Search NASA⌕ Search

SEARCH · Search NASA

Results for “compressibility factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Geometric transformations for video compression and human teleoperator display

A method for bandwidth-efficient processing of video imagery to be viewed by the teleoperator of a remotely-operated vehicle on which the camera is mounted is described. The method comprises image coding, transmission, and reconstruction. It is assumed that the transmission bandpass is the limiting factor rather than encoding/decoding schemata; that image coding and reconstruction will be done within the general abilities of the NASA/TI Programmable Remapper; and that the ratio of retained local detail to the operator's visual resolution is held constant throughout the large-field image that is seen. Novel features include that the compression and reconstruction address certain characteristics of the human visual system, that two-way communication controls a moving 'fovea' in the transformation, and that resolution varies over the image. Conventional motivations accommodated include the Cartesian raster-scan nature of available imagers and display devices and a need for low bandwidth in the image transmission. Unique image processing hardware, NASA's Programmable Remapper, allows demonstration of the method. Once refined, the technology could be adapted to special purpose imagers and display devices, or otherwise to dedicated image processing hardware.

Juday, Richard D.↗
NASA NTRS1978

A fracture specimen for high-temperature testing

A wedge-loaded tapered DCB specimen is proposed for fracture toughness and stable crack growth measurements of ceramic materials at elevated temperatures. The specimen is wedge-loaded by a compression pin seated in the starter notch. By appropriate selection of the specimen's taper and starter notch angle, the stress intensity factor is maintained relatively constant through 50 percent of the test section. Room temperature fracture toughness testings of commercial grade polycrystalline alumina specimens indicate that the crack will run straight for approximately 50 percent of the length of the test section without side grooving. A moderate 10 percent side grooving was sufficient to maintain straight crack extension throughout the entire specimen length.

Kobayashi, A. S.↗
NASA NTRS1982

Computations of transonic flow over an oscillating airfoil with shock-induced separation

A numerical study is presented on unsteady transonic flow over an airfoil in pitching oscillation at a moderately high incidence. The study was focused on the effects of unsteady shock-wave/boundary-layer interactions and subsequent flow separations. An implicit finite-difference scheme was used to solve the full time-dependent compressible Navier-Stokes equations in conservation-law form. The algorithm adopted for this study is the Beam-Warming spatially factored scheme. It is, however, constructed in a body-fitted curvilinear coordinate system for efficient unsteady flow computations. The computational results are compared with experimental data measured in the Ames 11- by 11-Foot Transonic Wind Tunnel.

Chyu, W. J.↗
NASA NTRS1980

Recent developments in the design, testing and impact-damage tolerance of stiffened composite panels

The structural technology of laminated filamentary-composite stiffened-panel structures under combined in-plane and lateral loadings is discussed. Emphasis is on analyzing the behavior of the structures under load, determining appropriate structural proportions for weight efficient configurations, and effects of impact damage and geometric imperfections on structural performance. Experimental data on buckling of panels under in-plane compression validate the analysis and sizing methods, and illustrate structural performance and efficiency obtained from representative structures. It is shown that the strength of panels under in-plane compression can be degraded by low-velocity impact damage, and data are presented which indicate that the matrix is a significant factor influencing tolerance to impact damage.

Williams, J. G.↗
NASA NTRS1982

Vortex motion in axisymmetric piston-cylinder configurations

By using the Beam and Warming implicit-factored method of solution of the Navier-Stokes equations, velocities were calculated inside axisymmetric piston cylinder configurations during the intake and compression strokes. Results are presented in graphical form which show the formation, growth and breakup of those vortices which form during the intake stroke by the jet issuing from the valve. It is shown that at bore-to-stroke ratio of less than unity, the vortices may breakup during the intake stroke. It is also shown that vortices which do not breakup during the intake stroke coalesce during the compression stroke.

Shih, T. I. P.↗
NASA NTRS1988

Comparison of boundary-layer transition on a cone and flat plate at Mach 3.5

NASA-Langley's Pilot Low-Disturbance Tunnel has been used to obtain boundary layer transition data on a cone and flat plate at Mach 3.5. The transition Reynolds numbers measured under these low noise conditions are higher than those in conventional noisy tunnels by a factor of 3 in the case of the cone and of seven in that of the flat plate. Transition predictions based on compressible linear stability theory and the e exp N method, for N=10, are in excellent agreement with the measured locations with transition onset for both the cone and flat plate under these low noise conditions.

