Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic matrix composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Spatially Resolved Raman Spectroscopy of Thin Carbon Interphase in SiC Ceramic Matrix Composites

A dedicated analysis method is presented to extract the Raman spectrum of an interphase layer thinner than the laser spot size. We focused on spatial correlations between the contrast of optical micrographs and Raman hyperspectral data to predict the constituents of the mixed spectra measured near the interphase. By employing a mapping step size of 0.1 μm, the Raman spectrum of approximately 0.3-μm-thick carbon interphase in a SiC fiber-reinforced SiC matrix composite was extracted from data acquired with a theoretical spot size of about 0.7 μm. Notably, conventional chemometrics procedures were unable to isolate the interphase signal, instead producing a spectrum representing a mixture of interphase and matrix. This study used another composite with approximately 0.9-μm-thick interphase to validate the analysis method, enabling direct measurement of the interphase spectrum. The proposed Raman analysis method has advantages in specimen volume and turnaround time compared to traditional characterization methods, such as transmission electron microscopy. In conclusion, this study also evaluates the applicability of the analysis method to different composite materials and identifies key requirements of the measurements, including the ratio of interphase thickness to spot size and the homogeneity of the surrounding matrix.

ceramic matrix composite↗
NASA NTRSDate not supplied

Ceramic Matrix Composite (CMC) Thermal Protection Systems (TPS) and Hot Structures for Hypersonic Vehicles

Thermal protection systems (TPS) and hot structures are required for a range of hypersonic vehicles ranging from ballistic reentry to hypersonic cruise vehicles, both within Earth’s atmosphere and non-Earth atmospheres. This includes single-stage to orbit (SSTO), two-stage to orbit (TSTO) accelerators, access to space vehicles, and hypersonic cruise vehicles. This presentation will start out with a brief discussion of aerodynamic heating and thermal management techniques to address the high heating. The argument is presented that as we move from rocket-based vehicles to air-breathing vehicles, we need to move away from the “insulated airplane” approach used on the Space Shuttle Orbiter to a wide range of TPS and hot structure approaches. The primary portion of the paper will discuss issues and design options for CMC TPS and hot structure components. The two primary technical challenges impacting the use of CMC TPS and hot structures for hypersonic vehicles are environmental durability and fabrication, and will be discussed briefly.

ceramic matrix composites↗
NASA NTRS2015

Oxide_Oxide Ceramic Matrix Composite (CMC) Exhaust Mixer Development in the NASA Environmentally Responsible Aviation (ERA) Project

Rolls-Royce North American Technologies, Inc. (LibertyWorksLW) began considering the development of CMC exhaust forced mixers in 2008, as a means of obtaining reduced weight and hotter operating temperature capability, while minimizing shape distortion during operation, which would improve mixing efficiency and reduce fuel burn. Increased component durability, enhanced ability to fabricate complex-shaped components, and engine noise reduction are other potential advantages of CMC mixers (compared to metallic mixers). In 2010, NASA was pursuing the reduction of NOx emissions, fuel burn, and noise from turbine engines in Phase I of the Environmentally Responsible Aviation (ERA) Project. ERA subtasks, including those focused on CMC components, were formulated with the goal of maturing technology from proof of concept validation (TRL 3) to a systemsubsystem or prototype demonstration in a relevant environment (TRL 6). In April 2010, the NASA Glenn Research Center (GRC) and LibertyWorks jointly initiated a CMC Exhaust System Validation Program within the ERA Project, teaming on CMC exhaust mixer development for subsonic jet engines capable of operating with increased performance. Our initial focus was on designing, fabricating, and characterizing the thrust and acoustic performance of a roughly quarter-scale 16-lobe oxide oxide CMC mixer and tail cone along with a conventional low bypass exhaust nozzle. Support Services, LLC (Allendale, MI) and ATK COI Ceramics, Inc. (COIC, in San Diego, CA) supported the design of a subscale nozzle assembly that consisted of an oxide oxide CMC mixer and center body, with each component mounted on a metallic attachment ring. That design was based upon the operating conditions a mixer would experience in a turbofan engine. Validation of the aerodynamic and acoustic performance of the subscale mixer via testing and the achievement of TRL 4 encouraged the NASALWCOIC team to move to the next phase where a full scale CMC mixer sized for a RR AE3007 engine and a compatible attachment flange were designed, followed by CMC component fabrication by COIC, and vibration testing at GRC under conditions simulating the structural and dynamic environment encountered during engine operation. AFRL (WPAFB) supported this testing by performing 3D laser vibrometry to identify the mixer mode shapes and modal frequencies. The successful fabrication and testing of such a component has been achieved. The CMC mixer demonstrated good durability during vibration testing at room and elevated temperature (TRL5). This has cleared the article for a ground-based test on a Rolls-Royce AE3007 engine, where the performance and benefits of the component can be further assessed.

