Search NASA⌕ Search

SEARCH · Search NASA

Results for “deformation twin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

251 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental investigation of the dependence of void nucleation and growth on initial microstructure in high-purity titanium under tension

An experimental investigation of failure mechanisms in relation to the initial microstructure in high-purity titanium samples is presented. The initial microstructure of the specimens was measured in 3D using diffraction-contrast tomography (DCT). Ex-situ X-ray computed tomography (XCT) was used to visualize voids in specimens at various levels of deformation attained by interrupted tensile testing. Electron backscatter diffraction (EBSD) mapping was used to characterize the deformed microstructures per specimen. The investigation showed that the location of failures was unrelated to the formation of the first voids, but rather the nucleation and growth of cracks were from heavily deformed surface regions. The areas surrounding the failure-causing cracks had the highest propensity for void development of any area in the specimen. This facilitated crack propagation through the specimen via “linking up”. The failure of the specimens by microvoid coalescence was bolstered by “dimpled” fracture surfaces. Paint composed of gallium embedded in rubber was used to track the displacement of points along the loading direction of the specimens, to relate the location of failure to the material's initial microstructure. However, the correlation proved difficult, due to complex microstructural evolution involving voids, grain fragmentations, and profuse twinning. Nevertheless, it was shown that necking occurred near the largest grain in the gauge section of the specimens. This is likely caused by the decrease in strength of larger grains, causing strain to concentrate in their vicinity. Here, a comprehensive picture of the failure processes in high-purity titanium under axial loading is presented and discussed in the paper.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding the plasticity contributions during laser-shock loading and spall failure of Cu microstructures at the atomic scales

A hybrid atomic-scale and continuum modeling framework is used to study the microstructural evolution during the laser-induced shock deformation and failure (spallation) of copper microstructures. A continuum two-temperature model (TTM) is used to account for the interaction of Cu atoms with a laser in molecular dynamics (MD) simulations. The MD-TTM simulations study the effect of laser loading conditions (laser fluence) on the microstructure (defects) evolution during various stages of shock wave propagation, reflection, and interaction in single-crystal (sc) Cu systems. In addition, the role of the microstructure is investigated by comparing the defect evolution and spall response of sc-Cu and nanocrystalline (nc) Cu systems. The defect (stacking faults and twin faults) evolution behavior in the metal at various times is further characterized using virtual in situ selected area electron diffraction and x-ray diffraction during various stages of evolution of microstructure. Here, the simulations elucidate the uncertain relation between spall strength and strain-rate and the much stronger relation between the spall strength and the temperatures generated due to laser shock loading for the small Cu sample dimensions considered here.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation and fracture characteristics of zirconium plate produced via ultrasonic additive manufacturing

Abstract The microstructural evolution, deformation modes, and fracture mechanisms of zirconium plate produced using ultrasonic additive manufacturing (UAM) are presented. In addition to conventional tensile testing techniques, digital image correlation captured highly variable strain accumulation in specimens loaded perpendicular or parallel to the build height (Z). When tested in parallel to Z, delamination at prior foil/foil interfaces creates strain localization noticeable in strain rate maps, whereas specimens loaded perpendicular to Z illustrate conventional strain hardening until necking accelerates delamination. Although bond strengths are statistically and spatially variable, in situ electron backscattering diffraction tests illustrate the ability for grains near interfaces to accommodate strain with twinning and slip modes consistent with conventionally produced zirconium alloys. Finally, mixtures of ductile and delamination-induced fracture highlight the interface-driven failure modes of UAM zirconium plate in the as-built condition. Graphic abstract

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Review of Medium-Mn, Low-Density Steels for Transportation Applications

