Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effect of operating conditions on gearbox noise

Low contact ratio spur gears were tested in the NASA gear noise rig to study the noise radiated from the top of the gearbox. The measured sound power from the gearbox top was obtained from a near field acoustic intensity scan taken at 63 nodes just above the surface. The sound power was measured at a matrix of 45 operating speeds and torque levels. Results are presented in the form of a spectral speed map and as a plot of sound power versus torque (at constant speed) and as sound power versus speed (at constant torque). Because of the presence of vibration modes, operating speed was found to have more impact on noise generation than torque level. A NASA gear dynamics code was used to compute the gear tooth dynamic overload at the same 45 operating conditions used for the experiment. Similar trends were found between the analytical results for dynamic tooth overload and experimental results for sound power. Dynamic analysis may be used to design high quality gears with profile relief optimized for minimum dynamic load and noise.

Oswald, Fred B.↗
DOE OSTI2016

Compression dynamics of quasi-spherical wire arrays with different linear mass profiles

Results of experimental studies of the implosion of quasi-spherical wire (or metalized fiber) arrays are presented. The goal of the experiments was to achieve synchronous three-dimensional compression of the plasma produced in different regions of a quasi-spherical array into its geometrical center. To search for optimal synchronization conditions, quasi-spherical arrays with different initial profiles of the linear mass were used. The following dependences of the linear mass on the poloidal angle were used: m{sub l}(θ) ∝ sin{sup –1}θ and m{sub l}(θ) ∝ sin{sup –2}θ. The compression dynamics of such arrays was compared with that of quasi-spherical arrays without linear mass profiling, m{sub l}(θ) = const. To verify the experimental data, the spatiotemporal dynamics of plasma compression in quasi-spherical arrays was studied using various diagnostics. The experiments on three-dimensional implosion of quasi-spherical arrays made it possible to study how the frozen-in magnetic field of the discharge current penetrates into the array. By measuring the magnetic field in the plasma of a quasi-spherical array, information is obtained on the processes of plasma production and formation of plasma flows from the wire/fiber regions with and without an additionally deposited mass. It is found that penetration of the magnetic flux depends on the initial linear mass profile m{sub l}(θ) of the quasi-spherical array. From space-resolved spectral measurements and frame imaging of plasma X-ray emission, information is obtained on the dimensions and shape of the X-ray source formed during the implosion of a quasi-spherical array. The intensity of this source is estimated and compared with that of the Z-pinch formed during the implosion of a cylindrical array.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2012

Antarctic Ice-Shelf Front Dynamics from ICESat

Time variable elevation profiles from ICESat Laser Altimetry over the period 2003-2009 provide a means to quantitatively detect and track topographic features on polar ice surfaces. The results of this study provide a measure of the horizontal motion of ice-shelf fronts. We examine the time histories of elevation profiles crossing the ice fronts of the Ross, Ronne, Filchner, Riiser-Larson and Fimbul shelves. This provides a basis for estimating dynamics in two dimensions, i.e. in elevation and horizontally in the along-track direction. Ice front velocities, corrected for ground-track intersection angle, range from nearly static to 1.1 km/yr. In many examples, a decrease in elevation up to 1 m/yr near the shelf frontis also detectable. Examples of tabular calving along shelf fronts are seen in some elevation profiles and are confirmed by corresponding MODIS imagery.

Robbins, John W.↗
DOE OSTI2020

Amphiphile Organization in Organic Solutions: An Alternative Explanation for Small-Angle X-ray Scattering Features in Malonamide/Alkane Mixtures

In this work, the role of different intermolecular interactions in the aggregation of amphiphiles in an organic solvent is studied for systems of relevance to liquid-liquid extraction (LLE), a chemical process used to selectively recover metals from complex mixtures. Of specific interest is the role, or lack thereof, of hydrogen bonding, which is often assumed to be a main driver of the organic phase structural organization that has been linked to separation efficacy. Toward that end, a series of malonamide extractants in n-dodecane have been studied in the absence of any extracted aqueous solutes, including water. The series of extractants includes N,N'-dimethyl-N,N'-dibutyltetradecylmalonamide (DMDBTDMA), two of its homologs, and N,N'-dimethyl-N,N'-dioctylhexylethoxymalonamide (DMDOHEMA). This simplified model LLE system enables systematic investigation of the role of dipole-dipole and alkyl tail steric interactions in amphiphile aggregation. Small-angle X-ray scattering (SAXS) profiles computed from molecular dynamics trajectories are in good agreement with experimental SAXS data. Molecular dynamics simulations show that malonamide aggregation results from dipole-driven self-association and lacks characteristic aggregate sizes. Mid-q correlation peaks in the SAXS profiles emerge at high concentration for each malonamide. In those densely packed solutions, the correlation peaks are observed to result from alkyl tail-induced spacing between electron-rich polar head groups, with peak positions determined by the different alkyl tail lengths present in the malonamide molecule. This explanation of the SAXS correlation peaks contrasts with the prevailing literature, which attributes mesoscale features observed in small-angle scattering to the formation of microemulsions. Instead, this work finds that these features are present in the absence of water or any reverse micellar organization of the malonamides. As such, molecular-scale malonamide self-association and packing, rather than microemulsion-based colloidal-scale descriptions, is a more appropriate framework for these LLE systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Density and temperature profiles after low-Z and high-Z shattered pellet injections on DIII-D

