Search NASA⌕ Search

SEARCH · Search NASA

Results for “correlation multiscale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Multiphase flow studies for microscale hydrodynamics in the structured packed column

Post combustion carbon capture by solvent absorption in a structured packed column is a promising technology for mitigating greenhouse gas emissions. Computational fluid dynamic (CFD) modelling of such a column is a challenging multiscale problem due to the range in length and time scales. The microscale hydrodynamics play a key role in the overall column efficiency with the interfacial area significantly influencing the mass transfer between the gas and liquid phases. In this context, multiphase flow simulations using the volume of fluid (VOF) method in a representative elementary unit (REU) of the packed column can provide fundamental insights into the microscale hydrodynamics, such as, interfacial area and liquid holdup. The present paper systematically examines the impact of various factors (e.g., physical properties and contact angle) on the interfacial area. The results are compared with existing correlations and a scaling analysis is also performed. The solvent physical properties are characterized by the Kapitza number (Ka), a dimensionless number that depends only on fluid properties. So that the Ka number decreases with increasing viscosity. At a fixed liquid load, the interfacial area and liquid holdup are observed to increase with decreasing Ka number. The impact of contact angle (i.e., solid surface characteristics) is effectively investigated by modifying the wall boundary conditions. The interfacial area and liquid holdup are found to decrease with increasing contact angle. Subsequently, a phenomenological correlation for interfacial area is proposed that includes the impact of these parameters. Finally, this correlation may be used to predict the interfacial area for gas-liquid flow in a structured packing for rivulet to fully wetted flow regimes.

42 ENGINEERING↗

Energy landscape in Ni-Co-Cr and related alloys

Among multi-principal element alloys, the NiCoCr middle-entropy alloy has an outstanding combination of strength and ductility at both low and elevated temperatures. Equiatomic NiCoCr is a single-phase alloy with the face centered cubic (fcc) crystal structure. A low stacking fault energy in the fcc matrix is a cause of a relatively low creep in this alloy. The hexagonal close-packed (hcp) structure differs from the fcc by a stacking of atomic layers. The energy difference between the hcp and fcc structures is known to correlate with the stacking fault energy in the fcc phase. We compute formation and relative structural energies versus composition in the Ni-Co-Cr ternary and related quaternary systems, discuss possibilities of compositional adjustments, and compare theoretical predictions with experiment. We acknowledge funding by NASA’s Aeronautics Research Mission Directorate (ARMD) via Transformational Tools and Technologies (TTT) Project.

Multiscale↗

Multivariate and Multiscale Dependence in the Global Climate System Revealed Through Complex Networks

A systematic characterization of multivariate dependence at multiple spatio-temporal scales is critical to understanding climate system dynamics and improving predictive ability from models and data. However, dependence structures in climate are complex due to nonlinear dynamical generating processes, long-range spatial and long-memory temporal relationships, as well as low-frequency variability. Here we utilize complex networks to explore dependence in climate data. Specifically, networks constructed from reanalysis-based atmospheric variables over oceans and partitioned with community detection methods demonstrate the potential to capture regional and global dependence structures within and among climate variables. Proximity-based dependence as well as long-range spatial relationships are examined along with their evolution over time, yielding new insights on ocean meteorology. The tools are implicitly validated by confirming conceptual understanding about aggregate correlations and teleconnections. Our results also suggest a close similarity of observed dependence patterns in relative humidity and horizontal wind speed over oceans. In addition, updraft velocity, which relates to convective activity over the oceans, exhibits short spatiotemporal decorrelation scales but long-range dependence over time. The multivariate and multi-scale dependence patterns broadly persist over multiple time windows. Our findings motivate further investigations of dependence structures among observations, reanalysis and model-simulated data to enhance process understanding, assess model reliability and improve regional climate predictions.

