Search NASA⌕ Search

SEARCH · Search NASA

Results for “Welding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Fatigue Performance of High-Strength Pipeline Steels and Their Welds in Hydrogen Gas Service

Objectives of the project include: Enable the use of high strength steel hydrogen pipelines, as significant cost savings can result by implementing high strength steels as compared to lower strength pipes. Demonstrate that girth welds in high-strength steel pipe exhibit fatigue performance similar to lower-strength steels in high-pressure hydrogen gas. Identify pathways for developing high-strength pipeline steels by establishing the relationship between microstructure constituents and hydrogen-accelerated fatigue crack growth (HA-FCG)

08 HYDROGEN↗
DOE OSTI2021

Low Cost HIP Fabrication of Advanced Power Cycle Components and PM/Wrought Inconel 740H Weld Development (Final Technical Report)

The objective of this Phase 1 project is to demonstrate the feasibility of structures and components for advanced fossil energy power cycle by fusion welding powder metallurgy (PM) based near net shape (NNS) hot isostatic pressing (HIP) Nickel superalloy Inconel 740H (IN740H) components to wrought IN740H components. The outcome of the project includes a prototype pipe elbow demonstration of the NNS HIP process using IN740H powder, an initial assessment of IN740H PM/wrought weldability, and a manufacturing and capital cost analysis of IN740H NNS HIP components for advanced ultra-super critical steam (AUSC) power plants. The anticipated value proposition of NNS HIP manufacturing is ~50% cost reduction of large complex components in AUSC or super-critical carbon dioxide (sCO2) power cycles. This document is a final technical report for the project, covering efforts conducted from October 2019 to June 2021.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Similar Exposure Group [Stick Welding without LEV - Manganese - RiskLevel 4]

This memorandum is presented to summarize quantitative worker exposure data collected while performing shielded metal arc welding (“SMAW” or “stick”) without local exhaust ventilation (LEV) and to validate if the appropriate risk level has been assigned to this task using Bayesian Decision Analysis (BDA). The purpose of this exposure assessment is to determine if it can be stated with at least 75% certainty that the true exposure profile (i.e., 95 th percentile) of the SEG is at or below the risk level currently assigned to this SEG.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2022

3013 Inner Container Closure Weld Region (ICCWR) Characterization by Wide Area 3D Measurement System (WAMS) Analysis (FY21 Progress Report)

As part of the 3013 Surveillance Program, through-wall penetration from stress corrosion cracking (SCC) of the 3013 inner containers has been identified as the most credible condition for failure withing the 50- years lifetime. Chlorides contained in Pu-bearing material, together with intra-canister humidity levels, metallurgical conditions, and internal stresses have been found to produce corrosion in the Inner Container Closure Weld Region (ICCWR) of the 3013 canister system. A Laser Confocal Microscope (LCM) is used as part of the 3013 Surveillance Program protocol to identify the prevalence of corrosion and corrosionrelated cracking in the ICCWR2. With the LCM, a close visual examination is made of the ICCWR surface along with measurements of corrosion-related features. LCM inspections produce immense amounts of image data that is time intensive to analyze. There is also a 9-year backlog of images, with approximately 49 canisters that must be evaluated. To expedite data analysis and reduce the amount of generated data, a Wide Area 3D Measurement System (WAMS) microscope has been added to the examination protocol. Although WAMS is a lower resolution microscope, small features of interest can be still identified. The advantage of collecting data for the full circumference using the WAMS is that it can take about 1/16 of the time needed with the LCM. Both systems offer capabilities that combined can be utilized to expedite the examination of the ICCWR. The WAMS is an efficient system for screening and identification of corrosion features while the LCM can be utilized to obtain higher resolution images areas identified by the WAMS. This report explains and justifies the data collection methods used with the WAMS. It includes a summary of the data generated by WAMS in FY21. The goals set for data collection in FY21 were met. A total of twenty-two DE’s were imaged, and analysis was carried out on eleven samples. The analyzed samples showed large numbers of potential cracks and pits distributed throughout the surfaces. Lastly, to explain the advantages of the WAMS, its capabilities were compared to those of a simpler microscope. Micrographs of the samples imaged in FY21 and those analyzed are included in the appendices.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Simulation of Multipaction in LB650 Cavity with Weld Profile

This study aims to simulate multipaction in LB650 cavity with weld profile, a first step to replicating an actual cavity, whereas past studies have ignored the same. We attempt to align the simulation data with the experimental data and report the subsequent findings.