Abstract In this work we utilize the recently upgraded Thomson scattering diagnostic to resolve density and temperature plasma profiles after pure deuterium and mixed neon/deuterium shattered pellet injections (SPIs) on DIII-D. This allows us to study individual components of the staggered scheme proposed for disruption mitigation on ITER, consisting of a low-Z material SPI followed by a delayed high-Z SPI. Obtained spatio-temporal density profiles exhibit very different dynamics after dominantly neon and pure deuterium SPIs. The neon SPI causes a fast radiative plasma collapse in a few milliseconds and results in almost flat density profile once the impurity mixes with the plasma during and after the thermal quench (TQ). The deuterium SPI leads to a disruption delayed by ten and more milliseconds, but very limited core fueling can be observed before the disruption. Even during and after the TQ, the edge deuterium density significantly exceeds the core density. 1D transport modeling suggests that this poor core fueling can be explained by strong outward grad-B-induced drift of the injected deuterium. Preliminary simulations show that larger pellet shards and greater injected quantity can be used to improve the penetration of the low-Z material into the core. These results call for optimization and further evaluation of the staggered SPI on ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2017

Study of Plasma Flows Generated in Plasma Focus Discharge in Different Regimes of Working Gas Filling

Results are presented from experimental studies of the plasma flows generated in the KPF-4 Phoenix Mather-type plasma focus device (Sukhum Physical Technical Institute). In order to study how the formation and dynamics of the plasma flow depend on the initial distribution of the working gas, a system of pulsed gas puffing into the discharge volume was developed. The system allows one to create profiled gas distributions, including those with a reduced gas density in the region of plasma flow propagation. Results of measurements of the magnetic field, flow profile, and flow deceleration dynamics at different initial distributions of the gas pressure are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Phase transitions in high-purity zirconium under dynamic compression

In this work, we present results from ramp compression experiments on high-purity Zr that show the α → ω, ω → β, as well as reverse β → ω phase transitions. Simulations with a multi-phase equation of state and phenomenological kinetic model match the experimental wave profiles well. While the dynamic α ! ! transition occurs ~ 9 GPa above the equilibrium phase boundary, the ω → β transition occurs within 0.9 GPa of equilibrium. We estimate that the dynamic compression path intersects the equilibrium ω – β line at P = 29:2 GPa, and T = 490 K. The thermodynamic path in the interior of the sample lies ~ 100 K above the isentrope at the point of the ω → β transition. Approximately half of this dissipative temperature rise is due to plastic work, and half is due to the non-equilibrium α → ω transition. The inferred rate of the α → ω transition is several orders of magnitude higher than that measured in dynamic diamond anvil cell (DDAC) experiments in an overlapping pressure range. We discuss a model for the influence of shear stress on the nucleation rate. We find that the shear stress s ji has the same effect on the nucleation rate as a pressure increase δP = cϵ ij s ji /(ΔV/V); where c is a geometric constant ~ 1 and, ϵ ij are the transformation shear strains. The small fractional volume change ΔV/V ≈ 0:1 at the α → ω transition amplifies the effect of shear stress, and we estimate that for this case δP is in the range of several GPa. Correcting our transition rate to a hydrostatic rate brings it approximately into line with the DDAC results, suggesting that shear stress plays a significant role in the transformation rate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Quantifying Dissolution Dynamics in Porous Media Using a Spatial Flow Focusing Profile

Abstract The diverse range of patterns in porous media formed by dissolution processes depends on the relative magnitude of flow, transport, and chemical reactions at pore surfaces. However, distinguishing between regimes often relies solely on qualitative, visual comparisons of emergent structures. Here, we propose a quantitative measure capable of identifying different regimes using the concept of the spatial flow focusing profile, which segments the medium into cross sections along the flow direction to calculate the flow focusing index for each section. We employ this measure in numerical simulations of a dissolving porous medium using a pore network model. We obtain a morphological phase diagram of dissolution patterns, which we characterize using the flow focusing profile. In particular, we demonstrate that analyzing the temporal changes in the profile allows one to quantitatively distinguish between wormholing and channeling. The transition between them is shown to be affected by the heterogeneity of the system.