54 ENVIRONMENTAL SCIENCES↗

Tracer-Guided Characterization of Dominant Pore Networks and Implications for Permeability and Wettability in Shale

Pore network characterization is an important aspect in unconventional reservoir evaluation. While application of the technique of scanning electron microscope (SEM) brings substantial advances in pore characterization in shale, understanding the connected pore network that dominates flow in shale samples is limited by using SEM alone because of small fields of view and lack of views of connectivity in 3D. In this research, a technique integrating tracer imbibition, micro-computed tomography (CT) imaging, and SEM imaging was developed to provide a solution for multiscale imaging in shale. Tracer imbibition indicates pore connectivity; micro-CT imaging after tracer imbibition thus provides an overview of the connected pore network at the millimeter scale. With guidance from micro-CT images after tracer imbibition, a more accurate and detailed characterization of pore systems and related mineralogy can be conducted using higher-resolution SEM. The method was applied to five samples from Wolfcamp and Eagle Ford Formations. Results reveal the effectiveness of the integrated method by showing different patterns of distribution of the dominant pore network and different controlling mineralogy. Dominant porosity, estimated from grayscale analyses, displays a good correlation with permeability. This result indicates that dominant porosity is more relevant to permeability than is total porosity. Results from imbibition tests are also compared with that from contact angle measurement, and important implications on wettability can be obtained. The integrated method thus has the capacity to link the dominant pore network and wettability with microscale to submicroscale mineralogy, which can help better understand the pore systems and fluid flow in shale. Plain Language Summary Pore network characterization and wettability are two important aspects in unconventional reservoir evaluation and are crucial to understanding the nature of shale oil or gas storage and production. Here, a new technique integrating tracer imbibition, micro-computed tomography imaging, and scanning electron microscope imaging was developed for a more representative and effective pore characterization in shale. This integrated technique can provide a direct visualization of the dominant pore network in a millimeter-scale sample and, at the same time, can provide a guided pore network characterization under nanoscale resolution. This method thus can generate results that are more representative and more accurate in a more efficient way compared with the traditional scanning electron microscope method. The new technique can also reveal the local wettability in microscale. High-resolution analysis on the tracer imbibition or fluid displacement and mineralogy can shed light on the local wettability and the controlling mineralogy in shale.

58 GEOSCIENCES↗

Strong reconnection electric fields in shock-driven turbulence

Turbulent magnetic reconnection in a quasi-parallel shock under parameters relevant to the Earth's bow shock is investigated by means of a two-dimensional particle-in-cell simulation. The addressed aspects include the reconnection electric field, the reconnection rate, and the electron and the ion outflow speeds. In the shock transition region, many current sheets are generated in shock-driven turbulence, and electron-only reconnection and reconnection where both ions and electrons are involved can occur in those current sheets. The electron outflow speed in electron-only reconnection shows a positive correlation with the theoretical speed, which is close to the local electron Alfvén speed, and a strong convection electric field is generated by the large electron outflow. As a result, the reconnection electric field becomes much larger than those in the standard magnetopause or magnetotail reconnection. In shock-driven reconnection that involves ion dynamics, both electron outflows and ion outflows can reach of the order of 10 times the Alfvén speed in the X-line rest frame, leading to a reconnection electric field the same order as that in electron-only reconnection. An electron-only reconnection event observed by the magnetospheric multiscale mission downstream of a quasi-parallel shock is qualitatively similar to those in the simulation and shows that the outflow speed reaches approximately half the local electron Alfvén speed, supporting the simulation prediction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multi Resolution In-Situ Testing and Multiscale Simulation for Creep Fatigue Damage Analysis of Alloy 617

