Search NASA⌕ Search

SEARCH · Search NASA

Results for “buoy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Aircraft measurement of sea surface temperature during the West Coast Experiment

During the West Coast Experiment in March 1977, a test was conducted to ascertain the effectiveness of using remote sensing techniques to estimate sea surface temperature (SST) from infrared (IR) emissions of the sea surface. Aircraft flights were made over three buoys moored in southern California coastal waters, and data was collected of sea surface emissions at thermal IR wavelengths (7.95-13.5 micrometers). SST obtained from the remote sensing measurements were compared with in situ SST measured with thermistors mounted on the buoys. The remotely determined SST were from 1.4-2.9 C lower than the in situ measurements. Several factors are discussed that could account for the differences.

Schieldge, J. P.↗

Remote sensing of the ocean waveheight spectrum using synthetic-aperture-radar images

The paper discusses problems in the detection and measurement of ocean waves from their SAR images, in particular the measurement of the wavenumber spectrum of ocean-wave-height fluctuations. Comparisons on a limited set of pitch-roll buoy and SEASAT SAR measurements during the 1978 JASIN experiment reveal that degradation of SAR resolution caused by wave orbital motion is a crucial factor in the detection of waves by SAR images. Thus, waves with small slopes traveling perpendicular to the SAR flight path are more easily detected than waves with large slopes traveling along the flight path. Although the SAR estimates in this comparison were found to contain significant biases, they were in rough agreement with buoy measurements, provided the ocean wavelength was between about 120 and 400 m and the ocean wave direction was not approximately along the SAR flight path.

Vesecky, J. F.↗

The measurement of the synoptic scale wind over the ocean

Mesoscale and microscale features of the turbulent winds over the ocean are related to the synoptic scale winds in terms of published spectral forms for the microscale, a mesoscale valley and published values of U*, VAR u', VAR v' and z/L, as defined in the text and as obtained for moderate to gale force winds. The frequencies involved correspond to periods longer than 1 hour and extend to the microscale, which starts at a period near 2 minutes, or so, and continues to the Kolmogorov inertial range. Nondimensional spectra that span both the mesoscale and the microscale are derived as a function of u, f(= n z/u) and z/L, where z is 10 meters, L is the Monin Obukov stability length and u is evaluated at 10 meters. For the same u, different values of z/L produce a range of values of u which in turn result in variations of the eddy structure of the mesoscale and microscale spectra. Both conventional anemometer averages and remotely sensed winds contain a random component of the mesoscale wind in their values. These components are differnces and not errors when winds are compared, and quantitative values for these differences are given. Ways to improve the measurement of the synoptic scale wind by transient ships, data buoys and scatterometers on future spacecraft are described. These ways are loner averaging times for ships and data buoys, depending on the synoptic conditions, and pooling spacecraft to form super observations. Design considerations for future remote sensing systems are given.

Pierson, W. J.↗

The movement and decay of ice edge bands in the winter Bering Sea

A study of the movement and decay of ice bands in the Bering Sea carried out in March 1981 is described. A pair of radio transponders mounted on ice floes within a band was tracked and the band motion was compared with that of a satellite-tracked buoy deployed in the ice interior. The results show that the bands moved away from the interior pack ice at a speed 30 percent greater than that of the interior ice, that the cause of this band acceleration was very likely the wind-wave radiation stress on the upwind side of the band, and that as the bands moved into warmer water, they decayed both by wind-wave erosion of the upwind edge and by bottom melting. The working of the buoys and the method of deployment are described, as are the band shape, trajectory, and decay. By a calculation of the steady state stress balance on the band, it is shown that the radiation stress can account for the velocity increase of the band relative to the ice interior.

Martin, S.↗

Mechanisms for SAR imaging of ocean surface phenomena: Theory and experiment

Understanding the SAR response to surface wave is a central issue in the analysis of SAR ocean images. The imaging mechanism for gravity waves and the practical question of just which characteristics of the ocean wave field can be measured remotely using SAR were examined. Assessments of wave imaging theory are based primarily on comparisons of the directional wave height variance spectrum psi (K) measured by in situ buoys with estimates from SAR images. Other criteria are also recommended, e.g., the effects of focus adjustments. It is assumed that fluctuations in SAR image intensity are proportional to fluctuations in ocean surface height. If this were true, the Fourier power spectrum of a SAR image and corresponding surface measurements of psi would coincide. Differences between SAR estimates based on this hypothesis and buoy measurements of psi are then used to begin the assessment of rival wave imaging theories.

