Search NASA⌕ Search

SEARCH · Search NASA

Results for “directed graphs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

The turbulent boundary layer on a porous plate - Experimental heat transfer with uniform blowing and suction, with moderately strong acceleration.

Experimental data are presented for heat transfer to the turbulent boundary layer subjected to transpiration and acceleration at constant values of the acceleration parameter K of approximately .00000145. This is a moderately strong acceleration, but not so strong as to result in laminarization of the boundary layer. The results for transpiration fractions F of -0.002, 0.0, and +0.0058 are presented in detail in tabular form, and in graphs of Stanton number versus enthalpy thickness Reynolds number. In addition, temperature profiles at several stations are presented. Stanton number results for F = -0.004, +0.002, and +0.004 are also presented, but in graphical form only. The data were obtained using air as both the free-stream and the transpired fluid, at relatively low velocities, and with temperature differences sufficiently low so that the influence of temperature-dependent fluid properties is minimal. All data were obtained with the surface maintained at a temperature invariant in the direction of flow.

Thielbahr, W. H.↗

The Measurement of Fuel-Air Ratio by Analysis for the Oxidized Exhaust Gas

An investigation was made to determine a method of measuring fuel-air ratio that could be used for test purposes in flight and for checking conventional equipment in the laboratory. Two single-cylinder test engines equipped with typical commercial engine cylinders were used. The fuel-air ratio of the mixture delivered to the engines was determined by direct measurement of the quantity of air and of fuel supplied and also by analysis of the oxidized exhaust gas and of the normal exhaust gas. Five fuels were used: gasoline that complied with Army-Navy fuel Specification No. AN-VV-F-781 and four mixtures of this gasoline with toluene, benzene, and xylene. The method of determining the fuel-air ratio described in this report involves the measurement of the carbon-dioxide content of the oxidized exhaust gas and the use of graphs for the presented equation. This method is considered useful in aircraft, in the field, or in the laboratory for a range of fuel-air ratios from 0.047 to 0.124.

Gerrish, Harold C.↗

The Measurement of Fuel-air Ratio by Analysis of the Oxidized Exhaust Gas

An investigation was made to determine a method of measuring fuel-air ratio that could be used for test purposes in flight and for checking conventional equipment in the laboratory. Two single-cylinder test engines equipped with typical commercial engine cylinders were used. The fuel-air ratio of the mixture delivered to the engines was determined by direct measurement of the quantity of air and of fuel supplied and also by analysis of the oxidized exhaust gas and of the normal exhaust gas. Five fuels were used: gasoline that complied with Army-Navy Fuel Specification, No. AN-VV-F-781 and four mixtures of this gasoline with toluene, benzene, and xylene. The method of determining the fuel-air ratio described in this report involves the measurement of the carbon-dioxide content of the oxidized exhaust gas and the use of graphs or the presented equation. This method is considered useful in aircraft, in the field, or in the laboratory for a range of fuel-air ratios from 0.047 to 0.124

FUELS-TOLUENE↗

The design of an intelligent human-computer interface for the test, control and monitor system

The graphical intelligence and assistance capabilities of a human-computer interface for the Test, Control, and Monitor System at Kennedy Space Center are explored. The report focuses on how a particular commercial off-the-shelf graphical software package, Data Views, can be used to produce tools that build widgets such as menus, text panels, graphs, icons, windows, and ultimately complete interfaces for monitoring data from an application; controlling an application by providing input data to it; and testing an application by both monitoring and controlling it. A complete set of tools for building interfaces is described in a manual for the TCMS toolkit. Simple tools create primitive widgets such as lines, rectangles and text strings. Intermediate level tools create pictographs from primitive widgets, and connect processes to either text strings or pictographs. Other tools create input objects; Data Views supports output objects directly, thus output objects are not considered. Finally, a set of utilities for executing, monitoring use, editing, and displaying the content of interfaces is included in the toolkit.