This report outlines the research activities that were carried out for the integrated experimental and simulation investigation of creep-fatigue damage mechanism and life prediction of Nickel-based alloy, Inconel 617 at high temperatures (950° and 850°). First, a novel experimental design using a hybrid control technique is proposed. The newly developed experimental technique can generate different combinations of creep and fatigue damage by changing the experimental design parameters. Next, detailed imaging analysis and statistical data analysis are performed to quantify the failure mechanisms of the creep fatigue of alloy 617 at high temperatures. It is observed that the creep damage is directly associated with the internal voids at the grain boundaries and the fatigue damage is directly related to the surface cracking. It is also observed that the classical time fraction approach does not has a good correlation with the experimental observed damage features. An effective time fraction parameter is seen to have an excellent correlation with the material microstructural damage. Thus, a new empirical damage interaction diagram is proposed based on the experimental observations. Following this, a macro level viscoplastic model coupled with damage is developed to simulate the stress/strain response under creep fatigue loadings. A damage rate function based on the hysteresis energy and creep energy is proposed to capture the softening behavior of the material and a good correlation with life prediction and material hysteresis behavior is observed. The simulation work is extended to include the microstructural heterogeneity. A crystal plasticity finite element model considering isothermal and large deformation conditions at the microstructural scale has been developed for fatigue, creep-fatigue as well as creep deformation and rupture at high temperature. The model considers collective dislocation glide and climb of the grains and progressive damage accumulation of the grain boundaries. The glide model incorporates a slip resistance evolution model that characterizes the solute-drag creep effects and can capture well the stress-strain and stress time response of fatigue and creep-fatigue tests at various strain ranges and hold times. In order to accurately capture the creep strains that accumulate particularly at relatively low stress levels, a dislocation climb model has been incorporated into the crystal plasticity modeling framework. The dislocation climb model parameters are calibrated and verified through experimental creep tests performed at 950°. In addition, a cohesive zone model has been fully implemented in the context of the crystal plasticity finite element model to capture the intergranular creep damage. The parameters of the cohesive zone model have been calibrated using available experimental data. The numerical simulations illustrate the capability of the proposed model in capturing damage initiation and growth under creep loads as compared to the experimental observations. The microscale analysis sheds light on the crack initiation sites and propagation patterns within the microstructure. The model is also utilized to investigate the hybrid-controlled creep-fatigue tests and has been found to capture reasonably well the stress-strain response with different hold times and hold stress magnitudes.

36 MATERIALS SCIENCE↗

Strong Reconnection Electric Fields in Shock-Driven Turbulence

Turbulent magnetic reconnection in a quasi-parallel shock under parameters relevant to the Earth's bow shock is investigated by means of a two-dimensional particle-in-cell simulation. The addressed aspects include the reconnection electric field, the reconnection rate, and the electron and the ion outflow speeds. In the shock transition region, many current sheets are generated in shock-driven turbulence, and electron-only reconnection and reconnection where both ions and electrons are involved can occur in those current sheets. The electron outflow speed in electron-only reconnection shows a positive correlation with the theoretical speed, which is close to the local electron Alfvén speed, and a strong convection electric field is generated by the large electron outflow. As a result, the reconnection electric field becomes much larger than those in the standard magnetopause or magnetotail reconnection. In shock-driven reconnection that involves ion dynamics, both electron outflows and ion outflows can reach of the order of 10 times the Alfvén speed in the X-line rest frame, leading to a reconnection electric field the same order as that in electron-only reconnection. An electron-only reconnection event observed by the magnetospheric multiscale mission downstream of a quasi-parallel shock is qualitatively similar to those in the simulation and shows that the outflow speed reaches approximately half the local electron Alfvén speed, supporting the simulation prediction.

magnetic reconnection↗

Multiscale and Machine Learning Modeling for Additive Manufacturing

Additive manufacturing (AM) techniques provide the opportunity to simultaneously design new materials and components with complex structures in less time, enabling faster material developments. Even though compositionally similar, the texture of the materials produced by such techniques is significantly different from conventionally manufactured materials. Additively manufactured materials produces highly heterogeneous microstructure within a single build. Such variations in the microstructure make qualifying AM products challenging for extreme environment applications. Understanding the AM process and its influence on the materials’ microstructures/properties is paramount for evaluating the workability and performance of the manufactured materials. The performance of AM materials for advanced nuclear reactor applications is of interest to the Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy. Hence, considering the microstructural variabilities in the AM products and their impact on the performance of the material, it is important to correlate the process conditions to the final product and establish a process-structure-property- performance (PSPP) correlation for AM materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Center of Mass Estimation for a Spinning Spacecraft Using Doppler Shift of the GPS Carrier Frequency