Chen, F.-J.↗
NASA NTRS1992

Computation of turbulent, separated, unswept compression ramp interactions

Examination of the literature shows that the comparison between experiment and computation for highly separated unswept compression ramp flows is generally poor, irrespective of the turbulence model used. In general, the upstream influence is not correct, the wall pressure rise through separation is too steep, and the pressures under the separated shear layer are too high. In the current study, the objective is to determine if these discrepancies might be attributed more to other factors such as flowfield unsteadiness or three-dimensionality, rather than to inadequate turbulence modeling. To examine this possibility, multichannel wall pressure fluctuations were measured under the unsteady separation shock wave in a 28-deg unswept compression ramp flow at Mach 5. The results show that the large scale, low frequency separation shock unsteadiness controls the distribution of time-averaged surface properties and that neglect of the unsteadiness is probably the primary cause of the discrepancy between experiment and computation.

Marshall, T. A.↗
NASA NTRS1992

Delivery of cardiopulmonary resuscitation in the microgravity environment

The microgravity environment presents several challenges for delivering effective cardiopulmonary resuscitation (CPR). Chest compressions must be driven by muscular force rather than by the weight of the rescuer's upper torso. Airway stabilization is influenced by the neutral body posture. Rescuers will consist of crew members of varying sizes and degrees of physical deconditioning from space flight. Several methods of CPR designed to accommodate these factors were tested in the one G environment, in parabolic flight, and on a recent shuttle flight. Methods: Utilizing study participants of varying sizes, different techniques of CPR delivery were evaluated using a recording CPR manikin to assess adequacy of compressive force and frequency. Under conditions of parabolic flight, methods tested included conventional positioning of rescuer and victim, free floating 'Heimlich type' compressions, straddling the patient with active and passive restraints, and utilizing a mechanical cardiac compression assist device (CCAD). Multiple restrain systems and ventilation methods were also assessed. Results: Delivery of effective CPR was possible in all configurations tested. Reliance on muscular force alone was quickly fatiguing to the rescuer. Effectiveness of CPR was dependent on technique, adequate restraint of the rescuer and patient, and rescuer size and preference. Free floating CPR was adequate but rapidly fatiguing. The CCAD was able to provide adequate compressive force but positioning was problematic. Conclusions: Delivery of effective CPR in microgravity will be dependent on adequate resuer and patient restraint, technique, and rescuer size and preference. Free floating CPR may be employed as a stop gap method until patient restraint is available. Development of an adequate CCAD would be desirable to compensate for the effects of deconditioning.

Barratt, M. R.↗
NASA NTRS1947

The Effect of High Solidity on Propeller Characteristics at High Forward Speeds from Wind-Tunnel Tests of the NACA 4-(3)(06.3)-06 and NACA 4-(3)(06.4)-09 Two-Blade Propellers

Tests of two-blade propellers having the NACA 4-(3)(06.3)-06 and NACA 4-(3)(06.4)-09 blade designs (blade activity factors of 179 and 263, respectively) have been made in the Langley 8-foot high-speed tunnel through a range of blade angle from 20 degrees to 70 degrees for free-stream Mach numbers from 0.165 to 0.725 to determine the effects of high solidity and compressibility on propeller characteristics. The tests are part of a general investigation of propellers at high forward speeds. Results previously reported for similar tests of two-blade propellers having the NACA 4-308-03 and NACA 4-308-045 blade designs (blade activity factors of 87 and 133, respectively) are included for comparison. The results showed that the 0.06- and 0.09-solidity blades, although producing efficiencies of the order of 90 percent, were less efficient than blades of conventional solidity. The variation in average blade lift coefficient with solidity at a constant blade angle and advance-diameter ratio through the speed range of these tests was found to be analogous to the variation of wing lift coefficient with aspect ratio, indicating that high-solidity blades may be desirable at very high speeds. Because of power limitations of the test equipment, conclusive evidence of the possible favorable effects of increased blade solidity at high speeds was not obtained. Further tests are desirable.

