Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Behavior of Aging, Micro-Void, and Self-Healing of Glass/Ceramic Materials and Its Effect on Mechanical Properties

This chapter first describes tests to investigate the temporal evolution of the volume fraction of ceramic phases, the evolution of micro-damage, and the self-healing behavior of the glass ceramic sealant used in SOFCs, then a phenomenological model based on mechanical analogs is developed to describe the temperature dependent Young’s modulus of glass ceramic seal materials. It was found that after the initial sintering process, further crystallization of the glass ceramic sealant does not stop, but slows down and reduces the residual glass content while boosting the ceramic crystalline content. Under the long-term operating environment, distinct fibrous and needle-like crystals in the amorphous phase disappeared, and smeared/diffused phase boundaries between the glass phase and ceramic phase were observed. Meanwhile, the micro-damage was induced by the cooling-down process from the operating temperature to the room temperature, which can potentially degrade the mechanical properties of the glass/ceramic sealant. The glass/ceramic sealant self-healed upon reheating to the SOFC operating temperature, which can restore the mechanical performance of the glass/ceramic sealant. The phenomenological model developed here includes the effects of continuing aging and devitrification on the ceramic phase volume fraction and the resulted mechanical properties of glass ceramic seal material are considered. The effects of micro-voids and self-healing are also considered using a continuum damage mechanics (CDM) model. The formulation is for glass/ceramic seal in general, and it can be further developed to account for effects of various processing parameters. This model was applied to G18, and the temperature-dependent experimental measurements were used to calibrate the modeling parameters and to validate the model prediction.

aging↗

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Ceramic Waste Form Data Package

The purpose of this data package is to provide information about simulated crystalline waste forms that can be used to select an appropriate composition for a Cold Crucible Induction Melter (CCIM) proof of principle demonstration. Melt processing, viscosity, electrical conductivity, and thermal analysis information was collected to assess the ability of two potential candidate ceramic compositions to be processed in the Idaho National Laboratory (INL) CCIM and to guide processing parameters for the CCIM operation. Given uncertainties in the CCIM capabilities to reach certain temperatures throughout the system, one waste form designated 'Fe-MP' was designed towards enabling processing and another, designated 'CAF-5%TM-MP' was designed towards optimized microstructure. Melt processing studies confirmed both compositions could be poured from a crucible at 1600°C although the CAF-5%TM-MP composition froze before pouring was complete due to rapid crystallization (upon cooling). X-ray diffraction measurements confirmed the crystalline nature and phase assemblages of the compositions. The kinetics of melting and crystallization appeared to vary significantly between the compositions. Impedance spectroscopy results indicated the electrical conductivity is acceptable with respect to processing in the CCIM. The success of processing either ceramic composition will depend on the thermal profiles throughout the CCIM. In particular, the working temperature of the pour spout relative to the bulk melter which can approach 1700°C. The Fe-MP composition is recommended to demonstrate proof of principle for crystalline simulated waste forms considering the current configuration of INL's CCIM. If proposed modifications to the CCIM can maintain a nominal temperature of 1600°C throughout the melter, drain, and pour spout, then the CAF-5%TM-MP composition should be considered for a proof of principle demonstration.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Processing of crack-free high density polycrystalline LiTaO3 ceramics

Our work achieved high density (99.9%) polycrystalline LiTaO 3 . The keys to the high density without cracking were the use of LiF-assisted densification to maintain fine grain size as well as the presence of secondary lithium aluminate phases as grain growth inhibitors. The average grain size of the hot pressed polycrystalline LiTaO 3 is less than 5 μm, limiting residual stresses caused by the anisotropic thermal expansion. Dilatometry results clearly indicate liquid phase sintering via the added LiF sintering aid. Efficient liquid phase sintering allows densification during low temperature hot pressing. Electron microscopy confirmed the high-density microstructure. Furthermore, Rietveld analysis of neutron diffraction data revealed the presence of LiAlO 2 and LiAl 5 O 8 minority phases and negligible substitutional defect incorporation in LiTaO 3 .

36 MATERIALS SCIENCE↗

Selected applications and processing techniques for LTCC.

Low Temperature Cofired Ceramic has proven itself in microelectronics, microsystems (including microfluidic systems), sensors, RF features, and various non-electronic applications. We will discuss selected applications and the processing associated with those applications. We will then focus on our recent work in the area of EMI shielding using full tape thickness features (FTTF) and sidewall metallization. The FTTF is very effective in applications with -150 dB isolation requirements, but presents obvious processing difficulties in full-scale fabrication. The FTTF forms a single continuous solid wall around the volume to be shielded by using sequential punching and feature-filling. We discuss the material incompatibilities and manufacturing considerations that need to be addressed for such structures and show preliminary implementations.