A sequential filter is presented for estimating the center of mass (CM) of a spinning spacecraft using Doppler shift data from a set of onboard Global Positioning System (GPS) receivers. The advantage of the proposed method is that it is passive and can be run continuously in the background without using commanded thruster firings to excite spacecraft dynamical motion for observability. The NASA Magnetospheric Multiscale (MMS) mission is used as a test case for the CM estimator. The four MMS spacecraft carry star cameras for accurate attitude and spin rate estimation. The angle between the spacecraft nominal spin axis (for MMS this is the geometric body Z-axis) and the major principal axis of inertia is called the coning angle. The transverse components of the estimated rate provide a direct measure of the coning angle. The coning angle has been seen to shift slightly after every orbit and attitude maneuver. This change is attributed to a small asymmetry in the fuel distribution that changes with each burn. This paper shows a correlation between the apparent mass asymmetry deduced from the variations in the coning angle and the CM estimates made using the GPS Doppler data. The consistency between the changes in the coning angle and the CM provides validation of the proposed GPS Doppler method for estimation of the CM on spinning spacecraft.

Spacecraft↗

Center of Mass Estimation for a Spinning Spacecraft Using Doppler Shift of the GPS Carrier Frequency

A sequential filter is presented for estimating the center of mass (CM) of a spinning spacecraft using Doppler shift data from a set of onboard Global Positioning System (GPS) receivers. The advantage of the proposed method is that it is passive and can be run continuously in the background without using commanded thruster firings to excite spacecraft dynamical motion for observability. The NASA Magnetospheric Multiscale (MMS) mission is used as a test case for the CM estimator. The four MMS spacecraft carry star cameras for accurate attitude and spin rate estimation. The angle between the spacecraft nominal spin axis (for MMS this is the geometric body Z-axis) and the major principal axis of inertia is called the coning angle. The transverse components of the estimated rate provide a direct measure of the coning angle. The coning angle has been seen to shift slightly after every orbit and attitude maneuver. This change is attributed to a small asymmetry in the fuel distribution that changes with each burn. This paper shows a correlation between the apparent mass asymmetry deduced from the variations in the coning angle and the CM estimates made using the GPS Doppler data. The consistency between the changes in the coning angle and the CM provides validation of the proposed GPS Doppler method for estimation of the CM on spinning spacecraft.

Estimation↗

Enabling Efficient and Accurate Computational Studies of MOF Reactivity via QM/MM and QM/QM Methods

Electronic structure calculations can provide unique insight into metal–organic framework (MOF) reactivity and defect formation. Such calculations can be broadly categorized as utilizing either periodic or cluster models, each with their respective advantages and disadvantages. In the present study, we demonstrate how multiscale methods can leverage the advantages of both approaches to enable high levels of accuracy and computational efficiency in studies of MOF reactivity. Using defect formation in a zeolitic imidazolate framework (ZIF) as a prototypical example, we benchmark a quantum mechanics/molecular mechanics (QM/MM) scheme that enables highly efficient cluster-based calculations on MOFs. We demonstrate the importance of correctly accounting for the influence of both dative bond cleavage in the QM cluster and long-range mechanical coupling to the bulk to achieving accurate QM/MM studies of MOFs. We subsequently leverage these cluster models in a QM/QM scheme that goes beyond standard DFT to yield “gold-standard” correlated wave function results on MOFs at modest computational cost. Crucially, we find several cases in which the incorporation of these correlated corrections yields qualitatively important corrections over conventional DFT values.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Multiscale Approach to High-Resolution Ocean Profile Observations within a 4DVAR Analysis System

