Search NASA⌕ Search

SEARCH · Search NASA

Results for “crack growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effects of secondary void-initiating particles on the steady-state crack growth resistance of high-strength steel

In this investigation, we focus on the dependence of stable crack growth resistance, as measured by the short-rod fracture toughness test, on secondary void-initiating particles such as AlN and Ti-based grain-refining precipitates in a variety of high-strength steels with tempered martensitic microstructures. The model developed by Ritchie and Thompson is modified to illustrate the significant amounts of toughening that can result from the refinement of secondary particles. Analysis of the data suggests that material strength is a predominant factor in increasing the short-rod fracture toughness relative to linear-elastic measures of initiation fracture toughness, but the extent of toughening is limited by the size and number density of secondary particles in the microstructure. The variation in estimates of secondary microvoid initiation and growth strains with precipitate size reinforce the notion that primary fracture at non-metallic inclusions and secondary fracture at smaller particles occur as sequential processes with a degree of concurrence that is dependent on the state of precipitation in both particle dispersions. Toughening in this connection is maximized by increases in microvoid growth strain that result from decreases in the size and areal number density of secondary void-initiating particles. Finally, the occurrence of transient instabilities during crack extension in short-rod specimens is explained with a phenomenological model that relates crack growth stability to natural variations in the dispersion of secondary void-initiating particles in the microstructure.

42 ENGINEERING↗
NASA NTRS1999

Development of a Practical Methodology for Elastic-Plastic and Fully Plastic Fatigue Crack Growth

A practical engineering methodology has been developed to analyze and predict fatigue crack growth rates under elastic-plastic and fully plastic conditions. The methodology employs the closure-corrected effective range of the J-integral, delta J(sub eff) as the governing parameter. The methodology contains original and literature J and delta J solutions for specific geometries, along with general methods for estimating J for other geometries and other loading conditions, including combined mechanical loading and combined primary and secondary loading. The methodology also contains specific practical algorithms that translate a J solution into a prediction of fatigue crack growth rate or life, including methods for determining crack opening levels, crack instability conditions, and material properties. A critical core subset of the J solutions and the practical algorithms has been implemented into independent elastic-plastic NASGRO modules. All components of the entire methodology, including the NASGRO modules, have been verified through analysis and experiment, and limits of applicability have been identified.

McClung, R. C.↗
NASA NTRS1999

Development of a Practical Methodology for Elastic-Plastic and Fully Plastic Fatigue Crack Growth

A practical engineering methodology has been developed to analyze and predict fatigue crack growth rates under elastic-plastic and fully plastic conditions. The methodology employs the closure-corrected effective range of the J-integral, (Delta)J(sub eff), as the governing parameter. The methodology contains original and literature J and (Delta)J solutions for specific geometries, along with general methods for estimating J for other geometries and other loading conditions, including combined mechanical loading and combined primary and secondary loading. The methodology also contains specific practical algorithms that translate a J solution into a prediction of fatigue crack growth rate or life, including methods for determining crack opening levels, crack instability conditions, and material properties. A critical core subset of the J solutions and the practical algorithms has been implemented into independent elastic-plastic NASGRO modules. All components of the entire methodology, including the NASGRO modules, have been verified through analysis and experiment, and limits of applicability have been identified.

McClung, R. C.↗
NASA NTRS1979

Interlaminar crack growth in fiber reinforced composites during fatigue

This paper presents an investigation of interlaminar crack growth behavior in fiber-reinforced composites subjected to fatigue loading. In the experimental phase of the study, interlaminar crack propagation rates and mechanisms were determined for the cases of various geometries, laminate parameters and cyclic stress levels. An advanced singular hybrid-stress finite element method was used in conjunction with the experimental results to examine the local crack-tip behavior and to characterize the crack propagation during fatigue. Results elucidate the basic nature of the cyclic delamination damage and relate the interlaminar crack growth rate to the range of mixed-mode crack-tip stress intensity factors. The study provides fundamental insight into the problem, reveals several important features of the interlaminar fatigue failure, and should be of practical importance in selection, testing and design of composite materials.

