Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation loops”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Calculation of Radiation Damage in SLAC Targets

Ti-6Al-4V alloys are being considered as a positron producing target in the Next Linear Collider, with an incident photon beam and operating temperatures between room temperature and 300 C. Calculations of displacement damage in Ti-6Al-4V alloys have been performed by combining high-energy particle FLUKA simulations with SPECTER calculations of the displacement cross section from the resulting energy-dependent neutron flux plus the displacements calculated from the Lindhard model from the resulting energy-dependent ion flux. The radiation damage calculations have investigated two cases, namely the damage produced in a Ti-6Al-4V SLAC positron target where the irradiation source is a photon beam with energies between 5 and 11 MeV. As well, the radiation damage dose in displacements per atom, dpa, has been calculated for a mono-energetic 196 MeV proton irradiation experiment performed at Brookhaven National Laboratory (BLIP experiment). The calculated damage rate is 0.8 dpa/year for the Ti-6Al-4V SLAC photon irradiation target, and a total damage exposure of 0.06 dpa in the BLIP irradiation experiment. In both cases, the displacements are predominantly ({approx}80%) produced by recoiling ions (atomic nuclei) from photo-nuclear collisions or proton-nuclear collisions, respectively. Approximately 25% of the displacement damage results from the neutrons in both cases. Irradiation effects studies in titanium alloys have shown substantial increases in the yield and ultimate strength of up to 500 MPa and a corresponding decrease in uniform ductility for neutron and high energy proton irradiation at temperatures between 40 and 300 C. Although the data is limited, there is an indication that the strength increases will saturate by doses on the order of a few dpa. Microstructural investigations indicate that the dominant features responsible for the strength increases were dense precipitation of a {beta} (body-centered cubic) phase precipitate along with a high number density of dislocation loops.

42 ENGINEERING↗

Influence of interfacial dislocations on hysteresis loops of ferroelectric films

We investigated the influence of dislocations, located at the interface of a ferroelectric film and its underlying substrate, on the ferroelectric hysteresis loop including the remanent polarization and coercive field using phase-field simulations. We considered epitaxial ferroelectric BaTiO3 films and found that the hysteresis loop is strongly dependent on the type and density of interfacial dislocations. The dislocations that stabilize multiple ferroelectric variants and domains reduce the coercive field, and consequently, the corresponding remanent polarization also decreases.

36 MATERIALS SCIENCE↗

Dissociated prismatic loop punching by bubble growth in FCC metals

Abstract Materials performance can be significantly degraded due to bubble generation. In this work, the bubble growth process is elaborated in Cu by atomistic modeling to bridge the gap of experimental observations. Upon continuous He implantation, bubble growth is accommodated first by nucleation of dislocation network from bubble surface, then formation of dissociated prismatic dislocation loop (DPDL), and final DPDL emission in $$\langle 110\rangle$$ ⟨ 110 ⟩ directions. As the DPDL is found capable of collecting He atoms, this process is likely to assist the formation of self-organized bubble superlattice, which has been reported from experiments. Moreover, the pressurized bubble in solid state manifests the shape of an imperfect octahedron, built by Cu $$\{111\}$$ { 111 } surfaces, consistent with experiments. These atomistic details integrating experimental work fill the gap of mechanistic understanding of athermal bubble growth in Cu. Importantly, by associating with nanoindentation testings, DPDL punching by bubble growth arguably applies to various FCC (face-centered cubic) metals such as Au, Ag, Ni, and Al.

36 MATERIALS SCIENCE↗

Dynamic observations of heavy-ion damage in Fe and Fe-Cr alloys.

We give an overview and summary of recent in-situ heavy-ion irradiation experiments on Fe and Fe-Cr alloys carried out on the Argonne IVEM Facility at irradiation temperatures up to 500 C. Several new and unexpected observations were made. At low doses the contrast of new irradiation-induced dislocation loops sometimes developed over time intervals as long as 0.2 s, many orders of magnitude longer than expected for a process of cascade collapse. In addition at temperatures {le} 300 C, 'hopping' of 1/2<111> loops was induced by the ion or electron beams, especially in UHP Fe. At high doses complex microstructures developed in all materials, involving the formation of large interstitial loops. At 300 C and RT these loops had Burgers vectors of type b = 1/2<111> and large shear components. At 500 C only edge loops with b = <100> were produced.