Most ocean data assimilation systems are tuned to process and assimilate observations to constrain features on the order of the mesoscale and larger. Typically this involves removal of observations or computing averaged observations. This procedure, while necessary, eliminates many observations from the analysis step and can reduce the overall effectiveness of a particular observing platform. Simply including these observations is not an option as doing so can produce an overdetermined, ill-conditioned problem that is more difficult to solve. An approach, presented here, aims to avoid such issues while at the same time increasing the number of observations within the assimilation. A two-step assimilation procedure with the four-dimensional variational data assimilation (4DVAR) system is adopted. The first step attempts to constrain the large-scale features by assimilating a set of super observations with appropriate background error correlation scales and error variances. The second step then attempts to correct smaller-scale features by assimilating the full observation set with shorter background error correlation scales and appropriate error variances; here the background state is taken as the analysis from the first step. Results using a real high-density observation set from underwater gliders in the region southeast of Iceland, collected during the 2017 Nordic Recognized Environmental Picture (NREP) experiment, will be shown using the Navy Coastal Ocean Model 4DVAR (NCOM-4DVAR).

54 ENVIRONMENTAL SCIENCES↗

Theoretical analysis of non‐ G aussian heterogeneity effects on subsurface flow and transport

Abstract Much of the stochastic groundwater literature is devoted to the analysis of flow and transport in Gaussian or multi‐Gaussian log hydraulic conductivity (or transmissivity) fields, ( x being a position vector), characterized by one or (less frequently) a multiplicity of spatial correlation scales. Yet Y and many other variables and their (spatial or temporal) increments, Δ Y , are known to be generally non‐Gaussian. One common manifestation of non‐Gaussianity is that whereas frequency distributions of Y often exhibit mild peaks and light tails, those of increments are generally symmetric with peaks that grow sharper, and tails that become heavier, as separation scale or lag between pairs of Y values decreases. A statistical model that captures these disparate, scale‐dependent distributions of Y and in a unified and consistent manner has been recently proposed by us. This new “generalized sub‐Gaussian (GSG)” model has the form where is (generally, but not necessarily) a multiscale Gaussian random field and is a nonnegative subordinator independent of G . The purpose of this paper is to explore analytically, in an elementary manner, lead‐order effects that non‐Gaussian heterogeneity described by the GSG model have on the stochastic description of flow and transport. Recognizing that perturbation expansion of hydraulic conductivity diverges when Y is sub‐Gaussian, we render the expansion convergent by truncating Y 's domain of definition. We then demonstrate theoretically and illustrate by way of numerical examples that, as the domain of truncation expands, (a) the variance of truncated Y (denoted by Y t ) approaches that of Y and (b) the pdf (and thereby moments) of Y t increments approach those of Y increments and, as a consequence, the variogram of approaches that of . This in turn guarantees that perturbing to second order in (the standard deviation of Y t ) yields results which approach those we obtain upon perturbing to second order in even as the corresponding series diverges. Our analysis is rendered mathematically tractable by considering mean‐uniform steady state flow in an unbounded, two‐dimensional domain of mildly heterogeneous Y with a single‐scale function G having an isotropic exponential covariance. Results consist of expressions for (a) lead‐order autocovariance and cross‐covariance functions of hydraulic head, velocity, and advective particle displacement and (b) analogues of preasymptotic as well as asymptotic Fickian dispersion coefficients. We compare these theoretically and graphically with corresponding expressions developed in the literature for Gaussian Y . We find the former to differ from the latter by a factor k = ( denoting ensemble expectation) and the GSG covariance of longitudinal velocity to contain an additional nugget term depending on this same factor. In the limit as Y becomes Gaussian, k reduces to one and the nugget term drops out.