Shoaff, William D.↗

DSMC calculations for the delta wing

Results are reported from three-dimensional direct simulation Monte Carlo (DSMC) computations, using a variable-hard-sphere molecular model, of hypersonic flow on a delta wing. The body-fitted grid is made up of deformed hexahedral cells divided into six tetrahedral subcells with well defined triangular faces; the simulation is carried out for 9000 time steps using 150,000 molecules. The uniform freestream conditions include M = 20.2, T = 13.32 K, rho = 0.00001729 kg/cu m, and T(wall) = 620 K, corresponding to lambda = 0.00153 m and Re = 14,000. The results are presented in graphs and briefly discussed. It is found that, as the flow expands supersonically around the leading edge, an attached leeside flow develops around the wing, and the near-surface density distribution has a maximum downstream from the stagnation point. Coefficients calculated include C(H) = 0.067, C(DP) = 0.178, C(DF) = 0.110, C(L) = 0.714, and C(D) = 1.089. The calculations required 56 h of CPU time on the NASA Langley Voyager CRAY-2 supercomputer.

Celenligil, M. Cevdet↗

Turbulent magnetic reconnection

The results of two-dimensional spectral-method MHD simulations of the effect of turbulence on magnetic-reconnection processes are presented in extensive graphs and tables and characterized in detail. In a periodic sheet-pinch configuration, early-onset, persistent turbulence is found to occur when a low level of broadband fluctuations is introduced into the initial data. Features observed include small-scale unsteady coherent electric-current and vorticity structures, enhanced viscous and resistive dissipation, unsteady and spatially asymmetric fluid flow, large-scale and small-scale magnetic islands, multiple X points, large-amplitude electric-field fluctuations, and spectral characteristics indicating that the turbulence is broadband in both spatial directions and similar to homogeneous MHD turbulence. The importance of reconnection for studies of solar, magnetospheric, and laboratory plasmas in inhomogeneous magnetic fields is indicated.

Matthaeus, W. H.↗

Models of polarized infrared emission from bipolar nebulae

Many stars with circumstellar dust shells show a high degree of linear polarization (Sato et al. 1985). We are developing a model which assumes that the polarization arises from scattering by circumstellar dust. Our model assumes a geometry in which the star is surrounded by an optically thin spherical dust shell and embedded within an optically thick disk. This geometry is consistent with that proposed for objects with bipolar molecular outflow. This is important because many bipolar flow objects have also been observed to be highly polarized. The high degree of linear polarization is produced because the disk differentially attenuates the light from the star. The light incident from the point source is attenuated by a factor of exp(-tau/cos theta) where theta is the angle between a ray from the point source to the scatterer and a ray normal to the disk; tau is the optical depth at the wavelength of interest. Hence, the light scattered from the regions directly above and below the disk give the largest contribution to the total flux. The scattering angle for light from these regions is near 90 deg., so the light is strongly polarized and, in the Rayleigh scattering regime, is polarized parallel to the disk. The Stokes parameters for the scattered light from each particle in the shell are calculated by using the scattering matrix elements generated by a Mie scattering program. After the Stokes parameters for each particle are computed they are summed to give the Stokes parameters for the entire shell. Two graphs are presented which show the intensity and polarization spectrum generated by our model using the optical constants for astronomical silicates as defined by Draine and Lee (1984).

Burns, M. S.↗

Scientific data visualization software - Trends and directions

Scientific data visualization has finally come of age as an important and accepted discipline. While scientists have been using computer graphics to visualize experimental data and computational results for at least 30 years, recent improvements in cost/performance of graphics workstations, more readily available software, and a new-found identity based on the report "Visualization in Scientific Computing" (McCormick, DeFanti, and Brown, 1987) have solidified the discipline. The thesis here is that scientists are forced to work too hard to create these visualizations, but that the evolving set of visualization tools can greatly reduce the requisite effort. The architecture of a new class of software can lead to a more widespread availability of interactive visualization tools, which can make the process of creating a visualization as simple as doing interactive chart and graph layout.