Wang, S. S.↗
DOE OSTI2024

Atomic force microscopy monitoring of subcritical slow crack growth in soda lime silicate glass

Prediction of brittle fracture in silicate glasses requires a fundamental understanding of slow crack growth rates, far below the critical stress intensity (K IC ) of the material. Here, in this study, atomic force microscopy (AFM) was used to characterize slow crack propagation in soda lime silicate glasses. Using large-sample AFM systems with specialized tips and scanners, fractures less than 20 nm wide were measured as a function of relative humidity (RH). The results were found to be sensitive to the type of AFM tip used and to the dryness of the surface. Continuous scanning and image capture over several days allowed the determination of the crack tip velocity. The dependance of crack tip velocity on RH was measured by enclosing the sample and AFM head in a humidity-controlled chamber. The crack tip velocity was measured as low 4.0×10 -12 m/s at 15 % RH and as high as 3.7×10 -10 m/s at 40 % RH. Overall crack growth was smooth during the AFM scan. Additionally, recession of the crack tip was noted as the sample dried, indicating crack tip closure may be occurring. Further studies on alternative compositions will provide details on subcritical fracture processes in a range of different environmental conditions.

Atomic force microscopy↗
DOE OSTI2025

XFEM Development for Modeling Crack Growth in Prototypical Welded Components

Nuclear power plant components are subjected to harsh operating environments that can lead to multiple degradation mechanisms in which fracture can play a prominent role. Predicting crack growth is important for assessing the integrity of welded components. The extended finite element method (XFEM) is an important tool for modeling such crack growth, and XFEM capabilities have been developed within the MOOSE framework. This report documents work in the MOOSE XFEM module to model fractures in three-dimensional representations of components using a topologically two-dimensional mesh to define cutting planes. Crack growth algorithms have been implemented to evolve the cutting mesh based on equations for stress corrosion cracking. Additionally, several usability and robustness improvements have been developed to enable three-dimensional fracture simulations. The cutting algorithms were demonstrated on a three-dimensional model of a prototypical reactor component undergoing stress corrosion cracking driven by idealized weld residual stresses. This is an incremental step toward using this capability to model more complex components with residual stresses computed through welding process simulations.

42 - ENGINEERING↗
NASA NTRS1984

An elastic-plastic finite element analysis of crack initiation, stable crack growth, and instability

Studies have been conducted to develop efficient techniques to simulate crack extension and to examine various local and global fracture criteria. Of the considered criteria, the crack-tip-opening angle (CTOA) or displacement (CTOD) at a specified distance from the crack tip was shown to be most suited for modeling stable crack growth and instability during the fracture process. The results obtained in a number of studies show the necessity for studying different crack configurations when assessing the validity of any fracture criteria. One of the objectives of the present investigation is related to a critical evaluation of the CTOD growth criterion using an elastic-plastic finite element analysis under monotonic loading to failure. The analysis was found to predict three stages of crack growth behavior under monotonic loading to failure. Calculated CTOD values agreed well with experimental values for crack growth initiation.

Newman, J. C., Jr.↗
NASA NTRS1983

Fatigue crack growth and low cycle fatigue of two nickel base superalloys

The fatigue crack growth and low cycle fatigue behavior of two P/M superalloys, Rene 95 and Astroloy, in the hot isostatically pressed (HIP) condition, was determined. Test variables included frequency, temperature, environment, and hold times at peak tensile loads (or strains). Crack initiation sites were identified in both alloys. Crack growth rates were shown to increase in argon with decreasing frequency or with the imposition of hold times. This behavior was attributed to the effect of oxygen in the argon. Auger analyses were performed on oxide films formed in argon. Low cycle fatigue lives also were degraded by tensile hold, contrary to previous reports in the literature. The role of environment in low cycle fatigue behavior is discussed.

Stoloff, N. S.↗
NASA NTRS2017

Crack Growth Testing of an Aluminum Oxynitride (AlON) for International Space Station Kick Panes

The mechanical properties of an aluminum oxynitride supplied as ground beams and disks were measured using ASTM International (formerly American Society for Testing and Materials) standard test methods. The slow crack growth tests were complicated by a "short" finish that increased strength scatter. Refining of the finish by more material removal in the second stage of grinding or the use of uniaxial grinding as specified in ASTM C1499 might have avoided the issue. The structural design parameters are an elastic modulus of E = 319 GPa, Poisson's ratio of v = 0.26, a fracture toughness of KIvb(A) = 2.18 MPa/m, slow crack growth (SCG) parameter n = 36, and SCG parameter A = 1.96 x 10-11 m/s.(MPa/m)n. For a ground finish, the Weibull parameters are a mean modulus of m = 14.0 and characteristic strength of sigma theta = 250.2 MPa. The 2015 vintage material exhibits similar mechanical properties to a 2010 vintage billet. Indentation flaws were not sensitive to the inherent crack growth mechanisms of this material and produced misleading results.