Riva, Monica↗

Inter-ELM pedestal turbulence dynamics dependence on q 95 and temperature gradient

A series of dedicated experiments from DIII-D tokamak provide spatially and temporally resolved measurements of electron density and temperature, and multiscale and multichannel fluctuations over a wide range of conditions. Measurements of long wavelength density fluctuations in the type-I ELMing H-mode pedestal routinely revealed a coexistence of multiple instabilities that exhibit dramatic different dynamic behaviors as q 95 and temperature gradient are varied, apparently responsible for limiting pedestal temperature profiles. Two distinct frequency bands of density fluctuations are modulated with ELM cycle with frequency above 200kHz propagating in the electron diamagnetic direction in the lab frame (electron mode) and below 200kHz propagating in the ion diamagnetic direction (ion mode). The electron mode amplitude peaks near the electron temperature gradient region and increases with q 95 which seems to be correlated with the increased χ e at higher q 95 , similar to the characteristics expected for Micro-tearing Mode (MTM). At higher q 95 , during the inter-ELM period, the ion mode decays at later phase of the ELM cycle. Consistently, the poloidal correlation length of the ion mode is also found to reduce which suggests the possible E×B flow shear suppression of ion mode at later phase of the ELM cycle as the Er well recovers. In contrast, the electron mode grows during the ELM cycle and reaches saturation at around 50-60% of ELM period. Linear gyrokinetic simulations find the MTMs as the most unstable mode in the pedestal electron temperature gradient region. The higher q 95 and lower magnetic shear destabilize MTMs. These observations provide key insights of the underlying physics of multifield properties and rich dataset of experimental 'fingerprints' that enable new tests of the theoretical pedestal models and lead to developing a predictive model for pedestal formation on ITER and future burning plasma experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dynamic Data-Driven Multiscale Modeling for Predicting Microstructure and Mechanical Properties of 316L Stainless Steel

We have developed a long short-term memory stacked ensemble (LSTM-SE) surrogate modeling approach that can provide rapid predictions of microstructural evolution and the resultant mechanical properties of American Iron and Steel Institute (AISI) 316L series stainless steel (316LSS) fuel cladding under conditions of varying temperature and radiation dose rate. To acquire training data, we developed and implemented a kinetic Monte Carlo (KMC) model to simulate precipitation kinetics of M 23 C 6 , γ', and G phases within SS316L cladding. Experimentally reported precipitation kinetics of SS316L in literature were linked to the kinetic parameters of the simulated precipitation in our KMC model. The model was then used to simulate microstructure evolution under synthetically generated treatments of varying temperature and radiation dose rate, for periods of up to 3000 hours. Changes in volume fraction, number density, and particle size of precipitates were recorded, and particle area fractions were correlated using statistical methods to develop the surrogate model. Simultaneously, the mechanical properties of the simulated microstructures were evaluated using microstructure-based finite element method (FEM) analysis to determine the elastic modulus, yield stress, ultimate tensile strength, and elongation to failure of the aged microstructures. Using this approach, our surrogate model can predict precipitation behavior within 0.25% volume fraction and mechanical properties within 6% relative error from the values predicted by the KMC and FEM models using 50 training simulations as input. The trained recurrent neural network-based model can return estimations of precipitation kinetics and mechanical properties ~1000 times faster than the physics-based codes. This work demonstrates, as a proof of concept, that reactor material service lifetimes under variable service conditions can be predicted for a statistics-based model from a practicably obtainable dataset.

36 MATERIALS SCIENCE↗

Highly Resolved Mapping of NO 2 Vertical Column Densities From GeoTASO Measurements Over a Megacity and Industrial Area During the KORUS-AQ Campaign

