Search NASA⌕ Search

SEARCH · Search NASA

Results for “content analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Characterisation of intra- and inter-C-S-H gel pore water in white cement based on an analysis of NMR signal amplitudes as a function of water content

{sup 1}H nuclear magnetic resonance (NMR) relaxation analysis of water in progressively dried white cement paste is used to estimate the width and relative specific area of intra-C-S-H sheet pores and inter-C-S-H particle gel pores. The measurement is based on the ratio of solid echo to free induction decay signal amplitudes and the observation that as water is removed, so the surface fraction contributing to the solid echo increases. The intra- and inter-C-S-H pores are found to be 1.5 nm and 4.1 nm thick respectively. The total specific area and volume ratio is 2.4 and 0.88 respectively. The volume ratio of readily evaporable water within the pore types is 0.63. Hence, the sheet porosity is 47% of the total or 38% if based solely on evaporable water. The method is distinct from NMR analyses based on the relaxation time. There is good agreement between the measured widths by the two methods.

36 MATERIALS SCIENCE↗

An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE)

The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile–butadiene–styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-performance polyvinyl chloride gel artificial muscle actuator with graphene oxide and plasticizer

A transparent and electroactive plasticized polyvinyl chloride (PVC) gel was investigated to use as a soft actuator for artificial muscle applications. PVC gels were prepared with varying plasticizer (dibutyl adipate, DBA) content. The prepared PVC gels were characterized using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and dynamic mechanical analysis. The DBA content in the PVC gel was shown to have an inverse relationship with both the storage and loss modulus. The electromechanical performance of PVC gels was demonstrated for both single-layer and stacked multi-layer actuators. When voltage was applied to a single-layer actuator and then increased, the maximum displacement of PVC gels (for PVC/DBA ratios of 1:4, 1:6, and 1:8) was increased from 105.19, 123.67, and 135.55µm (at 0.5kV) to 140.93, 157.13, and 172.94µm (at 1.0kV) to 145.03, 191.34, and 212.84µm (at 1.5kV), respectively. The effects of graphene oxide (GO) addition in the PVC gel were also investigated. The inclusion of GO (0.1 wt.%) provided an approximate 20% enhancement of displacement and 41% increase in force production, and a 36% increase in power output for the PVC/ GO gel over traditional plasticizer only PVC gel. The proposed PVC/GO gel actuator may have promising applications in artificial muscle, small mechanical devices, optics, and various opto-electro-mechanical devices due to its low-profile, transparency, and electrical response characteristics.

59 BASIC BIOLOGICAL SCIENCES↗

Topology of modified helical gears and Tooth Contact Analysis (TCA) program

The contents of this report covers: (1) development of optimal geometries for crowned helical gears; (2) a method for their generation; (3) tooth contact analysis (TCA) computer programs for the analysis of meshing and bearing contact of the crowned helical gears; and (4) modelling and simulation of gear shaft deflection. The developed method for synthesis was used to determine the optimal geometry for a crowned helical pinion surface and was directed to localize the bearing contact and guarantee favorable shape and a low level of transmission errors. Two new methods for generation of the crowned helical pinion surface are proposed. One is based on the application of a tool with a surface of revolution that slightly deviates from a regular cone surface. The tool can be used as a grinding wheel or as a shaver. The other is based on a crowning pinion tooth surface with predesigned transmission errors. The pinion tooth surface can be generated by a computer-controlled automatic grinding machine. The TCA program simulates the meshing and bearing contact of the misaligned gears. The transmission errors are also determined. The gear shaft deformation was modelled and investigated. It was found that the deflection of gear shafts has the same effect as gear misalignment.

Litvin, Faydor L.↗

IRAS observations of comets

The moderate spatial resolution and high sensitivity of the Infrared Astronomical Satellite (IRAS), which surveyed the celestial sphere during 1983 at wavelengths of 12, 25, 60, and 100 microns, were particularly well suited to detecting extended thermal emission from cometary dust. Sources with infrared color temperatures characteristic of solar system bodies, and at the ephemerides position of known comets were selected for analysis by the IRAS Asteroid Data Analysis System (ADAS). The data base is now available for use by researchers. This paper describes the development of the data base, details its entries, and presents a statistical analysis of its contents. The IRAS survey contains multiple observations of many periodic comets. A brief description and analysis is given of the observed infrared and derived physical properties for several comets of special interest.