strength↗
DOE OSTI2020

On the fatigue crack growth behavior of Ti–10V–2Fe–3Al in gaseous hydrogen

Here, the fatigue crack growth behavior of Ti–10V–2Fe–3Al in gaseous hydrogen (H 2 ) was assessed through comparative experiments conducted in laboratory air and 8.3 MPa H 2 . The measured fatigue crack growth rate (da/dN) versus applied stress intensity factor range (ΔK) relationships and observed fracture morphologies for laboratory air and H 2 were comparable up to ΔK ≈ 6.9 MPa√m, when tested at a load ratio of 0.1 and frequency of 10 Hz. At higher ΔK values, significant crack deflection and subsequent catastrophic failure occurred in the specimen tested in H 2 . This degradation was not observed in a specimen pre-exposed to 8.3 MPa H 2 for 96 h and then immediately tested in laboratory air. X-ray diffraction of the failed H 2 -tested specimen revealed that the material remnants were predominantly composed of TiH 2 , suggesting that hydride formation was the catalyst for catastrophic failure in H 2 . The mechanistic implications of these results and their impact on current material compatibility assessments for Ti alloys in hydrogen service are then discussed.

08 HYDROGEN↗
NASA NTRS1974

Crack-growth behavior in thick welded plates of Inconel 718 at room and cryogenic temperatures

Results of mechanical-properties and axial-load fatigue and fracture tests performed on thick welded plates of Inconel 718 superalloy are presented. The test objectives were to determine the tensile strength properties and the crack-growth behavior in electron-beam, plasma-arc, and gas tungsten are welds for plates 1.90 cm (0.75 in) thick. Base-metal specimens were also tested to determine the flaw-growth behavior. The tests were performed in room-temperature-air and liquid nitrogen environments. The experimental crack-growth-rate data are correlated with theoretical crack-growth-rate predictions for semielliptical surface flaws.

Forman, R. G.↗
NASA NTRS1990

Elevated temperature crack growth in aluminum alloys: Tensile deformation of 2618 and FVS0812 aluminum alloys

Understanding the damage tolerance of aluminum alloys at elevated temperatures is essential for safe applications of advanced materials. The objective of this project is to investigate the time dependent subcritical cracking behavior of powder metallurgy FVS0812 and ingot metallurgy 2618 aluminum alloys at elevated temperatures. The fracture mechanics approach was applied. Sidegrooved compact tension specimens were tested at 175, 250, and 316 C under constant load. Subcritical crack growth occurred in each alloy at applied stress intensity levels (K) of between about 14 and 25 MPa/m, well below K (sub IC). Measured load, crack opening displacement and displacement rate, and crack length and growth rate (da/dt) were analyzed with several continuum fracture parameters including, the C-integral, C (sub t), and K. Elevated temperature growth rate data suggest that K is a controlling parameter during time dependent cracking. For FVS0812, da/dt is highest at 175 C when rates are expressed as a function of K. While crack growth rate is not controlled by C (sub t) at 175 C, da/dt appears to better correlate with C (sub t) at higher temperatures. Creep brittle cracking at intermediate temperatures, and perhaps related to strain aging, is augmented by time dependent transient creep plasticity at higher temperatures. The C (sub t) analysis is, however, complicated by the necessity to measure small differences in the elastic crack growth and creep contributions to the crack opening displacement rate. A microstructural study indicates that 2618 and FVS0812 are likely to be creep brittle materials, consistent with the results obtained from the fracture mechanics study. Time dependent crack growth of 2618 at 175 C is characterized by mixed transgranular and intergranular fracture. Delamination along the ribbon powder particle boundaries occurs in FVS0812 at all temperatures. The fracture mode of FVS0812 changes with temperature. At 175 C, it is characterized as dimpled rupture, and at 316 C as mixed matrix superplastic rupture and matrix-dipersoid debonding.

Leng, Yang↗
NASA NTRS2000

Simulating Fatigue Crack Growth in Spiral Bevel Gears

The majority of helicopter transmission systems utilize spiral bevel gears to convert the horizontal power from the engine into vertical power for the rotor. Due to the cyclical loading on a gear's tooth, fatigue crack propagation can occur. In rotorcraft applications, a crack's trajectory determines whether the gear failure will be benign or catastrophic for the aircraft. As a result, the capability to predict crack growth in gears is significant. A spiral bevel gear's complex shape requires a three dimensional model of the geometry and cracks. The boundary element method in conjunction with linear elastic fracture mechanics theories is used to predict arbitrarily shaped three dimensional fatigue crack trajectories in a spiral bevel pinion under moving load conditions. The predictions are validated by comparison to experimental results. The sensitivity of the predictions to variations in loading conditions and crack growth rate model parameters is explored. Critical areas that must be understood in greater detail prior to predicting more accurate crack trajectories and crack growth rates in three dimensions are identified.