exhaust nozzles↗
NASA NTRS2022

Vacuum Melt Infiltration of 2D Tyranno SA3® Ceramic Matrix Composites with Cr-25(wt.%)Si Intermetallic Alloy

The potential and limitations of vacuum melt infiltrating woven preforms of 2D Tyranno SA3 fibers with Cr-25(wt.%)Si alloy were investigated. Microstructural observations revealed that the volume fractions of open voids infiltrated by the molten metal varied between 3.7 and 10.0% irrespective of the magnitudes of the melt infiltration temperatures and hold times, which was attributed in part to substantial volatilization of the silicide charge based on computational thermodynamics. In the absence of experimental data, poor wettability of the melt could not be ruled out unambiguously. Other possible reasons are carefully examined and discarded. Ring microstructures were observed around the fibers mainly at the outer surfaces of the infiltrated preform, where the BN and chemical vapor infiltrated SiC coatings had vaporized in the high vacuum environment. In contrast, they were absent in the interior of the preform, where the coatings were still present with no evidence of molten metal attack of the coatings. Details of thermodynamic calculations are presented to confirm the volatilization of the BN and CVI SiC coatings thereby resulting in the ring microstructures due to the filling of voids by the molten silicide. It is concluded that successful melt infiltration of Tyranno SA3® with Cr-25%Si can be only achieved under sufficient positive pressure to prevent volatilization of the coatings and the molten silicide.

Cr-25%Si↗
NASA NTRS2016

Overview of CMC (Ceramic Matrix Composite) Research at the NASA Glenn Research Center

In support of NASAs Aeronautics Research Mission, the Glenn Research Center has developed and assessed various constituents for a high temperature (2700F) SiCSiC CMC system for turbine engine applications. Combinations of highly creep-resistant SiC fibers, advanced 3D weaves, durable environmental barrier coatings (EBCs), and a 2700F-capable hybrid SiC matrix are being developed evaluated. The resulting improvements in CMC mechanical properties and durability will be summarized. The development and validation of models for predicting the effects of the environment on the durability of CMCs and EBCs and other operating-environment challenges including the effect of CMAS (calcium magnesium aluminosilicate) degradation of EBCs will be discussed. Progress toward the development of CMC joining technology for 2400F joint applications will also be reviewed.

Ceramic Matrix Composites↗
NASA NTRS2021

Melt Infiltration Studies of 2D Tyranno SA3(R) Ceramic Matrix Composite Preforms with CrSi2 Intermetallic Alloy