36 MATERIALS SCIENCE↗

Commercialization of Ultra-Hard Ceramics for Cutting Tools Final Report CRADA No. TC0279.0

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Greenleaf Corporation (Greenleaf) to develop the technology for forming unique precursor nano-powders process that can be consolidated into ceramic products for industry. LLNL researchers have developed a solgel process for forming nano-ceramic powders. The nano powders are highly tailorable, allowing the explicit design of desired properties that lead to ultra hard materials with fine grain size. The present CRADA would allow the two parties to continue the development of the sol-gel process and the consolidation process in order to develop an industrially sound process for the manufacture of these ultra-hard materials.

36 MATERIALS SCIENCE↗

Applying molecular dynamics simulations to the study of micro cold spray of yttria

Micro cold spray (MCS) is a novel manufacturing process with proven success depositing dense, thick films of technical ceramics without the need for elevated processing temperatures or chemical precursors. The process transforms a loose sub-micrometer powder into an adherent film with mechanical properties approaching that of the bulk material through a phenomenon known as room temperature impact consolidation. While this phenomenon has been demonstrated for a wide variety of ceramic materials and film substrates, yttria stands out as a material that is both well-characterized in experiments and of significant interest for industrial applications due to its excellent refractory properties. This dissertation seeks to investigate the fundamental mechanisms that enable room temperature impact consolidation by using molecular dynamics (MD) simulations of yttria particle impacts and characterizing the deformation behavior of the system.

36 MATERIALS SCIENCE↗

Study of Ion Conductivity and Chain Dynamics in Polymer-Ceramic Composite Electrolytes

We fabricated polymer-ceramic composite consisting of polyethylene oxide, lithium trifluoromethanesulfonate, and a lithium-conducting glass ceramic from Ohara corporation. We examined the ion conductivity of the composite electrolyte with high volume fractions of Ohara ceramic (30% to 60%) using various processing methods. In this composition range, the composite conductivity was less affected by the volume fraction of the ceramic. Instead, it was strongly affected by processing methods. We found that the composite showed lower ion conductivity than the conductivity of PEO and the Ohara ceramic. A trilayer experiment using polymer electrolyte/Ohara ceramic plate/polymer electrolyte design revealed a very large interfacial resistance between the polymer electrolyte and Ohara ceramic. Quasi-elastic neutron scattering measurements were performed on the system to shed light on underpinnings of the origin of this large interfacial resistance.

Chen, Xi↗

Recipe for coating ceramic blades for ion trapping

The first batches of ion traps patterned and coated were processed per the standard 3-step clean, air fire, and metallization processes. The third or fourth lot using this process resulted in poorly adhering metallization. Up until this point, the standard process was used to metallize and pattern ceramic ion traps without fail. At about the 4th batch of parts something changed. After the 5th batch, the ceramic ion traps received generally came with some unknown contamination that does not come off in a standard 3-step clean (Lenium Vapor Degreaser, Acetone, IPA) and air fire (860C for 1 hour) for which this process removes the vast majority of all contamination for most ceramic metallization. This is highly unusual. Using HF + Boiling H 2 O 2 is extreme for cleaning the ceramic ion traps. The contamination was never identified and is stubborn to effectively clean. Standard as-fired ceramic should be very easy to clean as if s fired at temperatures greater than 1400°C and not much in terms of contamination should exist at these temperatures, so there must be an intermediate step/process which is imparting this contamination. It is likely a polishing compound or previous polishing contaminant, but also not easily visually distinguishable until after metallization. The halo marks observed on parts might be fingerprints (less likely) or potential polishing marks (more likely) as metallization typically doesn't cover/hide any damage or contamination, but rather quite clearly the opposite, it accentuates it. Blotchy appearances in the metallization usually indicated an adhesion issue. As a result of the fragility of the parts (yield loss due to handling) and difficulty in identifying the contamination during cleaning, we have taken a conservative approach of HF + H 2 O 2 cleaning for all batches after the contamination and adhesion issues were identified.