Foley, James D.↗

Resonant geomagnetic field oscillations and Birkeland currents in the morning sector

The relationship between large-scale Birkeland currents and resonant oscillations of the geomagnetic field is investigated on the basis of Viking magnetic-field, electric-field, and particle measurements and AMPTE-CEE and IMP-8 magnetic-field measurements obtained during April 23-25, 1986. The data are presented in extensive graphs and characterized in detail. The 3-16-mHz 5-60-nT magnetic-field oscillations detected by Viking are also seen by AMPTE-CEE below L = 8.8 and extend from the lower L shells to the boundary between regions 1 and 2 of the Birkeland-current system, and this boundary is shown to be closely related to the interface between the low-latitude boundary layer and the central plasma sheet. It is suggested that the magnetospheric oscillations may be driven by several different solar-wind features, possibly depending on the direction of the IMF.

Potemra, T. A.↗

Optical surface refurbishment in space environment

The potential use of the vacuum environment of space to clean contaminated mirror surfaces or generate Al mirror surfaces with high reflectance in the 80-200-nm region is discussed and illustrated with diagrams and graphs, reviewing previous studies and current experiment proposals. Consideration is given to (1) applying the atomic oxygen plasma environment of LEO to clean coated mirrors and (2) depositing freshly evaporated Al onto a mirror surface in vacuum, providing relatively long periods of high EUV reflectance before oxidation of the surface degrades performance: such a procedure could be performed as a maintenance measure or even incorporated into the design of a space observatory. A free-flying experiment is described which would produce and maintain an Al surface with controlled exposure to OH, H2O, and O2; demonstrate directed-beam Al deposition onto a simulated telescope/spectrometer surface; monitor instrument reflectance/sensitivity over time; and demonstrate in situ refurbishment of the degraded surface.

Heaney, James B.↗

Wide Range SET Pulse Measurement

A method for measuring a wide range of SET pulses is demonstrated. Use of dynamic logic, faster than ordinary CMOS, allows capture of short pulses. A weighted binning of SET lengths allows measurement of a wide range of pulse lengths with compact circuitry. A pulse-length-conservative pulse combiner tree routes SETs from combinational logic to the measurement circuit, allowing SET measurements in circuits that cannot easily be arranged in long chains. The method is applied to add-multiplex combinational logic, and to an array of NFET routing switches, at .35 micron. Pulses are captured in a chain of Domino Logic AND gates. Propagation through the chain is frozen on the trailing edge by dropping low the second "enable" input to the AND gates. Capacitive loading is increased in the latter stages to create an approximately logarithmic weighted binning, so that a broad range of pulse lengths can be captured with a 10 stage capture chain. Simulations show pulses can be captured which are 1/5th the length of those typically captured with leading edge triggered latch methods, and less than the length of those captured with a trailing edge latch method. After capture, the pulse pattern is transferred to an SEU protected shift register for readout. 64 instances of each of two types of logic are used as targets. One is a full adder with a 4 to 1 mux on its inputs. The other is a 4 x 4 NFET routing matrix. The outputs are passed through buffered XNOR comparators to identify pulses, which are merged in a buffered not-nand (OR) tree designed to avoid pulse absorption as much as possible. The output from each of the two test circuits are input into separate pulse measurement circuits. Test inputs were provided so that the circuit could be bench tested and calibrated. A third SET measurement circuit with no inputs was used to judge the contribution from direct hits on the measurement circuit. Heavy ions were used with an LET range from 12 to 176. At LET of 21 and below, the very small number of SETs were not significantly higher in the test over the control circuits. At higher LET the test circuit SETs are one or two orders of magnitude greater than for the control circuit. The NFET circuit produces more and slightly longer SETs as expected. But the differences do not appear to be significant enough to modify strategies now used to avoid capture of SETs in chips such as FPGAs. Complete data and graphs will be in the full paper / presentation. In the summary figure below left, NOCL is the reference circuit without any input, and number of stages triggered is plotted. Simulation at right shows the smallest pulse captured (stage 2) at about 300 ps. Our conclusion is that the method is promising, but that improvements in the merge network are desirable before applying in a deep submicron process

Shuler, Robert L.↗

Computation of rarefied hypersonic flows

Numerical techniques for the simulation of hypersonic flows of rarefied gases are examined in an analytical review. The direct-simulation Monte Carlo (DSMC) method developed to interpret measurement data obtained by the Space Shuttle in the SUMS project is described; the fundamental limitations of the DMSC approach are discussed; and modifications to improve the physical plausibility of DSMC predictions are proposed. Particular attention is given to the use of a double-peaked molecular distribution function for the internal flow in the SUMS probe, a downstream vacuum-reservoir condition as a simplifying assumption, and an explicit forward-time centered-space differencing scheme for the discretization of the SUMS problem. Typical simulation results are presented in extensive graphs and briefly characterized.