Walker, R. G.↗

A hybrid approach to test-analysis-model development for large space structures

The present FEM reduction method for the generation of test-analysis-models (TAMs) in test-analysis correlation addresses contentions that the current modal TAM is hypersensitive to differences between test model shapes and analysis mode shapes, thereby generating large off-diagonal terms within the orthogonality and cross-orthogonality matrices employed in test-analysis mode-shape correlation. A hybrid TAM methodology is accordingly developed which combines the exact representation of the FEM target modes from the modal TAM with the more accurate TAM representation of the residual modes; the superior residual dynamics representation of the hybrid TAM is demonstrated for a detailed representation of a large space structure.

Kammer, D. C.↗

Radiation History of Fission Gamma-Ray Spectra Relevant to Post-Detonation Debris Analysis

Quantifying the fissile content within trace amounts of nuclear material is of significant importance to safeguards and nuclear forensics communities. Traditionally, measurement methods have relied on destructive analysis (DA) measurements or passive detection of gamma/neutron signatures through nondestructive assay (NDA). These methods are highly accurate and employed globally as both a nuclear forensics capability and a material accountability measurement. However, common DA techniques rely on sample dissolution, a time-consuming process which can be particularly difficult for certain sample matrices, such as melt-glass formed from nuclear fallout. Likewise, trace quantities of nuclear materials prove difficult to measure using passive NDA techniques due to relatively low emission rates and potential interference from activated materials within the sample matrix.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Spur gears: Optimal geometry, methods for generation and Tooth Contact Analysis (TCA) program

The contents of this report include the following: (1) development of optimal geometry for crowned spur gears; (2) methods for their generation; and (3) tooth contact analysis (TCA) computer programs for the analysis of meshing and bearing contact on the crowned spur gears. The method developed for synthesis is used for the determination of the optimal geometry for crowned pinion surface and is directed to reduce the sensitivity of the gears to misalignment, localize the bearing contact, and guarantee the favorable shape and low level of the transmission errors. A new method for the generation of the crowned pinion surface has been proposed. This method is based on application of the tool with a surface of revolution that slightly deviates from a regular cone surface. The tool can be used as a grinding wheel or as a shaver. The crowned pinion surface can also be generated by a generating plane whose motion is provided by an automatic grinding machine controlled by a computer. The TCA program simulates the meshing and bearing contact of the misaligned gears. The transmission errors are also determined.

Litvin, Faydor L.↗

The trace element chemistry of CaS in enstatite chondrites and some implications regarding its origin

The trace element distribution in oldhamite (CaS) extracted from enstatite chondrites was determined by INAA. Prior to extraction, the petrologic setting of the grains was studied microscopically, and their minor element contents determined by microprobe analysis; samples that displayed a wide range of minor element contents were selected for detailed elementary analysis. Those samples of CaS suspected to be more primitive on the basis of their minor element and petrologic siting contain the entire inventory of the host meteorite's light REE (LREE) and Eu, plus 30-50 percent of the heavy-REE inventory. In less primitive samples, the LREE are less enriched although Eu remains highly concentrated. Several other elements, including lithophiles and chalcophiles, are most enriched in the most primitive CaS. It is suggested that oldhamite played a key role in the redistribution of these elements during the metamorphism and evolution of enstatite-rich material.

Larimer, John W.↗

Analysis of Resistant Starches in Rat Cecal Contents Using Fourier Transform Infrared Photoacoustic Spectroscopy

Fourier transform infrared photoacoustic spectroscopy (FTIR-PAS) qualitatively and quantitatively measured resistant starch (RS) in rat cecal contents. Fisher 344 rats were fed diets of 55% (w/w, dry basis) starch for 8 weeks. Cecal contents were collected from sacrificed rats. A corn starch control was compared against three RS diets. The RS diets were high-amylose corn starch (HA7), HA7 chemically modified with octenyl succinic anhydride, and stearic-acid-complexed HA7 starch. To calibrate the FTIR-PAS analysis, samples from each diet were analyzed using an enzymatic assay. A partial least-squares cross-validation plot generated from the enzymatic assay and FTIR-PAS spectral results for starch fit the ideal curve with a R2 of 0.997. A principal component analysis plot of components 1 and 2 showed that spectra from diets clustered significantly from each other. This study clearly showed that FTIR-PAS can accurately quantify starch content and identify the form of starch in complex matrices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizations of Binary FeCr (AISI 430) Thin Films Deposited from a Single Magnetron Sputtering Under Easy Controllable Deposition Parameters