36 MATERIALS SCIENCE↗

Investigation of dopant clustering and segregation to defects in semiconductors using atom probe tomography

The role of atom probe tomography in the investigation of clustering and segregation of dopants to lattice defects in semiconductors is highlighted on the basis of some selected salient illustrations obtained at the Groupe de Physique des Matériaux of Rouen (France). The instrument is shown to be able to map out the 3D distribution of chemical species in the three dimensions of space at the ultimate scale. Results related to clustering, segregation of dopants (As, B, and P) to grain boundaries, dislocation loops, and extended defects in silicon are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Atomic-scale mechanisms of void strengthening in tungsten

Neutron and heavy-ion irradiation of tungsten produces nanometer-size vacancy voids, gas-filled bubbles and dislocation loops. These defect features can affect mechanical properties and the impact can be quite significant because of their high density. Understanding the basic mechanisms of mechanical properties degradation is necessary for predicting radiation effects. Predictions can be made using discrete dislocation dynamics or/and finite element approaches which, however, need local interaction mechanisms as inputs. Such knowledge can be provided only by atomic-scale modeling. This paper reports the results of an extensive atomic-scale modeling study of the interactions between moving edge dislocations and voids in tungsten. Furthermore, the main focus is on the effects of the void size and ambient temperature. Critical resolved shear stress was calculated for voids up to 9 nm in diameter. Atomistic results are compared with the theoretical approach and with those obtained earlier for voids in body centered cubic (bcc) iron. An important role of the void surface has been revealed.

36 MATERIALS SCIENCE↗

Characterisation of radiation damage in W and W-based alloys from 2MeV self-ion near-bulk implantations

The displacement damage induced in bulk W and W-5 wt.% Re and W-5 wt.% Ta alloys by 2 MeV W + irradiation to doses 3.3×10 17 - 2.5×10 19 W + /m 2 at temperatures ranging from 300 to750°C has been characterized by transmission electron microscopy. An automated sizing and counting approach based on Image J has been proposed and performed for all irradiation data. In all cases the damage comprised dislocation loops, mostly of interstitial type, with Burgers vectors b = ½<111> (> 60%) and b = <100>. The diameters of loops did not exceed 20 nm, with the majority being ≤ 6 nm. The loop number density varied between 10 22 and 10 23 loops/m 3 . With increasing irradiation temperature, the loop size distributions shifted towards larger sizes, and there was a substantial decrease in loop number densities. The damage microstructure was less sensitive to dose than to temperature. Under the same irradiation conditions, loop number densities in the alloys were higher than in pure W but loops were smaller. In grains with normals close to z = <001>, loop strings developed in W at temperatures ≥ 500°C and doses ≥ 1.2 dpa, but such strings were not observed in the W-Re or W-Ta alloys. However, in other grain orientations complex structures appeared in all materials and dense dislocation networks formed at higher doses.

36 MATERIALS SCIENCE↗

Three-dimensional imaging of dislocations by X-ray diffraction laminography

Synchrotron radiation laminography with X-ray diffraction contrast enables three-dimensional imaging of dislocations in monocrystalline wafers. We outline the principle of the technique, the required experimental conditions, and the reconstruction procedure. The feasibility and the potential of the method are demonstrated by three-dimensional imaging of dislocation loops in an indent-damaged and annealed silicon wafer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The temperature dependence of heavy-ion damage in iron: a microstructural transition at elevated temperatures.

A transition is reported in the dislocation microstructure of pure Fe produced by heavy-ion irradiation of thin foils, which took place between irradiation temperatures (T{sub irr}) of 300 C and 500 C. At T{sub irr} {le} 400 C, the microstructure was dominated by round or irregular non-edge dislocation loops of interstitial nature and with Burgers vectors b = 1/2 111, although interstitial 100 loops were also present; at 500 C only rectilinear pure-edge 100 loops occurred. At intermediate temperatures there was a gradual transition between the two types of microstructure. At temperatures just below 500 C, mobile 111 loops were seen to be subsumed by sessile 100 loops. A possible explanation of these observations is given.

