Search NASA⌕ Search

SEARCH · Search NASA

Results for “buffer layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Giant magnetoresistance in organic spin valves

Interfacial diffusion between magnetic electrodes and organic spacer layers is a serious problem in the organic spintronics which complicates attempts to understand the spin-dependent transport mechanism and hurts the achievement of a desirably high magnetoresistance (MR). We deposit nanodots instead of atoms onto the organic layer using buffer layer assist growth. Spin valves using this method exhibit a sharper interface and a giant MR of up to {approx}300%. Analysis of the current-voltage characteristics indicates that the spin-dependent carrier injection correlates with the observed MR.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural characterization of two-step growth of epitaxial ZnO films on sapphire substrates at low temperatures

We have investigated two-step growth of high-quality epitaxial ZnO films, where the first layer--the buffer layer (nucleation layer template)--is grown at a low temperature (230-290 C) to induce a smooth (two-dimensional) growth. This is followed by growth at a moderate temperature {approx}430 C to form high-quality smooth ZnO layers for device structures. It was possible to reduce the growth temperature to 250-290 C and obtain a smooth epitaxial template layer on sapphire (0 0 0 1) substrates with surface roughness less than 1 nm. After the high-temperature growth, the film surface undulations (roughness) increased to about 2 nm, but it is still quite smooth. The calculation of c and a lattice parameters by high-resolution x-ray diffraction shows that the a lattice parameter is fully relaxed at the growth temperatures but the c lattice parameter is dependent on the defect concentration in the growing film. A decoupling between a and c lattice parameters of the films is observed, which leads to abnormal Poisson's ratios ranging from 0.08 to 0.54. The decoupling of the lattice parameters is analyzed based on growth characteristics and the presence of strain and defects in the grown films. We present our detailed studies on the nature of epitaxy, defects and interfaces by using comprehensive x-ray diffraction and high-resolution TEM studies.

36 MATERIALS SCIENCE↗

Layer dependence of graphene-diamene phase transition in epitaxial and exfoliated few-layer graphene using machine learning

The study of the nanomechanics of graphene—and other 2D materials—has led to the discovery of exciting new properties in 2D crystals, such as their remarkable in-plane stiffness and out of plane flexibility, as well as their unique frictional and wear properties at the nanoscale. Recently, nanomechanics of graphene has generated renovated interest for new findings on the pressure-induced chemical transformation of a few-layer thick epitaxial graphene into a new ultra-hard carbon phase, named diamene. Here in this work, by means of a machine learning technique, we provide a fast and efficient tool for identification of graphene domains (areas with a defined number of layers) in epitaxial and exfoliated films, by combining data from atomic force microscopy (AFM) topography and friction force microscopy (FFM). Through the analysis of the number of graphene layers and detailed Å-indentation experiments, we demonstrate that the formation of ultra-stiff diamene is exclusively found in 1-layer plus buffer layer epitaxial graphene on silicon carbide (SiC) and that an ultra-stiff phase is not observed in neither thicker epitaxial graphene (2-layer or more) nor exfoliated graphene films of any thickness on silicon oxide (SiO 2 ).

36 MATERIALS SCIENCE↗

Polycrystalline ferroelectric or multiferroic oxide articles on biaxially textured substrates and methods for making same

A polycrystalline ferroelectric and/or multiferroic oxide article includes a substrate having a biaxially textured surface; at least one biaxially textured buffer layer supported by the substrate; and a biaxially textured ferroelectric or multiferroic oxide layer supported by the buffer layer. Methods for making polycrystalline ferroelectric and/or multiferroic oxide articles are also disclosed.

36 MATERIALS SCIENCE↗

Origins of interlayer formation and misfit dislocation displacement in the vicinity of InAs/GaAs quantum dots

We have examined the origins of interlayer formation and misfit dislocation (MD) displacement in the vicinity of InAs/GaAs quantum dots (QDs). For QDs formed by the Stranski-Krastanov mode, regularly spaced MDs nucleate at the interface between the QD and the GaAs buffer layer. In the droplet epitaxy case, both In island formation and In-induced “nano-drilling” of the GaAs buffer layer are observed during In deposition. Upon annealing under As flux, the In islands are converted to InAs QDs, with an InGaAs interlayer at the QD/buffer interface. Meanwhile, MDs nucleate at the QD/interlayer interface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Interplay between strain, quantum confinement, and ferromagnetism in strained ferromagnetic semiconductor (In,Fe)As thin films

