SEARCH · Search NASA

Results for “aviation fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Learnings From the 2022 NREL Partner Forum: Research Needs for Liquid Fuels

During the 2022 Partner Forum at the National Renewable Energy Laboratory (NREL), stakeholders and experts from across aviation came to the whiteboard to outline common goals, align interests, understand technologies, and discuss steps for safely and seamlessly decarbonizing aviation. Experts identified challenges, strategies, and needed research on aviation fuels, infrastructure, and aircraft. Initial insights, strategies, and high-level suggestions from a focused sustainable aviation fuel (SAF) workshop are summarized below, including potential barriers and synergies for achieving bold decarbonization goals.

aviation↗

DOE OSTI2025

Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels

Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.

09 BIOMASS FUELS↗

DOE OSTI2022

Measuring Critical Fuel Properties for Simulations to Accelerate Fuel Qualification

NREL's sustainable aviation fuel (SAF) research in the area of fuel properties and end use is focused on accelerating SAF development and deployment. This will be achieved by close collaboration with BETO program researchers on fuel property measurement and development of structure-property relationships. Additionally, fuel properties measured at often extreme engine operating conditions will be measured, and will be used as inputs to exascale ready simulations of aviation combustion turbines to reveal impacts of properties on turbine operation. This research will potentially lead to a widening of the allowable fuel property range for SAF, expanding SAF production process options and production volumes.

ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Co-Hydrotreatment of Yellow Greases and the Water-Insoluble Fraction of Pyrolysis Oil. Part I: Experimental Design to Increase Kerosene Yield and Reduce Coke Formation

Here, this paper reports the co-hydrotreatment of Biomass Technology Group commercial pyrolysis oil water-insoluble (WIS) phase (also known as pyrolytic lignin) and yellow greases (waste cooking oil), aiming to produce sustainable aviation fuels (SAFs). We use a sulfided NiMo/Al 2 O 3 blend with 16 wt % WIS and a central composite experimental design to identify processing conditions increasing kerosene yield and reducing coke formation. The input variables were: (1) reaction temperature (320, 350, and 380 °C), (2) initial hydrogen pressure (5, 6, and 7 MPa), and (3) amount of catalyst (0.7, 1.0, and 1.3 g). The hydrotreated oily phases were distilled to obtain gasoline (<150 °C), kerosene (150–250 °C), diesel (250–350 °C), and residual oil (>350 °C). The reaction temperature is the main factor affecting the yield of gaseous, solid, and liquid products. Meanwhile, a higher initial hydrogen pressure and catalyst loading increased the yield of kerosene and other distillates and decreased the coke formation. A high temperature correlated with a lower content of oxygenates in kerosene cuts. Based on our experimental results, we propose to conduct hydrotreatment studies at 380 °C, initial H 2 pressure of 7 MPa, and 1.3 g of catalyst. Under the identified conditions, it was possible to improve the kerosene yield to more than 20 wt % and reduce the yield of coke to close to 2.0 wt %. The chemical composition and fuel properties of the gasoline, kerosene, and diesel cuts were thoroughly analyzed. The content of aromatics and phenols in the kerosene fraction produced at the conditions identified in this project exceeded the recommended values for SAFs. New strategies (such as blending and more intense hydrotreatment to remove oxygenated compounds) need to be implemented to reduce the content of these molecules in our final product.

09 BIOMASS FUELS↗

DOE OSTI2025

Meeting liquid biofuel and bioproduct goals: biotechnological design of the intermediate oilseeds pennycress and camelina, and beyond