Low-density steels constitute a broad and complex alloy space (Fe–Mn–Al–C) suitable for a variety of applications. In particular, there has been growing interest in duplex (ferrite + austenite) or multiphase (+ martensite, carbides) low-density steels as a lightweight, advanced high-strength steel (AHSS) for vehicle applications, spurred by extensive decarbonization efforts. Medium-Mn (med-Mn) (3 to 12 wt pct) steels with 3.5 to 10 wt pct Al additions have decreased densities, presenting an interesting opportunity for high-specific strength, intrusion-resistant, and energy-absorbing sheet components with reduced alloying contents compared to high-Mn grades like austenitic Fe–Mn–Al–C or twinning-induced plasticity steels. Compared to leaner med-Mn steels, the physical metallurgy of med-Mn, low-density steels (MMLS) is complex and distinguished by increased δ-ferrite fractions and austenite stacking fault energies, decreased martensite start temperatures, and modified phase transformation windows. Mechanical properties of MMLS are comparable to 3rd generation AHSS, attributable to the unique, multiphase microstructures, and the array of strengthening mechanisms that can be accessed. Despite this, challenges and unknowns remain with respect to their industrial implementation, and new processing routes may need to be developed. Here, this review aims to highlight the composition effects, processing methods, microstructural evolution, deformation behavior, and application properties geared toward manufacturing and performance, altogether assessing the potential of MMLS for transportation applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Scientific machine learning for modeling and simulating complex fluids

The formulation of rheological constitutive equations—models that relate internal stresses and deformations in complex fluids—is a critical step in the engineering of systems involving soft materials. While data-driven models provide accessible alternatives to expensive first-principles models and less accurate empirical models in many engineering disciplines, the development of similar models for complex fluids has lagged. The diversity of techniques for characterizing non-Newtonian fluid dynamics creates a challenge for classical machine learning approaches, which require uniformly structured training data. Consequently, early machine-learning based constitutive equations have not been portable between different deformation protocols or mechanical observables. Here, we present a data-driven framework that resolves such issues, allowing rheologists to construct learnable models that incorporate essential physical information, while remaining agnostic to details regarding particular experimental protocols or flow kinematics. These scientific machine learning models incorporate a universal approximator within a materially objective tensorial constitutive framework. By construction, these models respect physical constraints, such as frame-invariance and tensor symmetry, required by continuum mechanics. We demonstrate that this framework facilitates the rapid discovery of accurate constitutive equations from limited data and that the learned models may be used to describe more kinematically complex flows. This inherent flexibility admits the application of these “digital fluid twins” to a range of material systems and engineering problems. We illustrate this flexibility by deploying a trained model within a multidimensional computational fluid dynamics simulation—a task that is not achievable using any previously developed data-driven rheological equation of state.

Science & Technology - Other Topics↗
DOE OSTI2024

Additive Friction Stir Deposition of a Tantalum–Tungsten Refractory Alloy

Additive friction stir deposition (AFSD) is a solid-state metal additive manufacturing technique, which utilizes frictional heating and plastic deformation to create large deposits and parts. Much like its cousin processes, friction stir welding and friction stir processing, AFSD has seen the most compatibility and use with lower-temperature metals, such as aluminum; however, there is growing interest in higher-temperature materials, such as titanium and steel alloys. In this work, we explore the deposition of an ultrahigh-temperature refractory material, specifically, a tantalum–tungsten (TaW) alloy. The solid-state nature of AFSD means refractory process temperatures are significantly lower than those for melt-based additive manufacturing techniques; however, they still pose difficult challenges, especially in regards to AFSD tooling. In this study, we perform initial deposition trials of TaW using twin-rod-style AFSD with a high-temperature tungsten–rhenium-based tool. Many challenges arise because of the high temperatures of the process and high mechanical demand on AFSD machine hardware to process the strong refractory alloy. Despite these challenges, successful deposits of the material were produced and characterized. Mechanical testing of the deposited material shows improved yield strength over that of the annealed reference material, and this strengthening is mostly attributed to the refined recrystallized microstructure typical of AFSD. These findings highlight the opportunities and challenges associated with ultrahigh-temperature AFSD, as well as provide some of the first published insights into twin-rod-style AFSD process behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structure/property relationship of semicrystalline polymers during tensile deformation: a molecular dynamics approach

Molecular dynamics (MD) simulation with an ab initio numerical model is conducted to study the structure–property relationship of semicrystalline polymers during uniaxial deformation. The effects of chain length, temperature, and strain rate on mechanical properties are discussed. The influences of microstructural evolution such as bond length, entanglement density, and chain orientation are also studied quantitatively. The temperature will greatly affect the chain conformation in amorphous domains, and the results revealed that the interaction of amorphous and crystalline domains played a crucial role during stretching. Accordingly, the yielding of semicrystalline polymers follows different mechanisms at temperatures above and below T g . A melt-recrystallization scheme is observed during yielding at higher temperatures, while destruction of crystal structures is observed at lower temperatures at the yield point. The correlated effects of different temperatures and strain rates on mechanical properties are examined. This research is part of our efforts to develop a digital twin of a real experiment for efficient optimization of polymer material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Morphology, Deformations, and Photocatalytic Activity of Thermally Treated Brookite Titanium Dioxide Thin Films