A series of 50-nm binary FeCr martensitic thin films were sputtered from a single source made of commercial AISI 430 ferritic stainless steel under the deposition rates gradually increased from 0.03 to 0.11 nm/s with 0.02 nm/s steps at stationary condition. And, under 0.09 nm/s deposition rate, a second series of the films were also deposited under the rotation speed of their substrates which was chosen at 0, 25, and 45 rpm. As far as we are concerned, this study is the first investigation of properties of the thin films produced from AISI 430. The atomic Fe content in the films increased from 79.3 to 98.6% while atomic Cr content decreased from 20.5 to 1.2% with the increase of deposition rate from 0.03 to 0.11 nm/s. According to compositional analysis, the Fe content increased while Cr content decreased with increasing deposition rate. The reason for this may be attributed to the relatively different bond energy/melting point of metals which have different contents sputtered from source material since this physical parameter is very significant for the sputtering process. And, the Fe content in the films decreased from 84.9 to 79.2 at. % while the Cr content increased from 14.9 to 20.6 at. % when the increase of rotation speed of substrate. The crystal structure of all films was observed to have a body-centered tetragonal phase and the intensity of (110) peak varied with the atomic Fe content. The surface observations of films performed by a scanning electron microscope exposed that the number of surface grains increased with the increase of deposition rate and decreased with the increase of rotation speed. According to surface roughness analysis done by an atomic force microscope, the roughness of the film surfaces increased as the deposition rate increased. And, the roughness of the film surfaces decreased as the rotation speed increased. This has been consistent with the grain size and roughness parameters. Thus, increasing deposition rate and decreasing rotation speed of the substrate caused an increase in grain size and roughness parameters. The magnetic measurements of the films achieved, by a vibrating sample magnetometer at room temperature, displayed that the saturation magnetization, M{sub s}, values increased from 820.1 to 1700.4 emu/cm{sup 3}, the remanence magnetization, M{sub r}, values increased from 293 to 817 emu/cm{sup 3}, and the coercivity, H{sub c}, value also increased from 38 to 107 Oe with the increasing of deposition rate. It is also seen that the magnetic easy axis are in the film plane due to the shape anisotropy. With the increase rotation speed, the values of M{sub s} and M{sub r} increased and the H{sub c} decreased. It was seen that variation of Fe content in the films influences the M{sub s} values and the H{sub c} values are consistent with the surface properties. It was concluded that the deposition rate and the rotation speed of the substrate play a considerable role on the structural and related magnetic properties of the sputtered FeCr thin films, and the properties of the films can be easily controlled by changing production parameters.

36 MATERIALS SCIENCE↗

Activity and Stability of (Pr 1-x Nd x ) 2 NiO 4 as Cathodes for Solid Oxide Fuel Cells: II. Electrochemical Performance and Performance Durability

Single phase (Pr 1-x Nd x ) 2 NiO 4 cathode powders (x = 0, 0.25, 0.50, 0.75, and 1.0) were synthesized via a glycine-nitrate combustion and high temperature calcination. Anode supported cells were used to investigate the cathode property. A reproducible performance, within 9% for each cathode composition, was observed providing a wealth of data for quantitative studies. Area specific resistance analysis and i-V measurements between 650 and 850°C showed a decrease in the cell performance with increasing Nd content. Impedance spectrum analysis suggests that the decline in performance results from an increase in electrode polarization. While Pr 2 NiO 4 cells showed significant performance degradation of 6.40%/1,000 hours, the degradation rate for (Pr 0.75 Nd 0.25 ) 2 NiO 4 cells was reduced by an order of magnitude (0.56%/1,000 hours) with a 7% lower power output. Furthermore, the cathodes with a higher Nd content showed further improvement in performance stability with a marginal degradation rate of 0.06%/1,000 hours.

25 ENERGY STORAGE↗

Annual productivity and lipid composition of native microalgae (Chlorophyta) at a pilot production facility in Southern California

Microalgae are an efficient platform for the sustainable production of foods, fuels, and bioproducts. Due to the vast natural diversity of microalgae, choosing an ideal species for production can be challenging, and laboratory-derived productivity data may be misleading. In the present study, nine species of green algae (Chlorophyta) were isolated directly from an outdoor pilot production facility, identified via sequencing and microscopy, cultured under standard laboratory conditions to assess lipid content, and then cultivated in 80-L cultures in a greenhouse over the course of a year to assess productivity. Analysis of lipid content from laboratory-grown cultures revealed that these strains had high concentrations of C16 and C18 fatty acids and lipid content not exceeding 30% of dry weight during growth phase. In the greenhouse, Parachlorella kessleri-SD23 had the highest annual productivity, yielding an annual average of approximately 19 g/m 2 /d and 88 mg/L/d of biomass productivity. Furthermore, P. kessleri-SD23 had a total lipid content equal to about 19% of dry weight during growth phase under laboratory conditions with the highest concentration of C18:2 and C18:3 fatty acids among the isolates.