The European Union and the United States have set ambitious goals to produce biofuels as part of broader decarbonization and energy security initiatives. One of the more feasible routes to liquid biofuels production is the conversion of seed oils [triacylglycerols (TAGs)] to renewable diesel, biodiesel, and sustainable aviation fuel (SAF) using the hydrotreated ester and fatty acids (HEFA) process. Camelina and pennycress are attractive oilseed feedstocks in that they can be grown in the offseason as intermediate crops on tens of millions of hectares of farmland annually, providing ecosystem benefits and not competing with established food crops. Considerably more TAG could be produced by engineering vegetative portions of crops such as sorghum and miscanthus to accumulate economically-viable amounts. Here, this review highlights recent advances in developing pennycress and camelina as intermediate oilseed crops not only for biofuels production but for making higher value oils such as those enriched in astaxanthin, vitamin E, and medium-chain fatty acids. Given the magnitude of renewable liquid fuel demands, we also describe how advances in oil production from vegetative parts of biomass crops can complement intermediate oilseed cropping systems to meet biofuel and bioproduct targets.

biomass crops↗

DOE OSTI2022

Modeling Yield, Biogenic Emissions, and Carbon Sequestration in Southeastern Cropping Systems With Winter Carinata

Sustainable aviation fuel (SAF) production from lipids is a technologically mature approach for replacing conventional fossil fuel use in the aviation sector, and there is increasing demand for such feedstocks. The oilseed Brassica carinata (known as Ethiopian mustard or simply carinata) is a promising SAF feedstock that can be grown as a supplemental cash crop over the winter fallow season of various annual crop rotations in the Southeast US, avoiding land use changes and potentially achieving some of the soil carbon sequestration and ecosystem service benefits of winter cover crops. However, carinata may require more intensive management than traditional cover crops, potentially leading to additional soil greenhouse gas (GHG) emissions through increased carbon losses from soil tillage and nitrous oxide (N 2 O) emissions from nitrogen fertilizer application. In this work, the 2017 version of the process-based DayCent ecosystem model was used to establish initial expectations for the total regional SAF production potential and associated soil GHG emissions when carinata is integrated as a winter crop into the existing crop rotations across its current suitability range in southern Alabama, southern Georgia, and northern Florida. Using data from academic and industry carinata field trials in the region, DayCent was calibrated to reproduce carinata yield, nitrogen response, harvest index, and biomass carbon-to-nitrogen ratio. The resulting model was then used to simulate the integration of carinata every third winter across all 2.1 Mha of actively cultivated cropland in the study area. The model predicted regional average yields of 2.9–3.0 Mg carinata seed per hectare depending on crop management assumptions. That results in the production of more than two million Mg of carinata seed annually across the study area, enough to supply approximately one billion liters of SAF. Conventional management of carinata led to only modest increases in soil carbon storage that were largely offset by additional N2O emissions. Climate-smart management via adopting no-till carinata establishment or using poultry litter as a nitrogen source resulted in a substantial net soil GHG sink (0.23–0.31 Mg CO 2 e ha -1 y -1 , or 0.24–0.32 Mg CO2e per Mg of seed produced) at the farms where carinata is cultivated.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2009

Synthetic and Biomass Alternate Fueling in Aviation

Must use earth's most abundant natural resources - Biomass, Solar, Arid land (43%), Seawater (97%) with nutrients (80%) plus brackish waters and nutrients resolve environmental triangle of conflicts energy-food-freshwater and ultrafine particulate hazards. Requires Paradigm Shift - Develop and Use Solar* for energy; Biomass for aviation and hybrid-electric-compressed air mobility fueling with transition to hydrogen long term.

Hendricks, Robert C.↗

DOE OSTI2020

Autoignition delay times measurements of linear unsaturated jet fuel compounds inside a shock tube

Autoignition delay times measurements and CO time histories were studied for 2-pentene, a hydrocarbon in aviation fuel and an important species in the development of aviation fuel surrogates. Three mechanisms from the literature were compared against the measured data, and a sensitivity analysis for CO was performed for all mechanisms. Shock tube experiments were performed between 1246 K – 1372 K and 8.8 atm – 9.3 atm at an equivalence ratio of 1, a fuel loading of 0.25% was used and was balanced in oxygen and argon. Discrepancies between the available literature mechanisms exist, the measured data herein is essential for validation of these mechanisms and the reduction of validated mechanisms for coupling into CFD.