Ninan, Z.↗
DOE OSTI2023

Arc Weld Robotic Arm & Enclosure Seismic Anchorage in B226

The Arc Weld Robotic Arm & Enclosure is adequately anchored by the details shown on sheets SKS-01 through SKS-03. Two different Hilti anchors have been provided to allow for installation flexibility. Existing documentation shows that the existing enclosure base has been anchored with 5/8”Ø Kwik Bolt TZ’s. As a result, it is believed that the existing holes are sized for that 5/8”Ø anchor. The first option is to install a 5/8”Ø Kwik Bolt TZ2, similarly to the existing conditions. The second option is to use a threaded insert anchor. Since the largest allowable diameter of HIS-N insert is 1/2”Ø based on the slab thickness, 2”x2” square plate washers with a 9/16”Ø hole will need to be installed on the top of the existing enclosure base plates to reduce the diameter of the existing holes. This is required for the anchorage to provide proper restraint in a seismic event.

42 ENGINEERING↗
DOE OSTI2025

A Semi-supervised Hybrid Machine Learning Framework for the Qualification of Resistance Spot Welds

• Industries requiring high structural integrity, including automotive, aerospace, and construction, place considerable significance on weld quality classification. • The inspection normally involves human expertise through predefined quality metrics that are subjective, error-prone, and time-intensive • The challenge to classification model development is the scarcity of labeled data and imbalanced distributions in the data that are labeled. • This work develops a new hybrid methodology that achieves clustering using KMeans++ together with supervised classification to overcome these challenges. • The ensemble-based classifiers were identified as optimal, with accuracy enhancements of up to 8% using the pseudo-labeled dataset. • The work provides practical insight into feature engineering and machine learning integration in industrial quality assurance applications.

Rogers, Jeremy K. [Savannah River National Laborat↗
DOE OSTI2024

An Engineering Approach for Weld Creep Lifetime Assessment Based on Local Property Measurement

The localized creep failure in the heat-affected zone (HAZ) of Grade 91 steel weldments has been identified as one of the most important factors causing significantly shortened service lifetime and structural integrity issues of welded components in advanced fossil and nuclear power plants. To conduct a reliable creep lifetime assessment, a new engineering assessment approach has been developed by incorporating the experimentally determined local properties of the heterogeneous HAZ. By creep testing a purposely simulated HAZ specimen with in situ digital image correlation (DIC) technique, the highly gradient creep properties across the HAZ of Grade 91 steel was quantitatively measured. A physical creep cavitation constitutive model was proposed to investigate the local creep deformation and damage accumulation within the heterogeneous HAZ, which takes into account the nucleation of creep cavities and their growth by both grain boundary diffusion and creep deformation. The relationship among the local material property, creep strain accumulation, and evolution characteristic of creep cavities was established. The approach was then utilized to investigate the creep response and subsequent life for an ex-service 9% Cr steel weldment by incorporating the effects of pre-existing damages which developed and accumulated during long-term services. The predicted results exhibited quantitative agreement with the DIC measurement in terms of both nominal/local creep deformation as well as the subsequent life under the test conditions at 650 and 80 MPa.

Zhang, Wei↗
DOE OSTI2020

System and method for light assisted friction stir processing and welding of metallic and non-metallic materials

An apparatus for use in a friction stir operation, such as friction stir welding (FSW) or friction stir processing (FSP). The apparatus may have a rotating tool adapted to be plunged into a material, where the material is susceptible to being softened by heating. The rotating tool may further be adapted to be advanced along a surface of the material. An optical energy generating subsystem may be used to heat a portion of the material using optical energy as the tool is advanced along the material.