Spievak, Lisa E.↗
NASA NTRS1990

Micromechanical model of crack growth in fiber reinforced ceramics

A model based on the micromechanical mechanism of crack growth resistance in fiber reinforced ceramics is presented. The formulation of the model is based on a small scale geometry of a macrocrack with a bridging zone, the process zone, which governs the resistance mechanism. The effect of high toughness of the fibers in retardation of the crack advance, and the significance of the fiber pullout mechanism on the crack growth resistance, are reflected in this model. The model allows one to address issues such as influence of fiber spacing, fiber flexibility, and fiber matrix friction. Two approaches were used. One represents the fracture initiation and concentrated on the development of the first microcracks between fibers. An exact closed form solution was obtained for this case. The second case deals with the development of an array of microcracks between fibers forming the bridging zone. An implicit exact solution is formed for this case. In both cases, a discrete fiber distribution is incorporated into the solution.

Rubinstein, Asher A.↗
DOE OSTI2022

Transient creep‐fatigue crack growth in creep‐brittle materials: Application to Alloy 718

Abstract This study presents incremental finite element computations of creep‐fatigue crack growth in Alloy 718 at in air. Alloy 718 is representative of creep‐brittle materials, in which viscoplastic deformation is restricted near the tip of a growing crack. The computations predict crack growth using a unique combination of an irreversible cohesive zone formulation and a strain gradient viscoplastic material model based on the Kocks–Mecking formulation. Cohesive zone damage parameters are estimated using sustained loading and constant‐amplitude cyclic loading experiments. Computations of crack extension under three different waveforms containing overloads all predict post‐overload retardation. The amount of retardation depends strongly on the overload ratio, consistent with experiments in the literature using similar waveforms. Analysis of the crack‐tip fields demonstrates retardation is associated with unloading in the highly deformed material near the advancing crack tip. Dynamic recovery and geometrically necessary dislocations are shown to significantly influence post‐overload crack extension.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

The properties and microstructure of Type 304L stainless steel produced by two additive manufacturing (AM) methods—directed energy deposition (DED) and powder bed fusion (PBF)—are evaluated and compared. Localized heating and steep temperature gradients of AM processes lead to significant residual stress and distinctive microstructures, which may be process-specific and influence mechanical behavior. Test data show that materials produced by DED and PDF have small differences in tensile strengths but clear differences in residual stress and microstructural features. Measured fatigue crack growth rates (FCGRs) for cracks propagating parallel to and perpendicular to the build directions differ between the two AM materials. To separate the influences of residual stress and microstructure, K-control test procedures with decreasing and constant stress intensity factor ranges are used to measure FCGRs in the near-threshold regime (crack growth rates ≤ 1 × 10 −8 m/cycle). Residual stress is quantified by the residual stress intensity factor, K res , measured by the online crack compliance method. Correcting the FCGR data for differences in K res brings results for specimens of the two AM materials into agreement with each other and with results for wrought specimens, when the latter are corrected for crack closure. Differences in microstructure and tensile strength have an insignificant influence on FCGRs in these tests.

additive manufacturing↗
DOE OSTI2020

The roles of yield strength mismatch, interface strength, and plastic strain gradients in fatigue crack growth across interfaces

An irreversible cohesive zone model was used to understand how plastic strain gradients and yield strength mismatches affect fatigue crack growth across bi-material and multilayer interfaces for a range of interface strengths. Parametric studies identified regimes of penetration through the interface, deflection into the interface, and a transition where cracks extend on both paths. Plastic strain gradients strongly influence the transition regime, and a yield strength mismatch is necessary to cause deflection. For crack growth across an interlayer, interactions between the interfaces occur when the crack-tip plastic zone spans the interlayer. Plastic strain gradients promote penetration through the interlayer.

42 ENGINEERING↗
NASA NTRS1991

Fatigue crack growth reliability by probabilistic finite elements

Fusion of the probabilistic finite-element method and reliability analysis for probabilistic fatigue-crack growth is presented. A comprehensive method for determining the probability of fatigue failure for mixed-mode cyclic loading is also presented. The loading is mixed-mode with randomness in the initial and final crack lengths, initial crack angle and position, material properties, crack-growth law, crack-direction law, and loading. The methodology consists of calculating the reliability index via an optimization procedure which is used to calculate the probability of fatigue failure. Performance of the methodology presented is demonstrated on a classical mode-I fatigue problem.

Besterfield, Glen H.↗