36 MATERIALS SCIENCE↗

Internal Electric Field Investigations of a Cadmium Zinc Telluride Detector Using Synchrotron X-ray Mapping and Pockels Effect Measurements

Cadmium zinc telluride (CZT) has remained a major focus of research due to its promising application as a room-temperature nuclear radiation detector material. Among the several parameters that substantially affect the detectors' performance, an important one is the distribution of the internal electric field. Brookhaven National Laboratory (BNL) employed synchrotron x-ray microscale mapping and measurements of the Pockels effect to investigate the distribution of the internal electric field in a CZT strip detector. Direct evidence that dislocations can distort the internal electric field of the detector was obtained. Furthermore, it was found that 'star' defects in the CZT crystal, possibly ascribed to dislocation loop punching, cause charge trapping.

43 PARTICLE ACCELERATORS↗

Ultrahigh strain-rate bending of copper nanopillars with laser-generated shock waves

An experimental study to bend FIB-prepared cantilevered single crystal Cu nanopillars of several hundred nanometers in diameter and length at ultrahigh strain rate is presented. The deformation is induced by laser-generated stress waves, resulting in local strain rates exceeding 10{sup 7} s{sup −1}. Loading of nano-scale Cu structures at these extremely short loading times shows unique deformation characteristics. At a nominal stress value of 297 MPa, TEM examination along with selected area electron diffraction characterization revealed that twins within the unshocked Cu pillars interacted with dislocations that nucleated from free surfaces of the pillars to form new subgrain boundaries. MD simulation results were found to be consistent with the very low values of the stress required for dislocation activation and nucleation because of the extremely high surface area to volume ratio of the nanopillars. Specifically, simulations show that the stress required to nucleate dislocations at these ultrahigh strain rates is about one order of magnitude smaller than typical values required for homogeneous nucleation of dislocation loops in bulk copper single crystals under quasi-static conditions.

36 MATERIALS SCIENCE↗

Mechanics of point defect diffusion near dislocations and grain boundaries: A chemomechanical framework

Diffusion of point defects during irradiation is simulated via a two-way coupling between mechanical stress and defect diffusion in iron. This diffusion is based on a modified chemical potential that includes not only the local concentration of radiation-induced defects, but also the influence of the residual stress field from both the microstructure (i.e. dislocations or grain boundaries) and the eigenstrain caused by the defects themselves. Defect flux and concentration rates are derived from this chemical potential using Fick’s first and second laws. Mean field rate theory is incorporated to model the annihilation of Frenkel pairs, and increased annihilation near grain boundaries is included based on the elastic energy of each grain boundary. Mechanical equilibrium is coupled with diffusion by computing eigenstrain from point defects and adding this to the total strain. Intrinsic stresses associated with the dislocations and grain boundaries are calculated using dislocation and disclination mechanics. Through this two-way-coupled model, regions of low concentration are seen near grain boundaries, and sink efficiency is calculated for different types of microstructure. Furthermore, the results show that the two-way mechanical coupling has a strong influence on sink efficiency for dislocation loops. The results also suggest that misorientation is a poor metric for determining sink efficiency, with sink density and elastic energy being much more informative.

36 MATERIALS SCIENCE↗

Orientation-selected micro-pillar compression of additively manufactured 316L stainless steels: Comparison of as-manufactured, annealed, and proton-irradiated variants

In this work, irradiation response and deformation mechanisms of additively manufactured (AM) 316L stainless steel were studied by atomic scale characterization and micro-pillar compression. The AM 316L stainless steels were fabricated by direct energy deposition, a laser-based additive manufacturing process. Irradiation with 2 MeV protons at 360°C was performed to create ~1.8 displacements-per-atom (dpa) damage in AM 316L. Deformation behaviors of the as-manufactured, annealed, and proton-irradiated variants were studied, focusing on the effects of manufacturing-induced pores, residual stress, and irradiation-introduced defects (dislocation loops and voids). Micro-pillars were prepared from grains of pre-selected orientation, avoiding contributions of grain boundaries and allowing determination of resolved shear stress on {111} glide planes. Transmission electron microscopy was used to characterize the pre- and post-deformation microstructure. It was found that in the as-manufactured alloy variant, moving dislocations were the major deformation carrier, with noticeable blocking by fabrication-induced pores, In the annealed variant, hardness was reduced, and deformation was also accomplished by dislocation gliding. In the proton-irradiated variant, significant twinning was observed. Comparing measured resolved shear stress and predicted critical stress for dislocation dissociation, we conclude that irradiation hardening became high enough to activate twinning. Therefore, the deformation mechanism changes from dislocation gliding to twinning. The study is important for both processing optimization and performance evaluation of AM alloys for reactor applications.