Vesecky, J. F.↗

Method of measuring sea surface water temperature with a satellite including wideband passive synthetic-aperture multichannel receiver

A wideband passive synthetic-aperture multichannel receiver with an antenna is mounted on a satellite which travels in an orbit above the Earth passing over large bodies of water, e.g., the Atlantic Ocean. The antenna is scanned to receive signals over a wide frequency band from each incremental surface area (pixel) of the water which are related to the pixel's sea temperature. The received signals are fed to several channels which are tuned to separate selected frequencies. Their outputs are fed to a processor with a memory for storage. As the antenna points to pixels within a calibration area around a buoy of known coordinates, signals are likewise received and stored. Exactly measured sea temperature is received from the buoy. After passing over several calibration areas, a forward stepwise regression analysis is performed to produce an expression which selects the significant from the insignificant channels and assigns weights (coefficients) to them. The expression is used to determine the sea temperature at each pixel based on the signals received therefrom. Wind temperature, pressure, and wind speed at each pixel can also be calculated.

Stacey, J. M.↗

A comparison of in situ and airborne radar observations of ocean wave directionality

The directional spectrum of a fully arisen, about 3 m sea as measured by an experimental airborne radar, the NASA K(u)-band radar ocean wave spectrometer (ROWS), is compared to reference pitch-roll buoy data and to the classical SWOP (stereo wave observations project) spectrum for fully developed conditions. The ROWS spectrum, inferred indirectly from backscattered power measurements at 5-km altitude, is shown to be in excellent agreement with the buoy spectrum. Specifically, excellent agreement is found between the two nondirectional height spectra, and mean wave directions and directional spreads as functions of frequency. A comparison of the ROWS and SWOP spectra shows the two spectra to be very similar, in detailed shape as well as in terms of the gross spreading characteristics. Both spectra are seen to exhibit bimodal structures which accord with the Phillips' (1958) resonance mechanism. This observation is thus seen to support Phillips' contention that the SWOP modes were indeed resonance modes, not statistical artifacts.

Jackson, F. C.↗

The impact of the FGGE observing systems in the Southern Hemisphere

Results of studies carried out at the Australian Numerical Meteorology Research Centre (ANMRC) and the Australian Bureau of Meteorology to assess the impact of FGGE on numerical weather prediction in the Southern Hemisphere are presented. These studies inducate that the FGGE data base had a significant impact on analysis and numerical weather prediction. From the operational standpoint, the most outstanding contribution was made by the drifting buoy data that enabled reliable routine surface pressure analyses to be made over the entire hemisphere. The results of a limited study using the MNMRC data assimilation scheme show that the quality of prediction to 48 hours hinges crucially on both the buoy pressure data and satellite temperature soundings with single level satellite winds having a small impact.

Puri, K.↗

Sea surface temperature - Observations from geostationary satellites

Multispectral image data acquired from the VISSR atmospheric sounder (VAS) on the geostationary GOES satellites were used to estimate sea surface temperatures (SST). A procedure was developed to screen VAS visible and infrared data for cloud-free regions for estimation of SST from the clear infrared radiances. A data set of matches between the VAS radiances and high quality buoy estimates of SST was produced. A linear regression analysis of these matches was performed to generate an empirical algorithm relating the VAS window channel brightness temperatures to the estimates of SST recorded by NOAA fixed environment buoys. Daily maps of SST during Hurricanes Alicia (1983) and Debbie (1982) demonstrated the ability of VAS to monitor air-sea interactions at high temporal and spatial scales.

Bates, J. J.↗

Ocean Drifter Project

Four drifting buoys were fabricated from mostly local hardware plus animal locating transmitters. The first two working models were dropped from a Wallops aircraft, to test the mechanical integrity and to test the ability of the whole system to withstand the drop and provide usable data. There are two temperature sensors on board, one to measure sea surface temperature and the other to measure air temperature. An onboard computer controls the transmissions, sending three water temperature readings for each air temperature reading in order to differentiate one from the other after data reduction. Guidelines for the development and test of optical drifting buoys include: air deployable and expendable, reasonable cost for multiple deployment, 1 year lifetime, use of existing technology and a minimal validation parameter set.