The Korea–United States Air Quality (KORUS-AQ) campaign is a joint study between the United States National Aeronautics and Space Administration (NASA) and the South Korea National Institute of Environmental Research (NIER) to monitor megacity and transboundary air pollution around the Korean Peninsula using airborne and ground-based measurements. Here, tropospheric nitrogen dioxide (NO 2 ) slant column density (SCD) measurements were retrieved from Geostationary Trace and Aerosol Sensor Optimization (GeoTASO) L1B data during the KORUS-AQ campaign (2 May to 10 June 2016). The retrieved SCDs were converted to tropospheric vertical column densities using the air mass factor (AMF) obtained from a radiative transfer calculation with trace gas profiles and aerosol property inputs simulated with the Community Multiscale Air Quality (CMAQ) model and surface reflectance data obtained from the Moderate Resolution Imaging Spectroradiometer (MODIS). For the first time, we examine highly resolved (250 m × 250 m resolution) tropospheric NO 2 over the Seoul and Busan metropolitan regions and the industrial region of Anmyeon. We reveal that the maximum NO 2 vertical column densities (VCDs) were 4.94×10 16 and 1.46×10 17 molec. cm −2 at 09:00 and 15:00 LT over Seoul, respectively, 6.86×10 16 and 4.89×10 16 molec. cm −2 in the morning and afternoon over Busan, respectively, and 1.64×10 16 molec. cm −2 over Anmyeon. The VCDs retrieved from the GeoTASO airborne instrument were correlated with those obtained from the Ozone Monitoring Instrument (OMI) (r=0.48), NASA's Pandora Spectrometer System (r=0.91), and NO 2 mixing ratios obtained from in situ measurements (r=0.07 in the morning, r=0.26 in the afternoon over the Seoul, and r>0.56 over Busan). Based on our results, GeoTASO is useful for identifying NO 2 hotspots and their spatial distribution in highly populated cities and industrial areas.

Gyo-Hwang Choo↗

Defining and testing a granular continuum element

Continuum mechanics relies on the fundamental notion of amesoscopic volume "element" in which properties averaged over discreteparticles obey deterministic relationships. Recent work on granularmaterials suggests a continuum law may be inapplicable, revealinginhomogeneities at the particle level, such as force chains and slow cagebreaking. Here, we analyze large-scale Discrete-Element Method (DEM)simulations of different granular flows and show that a "granularelement" can indeed be defined at the scale of dynamical correlations,roughly three to five particle diameters. Its rheology is rather subtle,combining liquid-like dependence on deformation rate and solid-likedependence on strain. Our results confirm some aspects of classicalplasticity theory (e.g., coaxiality of stress and deformation rate),while contradicting others (i.e., incipient yield), and can guide thedevelopment of more realistic continuum models.

36 MATERIALS SCIENCE↗

Multiscale assessment of land surface phenology from harmonized Landsat 8 and Sentinel-2, PlanetScope, and PhenoCam imagery

As the spatial and temporal resolution of remotely sensed imagery has improved over the last four decades, algorithms for monitoring and mapping seasonal changes in surface properties have evolved rapidly. Most recently, the availability of daily PlanetScope imagery has created new opportunities for monitoring the land surface phenology (LSP) of terrestrial ecosystems at high spatial resolution. However, the quality and value of LSP information from PlanetScope imagery have not been systematically examined. In this paper, we evaluate the character and quality of LSP information derived from PlanetScope by comparing time series of vegetation indices and LSP metrics from PlanetScope to corresponding time series and LSP metrics derived from Harmonized Landsat 8 and Sentinel-2 (HLS) imagery and PhenoCams at six sites that span a diverse range of land cover types and climate. Results show that vegetation index time series from all three data sources show high temporal correlation, and LSP metrics derived from HLS, PlanetScope, and PhenoCam show high agreement with negligible bias. Semi-variograms for phenometrics estimated from PlanetScope imagery indicate that the majority of spatial variance captured in PlanetScope phenometrics occurs well below the spatial resolution HLS imagery. At the same time, LSP metrics from HLS are most strongly correlated with the 50–75% quantiles of 3 m LSP metrics from PlanetScope. This indicates that HLS captures the average phenology at sub-pixel scale captured in PlanetScope imagery. Here, our results represent the first comprehensive comparison of LSP metrics estimated from PlanetScope and publicly available moderate spatial resolution imagery, and provide insights regarding: (1) the quality and character of LSP metrics derived from HLS and PlanetScope; and (2) the relative merits and trade-offs associated with the use of each data source for LSP studies.

54 ENVIRONMENTAL SCIENCES↗