Metastable states, in which the coupling between long-range lattice deformations and electronic properties can be controlled, provide a pathway to tailoring the behavior of photocatalytic materials by directing the flow of photoinduced charge carriers. Brookite is a metastable polymorph of earth-abundant TiO 2 that exhibits photocatalytic function and, due to its high energy relative to the anatase and rutile polymorphs, may serve as a precursor for the formation of transitional metastable structures. In this work, facile thermal annealing is employed to promote the formation of predominantly brookite-phase films, regulate the brookite lattice distortions, and determine the effect of these distortions on charge separation, ultimately directed at enhancing photocatalytic activity. Profile fitting of X-ray diffraction patterns and peak shifts in Raman spectra revealed structural distortions of the brookite lattice. Structural defects, including lattice gliding, dislocations, stacking faults, and twin boundaries, were observed using scanning transmission electron microscopy. First-principles simulations reveal how the lattice distortions associated with stacking faults induce band bending, thus increasing the photocatalytic activity of brookite. In conclusion, this study provides insight into the microstructural tuning of metastable phases to enhance their unique functionalities.

band bending↗
DOE OSTI2021

Bifunctional nanoprecipitates strengthen and ductilize a medium-entropy alloy

Single-phase high- and medium-entropy alloys with face-centred cubic (fcc) structure can exhibit high tensile ductility and excellent toughness, but their room-temperature strengths are low. Dislocation obstacles such as grain boundaries, twin boundaries, solute atoms and precipitates can increase strength. However, with few exceptions, such obstacles tend to decrease ductility. Interestingly, precipitates can also hinder phase transformations. Here, using a model, precipitate-strengthened, Fe–Ni–Al–Ti medium-entropy alloy, we demonstrate a strategy that combines these dual functions in a single alloy. The nanoprecipitates in our alloy, in addition to providing conventional strengthening of the matrix, also modulate its transformation from fcc-austenite to body-centred cubic (bcc) martensite, constraining it to remain as metastable fcc after quenching through the transformation temperature. During subsequent tensile testing, the matrix progressively transforms to bcc-martensite, enabling substantial increases in strength, work hardening and ductility. This use of nanoprecipitates exploits synergies between precipitation strengthening and transformation-induced plasticity, resulting in simultaneous enhancement of tensile strength and uniform elongation. Further, our findings demonstrate how synergistic deformation mechanisms can be deliberately activated, exactly when needed, by altering precipitate characteristics (such as size, spacing, and so on), along with the chemical driving force for phase transformation, to optimize strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the effect of refractory metal chemistry on the stacking fault energy and mechanical property of Cantor-based multi-principal element alloys

Multi-principal-element alloys (MPEAs) based on 3d-transition metals show remarkable mechanical properties. In this study, the stacking fault energy (SFE) in face-centered cubic (fcc) alloys is a critical property that controls underlying deformation mechanisms and mechanical response. Here, we present an exhaustive density-functional theory study on refractory- and copper-reinforced Cantor-based systems to ascertain the effects of refractory metal chemistry on SFE. We find that even a small percent change in refractory metal composition significantly changes SFEs, which correlates favorably with features like electronegativity variance, size effect, and heat of fusion. For fcc MPEAs, we also detail the changes in mechanical properties, such as bulk, Young's, and shear moduli, as well as yield strength. A Labusch-type solute-solution-strengthening model was used to evaluate the temperature-dependent yield strength, which, combined with SFE, provides a design guide for high-performance alloys. We also analyzed the electronic structures of two down-selected alloys to reveal the underlying origin of optimal SFE and strength range in refractory-reinforced fcc MPEAs. These new insights on tuning SFEs and modifying composition-structure-property correlation in refractory- and copper-reinforced MPEAs by chemical disorder, provide a chemical route to tune twinning- and transformation-induced plasticity behavior in fcc MPEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Review of the Serrated-Flow Phenomenon and Its Role in the Deformation Behavior of High-Entropy Alloys