09 BIOMASS FUELS↗

DOE OSTI2026

Data for Development of Vegetative Oil Sorghum: From Lab-to-Field

Biomass crops engineered to accumulate energy-dense triacylglycerols (TAG or ‘vegetable oils’) in their vegetative tissues have emerged as potential feedstocks to meet the growing demand for renewable diesel and sustainable aviation fuel (SAF). Unlike oil palm and oilseed crops, the current commercial sources of TAG, vegetative tissues, such as leaves and stems, only transiently accumulate TAG. In this report, we used grain (Texas430 or TX430) and sugar-accumulating ‘sweet’ (Ramada) genotypes of sorghum, a high-yielding, environmentally resilient biomass crop, to accumulate TAG in leaves and stems. We initially tested several gene combinations for a ‘push-pull-protect’ strategy. The top TAG-yielding constructs contained five oil transgenes for a sorghum WRINKLED1 transcription factor (‘push’), a Cuphea viscosissima diacylglycerol acyltransferase (DGAT; ‘pull’), a modified sesame oleosin (‘protect’) and two combinations of specialized Cuphea lysophosphatidic acid acyltransferases and medium-chain acyl-acyl carrier protein thioesterases. Though intended to generate oils with medium-chain fatty acids, engineered lines accumulated oleic acid-rich oil to amounts of up to 2.5% DW in leaves and 2.0% DW in stems in the greenhouse, 36-fold and 49-fold increases relative to wild-type (WT) plants, respectively. Under field conditions, the top-performing event accumulated TAG to amount to 5.5% DW in leaves and 3.5% DW in stems, 78-fold and 58-fold increases, respectively, relative to WT TX430. Transcriptomic and fluxomic analyses revealed potential bottlenecks for increased TAG accumulation. Overall, our studies highlight the utility of a lab-to-field pipeline coupled with systems biology studies to deliver high vegetative oil sorghum for SAF and renewable diesel production.

Biofuels↗

DOE OSTI2026

Data for Multisite Field Evaluation of Oil Accumulation and Agronomic Performance in Grain and Sweet Sorghums Engineered for Lipid Hyperaccumulation

Oil sorghum (OS) has been developed by engineering grain (TX430) and sweet (Ramada) genetic backgrounds to accumulate triacylglycerols (TAG) in vegetative tissues as an energy-dense feedstock for sustainable aviation fuel (SAF) and other biofuels. This study evaluated two TX430 OS lines (TxHO-2, TxHO-3) and two Ramada OS lines (RmHO-1, RmHO-2) alongside wild-type (WT) lines in NE and IL over 2 years (2023–2024) to quantify genotype × environment effects on agronomic performance and TAG accumulation. Across four environments, TX430 OS lines showed average TAG concentrations of 15.0 g kg−1 in leaves and 12.8 g kg−1 in stems, approximately 19-fold higher than WT. Ramada OS lines accumulated 26.1 g kg−1 in leaves and 12.3 g kg−1 in stems, approximately 25-fold and 13-fold increases over WT, respectively. OS lines in TX430 exhibited an 18% reduction in biomass (8.4 vs. 9.9 Mg ha−1 for WT), while Ramada OS lines had similar WT biomass (18.3 vs. 19.9 Mg ha−1 for WT). Among TX430 OS lines, TxHO-2 achieved the highest TAG yield (190 kg ha−1), while RmHO-1 led the Ramada lines (335 kg ha−1) due to higher biomass and similar TAG concentration. Enhanced TAG accumulation increased N, P, and K removal in TX430 lines but not in Ramada lines. Structural carbohydrate and ash concentration were unaffected. Overall, results confirm vegetative lipid accumulation as a viable strategy for high-biomass sorghum, supporting its potential as a dual-purpose feedstock for SAF. Future work should focus on minimizing biomass yield penalties and improving nutrient use efficiency in oil sorghum systems.