Delano, James B.↗
NASA NTRS1987

Exposure time considerations in high temperature low cycle fatigue

The Conventional Strainrange Partitioning (CSRP) method for High-Temperature, Low-Cycle Fatigue (HTLCF) life prediction has its origins in the modeling of first-order, creep-fatigue waveform effects while treating as second-order effects, the influence of metallurgical or environmental time dependencies. Procedures are proposed to include the latter explicitly in the inelastic strainrange--life relations. For brevity, only the CP life relation will be presented in detail. The exposure-time effect within the CP inelastic strainrange (tensile creep reversed by compressive plasticity) was determined by tensile stresshold-time experiments for 316 SS at 816 C. Reductions in CP cyclic life of a factor of about two were observed with an increase in exposure time or a corresponding decrease in creep rate by a factor of about 100. The CP life relation has been modified to be expressed in terms of either Steady State Creep Rate (SSCR) or Exposure Time (ET). The applicability and accuracy of the time-dependent CP life relations is demonstrated by conducting verification experiments involving complex hysteresis loops. Metallographic examination revealed time-dependent degradation attributable to oxide formation and precipitation of carbides along grain boundaries.

Kalluri, S.↗
NASA NTRS1989

Rotordynamic coefficients for stepped labyrinth gas seals

The basic equations are derived for compressible flow in a stepped labyrinth gas seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equations. The first order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are presented in the form of a parametric study, since there are no known experimental data for the rotordynamic coefficients of stepped labyrinth gas seals. The parametric study investigates the relative rotordynamic stability of convergent, straight and divergent stepped labyrinth gas seals. The results show that, generally, the divergent seal is more stable, rotordynamically, than the straight or convergent seals. The results also show that the teeth-on-stator seals are not always more stable, rotordynamically, then the teeth-on-rotor seals as was shown by experiment by Childs and Scharrer (1986b) for a 15 tooth seal.

Scharrer, Joseph K.↗
NASA NTRS1988

Exposure time considerations in high temperature low cycle fatigue

The Conventional Strainrange Partitioning (CSRP) method for High-Temperature, Low-Cycle Fatigue (HTLCF) life prediction has its origins in the modeling of first-order, creep-fatigue waveform effects while treating as second-order effects, the influence of metallurgical or environmental time dependencies. Procedures are proposed to include the latter explicitly in the inelastic strainrange-life relations. For brevity, only the CP life relation will be presented in detail. The exposure-time effect within the CP inelastic strainrange (tensile creep reversed by compressive plasticity) was determined by tensile stresshold-time experiments for 316 SS at 816 C. Reductions in CP cyclic life of a factor of about two were observed with an increase in exposure time or a corresponding decrease in creep rate by a factor of about 100. The CP life relation has been modified to be expressed in terms of either Steady State Creep Rate (SSCR) or Exposure Time (ET). The applicability and accuracy of the time-dependent CP life relations is demonstrated by conducting verification experiments involving complex hysteresis loops. Metallographic examination revealed time-dependent degradation attributable to oxide formation and precipitation of carbides along grain boundaries.

Kalluri, S.↗
NASA NTRS1995

Krylov methods for compressible flows

We investigate the application of Krylov methods to compressible flows, and the effect of implicit boundary conditions on the implicit solution of nonlinear problems. Two defect-correction procedures, namely, approximate factorization (AF) for structured grids and ILU/GMRES for general grids, are considered. Also considered here are Newton-Krylov matrix-free methods that we combined with the use of mixed discretization schemes in the implicitly defined Jacobian and its preconditioner. Numerical experiments that show the performance of our approaches are then presented.

Tidriri, M. D.↗
NASA NTRS2015

Enhanced Performance of Streamline-Traced External-Compression Supersonic Inlets

A computational design study was conducted to enhance the aerodynamic performance of streamline-traced, external-compression inlets for Mach 1.6. The current study explored a new parent flowfield for the streamline tracing and several variations of inlet design factors, including the axial displacement and angle of the subsonic cowl lip, the vertical placement of the engine axis, and the use of porous bleed in the subsonic diffuser. The performance was enhanced over that of an earlier streamline-traced inlet such as to increase the total pressure recovery and reduce total pressure distortion