Mason, C. D.↗

Examples of, reasons for, and consequences of the poor quality of wind data from ships for the marine boundary layer - Implications for remote sensing

Wind reports by data buoys are used to demonstrate that these reports have in the past provided useful values for the synoptic scale winds and that at present these reports provide very reliable value for the synoptic scale winds. Past studies of wind reports by ships have revealed that the data are of poor quality, but the causes for this poor quality are not identified. Examples of the poor quality of wind data from ships are obtained by comparing ship reports with buoy reports and comparing reports of different kinds of ships with each other. These comparisons identify many different reasons for the poor quality of wind data from ships. Suggestions are made for improving the quality of ship data. The consequences of the poor quality of ship winds are described in terms of the effects on weather and wave forecasts. The implications for remotely sensed winds are discussed.

Pierson, Willard J., Jr.↗

Wave evolution in the marginal ice zone - Model predictions and comparisons with on-site and remote data

The ocean-wave dispersion relation and viscous attenuation by a sea ice cover were studied for waves in the marginal ice zone (MIZ). The Labrador ice margin experiment (Limex), conducted off the east coast of Newfoundland, Canada in March 1987, provided aircraft SAR, wave buoy, and ice property data. Based on the wave number spectrum from SAR data, the concurrent wave frequency spectrum from ocean buoy data, and accelerometer data on the ice during Limex '87, the dispersion relation has been derived and compared with the model. Accelerometers were deployed at the ice edge and into the ice pack. Data from the accelerometers were used to estimate wave energy attenuation rates and compared with the model. The model-data comparisons are reasonably good for the ice conditions observed during Limex' 87.

Liu, A. K.↗

Errors of five-day mean surface wind and temperature conditions due to inadequate sampling

Surface meteorological reports of wind components, wind speed, air temperature, and sea-surface temperature from buoys located in equatorial and midlatitude regions are used in a simulation of random sampling to determine errors of the calculated means due to inadequate sampling. Subsampling the data with several different sample sizes leads to estimates of the accuracy of the subsampled means. The number N of random observations needed to compute mean winds with chosen accuracies of 0.5 (N sub 0.5) and 1.0 (N sub 1,0) m/s and mean air and sea surface temperatures with chosen accuracies of 0.1 (N sub 0.1) and 0.2 (N sub 0.2) C were calculated for each 5-day and 30-day period in the buoy datasets. Mean values of N for the various accuracies and datasets are given. A second-order polynomial relation is established between N and the variability of the data record. This relationship demonstrates that for the same accuracy, N increases as the variability of the data record increases. The relationship is also independent of the data source. Volunteer-observing ship data do not satisfy the recommended minimum number of observations for obtaining 0.5 m/s and 0.2 C accuracy for most locations. The effect of having remotely sensed data is discussed.

Legler, David M.↗

Near-nadir microwave specular returns from the sea surface - Altimeter algorithms for wind and wind stress

Two approaches have been adopted to construct altimeter wind algorithms: one is based on the mean-square sea surface slope, and the other is based on the Seasat scatterometer wind. Both types of algorithms are critically reviewed with respect to the mechanism governing near-nadir sea returns and the comparison between altimeter and buoy winds. A new algorithm is proposed; it is deduced on the basis of microwave specular reflection and is finely tuned with buoy-measured winds. On the basis of this algorithm and the formula of the wind-stress coefficient, a simple wind-stress algorithm is also proposed.