09 BIOMASS FUELS↗

Process optimization of caustic scrubber and iodine-129 immobilization in sodalite-based waste forms

Caustic scrubbers are proposed to remove vaporized iodine from nuclear fuel reprocessing plants. Resulting caustic slurries of radioactive iodine ( 129 I) and other anions can be captured and immobilized into the cage structures of sodalite-type minerals. Here, mixed anion sodalites were hydrothermally synthesized from a simulated caustic scrubber solution containing hydroxide/water, carbonate, chlorine, bromine, iodine, nitrate, and nitrite ions with added kaolinite. Experiments were conducted with twenty-five different sets of process conditions. Resulting powders were characterized by quantitative X-ray diffraction (XRD) and multi-functional thermal analysis, including gravimetry, calorimetry, and mass spectrometry. Using statistical analysis, process variables were tailored to maximize conversion of kaolinite into cage silicates, immobilize caustic scrubber anions, and minimize amorphous content. Further, chemical analysis showed the incorporation of all the targeted ions into the solids. Detailed investigation of a batch characterized after washing (creating secondary waste) and one without washing but subsequent calcination is given. This work contributes to defining the constraints required for subsequent consolidation process steps of the waste form to avoid volatilization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Dose Rate Analysis Capability for Actual Spent Fuel Transportation Cask Contents

The approved contents for a U.S. Nuclear Regulatory Commission (NRC) licensed spent nuclear fuel casks are typically based on bounding used nuclear fuel (UNF) characteristics. However, the contents of the UNF canisters currently in storage at independent spent fuel storage installations are considerably heterogeneous in terms of fuel assembly burnup, initial enrichment, decay time, cladding integrity, etc. Used Nuclear Fuel Storage, Transportation & Disposal Analysis Resource and Data System (UNF ST&DARDS) is an integrated data and analysis system that facilitates automated cask-specific safety analyses based on actual characteristics of the as-loaded UNF. The UNF-ST&DARDS analysis capabilities have been recently expanded to include dose rate analysis of as-loaded transportation packages. Realistic dose rate values based on actual canister contents may be used in place of bounding dose rate values to support development of repackaging operations procedures, evaluation of radiation-related transportation risks, and communication with stakeholders. This paper describes the UNF-ST&DARDS dose rate analysis methodology based on actual UNF canister contents and presents sample dose rate calculation results.

Radulescu, Georgeta↗

Proposed Alternate Methodology for Preparation of a Documented Safety Analysis for the Transformational Challenge Reactor

10 CFR Part 830, Subpart B, Appendix A, Table 2 lists acceptable methodologies for development of a Documented Safety Analysis (DSA) for various types of nuclear facilities. The acceptable methodology listed for a DOE reactor is U.S. Nuclear Regulatory Commission Regulatory Guide 1.70, Standard Format and Content of Safety Analysis Reports for Nuclear Power Plants, or successor document. This document was developed for large commercial light-water power reactors. The difference between the Transformational Challenge Reactor (TCR) and commercial reactors in power output, radiological source term, fuel type and composition, and operational life span makes application of the Regulatory Guide to the TCR overly burdensome relative to the value added.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A STATISTICAL ANALYSIS OF THE LATE-TYPE STELLAR CONTENT IN THE ANDROMEDA HALO

We present a statistical characterization of the carbon-star to M-giant (C/M) ratio in the halo of M31. Based on the application of pseudo-filter bandpasses to our Keck/DEIMOS spectra, we measure the 81 - 77 color index of 1288 stars in the giant stellar stream and in halo fields out to large distances. From this well-established narrow-band system, supplemented by V - I colors, we find only a low number (five in total) of C-star candidates. The resulting low C/M ratio of 10% is consistent with the values in the M31 disk and inner halo from the literature. Although our analysis is challenged by small number statistics and our sample selection, there is an indication that the oxygen-rich M-giants occur in similar number throughout the entire halo. We also find no difference in the C-star population of the halo fields compared to the giant stream. The very low C/M ratio is at odds with the observed low metallicities and the presence of intermediate-age stars at large radii. Our observed absence of a substantial carbon-star population in these regions indicates that the (outer) M31 halo cannot be dominated by the debris of disk-like or Small-Magellanic-Cloud-type galaxies, but rather resemble the dwarf elliptical NGC 147.

79 ASTRONOMY AND ASTROPHYSICS↗