36 MATERIALS SCIENCE↗

SUMMARY OF 2009 RHEOLOGY MODIFIER PROGRAM

The overall objective of the EM-31 Rheological Modifiers and Wetting Agents program is to utilize commercially available rheology modifiers to increase the solids fraction of radioactive sludge based waste streams, resulting in an increase in throughput and decreasing the overall processing time. The program first investigates the impact of rheology modifiers on slurry simulants and then utilizes the most effective rheology modifiers on radioactive slurries. The work presented in this document covers the initial investigation of rheology modifier testing with simulants. This task is supported by both the Savannah River National Laboratory (SRNL) and Pacific Northwest National Laboratory (PNNL). The SRNL EM-31 task, for this year, was to investigate the use of rheology modifiers on simulant Defense Waste Processing Facility (DWPF) melter feeds. The task is to determine, based on the impact of the rheology modifier, if there are rheology modifiers that could reduce the water content of the slurry going to the DWPF melter, hence increasing the melt rate by decreasing the water loading. The rheology modifier in essence would allow a higher solids content slurry to have the same type of rheology or pumpability of a lower solids slurry. The modifiers selected in this report were determined based on previous modifiers used in high level waste melter feed simulants, on-going testing performed by counterparts at PNNL, and experiences gain through use of modifiers in other Department of Energy (DOE) processes such as grout processing. There were 12 rheology modifiers selected for testing, covering both organic and inorganic types and they were tested at four different concentrations for a given melter feed. Five different DWPF melter feeds were available and there was adequate material in one of the melter feeds to increase the solids concentration, resulting in a total of six simulants for testing. The mass of melter feed available in each simulant was not adequate for testing each rheology modifier, hence based on the changes in rheology for a given rheology modifier, rheology modifiers were either dropped or added between simulants. Three rheology modifiers were used on all simulants. The results from this testing indicate that citric acid or polycarboxylate based rheology modifiers are the most effective in reducing the yield stress, by as much as 70% at the higher rheology modifier additions and were effective on most of the tested simulants. These rheology modifiers are organic, hence the can also be used as reductants in melter operations. The most effective non-organic rheology modifiers, sodium metasilicate reduced the yield stress by 10%. It is recommended that both citric acid and commercially available polycarboxylate rheology modifiers be further investigated. Different molecular weight polycarboxylates and different types of polycarboxylates used in other industries must be considered. These polycarboxylates are extensively utilized in the cement, ceramic, and water treatment processes, hence readily available. Future work on DWPF melter feeds involving rheology modifiers should include, assuming the present method of processing sludge through DPWF does not change, is: (1) Investigate the use of polycarboxylate in various processes and procure polycarboxylates for testing. Limit rheology modifier selection and future testing between four and eight different types. (2) Test rheology modifiers on at least two different chemical types or bounding DWPF SME product simulants. Test to include the impact of boiling and the effectiveness in reducing water content via rheology versus weight percent curves. (3) Based on selected modifiers, perform testing on actual radioactive melter feed based on results from simulant testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗

Cold sintering process of Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 solid electrolyte

Abstract The recently developed technique of cold sintering process (CSP) enables densification of ceramics at low temperatures, i.e., <300°C. CSP employs a transient aqueous solvent to enable liquid phase‐assisted densification through mediating the dissolution‐precipitation process under a uniaxial applied pressure. Using CSP in this study, 80% dense Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolytes were obtained at 120°C in 20 minutes. After a 5 minute belt furnace treatment at 650°C, 50°C above the crystallization onset, Li‐ion conductivity was 5.4 × 10 −5 S/cm at 25°C. Another route to high ionic conductivities ~10 −4 S/cm at 25°C is through a composite LAGP ‐ (PVDF‐HFP) co‐sintered system that was soaked in a liquid electrolyte. After soaking 95, 90, 80, 70, and 60 vol% LAGP in 1 M LiPF 6 EC‐DMC (50:50 vol%) at 25°C, Li‐ion conductivities were 1.0 × 10 −4 S/cm at 25°C with 5 to 10 wt% liquid electrolyte. This paper focuses on the microstructural development and impedance contributions within solid electrolytes processed by (i) Crystallization of bulk glasses, (ii) CSP of ceramics, and (iii) CSP of ceramic‐polymer composites. CSP may offer a new route to enable multilayer battery technology by avoiding the detrimental effects of high temperature heat treatments.

Berbano, Seth S.↗

Slip casting nano-particle powders for making transparent ceramics

A method of making a transparent ceramic including the steps of providing nano-ceramic powders in a processed or unprocessed form, mixing the powders with de-ionized water, the step of mixing the powders with de-ionized water producing a slurry, sonifing the slurry to completely wet the powder and suspend the powder in the de-ionized water, separating very fine particles from the slurry, molding the slurry, and curing the slurry to produce the transparent ceramic.