Agronomy↗

DOE OSTI2021

Microchannel Reactor for Ethanol to Butene: CRADA 503 [Abstract only]

A key challenge facing most bioprocessing operations is that multiple unit operations are required, thereby resulting in complex, energy-intensive, and expensive processes. Further, biomass transportation costs drive the need for smaller, distributed processing plants. To incorporate the smaller scales desirable for biomass, novel processes must be developed with reduced capital costs. With over 20 years of experience in the development and commercialization of microchannel reactor technology, Oregon State University will partner with Pacific Northwest National Laboratory to demonstrate a microchannel reactor with lower capital costs for an alcohol-to-jet (ATJ) process technology that is currently being commercialized by LanzaTech. Ethanol can be produced from biomass feedstocks such as LanzaTech’s proprietary biochemical process using carbon from a number of possible feedstocks; syngas generated from biomass resources (e.g., MSW, organic industrial waste, agriculture waste) or reformed biogas, or from other biomass feedstocks such as corn kernel fiber. Ethanol then undergoes catalytic dehydration to form ethylene followed by a two-step oligomerization, hydrogenation, and fractionation to control the hydrocarbon product slate to the jet-range. Successful process development aided by a market pull for low carbon aviation fuel has spurred scale-up and commercial demonstration. However, Sustainable Aviation Fuel is a very price sensitive market and improved economics through process intensification will make the current ATJ process even more attractive. Recent efforts at PNNL have culminated in the development of a new catalyst technology for the conversion of ethanol to n-butene-rich olefins. A greater than 90% conversion, total olefin selectivity of 80-90% (n-butene selectivity ~60%), and good stability over a 100 hour test duration has been demonstrated at the bench scale. Producing butene-rich olefins directly from ethanol with high yield is new and impactful because the higher olefins can be selectively oligomerized to distillate-range hydrocarbons, thus eliminating one process step from the current ATJ process. Further, coupling the severely endothermic ethanol dehydration with exothermic C-C bond formation results in more energy efficient processing. Additional intensification and energy savings will stem from incorporating this new ethanol to n-butene catalyst technology within the ATJ process implemented using a microchannel reactor platform. Due to recent advances in microchannel manufacturing methods and associated cost reductions we believe the time is right to adapt this technology toward new commercial bioconversion applications.

02 PETROLEUM↗

DOE OSTI2024

Economic, Greenhouse Gas, and Resource Assessment for Fuel and Protein Production from Microalgae: 2022 Algae Harmonization Update

This report presents an updated “harmonization study” documenting the collaborative analysis of saline microalgae cultivation and conversion to fuels and products. Four national laboratory modeling teams reconvened to investigate the resource, economic, and environmental sustainability implications of integrated systems encompassing large-scale algae farms and conversion biorefineries. Relative to prior harmonization analyses conducted by these partners, the present effort focuses on more near-term technology potential based on the use of nutrient-replete, high-protein algal biomass compositions (more readily achievable today without sacrificing cultivation productivity) coupled with individual algae farms varying in size but generally smaller at 3,900 acres on average (more realistic in practice than a fixed 5,000-acre farm scale previously considered). Additionally, the present assessment adds further granularity around carbon dioxide (CO 2 ) sourcing and transport via carbon capture of nearby point sources, as well as handling of high-saline cultivation media and resultant blowdown/disposal processing. Finally, this assessment focuses on conversion opportunities to produce both fuel (prioritizing sustainable aviation fuel [SAF], in this case via hydrothermal liquefaction) and protein products for the food and feed markets, recognizing growing needs for such products.

09 BIOMASS FUELS↗

NASA NTRS1980

Outlook for alternative energy sources

Predictions are made concerning the development of alternative energy sources in the light of the present national energy situation. Particular emphasis is given to the impact of alternative fuels development on aviation fuels. The future outlook for aircraft fuels is that for the near term, there possibly will be no major fuel changes, but minor specification changes may be possible if supplies decrease. In the midterm, a broad cut fuel may be used if current development efforts are successful. As synfuel production levels increase beyond the 1990's there may be some mixtures of petroleum-based and synfuel products with the possibility of some shale distillate and indirect coal liquefaction products near the year 2000.