Wu, Jin↗

Accurate GPS measurement of the location and orientation of a floating platform

This article describes the design and initial tests of the GPS portion of a system for making seafloor geodesy measurements. In the planned system, GPS antennas on a floating platform will be used to measure the location of an acoustic transducer, attached below the platform, which interrogates an array of transponders on the seafloor. Since the GPS antennas are necessarily some distance above the transducer, a short-baseline GPS interferometer consisting of three antennas is used to measure the platform's orientation. A preliminary test of several crucial elements of the system was performed. The test involved a fixed antenna on the pier and a second antenna floating on a buoy about 80 m away. GPS measurements of the vertical component of this baseline, analyzed independently by two groups using different software, agree with each other and with an independent measurement within a centimeter. The first test of an integrated GPS/acoustic system took place in the Santa Cruz Basin off the coast of southern California in May 1990. In this test a much larger buoy, designed and built at SIO, was equipped with three GPS antennas and an acoustic transducer that interrogated a transponder on the ocean floor. Preliminary analysis indicates that the horizontal position of the transponder can be determined with a precision of about a centimeter.

Purcell, G. H., Jr.↗

Reference level winds from balloon platforms

The superpressure balloon was developed to provide a method of obtaining global winds at all altitudes from 5 to 30 km. If a balloon could be made to fly for several weeks at a constant altitude, and if it could be tracked accurately on its global circuits, the balloon would provide a tag for the air parcel in which it was embedded. The Lagrangian data on the atmospheric circulation would provide a superior data input to the numerical model. The Global Atmospheric Research Program (GARP) was initiated in large part based on the promise of this technique coupled with free-floating ocean buoys and satellite radiometers. The initial name proposed by Charney for GARP was SABABURA 'SAtellite BAlloon BUoy RAdiometric system' (Charney, 1966). However, although the superpressure balloon exceeded its designers' expectations for flight duration in the stratosphere (longest flight duration of 744 days), flight duration below 10 km was limited by icing in super-cooled clouds to a few days. The balloon was relegated to a secondary role during the GARP Special Observing Periods. The several major superpressure balloon programs for global wind measurement are described as well as those new developments which make the balloon once again an attractive vehicle for measurement of global winds as a reference and bench-mark system for future satellite systems.

Lally, Vincent E.↗

Optical Rain Gauge Performance: Second Workshop on Optical Rain Gauge Measurements

The primary focus of the workshop was on the performance and reliability of STi mini-Optical Rain Gauges in a number of environments, including deployments on ships and buoys in the western equatorial Pacific Ocean during the TOGA/COARE field experiment, deployments on buoys in U.S. coastal waters, and comparisons with other types of rain gauges on the Virginia coast and in Florida. The workshop was attended by 20 investigators, representing 10 different institutions, who gathered to present new results obtained since the first workshop (April 1993), to discuss problems, to consider solutions, and to chart future directions. Post-TOGA/COARE calibration studies were also presented.

Short, David A.↗

Correcting infrared satellite estimates of sea surface temperature for atmospheric water vapor attenuation

A new satellite sea surface temperature (SST) algorithm is developed that uses nearly coincident measurements from the microwave special sensor microwave imager (SSM/I) to correct for atmospheric moisture attenuation of the infrared signal from the advanced very high resolution radiometer (AVHRR). This new SST algorithm is applied to AVHRR imagery from the South Pacific and Norwegian seas, which are then compared with simultaneous in situ (ship based) measurements of both skin and bulk SST. In addition, an SST algorithm using a quadratic product of the difference between the two AVHRR thermal infrared channels is compared with the in situ measurements. While the quadratic formulation provides a considerable improvement over the older cross product (CPSST) and multichannel (MCSST) algorithms, the SSM/I corrected SST (called the water vapor or WVSST) shows overall smaller errors when compared to both the skin and bulk in situ SST observations. Applied to individual AVHRR images, the WVSST reveals an SST difference pattern (CPSST-WVSST) similar in shape to the water vapor structure while the CPSST-quadratic SST difference appears unrelated in pattern to the nearly coincident water vapor pattern. An application of the WVSST to week-long composites of global area coverage (GAC) AVHRR data demonstrates again the manner in which the WVSST corrects the AVHRR for atmospheric moisture attenuation. By comparison the quadratic SST method underestimates the SST corrections in the lower latitudes and overestimates the SST in th e higher latitudes. Correlations between the AVHRR thermal channel differences and the SSM/I water vapor demonstrate the inability of the channel difference to represent water vapor in the midlatitude and high latitudes during summer. Compared against drifting buoy data the WVSST and the quadratic SST both exhibit the same general behavior with the relatively small differences with the buoy temperatures.

Emery, William J.↗