performance↗
NASA NTRS1997

Enhancement of Mixing and Reaction in High-speed Combustor Flowfields

Research has been underway for a number of years, both in the United States and abroad, to develop advanced aerospace propulsion systems for use late in this century and beyond. One program is now underway at the NASA Langley Research Research has been underway for a number of years, both in the United States and abroad, to develop advanced aerospace propulsion systems for use late in this century and beyond. One program is now underway at the NASA Langley Research Center to develop a hydrogen-fueled supersonic combustion ramjet (scramjet) that is capable of propelling a vehicle at hypersonic speeds in the atmosphere. A part of that research has been directed toward the optimization of the scramjet combustor and, in particular, the efficiency of fuel-air mixing and reaction taking place in the engine. In the high-speed vehicle configurations currently being considered, achieving a high combustor efficiency becomes particularly difficult. With increasing combustor Mach number, the degree of fuel-air mixing that can be achieved through natural convective and diffusive processes is reduced leading to an overall decrease in combustion efficiency and thrust. Compressible shear layers and jets provide a good model for studying the physical processes occurring in high speed mixing and combustion in a scramjet. Mixing layers are characterized by large scale eddies that form due to the high shear that is present between the fuel and the air streams. These eddies entrain the fuel and air into the mixing region between the fluids leading to increased surface area and locally steep concentration gradients. Molecular diffusion then occurs across the strained interfaces. In an early study of high-speed mixing, Brown and Roshko show that the spreading rate of a supersonic mixing layer decreases with increasing Mach number, exhibiting a factor of three decrease in spread rate as compared with an incompressible mixing layer with the same density ratio. They conclude that the reduced spread rate is primarily due to compressibility. Papamoschou and Roshko also observe that the spreading rate of compressible mixing layers is significantly reduced over that of incompressible layers. To characterize the structure of the flow quantitatively, they define a convective Mach number. The reduction in mixing layer spreading rate is shown in these experiments to correlate well with increasing convective Mach number.

Drummond, J. Philip↗
NASA NTRS2009

Stability Analysis of Roughness Array Wake in a High-Speed Boundary Layer

Computations are performed to examine the effects of both an isolated and spanwise periodic array of trip elements on a high-speed laminar boundary layer, so as to identify the potential physical mechanisms underlying an earlier transition to turbulence as a result of the trip(s). In the context of a 0.333 scale model of the Hyper-X forebody configuration, the time accurate solution for an array of ramp shaped trips asymptotes to a stationary field at large times, indicating the likely absence of a strong absolute instability in the mildly separated flow due to the trips. A prominent feature of the wake flow behind the trip array corresponds to streamwise streaks that are further amplified in passing through the compression corner. Stability analysis of the streaks using a spatial, 2D eigenvalue approach reveals the potential for a strong convective instability that might explain the earlier onset of turbulence within the array wake. The dominant modes of streak instability are primarily sustained by the spanwise gradients associated with the streaks and lead to integrated logarithmic amplification factors (N factors) approaching 7 over the first ramp of the scaled Hyper-X forebody, and substantially higher over the second ramp. Additional computations are presented to shed further light on the effects of both trip geometry and the presence of a compression corner on the evolution of the streaks.

Choudhari, Meelan↗
NASA NTRS1989

Structural development of laminar flow control aircraft chordwise wing joint designs

For laminar flow to be achieved, any protuberances on the surface must be small enough to avoid transition to turbulent flow. However, the surface must have joints between the structural components to allow assembly or replacement of damaged parts, although large continuous surfaces can be utilized to minimize the number the number of joints. Aircraft structural joints usually have many countersunk bolts or rivets on the outer surface. To maintain no mismatch on outer surfaces, it is desirable to attach the components from the inner surface. It is also desirable for the panels to be interchangeable, without the need for shims at the joint, to avoid surface discontinuities that could cause turbulence. Fabricating components while pressing their outer surfaces against an accurate mold helps to ensure surface smoothness and continuity at joints. These items were considered in evaluating the advantages and disadvantages of the joint design concepts. After evaluating six design concepts, two of the leading candidates were fabricated and tested using many small test panels. One joint concept was also built and tested using large panels. The small and large test panel deflections for the leading candidate designs at load factors up to +1.5 g's were well within the step and waviness requirements for avoiding transition.The small panels were designed and tested for compression and tension at -65 F, at ambient conditions, and at 160 F. The small panel results for the three-rib and the sliding-joint concepts indicated that they were both acceptable. The three-rib concept, with tapered splice plates, was considered to be the most practical. A modified three-rib joint that combined the best attributes of previous candidates was designed, developed, and tested. This improved joint met all of the structural strength, surface smoothness, and waviness criteria for laminar flow control (LFC). The design eliminated all disadvantages of the initial three-rib concept except for unavoidable eccentricity, which was reduced and reacted satisfactorily by the rib supports. It should also result in a relatively simple low-cost installation, and makes it easy to replace any panels damaged in the field.

Fischler, J. E.↗