We systematically investigated the influence of strain on the electronic structure and ferromagnetism of (In,Fe)As thin films. It is found that while the shift of the critical point energies of compressive-strained (In,Fe)As layers grown on (In{sub 1−y},Ga{sub y})As (y = 0.05, 0.1) buffer layers can be explained by the hydrostatic deformation effect (HDE) alone, those of tensile-strained (In,Fe)As layers grown on (Ga{sub 1−z},Al{sub z})Sb (z = 0, 0.5, 1) buffer layers can be explained by the combination of HDE and the quantum confinement effect (QCE). The Curie temperature T{sub C} of the (In,Fe)As layers strongly depends on the strain, and shows a maximum for the (In,Fe)As layer grown on a GaSb buffer layer. The strain dependence of T{sub C} can be explained by the s-d exchange mechanism taking into account HDE and QCE.

36 MATERIALS SCIENCE↗

Over 11% Efficient Eco-Friendly Kesterite Solar Cell: Effects of S-Enriched Surface of Cu2ZnSn(S,Se)4 Absorber and Band Gap Controlled (Zn,Sn)O Buffer

For high efficiency kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cell, CdS thin film was usually used as a buffer layer. However, due to the toxicity of Cd and pollution problems involved from the solution-based chemical bath deposition, eco-friendly high efficiency CZTSSe solar cell with Cd-free buffer is necessary. As an Cd-free buffer layer, we investigated (Zn,Sn)O (ZTO) film deposited by sputtering method. In order to achieve high power conversion efficiency, we controlled energy band gaps of CZTSSe absorber as well as ZTO buffer, which was required to optimize conduction band offset (CBO) between the absorber and the buffer and to increase open circuit voltage (Voc) and fill factor (FF). The CBO was optimized by controlling the band gap of ZTO. By varying the Sn/(Zn + Sn) ratio and its deposition temperature, band gap of ZTO was successfully adjusted. Experimental and computational calculation results showed that solar cell performance was strongly affected by the CBO between absorber and buffer. Besides CBO matching, larger band gap of ZTO improved short circuit current density (Jsc) with enhanced external quantum efficiency value in blue photon spectrum range. As an additional way to improve power conversion efficiency of solar cell, band graded CZTSSe absorber was developed by using spray-based two-step process. The sprayed CZTSSe film was engineered to have S-enriched surface, which makes surface band gap widened and surface passivated, and resultantly increases Voc, Jsc and fill factor (FF). By controlling band gaps of both CZTSSe absorber and ZTO buffer, we obtained 11.22% environment-friendly CZTSSe solar cell without MgF2 anti-reflection coating.

(Zn↗

The growth of GaSb/Al{sub 0.33}Ga{sub 0.67}Sb MQW on n-Silicon (1 0 0) with Al{sub 0.66}Ga{sub 0.34}Sb/AlSb SPS layers

Highlights: • GaSb/Al{sub 0.33}GaSb MQW layer was grown on Si (1 0 0) by MBE. • The effect of miscut angle of Si substrate was studied. • A lot of twins were removed by Al{sub 0.66}Ga{sub 0.34}Sb/AlSb SPS layers. • Good quality of GaSb/Al{sub 0.33}Ga{sub 0.67}Sb MQW layers were proved by PL spectra. • Optimum growth temperature of the AlSb buffer layer was studied. - Abstract: GaSb/Al{sub 0.33}Ga{sub 0.67}Sb multi-quantum well (MQW) film on n-Si (1 0 0) substrates is grown by molecular beam epitaxy. The effects of a miscut angle of the Si substrate (0°, 5°, and 7°) on the properties of an AlSb layer were also studied. The suppression of the anti-phase domains (APD) was observed at a miscut angle of 5° on Si (1 0 0). It was found that the growth temperature in the range of 510–670 °C affects the quality of AlSb layers on Si. Low root-mean-square surface (RMS) roughness values of 3–5 nm were measured by atomic force microscopy at growth temperatures ranging from 550 °C to 630 °C. In addition, Al{sub 0.66}Ga{sub 0.34}Sb/AlSb short period superlattice (SPS) layers were used to overcome problems associated with a large lattice mismatch. The RMS values of samples with a SPS were partially measured at approximately ∼1 nm, showing a larger APD surface area than samples without a SPS layer. Bright-field cross-sectional transmission electron microscopy images of the GaSb/Al{sub 0.33}Ga{sub 0.67}Sb MQW, the AlSb buffer layer and the Al{sub 0.66}Ga{sub 0.34}Sb/AlSb SPS layers show that numerous twins from the AlSb/Si interface were removed by the AlSb buffer layer and the Al{sub 0.66}Ga{sub 0.34}Sb/AlSb SPS. The GaSb/Al{sub 0.33}Ga{sub 0.67}Sb MQW PL spectra were obtained at 300 K and 10 K with a fixed excitation power of 103 mW. Emission peaks appeared at 1758 nm and 1620 nm, respectively.