42 ENGINEERING↗
DOE OSTI2021

Resistance pressure weld for nuclear reactor fuel rod tube end plug

A fuel rod for a nuclear reactor, including a cladding tube having a first end with an annular end face, a second end with an annular end face, and a cylindrical body portion extending therebetween, and a first tube end plug including a front portion, an annular lip with an annular end face, and a substantially straight cylindrical body portion extending therebetween, wherein the surface area of the annular end face of the first end of the cladding tube and the annular end face of the annular lip of the first tube end plug are substantially equal, and the annular end face of the first end of the cladding tube and the annular end face of the annular lip of the first tube end plug are connected by a resistance pressure weld.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Completion of Milestone M3CT-21IN0702028 - Receive Welding Module from IFE (Halden, Norway)

Prior to 2018, the U.S. DOE and the commercial nuclear industry relied upon the Halden Reactor Project’s capability to refabricate and reinstrument previously irradiated fuel rods. This capability has now been lost. This activity is key to recovering that capability and enabling the continuation of critical research on commercial and advanced LWR fuels. This welding module completes the three-module suite the Institute For Energy (IFE) was contracted to deliver to INL. This equipment will be used in FY22 to practice techniques developed at IFE for refabricating and instrumenting prototypical fuel rods.

42 ENGINEERING↗
DOE OSTI2023

A Novel Design for Improving the Control on the Stainless-Steel Vessel Welding Process for Superconducting Magnets

Stainless steel vessels see widespread use in superconducting magnets for particle accelerator applications. Their function varies in different magnet designs: they always provide the necessary liquid helium containment, but in some cases are also used to provide azimuthal prestress and can also be welded to the magnet end plate to provide additional longitudinal stiffness. A magnet designed with the bladder and key technology does not rely on the structural role of the vessel. They are structurally supported using azimuthally prestressed aluminum shells, and the longitudinal constraint by rods. In this case, the magnet designer would generally like to minimize the interaction between the magnet and the stainless-steel vessel and to minimize the coil stress variation due to the vessel. The stress state in the vessel and in the coil is a function of the circumferential interference, defined as the vessel azimuthal length minus the magnet circumference. The vessel and the magnet azimuthal length machining tolerances are relatively large resulting in significant stress variations in the superconducting coils. In this paper we introduce an interference control shim, which can significantly limit the stress variation of the coils for a given variation of the interference. The effectiveness of the interference-control shim is evaluated numerically on the MQXF, the low-β quadrupole for the High Luminosity LHC.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Toolpath considerations for DED: Arc and laser welding

Directed energy deposition (DED) is a form of additive manufacturing that uses localized melted metal, similar to traditional arc welding, to construct an object. In comparison to polymer systems, metal systems can exert additional control over the build process through manipulation of the pool of melted metal, called the “melt pool.” This is especially important to maintain appropriate layer heights and create high quality builds. Additionally, metal systems allow site-specific control of the printed part, which enables advanced construction techniques that would otherwise not be possible. However, both of these types of control require support from the slicing software and, potentially, sensor feedback. This chapter will discuss these control processes and their basic implementation in a slicing program. The processes described here lay the foundation for more advanced solutions, particularly sensor feedback, that will be discussed later.

Borish, Michael↗
DOE OSTI2022

Reinforcing the exit hole from friction stir welding and processing

After friction stir welding/processing (FSW/P), an exit hole remains at the end of the run, which can be the weakest region of the welded/processed workpiece. In addition, tensile residual stress around the exit hole resulting from heating during FSW/P facilitates incipient crack initiating from the exit hole under external loading. Current solutions include removing or repairing the exit hole, which are time-consuming and costly. Here, we propose a novel method to reinforce the exit hole by applying an additional FSW/P pass around it, in a way that replaces preexisting tensile residual stress with compressive residual stress. Under external loading, there is no evident strain accumulation around the exit hole, and the workpiece ultimately fails along the FSW/P heat affected zone. This method provides a more convenient way to reinforce the exit hole than the current exit-hole repair or removal methods for industrial applications.

36 MATERIALS SCIENCE↗