High-entropy alloys (HEAs) are a novel class of alloys that have many desirable properties. The serrated flow that occurs in high-entropy alloys during mechanical deformation is an important phenomenon since it can lead to significant changes in the microstructure of the alloy. In this article, we review the recent findings on the serration behavior in a variety of high-entropy alloys. Relationships among the serrated flow behavior, composition, microstructure, and testing condition are explored. Importantly, the mechanical-testing type (compression/tension), testing temperature, applied strain rate, and serration type for certain high-entropy alloys are summarized. The literature reveals that the serrated flow can be affected by experimental conditions such as the strain rate and test temperature. Furthermore, this type of phenomenon has been successfully modeled and analyzed, using several different types of analytical methods, including the mean-field theory formalism and the complexity-analysis technique. Importantly, the results of the analyses show that the serrated flow in HEAs consists of complex dynamical behavior. It is anticipated that this review will provide some useful and clarifying information regarding the serrated-flow mechanisms in this material system. Finally, suggestions for future research directions in this field are proposed, such as the effects of irradiation, additives (such as C and Al), the presence of nanoparticles, and twinning on the serrated flow behavior in HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid grain refinement and compositional homogenization in a cast binary Cu50Ni alloy achieved by friction stir processing

Friction stir processing (FSP) has been increasingly adopted for joining and processing materials in automotive, aerospace and industrial construction. During FSP a dynamic competition between high-speed shear deformation and deformation-induced heating brings about a complex competition between multiple dynamic microstructural evolution mechanisms making it difficult to predict the microstructural evolution pathway. Hence, improved understanding of microstructural evolution mechanisms during FSP can be beneficial for continued growth in the adoption of FSP for demanding applications of future. Towards this goal, this study uses a model binary Cu – 50 at.% Ni alloy to clarify the effect of single and double pass FSP on the microstructural evolution of a coarse grained and compositionally heterogeneous cast microstructure. High energy synchrotron X-ray diffraction, electron backscatter diffraction, and nanoindentation are used to clarify the microstructural evolution due to FSP. The process of compositional homogenization of as-cast segregations is studied by energy dispersive spectroscopy and atom probe tomography. Our results show that a single fast FSP pass at 30 mm.s -1 produces a 100 µm deep layer of submicrometric and hall-petch hardened CuNi grains. The initial cast compositional heterogeneities in a micrometric scale is rapidly transformed to nano-sized domains, mainly confined at grain boundaries. Double pass FSP increases the penetration depth of the processed layer and leads to a 2.9 times grain growth relative to single pass FSP. Grain fragmentation, discontinuous dynamic recrystallization, grain growth, and twinning mechanisms are discussed. In conclusion, these results highlight the value of FSP for ultrafast grain refinement and compositional homogenization of cast alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Identification of crystal plasticity model parameters by multi-objective optimization integrating microstructural evolution and mechanical data

Crystal plasticity models evolve a polycrystalline yield surface using meso-scale descriptions of deformation mechanisms. The activation of deformation mechanisms is governed by crystallography and a set of model parameters, which are typically calibrated through the fitting of mechanical data such as stress–strain curves and elastic lattice strains. Microstructural data such as phase fractions and texture evolution are used for verifying crystal plasticity parameters. In this study, we use a multi-objective genetic algorithm to identify hardening parameters from flow stress curves with an option to incorporate texture into the optimization approach. Robust, generalized objective functions are developed and used to identify sets of parameters pertaining to dislocation density-based hardening laws in visco-plastic and elasto-plastic self-consistent (VPSC and EPSC) homogenization models. First, the parameters are identified for pure Nb directly from texture using an objective function based on generalized spherical harmonics. Since texture evolution is driven by the relative contribution of active slip systems, the parameters governing the evolution of slip resistance ratios can be recovered from fitting discrete textures at a series of strains. Next, a comprehensive set of load reversal data for dual phase (DP) 780 steel is used to fit a hardening law and a back-stress law in EPSC. Finally, parameters pertaining to a complex hardening law for the evolution of slip and twinning in pure α-Ti are identified. Remarkably, using texture as an objective in combination with stress–strain objectives constrains the model of Ti to fully reproduce not only stress–strain and texture evolution but also hierarchical twinning measurements as a function of initial grain size and texture. Furthermore, given an appropriate model fit to representative experimental texture evolution, underlying twin volume fractions contributing to texture evolution can be predicted.