36 MATERIALS SCIENCE↗

Electron Microscopic Examination of an Irradiated TRISO Coated Particle of AGR-2 Experiment: AGR2-222-RS019

The transmission electron microscopic (TEM) examination of an irradiated tristructural isotropic (TRISO) coated particle from advanced gas reactor (AGR) 2 fuel Compact 2-2-2 is presented in this report. Compact 2-2-2 refers to the compact in Capsule 2 at Level 2 of Stack 2. The examination on AGR2 222 RS019 is focused on the interface between the silicon carbide (SiC) to inner pyrolytic carbon (IPyC) layer, central part of SiC, and the interface between SiC and outer pyrolytic carbon layer. The SiC grain boundary distribution and associated fission product precipitates were characterized by scanning transmission electron microscopy (STEM) energy dispersive spectroscopy (EDS), and precession electron diffraction (PED) in the transmission electron microscope. Two separate locations on SiC layer were selected for on the basis of the intact of the buffer layer in the irradiated TRISO particle. The key observation in this particle is that the compositional nature of grain boundary precipitates is more complex near IPyC/SiC layer where Pd, Pd-Ag, Pd-U containing precipitates can be observed. However, the compositions of precipitate towards outer most region of SiC mainly contain Pd. Ag has been observed in the IPyC/SiC layer in one of the two locations. Comparison of the results to previously irradiated and analyzed, Variant 3, safety tested AGR-1 TRISO particles (AGR1-433-001 and AGR1 222-RS004) showed the grain boundary distributions have some noticeable differences. The differences in coincident site lattice grain boundary and misorientation angles are possibly inherent to the fabrication process. Neutron irradiation induced void distribution has been found to be nonuniform. A high concentration of smaller voids is found at stacking faults compared to those in the SiC matrix. Larger void sizes are observed in the SiC location that is near to the broken buffer layer. This void size variation with integrity of buffer layer can potentially affect the fission product retention. However, the average void size continuously decreases along the radius of SiC in both locations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Acceptance Test Data for the AGR-5/6/7 Irradiation Test Fuel Composite Defective IPyC Fraction and Pyrocarbon Anisotropy

Coated particle composite J52R-16-98005 was produced by Babcock and Wilcox Technologies (BWXT) as fuel for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR). This composite was comprised of four coated particle fuel batches J52O-16-93165B (26%), 93168B (26%), 93169B (24%), and 93170B (24%), chosen based on the Quality Control (QC) data acquired for each individual candidate AGR-5/6/7 batch. Each batch was coated in a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace. Tristructural isotropic (TRISO) coatings were deposited on 425-μm-nominal-diameter spherical kernels from BWXT Lot J52R-16-69317 containing a mixture of 15.5%-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μm-nominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. The TRISO-coated particle batches were sieved to upgrade the particles by removing over-sized and under-sized material, and the upgraded batches were designated by appending the letter A to the end of the batch number (e.g., 93165A). Secondary upgrading by sieving was performed on the A-designated batches to remove particles with missing or very-thin buffer layers that were identified during previous analysis of the individual batches for defective IPyC, as reported in the acceptance test data report for the AGR-5/6/7 production batches [Hunn et al. 2017]. The additionally-upgraded batches were designated by appending the letter B to the end of the batch number (e.g., 93165B).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Acceptance Test Data for BWXT Coated Particle Batches 93172B and 93173B—Defective IPyC and Pyrocarbon Anisotropy