Card, M. E.↗

NASA NTRSDate not supplied

True Zero Emission Electric Aircraft Propulsion Transport Technology

This work establishes and describes a new electric aircraft propulsion technology category for achieving true zero greenhouse gas emission with transport aircraft. This new category is enabled by a recently invented Closed Strayton Quad Generator and recently developed megawatt-scale electric propulsor motors that enable staged contra-rotating ducted fans in a single nacelle. After a brief review of the existing state of practice, a new electric aircraft propulsion system is described that is quiet, clean, efficient, reliable, safe and supports the global transition from jet fuel and sustainable aviation fuel to future green hydrogen fuel with the goal of achieving truly zero impact on the environment. A detailed design of this propulsion system is presented along with a performance and mass comparison to current state of practice.

Closed↗

NASA NTRSDate not supplied

True Zero Emission Electric Aircraft Propulsion Transport Technology

Closed↗

DOE OSTI2025

Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane

Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)─ produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.

09 BIOMASS FUELS↗

DOE OSTI2023

A general predictive methodology for fuel-mixture properties up to supercritical conditions

A predictive thermodynamic model is utilized for the calculation of fuel properties of oxymethylene dimethyl ethers (OME 3–4 ), surrogates for gasoline, diesel and aviation fuel, as well as alcohol blends with gasoline and diesel. The alcohols used for these blends are methanol, ethanol, propanol, butanol and pentanol; their mixing ratio ranges from 10 to 50% by volume. The model is based on the Perturbed-Chain Statistical Association Fluid Theory (PC-SAFT) equation of state (EoS) and Vapor Liquid Equilibrium (VLE) calculations at constant temperature, density and composition. The model includes the association term, with the assumption of two association sites (2B scheme), to enable the modeling of alcohols. The pure-component parameters are estimated based on the Group Contribution (GC) method of various sources, as well as a parametrization model specifically designed for the case of OME 3–4 . The results of the computational model for the density, vapor pressure and distillation curves at various conditions, including high-pressure, high-temperature (HPHT), are compared to experimental and computational data available in the literature. In the cases where no measurements are available for the surrogates, experimental data for the corresponding target fuel are used, taking into consideration the inherent deviation in properties between real and surrogate fuel. Overall, the results are in good agreement with the data from the literature, with the average deviation not exceeding 12% for temperature (Kelvin) on the distillation curves, 10% for density and 46% for vapor pressure and the general trend being captured successfully. The use of different pure component parameter estimation techniques can further improve the prediction quality in the cases of OME3–4 and the aviation fuel surrogate, especially for the vapor pressure, leading to an average deviation lower than 18%. These results demonstrate the predictive capabilities of the model, which extend to a wide range of fuel types and pressure/temperature conditions. Through this investigation, the present work aims to establish the limits of applicability of this thermodynamic property prediction methodology.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS2026

Fuel Heating System Design and Thermal Modeling for Aviation Combustion Research

Aviation fuels offer substantial heat-sink capability that can be applied to aircraft thermal-management strategies and advanced propulsion-system concepts. Accurate control of fuel temperature is critical for understanding combustion behavior and supporting high temperature fuel experimental studies. This work describes the modeling and experimental validation of a portable, high temperature fuel-conditioning system designed for multiple NASA Glenn Research Center’s combustion facilities. The system utilizes a circulating-oil heating unit and modular tube-in-tube heat exchangers capable of conditioning Jet-A to temperatures approaching 600 K. A Thermal Desktop model was created to analyze heat exchanger configurations and predict performance across a range of operating conditions. Model predictions were compared with measurements collected in the CE-13C test facility, showing good agreement across the tested flow range except at low fuel flow rate around 2 kg/hr. Results provide guidance for sizing future fuel heating system for combustion research applications.

Jet fuel heating system↗