The present paper reports the results of melt infiltrating 2D Tyranno SA3@ fiber woven preforms with molten CrSi2 between 1768 and 1896 K under a vacuum of 1.3 x 10-4 Pa (10-6 torr). The infiltration times varied between 1800 and 7200 s, which did not have any significant effect on the volume fraction of voids filled with the metal. Optical and scanning electron microscopy, back scattered electron imaging, energy dispersion spectroscopy and Raman spectroscopy were used to characterize the infiltrated preforms. A plot of the volume fraction of open voids infiltrated against the absolute melt infiltration temperature showed a sharp peak at 1773 K with almost complete infiltration of the voids at this temperature. The extent of silicide infiltration of the preforms dropped steeply above 1773 K with increasing melt infiltration temperature irrespective of the amount of infiltration time. Above 1805 K, the volume fraction of voids infiltrated with the melt was nearly 0%. It is demonstrated that CrSi2 did not show evidence of a reaction with the SiC fibers. The possibility that a resisting force due to contact angle hysteresis (CAH) may have influenced the diminishing amount of voids filled with increasing temperature above 1773 K was examined. The resistance force was estimated to be extremely small to be consequential. Another possibility that the CrSi2 may have decomposed into Cr(g) and Si(g) in the vacuum melt infiltration furnace appeared to be more plausible based on thermodynamic analyses. An empirical equation is proposed to calculate the amount of remaining charge left to infiltrate the preforms at the infiltration temperature. It is shown that an initial charge of 10 g would rationalize the present observations. While the decomposition of the CrSi2 appeared to mostly explain the present results, some discrepancies were observed, which were inconsistent with the decomposition model.

CrSi2, chromium silicide, ceramic matrix composite↗
DOE OSTI2024

Development of Additive Manufacturing for Ceramic Matrix Composite Vanes

This report discusses the development of additive manufacturing for polymer-derived ceramic materials to create novel cooled gas turbine airfoils made from ceramics. Gas turbine engines have extremely high temperatures in the hot section of the engine that exceed the melting point of nickel superalloy materials that the engine is made from. Advanced cooling technologies have been developed over decades for metallic parts. Ceramic materials have higher temperature capabilities than superalloys, but are difficult to shape in the complex designs used in modern turbines. Several thrusts were investigated during the project, including development of higher material strength resins, improvement of ultraviolet (UV) photopolymerization and post-processing techniques to increase survivability of ceramic parts, thermomechanical modeling of novel ceramic airfoil designs for higher cooling effectiveness, and experimental validation of the modeling and manufacturing in a turbine vane test facility at nondimensional conditions that are relevant to modern gas turbines. Some major findings of the work include a significant increase in ceramic survivability during pyrolysis (a high temperature process that converts the organic material to a ceramic) by adjusting the composition ratios of the resins, as well as a tolulene soak after printing to remove unreacted polymer material. Thermomechanical optimization of the internal cooling structure indicated that a high density pin fin array would enable an 80% increase in overall cooling effectiveness relative to a baseline geometry, which was later verified during experimental testing in a high speed linear cascade. Ceramic vanes were tested at Mach numbers of up to 0.9 which is relevant to modern gas turbines. High temperature capability of the ceramic vanes was not tested in this work.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Ultimate Tensile Strength as a Function of Test Rate for Various Ceramic Matrix Composites at Elevated Temperatures

Ultimate tensile strength of five different continuous fiber-reinforced ceramic composites, including SiC/BSAS (2D 2 types), SiC/MAS-5 (2D), SiC/SiC (2D enhanced), and C/SiC(2D) was determined as a function of test rate at I 100 to 1200 'C in air. All five composite materials exhibited a significant dependency of ultimate strength on test rate such that the ultimate strength decreased with decreasing test rate, similar to the behavior observed in many advanced monolithic ceramics at elevated temperatures. The application of the preloading technique as well as the prediction of life from one loading configuration (constant stress rate) to another (constant stress loading) for SiC/BSAS suggested that the overall macroscopic failure mechanism of the composites would be the one governed by a power-law type of damage evolution/accumulation, analogous to slow crack growth commonly observed in advanced monolithic ceramics.

Choi, Sung R.↗
NASA NTRS1991

Effects of aeroconvective environments on 2D reinforced ceramic matrix composites

The effect of aeroconvective heating environment similar to that observed a spacecraft ascent or reentry from orbit, on the performance of a commercial carbon-reinforced ceramic matrix material specimens of two configurations (orthotropic and quasi-isotropic), fabricated by the Societe Europenne Propulsion (SEP) process was investigated using the NASA Ames Research Center 20 Megawatt Panel Test facility. The performance of the commercial material was compared with the SEP prepared materials. It was found that, whereas the quasi-isotropic SEP specimens exhibited a much higher mass loss rate and a significant dimensional change upon exposure to the thermal environment than did the orthotropic ones, the commercial SEP-like materials did not exhibit these characteristics. There was no greater mass loss rate for the quasi-isotropic specimens, and no dimension changes were observed. The Nicalon reinforced materials in both configurations, as fabricated by SEP or by the commercial source, showed no mass changes and no dimensional changes.