Coated particle batches J52O-16-93172B and J52O-16-93173B were produced by Babcock and Wilcox Technologies (BWXT) as part of the production campaign for the Advanced Gas Reactor Fuel Development and Qualification (AGR) Program’s AGR-5/6/7 irradiation test in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR), but were not used in the final fuel composite. However, these batches may be used as demonstration production-scale coated particle fuel for other experiments. Each batch was coated in a 150-mm-diameter production-scale fluidized-bed chemical vapor deposition (CVD) furnace. Tristructural isotropic (TRISO) coatings were deposited on 425-μm-nominal-diameter spherical kernels from BWXT lot J52R-16-69317 containing a mixture of 15.5%-enriched uranium carbide and uranium oxide (UCO). The TRISO coatings consisted of four consecutive CVD layers: a ~50% dense carbon buffer layer with 100-μm-nominal thickness, a dense inner pyrolytic carbon (IPyC) layer with 40-μm-nominal thickness, a silicon carbide (SiC) layer with 35-μm-nominal thickness, and a dense outer pyrolytic carbon (OPyC) layer with 40-μm-nominal thickness. The TRISO-coated particle batches were sieved to upgrade the particles by removing over-sized and under-sized material, and the upgraded batches were designated by appending the letter A to the end of the batch number (e.g., 93172A). Secondary upgrading by sieving was performed on the A-designated batches to remove particles with missing or very-thin buffer layers that were identified during previous analysis of the individual batches for defective IPyC, as reported in the acceptance test data report for the AGR-5/6/7 production batches [Hunn et al. 2017b]. The additionally-upgraded batches were designated by appending the letter B to the end of the batch number (e.g., 93172B).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pulsed Laser Deposition and Characterization of Heteroepitaxial LiMn 2 O 4 /La 0.5 Sr 0.5 CoO 3 Bilayer Thin Films as Model Lithium Ion Battery Cathodes

Epitaxial LiMn 2 O 4 (LMO)/La 0.5 Sr 0.5 CoO 3 (LSCO) bilayer thin films were grown on single crystalline SrTiO 3 (STO) (111) substrates as model lithium ion battery cathodes. The LSCO layer was used as an electrically conducting buffer layer for electrochemical testing. The LMO and LSCO layers were both epitaxial, with sub-nano flat LMO/LSCO interfaces as seen by X-ray diffraction, synchrotron X-ray scattering, and high-resolution transmission electron microscopy (HRTEM), but with a large LMO surface roughness due to the relatively large lattice mismatch with LSCO. Three-dimensional islands and depressions were formed on the strain-relaxed LMO layer, and misfit dislocations at the LMO/LSCO interface were discerned through HRTEM imaging, suggesting a Stranski–Krastanov (SK) mode thin-film growth. A crystalline structural change from cubic spinel at the LMO surface and interior to tetragonal oxygen-deficient LMO at the LMO/LSCO interface was examined. Furthermore, electrochemical tests along with in situ synchrotron X-ray scattering measurements on the epitaxial LMO/LSCO bilayers showed a significant loss of capacity after the first cycle, which was attributed to an electrical conductivity loss of the LSCO buffer layer due to irreversible lattice oxygen loss.

25 ENERGY STORAGE↗

Atomic Layer Deposition of Vanadium Oxide to Reduce Parasitic Absorption and Improve Stability in n-i-p Perovskite Solar Cells for Tandems

Two critical issues associated with semi-transparent, n-i-p perovskite solar cells for 2-terminal tandem devices are parasitic absorption and long-term instability associated with the widely used spiro-OMeTAD and MoOx hole transport and buffer layers, respectively. In this work, we present an alternative hole contact bilayer that consists of a 30 nm undoped layer of spiro-TTB in conjunction with 9 nm of air-stable vanadium oxide (VOx) deposited via atomic layer deposition. The low absorption of UV and visible light in this bilayer results in the fabrication of a semi-transparent perovskite cell with 18.9 mA cm-2 of photocurrent, a 14% increase compared to the 16.6 mA cm-2 generated in a control device with 150 nm of doped spiro-OMeTAD. The ALD VOx buffer layer shows promise as a stable alternative to MoOx; an unencapsulated Cs0.17FA0.83Pb(Br0.17I0.83)3 device with ALD VOx and ITO as the top contact maintains its efficiency following 1000 hours at 85 degrees C in a N2 environment. Lastly, we use transfer matrix modeling of the optimized perovskite stack to predict its optical performance in a monolithic tandem cell with heterojunction silicon.