42 ENGINEERING↗
DOE OSTI2025

Direct observations of transient weakening during phase transformations in quartz and olivine

Phase transformations are widely invoked as a source of rheological weakening during subduction, continental collision, mantle convection and various other geodynamic phenomena. However, despite more than half a century of research, the likelihood and magnitude of such weakening in nature remain poorly constrained. Here we use experiments performed on a synchrotron beamline to reveal transient weakening of up to three orders of magnitude during the polymorphic quartz to coesite (SiO 2 ) and olivine to ringwoodite (Fe 2 SiO 4 ) phase transitions. Weakening becomes increasingly prominent as the transformation outpaces deformation. We suggest that this behaviour is broadly applicable among silicate minerals undergoing first-order phase transitions and examine the likelihood of weakening due to the olivine-spinel, (Mg,Fe) 2 SiO 4 , transformation during subduction. Modelling suggests that cold, wet slabs are most susceptible to transformational weakening, consistent with geophysical observations of slab stagnation in the mantle transition zone beneath the western Pacific. In conclusion, our study highlights the importance of incorporating transformational weakening into geodynamic simulations and provides a quantitative basis for doing so.

Cross, Andrew J. [Woods Hole Oceanographic Institu↗
DOE OSTI2025

Microstructure Clones

Background: A material’s microstructure drives its material performance. Contemporary crystal plasticity experiments compare full-field strain measurements of polycrystal specimens to models. Because each specimen is unique, it is impossible to know which features of the observed deformation are deterministic vs statistical; thus, differences between model and experiment may or may not be significant. Objective: This paper introduces the invention of microstructure clones. Microstructure clones are 2D oligocrystal specimens that have nearly identical microstructures to remedy the aforementioned experimental limitations. Having specimens with nearly identical microstructures will allow for multiple destructive tests of a microstructure (either as repeats or intentionally different experiments), an ability to “see the future” by providing insight into how a specimen will deform, variability quantification, and experimental investigations of response to small microstructural changes. Methods: This work introduces microstructure clones. Repeatability of these clones is demonstrated in tensile bars of pure nickel. Local strain measurements from digital image correlation are compared between clone specimens and compared to results from a crystal plasticity finite element model. Results: Two sets of microstructure clones were tested in this study and displayed very consistent deformation responses within each clone set. Small observed differences in deformation invite investigation into microstructure stochasticity and the effect of small microstructural and loading differences. Conclusions: Microstructure clones represent a significant shift in understanding structure–property relationships. This work reshapes experimental crystal plasticity to allow for experiments that control for specific variables, quantification of microstructural stochasticity (and other sources of stochasticity), and opportunities for replicating experiments.

Crystal Plasticity↗
DOE OSTI2026

Multiple valence-space and core-excited band terminations in Ho and Er isotopes

High-spin structures of holmium (𝑍 = 67) and erbium (𝑍 = 68) isotopes are presented near mass 160, a region where collective and single-particle modes of excitation compete in the generation of angular momentum at the highest experimentally attainable spins in atomic nuclei. The level schemes of the 156,157,158 Ho isotopes have been significantly extended, reaching spins in the 40⁢ℏ to 55⁢ℏ range, through multiple experiments utilizing the Gammasphere spectrometer. In particular, several new noncollective band-terminating states are reported for these nuclei. The nature of these states, including both valence-space terminations and core-excited oblateconfigurations, is discussed in terms of proton particle-hole (p-h) excitations across the semimagic 𝑍 = 64 shell closure. Cranked-Nilsson–Strutinsky (CNS) calculations have been used to interpret the nature of these noncollective states. The corresponding terminating states in 154–159 Er are also included, providing a systematic description of band termination in this mass region. In addition, three weak rotational structures have been assigned to 157 Ho at the highest spins. These collective bands are proposed to be based on a triaxial strongly deformed nuclear shape, involving neutron p-h excitations across the 𝑁 = 82 shell gap.

150 ≤ A ≤ 189↗