Riccitiello, Salvatore R.↗
NASA NTRS1993

Acousto-Ultrasonic analysis of failure in ceramic matrix composite tensile specimens

Three types of acousto-ultrasonic (AU) measurements, stress-wave factor (SWF), lowest antisymmetric plate mode group velocity (VS), and lowest symmetric plate mode group velocity (VL), were performed on specimens before and after tensile failure. Three different Nicalon fiber architectures with ceramic matrices were tested. These composites were categorized as 1D (unidirectional fiber orientation) SiC/CAS glass ceramic, and 2D and 3D woven SiC/SiC ceramic matrix materials. SWF was found to be degraded after tensile failure in all three material categories. VS was found to be degraded only in the 1D SiC/CAS. VL was difficult to determine on the irregular specimen surfaces but appeared unchanged on all failed specimens. 3D woven specimens with heat-treatment at high temperature exhibited degradation only in SWF.

Kautz, Harold E.↗
NASA NTRS2001

Ceramic Matrix Composite (CMC) Materials Characterization

Under the former NASA EPM Program, much initial progress was made in identifying constituent materials and processes for SiC/SiC ceramic composite hot-section components. This presentation discusses the performance benefits of these approaches and elaborates on further constituent and property improvements made under NASA UEET. These include specific treatments at NASA that significantly improve the creep and environmental resistance of the Sylramic(TM) SiC fiber as well as the thermal conductivity and creep resistance of the CVI Sic matrix. Also discussed are recent findings concerning the beneficial effects of certain 2D-fabric architectures and carbon between the BN interphase coating and Sic matrix.

Calomino, Anthony↗
NASA NTRS2001

Ceramic Matrix Composite (CMC) Materials Development

Under the former NASA EPM Program, much initial progress was made in identifying constituent materials and processes for SiC/SiC ceramic composite hot-section components. This presentation discusses the performance benefits of these approaches and elaborates on further constituent and property improvements made under NASA UEET. These include specific treatments at NASA that significantly improve the creep and environmental resistance of the Sylramic(TM) Sic fiber as well as the thermal conductivity and creep resistance of the CVI Sic matrix. Also discussed are recent findings concerning the beneficial effects of certain 2D-fabric architectures and carbon between the BN interphase coating and Sic matrix.

DiCarlo, James↗
NASA NTRS1996

High Temperature Mechanical Behavior of Ceramic Matrix Composites

The research accomplishments under this grant were very extensive in the areas of the high temperature behavior of ceramics, ceramic composites and testing standards for these materials. Rather than try to summarize all this research I have enclosed research papers and reports which were completed with the funding provided by the grant.

Hemann, John↗
NASA NTRS1995

Creep of Refractory Fibers and Modeling of Metal and Ceramic Matrix Composite Creep Behavior

Our concentration during this research was on the following subprograms. (1) Ultra high vacuum creep tests on 218, ST300 and WHfC tungsten and MoHfC molybdenum alloy wires, temperature range from 1100 K to 1500 K, creep time of 1 to 500 hours. (2) High temperature vacuum tensile tests on 218, ST300 and WHfC tungsten and MoHfC molybdenum alloy wires. (3) Air and vacuum tensile creep tests on polycrystalline and single crystal alumina fibers, such as alumina-mullite Nextel fiber, yttrium aluminum ganet (YAG) and Saphikon, temperature range from 1150 K to 1470 K, creep time of 2 to 200 hours. (4) Microstructural evaluation of crept fibers, TEM study on the crept metal wires, SEM study on the fracture surface of ceramic fibers. (5) Metal Matrix Composite creep models, based on the fiber creep properties and fiber-matrix interface zone formation.