14 SOLAR ENERGY↗

Strain control of AlGaN/GaN high electron mobility transistor structures on silicon (111) by plasma assisted molecular beam epitaxy

This paper reports on the use of plasma assisted molecular beam epitaxy of AlGaN/GaN-based high electron mobility transistor structures grown on 4 in. Si (111) substrates. In situ measurements of wafer curvature during growth proved to be a very powerful method to analyze the buffer layer's thickness dependent strain. The Ga/N ratio at the beginning of growth of the GaN buffer layer is the critical parameter to control the compressive strain of the entire grown structure. An engineered amount of compressive strain must be designed into the structure to perfectly compensate for the tensile strain caused by differences in the thermal expansion coefficient between the epi-layer and substrate during sample cool down from growth temperatures. A maximum film thickness of 4.2 {mu}m was achieved without the formation of any cracks and a negligible bow of the wafers below 10 {mu}m. Measurement of the as-grown wafers revealed depth profiles of the charge carrier concentration comparable to values achieved on SiC substrates and mobility values of the two dimensional electron gas in the range 1230 to 1350 cm{sup 2}/Vs at a charge carrier concentration of 6.5-7 10{sup 12}/cm{sup 2}. First results on processed wafers with 2 {mu}m thick buffer layer indicate very promising results with a resistance of the buffer, measured on 200 {mu}m long contacts with 15 {mu}m pitch, in the range of R > 10{sup 9}{Omega} at 100 V and breakdown voltages up to 550 V.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of electron collecting metal oxide layer in normal and inverted structure polymer solar cells

We performed a systematic study of the effect of electron collecting metal oxide layer on the performance of P3HT: PCBM solar cells. Zinc oxide (ZnO) or titanium dioxide (TiO{sub 2}) buffer layers were prepared by either e-beam evaporation or solution processing method. We also compared the photovoltaic performance of inserting the buffer layer between indium tin oxide (ITO) and the polymer layer for the inverted structure (ITO/ ZnO or TiO{sub 2}/P3HT:PCBM/V{sub 2}O{sub 5}/Au) as well as inserting the buffers layers between the polymer and the aluminum electrode for the conventional structure (ITO/V{sub 2}O{sub 5}/P3HT:PCBM/ZnO or TiO{sub 2}/Al). The results are shown in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Combinatorial Reactive Sputtering of In2S3 as an Alternative Contact Layer for Thin Film Solar Cells

High-throughput computational and experimental techniques have been used in the past to accelerate the discovery of new promising solar cell materials. An important part of the development of novel thin film solar cell technologies, that is still considered a bottleneck for both theory and experiment, is the search for alternative interfacial contact (buffer) layers. The research and development of contact materials is difficult due to the inherent complexity that arises from its interactions at the interface with the absorber. A promising alternative to the commonly used CdS buffer layer in thin film solar cells that contain absorbers with lower electron affinity can be found in ..beta..-In2S3. However, the synthesis conditions for the sputter deposition of this material are not well-established. Here, In2S3 is investigated as a solar cell contact material utilizing a high-throughput combinatorial screening of the temperature-flux parameter space, followed by a number of spatially resolved characterization techniques. It is demonstrated that, by tuning the sulfur partial pressure, phase pure ..beta..-In2S3 could be deposited using a broad range of substrate temperatures between 500 degrees C and ambient temperature. Combinatorial photovoltaic device libraries with Al/ZnO/In2S3/Cu2ZnSnS4/Mo/SiO2 structure were built at optimal processing conditions to investigate the feasibility of the sputtered In2S3 buffer layers and of an accelerated optimization of the device structure. The performance of the resulting In2S3/Cu2ZnSnS4 photovoltaic devices is on par with CdS/Cu2ZnSnS4 reference solar cells with similar values for short circuit currents and open circuit voltages, despite the overall quite low efficiency of the devices (-2%). Overall, these results demonstrate how a high-throughput experimental approach can be used to accelerate the development of contact materials and facilitate the optimization of thin film solar cell devices.

14 SOLAR ENERGY↗

Increased photoluminescence of strain-reduced, high-Sn composition Ge{sub 1-x}Sn{sub x} alloys grown by molecular beam epitaxy

We synthesized up to Ge{sub 0.914}Sn{sub 0.086} alloys on (100) GaAs/In{sub y}Ga{sub 1-y}As buffer layers using molecular beam epitaxy. The buffer layers enable engineered control of strain in the Ge{sub 1-x}Sn{sub x} layers to reduce strain-related defects and precipitation. Samples grown under similar conditions show a monotonic increase in the integrated photoluminescence (PL) intensity as the Sn composition is increased, indicating changes in the bandstructure favorable for optoelectronics. We account for bandgap changes from strain and composition to determine a direct bandgap bowing parameter of b = 2.1 {+-} 0.1. According to our models, these are the first Ge{sub 1-x}Sn{sub x} samples that are both direct-bandgap and exhibit PL.

36 MATERIALS SCIENCE↗