36 MATERIALS SCIENCE↗

Dielectric and piezoelectric properties of 0.970(0.95(K{sub 0.485}Na{sub 0.515})NbO{sub 3}–0.05LiSbO{sub 3})–0.015CuO–0.015Al{sub 2}O{sub 3}/PVDF 0–3 composite reinforced with two kinds of ZnO powder

0.970(0.95(K{sub 0.485}Na{sub 0.515})NbO{sub 3}–0.05LiSbO{sub 3})–0.015CuO–0.015Al{sub 2}O{sub 3} (KNNLS–CA) ceramic powder obtained through the conventional solid state reaction. The ZnO nanoparticles (denoted as ZnO1) and poly (vinylidene fluoride) (PVDF) were supplied from commercial companies. The self-synthesized ZnO powder (denoted as ZnO2) were prepared by hydrothermal method using Zn (CH{sub 3}COO){sub 2}·2H{sub 2}O and NaOH. Subsequently, the two kinds of composites were fabricated by hot-pressing process using KNNLS–CA ceramic powder, two kinds of ZnO powder and PVDF polymer. The effects of the ZnO on the crystalline structures, morphology, thermal stability, densities and electric properties of composites were studied systemically. The KNNLS–CA ceramic possesses a perovskite phase with orthorhombic symmetry and peaks from the second phase of K{sub 3}Li{sub 2}Nb{sub 5}O{sub 15} (PDF#52-0157) are detected by X-ray diffraction. PVDF polymer mainly possesses α, β and γ phases. Two kinds of ZnO all possess hexagonal wurtzite structures without any impurity phase. It is worth noting that the ZnO particles have great impacts on lattice constants, strain and crystallinity. In addition, the ZnO particles can enhance the relative fraction of β phase in PVDF and improve the thermal stability of the composite. Interestingly, the dielectric and piezoelectric properties are also found to be improved with the increase of ZnO content. Especially, when 10 wt.% ZnO2 is doped, the dielectric permittivity reaches the value of 586.4 (100 Hz) at room temperature and the piezoelectric constant is 64 pC/N. After 30 days of aging test, it is obvious that all the composites present a good stability of piezoelectric property.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Processing and consolidation of copper/tungsten

Here, we developed a copper/tungsten (Cu/W) composite for mesoscale Materials Science applications using the novel High-Energy Diffraction Microscopy (HEDM) technique. Argon-atomized copper powder was selected as the starting raw powder and screened to remove the extremely large particle fraction. Tungsten particles were collected by milling and screening the -325 mesh tungsten powder between 500 and 635 mesh sieves. Hot pressing of screened Cu powder was performed at 900 °C in Ar/4 %H 2 atmosphere. XRD and ICP results show that the hot-pressed Cu sample consists of about 5 vol% Cu 2 O, which is caused by the presence of oxygen on the surface of the starting Cu powder. Hot pressing the copper powder in a pure hydrogen atmosphere was successful in removing most of the surface oxygen. Our process was also implemented for hot pressing the Cu/W composite. The density of the Cu/W composites hot pressed at 950 °C in pure hydrogen was about 94 % of the theoretical density (TD). The hot-pressed Cu/W composites were further hot isostatic pressed at 1050 °C in argon atmosphere, which results in 99.6 % of the TD with the designed Cu grain size and W particle distribution. Tensile specimens with D-notch were machined using the wire EDM method. Furthermore, the processing and consolidation of these materials will be discussed in detail. The HEDM images are also showed and discussed.

36 MATERIALS SCIENCE↗

Progress and Technology Assessment of Melt-Cast Ceramic Waste Forms

The Savannah River National Laboratory (SRNL) conducted research from FY2011 – FY2020 to develop ceramic waste forms to treat High-Level Waste (HLW) resulting from reprocessing of commercial Used Nuclear Fuel (UNF) as part of the Department of Energy (DOE) office of Nuclear Energy (NE) Fuel Cycle Technologies (FCT) research program. The objective of the research was to develop a reference ceramic waste form and process technology needed to immobilize the combined HLW raffinate stream, including undissolved solids and soluble technetium, and potentially the TRU waste stream resulting from reprocessing processes. This report compiles the relevant literature produced under, and pertinent to, the program objectives and provides a perspective on the technology development as well as prospects for future.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

X-ray characterization technique for the assessment of surface damage in GaN wafers

SixPoint Materials has successfully switched to production of two-inch diameter GaN wafers using the ammonothermal method. Crystal quality values are high with dislocation densities typically in the low 10 5 cm -2 . In efforts to produce true epi-ready material, investigations were made to develop a technique to study surface damage caused by the back-end process using X-ray diffraction methods. Analysis of peak tailing from X-ray rocking curves of the (1 1 4) reflection indicates the progression of surface damage during each step of the back-end process. For instance, the tailing can be partially represented using full width five thousand max (FW5000M) values. By using a peak with a low glancing angle, such as the (1 1 4) reflection’s angle of 10.8662°, more of the X-ray beam is scattered in the surface region, providing an improved measurement of surface damage. Since this technique is non-destructive and can be performed without dismounting the sample from its ceramic back-end processing plate, it can provide information on the damaged layer at each stage of the back-end process. Using this technique to evaluate samples from various manufacturers, we found a lack of uniformity in surface damage from GaN companies. It is our hope that this technique will be adopted to better standardize surface damage measurements in the GaN field.

36 MATERIALS SCIENCE↗