Cheng, Sin-I↗

Gamma-ray bursters

Current theoretical models developed to explain the observational data (from spaceborne detectors) on gamma-ray bursters are summarized and illustrated with drawings, diagrams, graphs, and photographic images. Although the data are fragmentary and often flawed by instrument defects, models involving neutron stars with strong magnetic fields are generally favored, and it is assumed that most observed bursters lie within the Galaxy. The neutron-star origin of the bursts is suggested by their intensity and rapid variability (implying a very compact high-energy source) and the presence in some burster spectra of a line at 420 keV which is explained by the combination of electron-positron annihilation and gravitational reddening. Consideration is also given to optical flashes observed to occur about once per year in the direction of gamma bursters, and the need for further searches for lower-energy emissions from bursters is stressed.

Schaefer, B. E.↗

Hydrological Modeling of the Jezero Crater Outlet-Forming Flood

Abundant evidence exists for lakes on Mars both from orbital observations [e.g., 1-3] and in situ exploration [e.g., 4-5]. These lakes can be divided into two classes: those that were hydrologically closed, so their source valley(s) terminated at the basin [3], and those that were hydrologically open, where there was sufficient flow from inlet valley(s) to cause the lake to breach and form an outlet valley [2]. It is easier to be confident from orbital data alone that a standing body of water must have existed in open basins, because there is no other way for their perched outlet valleys to form. The majority of basins fed by valley networks, rather than by isolated inlet valleys, are open [6], with some important exceptions (e.g., Gale Crater). Jezero crater (Fig. 1) is one of the most well-studied open basin paleolakes on Mars, with a breach that re-mains well above the lowest part of the crater floor, and two sedimentary fans at its northwestern margin that are likely deltaic in origin [7-9]. CRISM observations of these sediments indicate they host a variety of alteration minerals [9-11], including smectite and carbonate, and both the mineralogy of the sediments and their settings suggest they have a strong potential for preserving organic materials [10]. As a result, Jezero is a strong candidate landing site for the Mars 2020 rover. Approximate formative discharges have been estimated for its well-preserved western fan (Q approximately 500m3/s) [7], but to our knowledge, no estimates for the dis-charges associated with formation and incision of its outlet valley have been presented. Indeed, only a few studies [e.g., 12-14] have attempted to reconstruct the formation of outlet breaches broadly similar to Jezero anywhere on Mars, despite the apparent commonality of basins with large outlets [e.g., 2]. The outlet valley formed as a dam breach when the lake overflowed. In such an event, the growth and incision of the breach is directly coupled to flood discharge. In the case of Jezero, the discharge through the breach eventually lacked the energy needed to erode through the dam further, preventing complete drainage of the lake. After the initial flood, further incision can take place if additional water flows into, and thus out of, the hydrologically open lake, though the rate of this erosion occurs under more typical fluvial conditions. Despite this qualitative understanding of the process, it is useful to explore numerically what range of model parameters are potentially consistent with obser-vations of the outlet. We ultimately seek to address questions that include: (1) What was the flood hydro-graph?, (2) What sediment transport processes were involved and what can we infer about the erosion process? (3) Can most or all of the Jezero outlet's morphology be explained as a consequence of catastrophic formation, or is additional longer-term erosion required?

geology↗

The elemental and isotopic composition of galactic cosmic ray nuclei

A directly accessible sample of matter which originates outside the solar system is provided by galactic cosmic rays. The present investigation is primarily concerned with progress related to questions raised regarding the similarity or difference between solar system matter and matter coming from outside the solar system. The investigation takes into account U.S. contributions to this topic over the period from 1979 to 1982. The cosmic ray (CR) abundances of all the elements from H to Ni (atomic number Z=1 to 28) have now been measured. Cosmic ray source (CRS) and solar system (SS) elemental compositions are listed in a table, and the ratio of CRS to SS abundance for 21 elements is shown in a graph. There is now clear evidence from CR isotope studies that the nucleosynthesis of CRS material has differed from that of SS material.