Tewari, S.N.↗
NASA NTRS1999

Sensor Lead Wires Positioned on SiC-based Monolithic Ceramic and Fiber- reinforced Ceramic Matrix Composite Subcomponents with Flat and Curved Surfaces

There is strong interest in the development of silicon carbide-based monolithic ceramic and composite materials and components for demanding, high-temperature applications. Thorough characterization of material properties, including high-temperature testing under simulated or actual operating conditions, is a high priority for programs involved in developing these silicon carbide- (SiC) based materials and components. Members of the Sensors and Electronics Technology Branch at the NASA Lewis Research Center are developing minimally intrusive methods of measuring the properties (such as the surface temperature, strain, and heat flux characteristics) of components and subelements that are being tested or operated in hostile, high-temperature environments. Their primary goal is to instrument the test article or operating component with durable sensors that have a minimal effect on test conditions such as the gas flow across the surface of the item and the material response (including the through-thickness conduction of heat). Therefore, the main thrust of their work has been the development of thin-film sensors (e.g., thermocouples or strain gauges) for use on various advanced material test articles, including SiC/SiC composite components. There was a need for a better method of securing sensor lead wires on SiC-based components and subelements that would be tested at temperatures to 1000 C (or higher), to enhance the durability of the overall minimally intrusive sensor system. To address this need, Lewis researchers devised an alternative approach for positioning the sensor lead wires (which are connected to the thin-film sensors) on SiC or SiC/SiC components. A reaction-forming method of joining was used to strongly bond hoop-shaped monolithic SiC and SiC/SiC composite attachments of various sizes to both flat and curved surfaces of SiC/SiC composite subelements (see the photos). This approach is based on an affordable, robust ceramic joining technology, named ARCJoinT, which was developed at Lewis for the joining of SiC-based ceramics and fiber-reinforced composites.

Kiser, James D.↗
NASA NTRS2003

Probabilistic Evaluation of Advanced Ceramic Matrix Composite Structures

The objective of this report is to summarize the deterministic and probabilistic structural evaluation results of two structures made with advanced ceramic composites (CMC): internally pressurized tube and uniformly loaded flange. The deterministic structural evaluation includes stress, displacement, and buckling analyses. It is carried out using the finite element code MHOST, developed for the 3-D inelastic analysis of structures that are made with advanced materials. The probabilistic evaluation is performed using the integrated probabilistic assessment of composite structures computer code IPACS. The affects of uncertainties in primitive variables related to the material, fabrication process, and loadings on the material property and structural response behavior are quantified. The primitive variables considered are: thermo-mechanical properties of fiber and matrix, fiber and void volume ratios, use temperature, and pressure. The probabilistic structural analysis and probabilistic strength results are used by IPACS to perform reliability and risk evaluation of the two structures. The results will show that the sensitivity information obtained for the two composite structures from the computational simulation can be used to alter the design process to meet desired service requirements. In addition to detailed probabilistic analysis of the two structures, the following were performed specifically on the CMC tube: (1) predicted the failure load and the buckling load, (2) performed coupled non-deterministic multi-disciplinary structural analysis, and (3) demonstrated that probabilistic sensitivities can be used to select a reduced set of design variables for optimization.

Abumeri, Galib H.↗
NASA NTRS2007

Improving Turbine Performance with Ceramic Matrix Composites

Under the new NASA Fundamental Aeronautics Program, efforts are on-going within the Supersonics Project aimed at the implementation of advanced SiC/SiC ceramic composites into hot section components of future gas turbine engines. Due to recent NASA advancements in SiC-based fibers and matrices, these composites are lighter and capable of much higher service temperatures than current metallic superalloys, which in turn will allow the engines to operate at higher efficiencies and reduced emissions. This presentation briefly reviews studies within Task 6.3.3 that are primarily aimed at developing physics-based concepts, tools, and process/property models for micro- and macro-structural design, fabrication, and lifing of SiC/SiC turbine components in general and airfoils in particular. Particular emphasis is currently being placed on understanding and modeling (1) creep effects on residual stress development within the component, (2) fiber architecture effects on key composite properties such as design strength, and (3) preform formation processes so that the optimum architectures can be implemented into complex-shaped components, such as turbine vanes and blades.

DiCarlo, James A.↗