods for rotorcraft structures. The final paper describes the primary facility operation by the branch, the Langley TDT.

Cole, Stanley R.↗
NASA NTRS1991

Experimental study of a vortex subjected to imposed strain

An experimental project was undertaken to investigate the character of vortex breakdown with particular regard to the waveguide theories of vortex breakdown. A rectangular wing based on the NACA 0012 airfoil was used to produce a trailing vortex which convected downstream without undergoing breakdown. Dye marked the vortex location. A disturbance was then introduced onto the vortex using a small moving wire to 'cut' the vortex. The development of upstream and downstream propagating disturbance waves was observed and the propagation velocities measured. The downstream traveling wave produced a structure similar in appearance to a vortex breakdown. The upstream wave produced a moving, swirling, turbulent region that was not a vortex breakdown. The waves moving in either direction have the same swirl velocity profiles but quite different axial velocity profiles. The upstream disturbance (turbulence) moved into a flow with an axial velocity profile that had a wake-like defect in the core region. The downstream moving vortex breakdown moved into a flow with a jet-like overshoot in the core region. The fact that no breakdown was observed for the wake-like defect and breakdown was observed for the jet-like overshoot is not consistent with computational fluid dynamics (CFD) calculations. Although there are not a lot of examples, CFD results show breakdown for both types of profiles. The longitudinal and swirl velocity profiles were documented by Laser Doppler Velocimeter (LDV) measurement. Wave velocities, swirl angles, and swirl parameters are reported.

Panton, Ronald L.↗
NASA NTRS1992

New time-domain technique for flutter boundary identification

A new methodology for flutter boundary identification in the time domain is presented. This technique is based on a single-input single-output deterministic ARMA model and an on-line parameter estimation procedure. It is capable of simultaneous identification of the aeroelastic modal parameters as well as the static offset term which represents the static deformation or state of the aeroelastic system. The capabilities of the method are illustrated by applying it to several examples, such as: damped free oscillations, a two degree of freedom NACA 64A010 airfoil in transonic flight, and a cantilevered rectangular wing in subsonic flow. Numerical implementations of the new methodology developed in this study demonstrates that it is a cost effective time-domain technique for flutter boundary identification.

Pak, Chan-Gi↗
NASA NTRS1991

Electrical design and analysis of the TOPEX/Poseidon solar array

TOPEX/Poseidon, a scientific satellite to be launched into low earth orbit, will map the surface topography of the earth's oceans. The satellite derives its primary electrical power from a deployable, sun tracking, rigid, single wing, rectangular solar array with overall dimensions of approximately 26 by 11 ft. The requirements which affect the electrical performance of the solar array and the method by which each requirement is satisfied are addressed. The worst-case power calculations used to size the solar array and to verify power capability are discussed. Also included is a detailed description of the solar array configuration and a summary of the qualification and acceptance testing.

Roufberg, Lew↗
NASA NTRS1992

Flow visualizations of perpendicular blade vortex interactions

Helium bubble flow visualizations have been performed to study perpendicular interaction of a turbulent trailing vortex and a rectangular wing in the Virginia Tech Stability Tunnel. Many combinations of vortex strength, vortex-blade separation (Z(sub s)) and blade angle of attack were studied. Photographs of representative cases are presented. A range of phenomena were observed. For Z(sub s) greater than a few percent chord the vortex is deflected as it passes the blade under the influence of the local streamline curvature and its image in the blade. Initially the interaction appears to have no influence on the core. Downstream, however, the vortex core begins to diffuse and grow, presumably as a consequence of its interaction with the blade wake. The magnitude of these effects increases with reduction in Z(sub s). For Z(sub s) near zero the form of the interaction changes and becomes dependent on the vortex strength. For lower strengths the vortex appears to split into two filaments on the leading edge of the blade, one passing on the pressure and one passing on the suction side. At higher strengths the vortex bursts in the vicinity of the leading edge. In either case the core of its remnants then rapidly diffuse with distance downstream. Increase in Reynolds number did not qualitatively affect the flow apart from decreasing the amplitude of the small low-frequency wandering motions of the vortex. Changes in wing tip geometry and boundary layer trip had very little effect.

Rife, Michael C.↗
NASA NTRS1993

Extension of a nonlinear systems theory to general-frequency unsteady transonic aerodynamic responses

A methodology for modeling nonlinear unsteady aerodynamic responses, for subsequent use in aeroservoelastic analysis and design, using the Volterra-Wiener theory of nonlinear systems is presented. The methodology is extended to predict nonlinear unsteady aerodynamic responses of arbitrary frequency. The Volterra-Wiener theory uses multidimensional convolution integrals to predict the response of nonlinear systems to arbitrary inputs. The CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code is used to generate linear and nonlinear unit impulse responses that correspond to each of the integrals for a rectangular wing with a NACA 0012 section with pitch and plunge degrees of freedom. The computed kernels then are used to predict linear and nonlinear unsteady aerodynamic responses via convolution and compared to responses obtained using the CAP-TSD code directly. The results indicate that the approach can be used to predict linear unsteady aerodynamic responses exactly for any input amplitude or frequency at a significant cost savings. Convolution of the nonlinear terms results in nonlinear unsteady aerodynamic responses that compare reasonably well with those computed using the CAP-TSD code directly but at significant computational cost savings.

Silva, Walter A.↗
NASA NTRS1993

Turbulent structure of a wingtip vortex in the near field

The turbulent rollup of a vortex generated by a rectangular wing has been investigated. Extensive mean and turbulence measurements of the flowfield on a wingtip and in the near field have been completed. Velocity fluctuation measurements show that the near-field core is not laminar. A large axial velocity excess was found to exist in the core of the vortex. A momentum balance in the near-field of the wingtip showed that the magnitude of the core Reynolds-stress gradient terms are the same order as the largest terms in the governing equations. Navier-Stokes computations of the identical configuration, including wind tunnel walls and using measured inflow and outflow boundary conditions, reproduced many of the features of the experiment. Inherent limitations of the Baldwin-Barth turbulence model combined with limited grid resolution caused the computed vortex core to be more diffuse than desired. The momentum balance also demonstrated that the level of numerically generated false diffusion in the vortex core is relatively high.

Zilliac, Gregory G.↗
NASA NTRS1938

Wind-tunnel of three lateral-control devices in combination with a full-span slotted flap on an NACA 23012 airfoil

A large-chord NACA 23012 airfoil was tested. The airfoil extended completely across the test section, and two-dimensional flow was approximated. The model was fitted with a full-span slotted flap having a chord 25.66 percent of the airfoil chord. The ailerons investigated extended over the entire span and each had a chord 10 percent of the airfoil chord. The types of ailerons tested were: retractable ailerons, slot-lip ailerons using the lip of the slot for ailerons, and plain ailerons on the trailing edge of the slotted flap. The data are presented in the form of curves of section lift, drag, and pitching-moment coefficients for the airfoil with flap deflected but with ailerons neutral, and of rolling-moment, yawing-moment, and hinge-moment coefficients calculated for a rectangular wing of aspect ratio 6 with a semi-span aileron and a full-span flap. For the ailerons investigated the data indicate that, from considerations of rolling and yawing moments produced and of stick forces desired, the retractable aileron is the most satisfactory means of lateral control for use with a full-span slotted flap.

Wenzinger, Carl J↗