36 MATERIALS SCIENCE↗

Effect of Irradiation Mode on Irradiated Microstructure of HT9

Core components in Generation IV fast reactors are expected to be exposed to very high damage levels of 200 displacements per atom (dpa) and above. Numerous issues with in-reactor irradiations including residual radioactivity, expense, length of irradiation and availability have led to increased interest in ion irradiation as a surrogate. Self-ion irradiations can produce damage rates of around 10{sup -3} dpa/s with well-controlled temperature, doses and dose rates, allowing for accelerated irradiation testing. Along with these benefits, ion irradiations have been shown to reproduce many of the same irradiation-induced features as in reactor irradiations. Of particular interest at high doses is formation of voids, precipitates and evolution of the dislocation microstructure. However, the beam mode under ion irradiation must be addressed. Raster scanning has been shown to produce microstructural features similar to those observed in-reactor irradiations, however, since they are a pulsed type irradiation, they may induce artifacts as a result of annealing between pulses. Defocused beams have the benefit of full coverage 100% of the time, but may be challenging in terms of ensuring even irradiation over a large area as well as in reaching high enough currents to maintain acceptable damage rates to be useful as a surrogate. This paper reports upon the comparison of behavior of ferritic martensitic steels under a raster scanned or defocused beam mode. The objective is to determine the effect of beam condition the irradiated microstructural; specifically, on the formation of voids, precipitates and dislocation loops and analyze these results within the context of the FDRT model. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗

Using lifetime of point defects for dislocation bias in bcc Fe

The interaction between dislocations and point defects is key to deformation processes and microstructural evolution of structural materials. In this work, we compute the lifetime of point defects to describe their interaction with dislocations. This approach can accurately account for the effects of the dislocation core and anisotropic defect dynamics to accumulatively determine the capture efficiency, sink strength, and dislocation bias at different temperatures and dislocation densities. Particularly, the absorption of point defects by straight screw and edge dislocations in a model bcc iron system is studied. The maximum swelling rates based on the obtained bias factors are in close agreement with a variety of experimental measurements, including both neutron and ion-irradiation data, especially when considering the survival fraction for point defects from displacement cascades. Further, this approach applies to many other processes and sinks, such as dislocation loops and interfaces, providing a powerful means to develop fundamental insights critical for improving radiation resistance and mechanical properties of structural materials through controlling defect interaction and evolution.

36 MATERIALS SCIENCE↗

In-situ and ex-situ characterization of ion-irradiated AM materials

Additive manufacturing (AM) has attracted increasing attention in recent years as a new way of making high-quality components for nuclear reactors. While AM materials are compositionally similar to their conventionally produced counterparts, they do possess different microstructures, such as dislocation cells and chemical inhomogeneity, that can lead to different mechanical properties and performance behavior. In this study, the irradiation response of AM materials was investigated. In-situ and ex-situ ion irradiations were performed on AM316L and AM316H stainless steels (SS) at 300 and 600°C. The influence of the dislocation cell structure on the evolution of irradiation-induced dislocation loops was evident at 600ºC, but was much weaker at 300ºC. No voids were observed with the in-situ ion irradiation up to 10 dpa at both temperatures. Post-irradiation energy dispersive spectroscopy showed radiation-induced segregation (RIS) near grain boundaries and the formation of Cr-rich oxides throughout the matrix. The extent of segregation at dislocation cell walls varies with dose. Nanoindentation tests performed on the AM316L SS irradiated at 600ºC showed a complex dose dependence with softening at low doses and hardening at high doses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