Mewaldt, R. A.↗

Advanced Communications Architecture Demonstration Made Significant Progress

Simulation for a ground station located at 44.5 deg latitude. The Advanced Communications Architecture Demonstration (ACAD) is a concept architecture to provide high-rate Ka-band (27-GHz) direct-to-ground delivery of payload data from the International Space Station. This new concept in delivering data from the space station targets scientific experiments that buffer data onboard. The concept design provides a method to augment the current downlink capability through the Tracking Data Relay Satellite System (TDRSS) Ku-band (15-GHz) communications system. The ACAD concept pushes the limits of technology in high-rate data communications for space-qualified systems. Research activities are ongoing in examining the various aspects of high-rate communications systems including: (1) link budget parametric analyses, (2) antenna configuration trade studies, (3) orbital simulations (see the preceding figure), (4) optimization of ground station contact time (see the following graph), (5) processor and storage architecture definition, and (6) protocol evaluations and dependencies.

Carek, David Andrew↗

Growth Curve Parameterization of Metabolic Activity of Yeast Cells for BioSentinel

The goal of the BioSentinel small satellite payload is to measure the effect of deep space radiation on the growth and metabolic activity of yeast cells. Raw test data is generated by fluidics cards containing yeast cells rehydrated at different periods, with metabolic activity measured by the reduction of alamarBlue. Each card well has a sensor array that measures the amount of red, green, and infrared light transmitted through the yeast culture. This illumination data is then converted to absorbance values, which are further converted into concentrations. The ultimate objective is to convert these concentrations into biologically-relevant metrics that can be compared against one another to determine changes due to differential radiation exposure. Beginning with IR absorbance data (corresponding to cell density) from ground studies, three parameters from a sigmoidal growth curve were extracted and analyzed: 𝜆 (lag phase), 𝜇 (max growth rate), and A (max cell growth). The data was fit to the Gompertz model of microbial growth using non-linear regression (Minitab), as the fit error was reduced compared to the simpler logistic growth curve. Graphs showed that the data contained a discrepancy (drift) in the lag phase that is attributable to a slow, constant loss of moisture. Correcting this discrepancy by fitting the first 25 hours of the data to a power function and subtracting these values from the absorbance readings obtained a better statistical fit to the growth curve in the lag phase. A power fit was selected over a linear fit because it reflected the effects of constant volume loss. This correction to the BioSentinel data analysis pipeline will enable quantitative statistical analysis of the effect of different levels of deep space radiation on yeast cells. Future work includes automation of drift correction and curve modeling to extract these parameters directly from data.

Growth Curve↗

NASA Tech Briefs, April 2009

Topics covered include: Direct-Solve Image-Based Wavefront Sensing; Use of UV Sources for Detection and Identification of Explosives; Using Fluorescent Viruses for Detecting Bacteria in Water; Gradiometer Using Middle Loops as Sensing Elements in a Low-Field SQUID MRI System; Volcano Monitor: Autonomous Triggering of In-Situ Sensors; Wireless Fluid-Level Sensors for Harsh Environments; Interference-Detection Module in a Digital Radar Receiver; Modal Vibration Analysis of Large Castings; Structural/Radiation-Shielding Epoxies; Integrated Multilayer Insulation; Apparatus for Screening Multiple Oxygen-Reduction Catalysts; Determining Aliasing in Isolated Signal Conditioning Modules; Composite Bipolar Plate for Unitized Fuel Cell/Electrolyzer Systems; Spectrum Analyzers Incorporating Tunable WGM Resonators; Quantum-Well Thermophotovoltaic Cells; Bounded-Angle Iterative Decoding of LDPC Codes; Conversion from Tree to Graph Representation of Requirements; Parallel Hybrid Vehicle Optimal Storage System; and Anaerobic Digestion in a Flooded Densified Leachbed.

Source record↗