58 GEOSCIENCES↗
NASA NTRS1980

Physicochemical and dynamical processes in cometary ionospheres. I - The basic flow profile

The paper deals with the basic aspects of solar wind interaction with the ionosphere of a large comet and with detailed hydrodynamic models developed to describe the flow exterior to the tangential discontinuity surface that separates the outflowing purely cometary ions from the inflowing contaminated solar wind. The equation of the basic flow model and the results of a preliminary analysis of these equations are given, and the shape and structure of the shock layer are analyzed. The shock layer structure associated with fan-shaped comet emanating from the cometary nucleus in the general direction to the sun is identified.

Houpis, H. L. F.↗
NASA NTRS1978

GEOS-3 ocean current investigation using radar altimeter profiling

Both quasi-stationary and dynamic departures from the marine geoid were successfully detected using altitude measurements from the GEOS-3 radar altimeter. The quasi-stationary departures are observed either as elevation changes in single pass profiles across the Gulf Stream or at the crowding of contour lines at the western and northern areas of topographic maps generated using altimeter data spanning one month or longer. Dynamic features such as current meandering and spawned eddies can be monitored by comparing monthly mean maps. Comparison of altimeter inferred eddies with IR detected thermal rings indicates agreement of the two techniques. Estimates of current velocity are made using derived slope estimates in conjunction with the geostrophic equation.

Leitao, C. D.↗
DOE OSTI2024

Quantifying Variability and Controls of Riverine Dissolved Organic Carbon Exported to Arctic Coastal Margins of North America (Final Report)

This project involved implementation and application of a coupled permafrost hydrology and dissolved organic carbon process models to investigate how spatial and seasonal variations in terrestrial hydrology and soil freeze/thaw dynamics influence the mobilization, loading, and export of organic carbon to the stream network for selected arctic basins across northern Alaska and northwest Canada. The model simulations were constrained by detailed observations of in- stream chemistry, soil active layer profile moisture and temperature dynamics, streamflow, soil carbon inventories and satellite microwave remote sensing based assessments of surface soil freeze-thaw dynamics. We developed and applied the numerical modeling and data analysis, incorporating observed data for calibration and validation, in order to investigate the terrestrial hydrology, permafrost dynamics, and associated DOC production and loading to rivers across a region encompassing watersheds draining to the coast. The project produced six publications and three datasets archived in public repositories.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

One-dimensional temperature measurement of supersonic jet flow by resonantly ionized photoemission thermometry of molecular nitrogen

As the field of fluid dynamics progresses, the demand for sophisticated diagnostic methods to accurately assess flow conditions rises. In this work, resonantly ionized photoemission thermometry (RIPT) has been used to directly target and ionize diatomic nitrogen (N 2 ) to measure one-dimensional (1D) temperature profiles in a supersonic jet flow. This technique can be considered non-intrusive as the premise uses resonantly enhanced multiphoton ionization (REMPI) to target molecular nitrogen. This resonance excites N 2 into absorption bands of the P, Q, and R rotational branches of N 2 ( b 1 Π u ). The ideal (3 + 1) REMPI scheme excites from the ground state and ionizes N 2 ( b 1 Π u ← X 1 Σ g + ) where de-excitation results in photoemission from the first negative band of ionized N 2 + ( B 2 Σ u + → X 2 Σ g + ) as nitrogen returns to the ground state. The resulting emission can be observed using an intensified camera, thus permitting inference of the rotational temperature of ground-state molecular nitrogen. A linearly regressive Boltzmann distribution is applied based on previous calibration data for this technique to quantify the temperature along the ionized line. This work applies this technique to a pure N 2 supersonic jet in cross-flow and counter-flow orientations to demonstrate N 2 RIPT’s applications in a supersonic flow. Temperature variations are observed at different locations downstream of the exit in cross-flow, and axisymmetric in counter-flow, to generate profiles characterizing the flow dynamics. Due to the collisional effects resulting from the number density of N 2 at higher pressures, a (3 + 2) REMPI scheme is observed throughout this text.

Clark, Aleksander (ORCID:0009000855600042)↗
DOE OSTI2016

SU-F-T-527: A Novel Dynamic Multileaf Collimator Leaf-Sequencing Algorithm in Radiation Therapy

Purpose: A novel leaf-sequencing algorithm is developed for generating arbitrary beam intensity profiles in discrete levels using dynamic multileaf collimator (MLC). The efficiency of this dynamic MLC leaf-sequencing method was evaluated using external beam treatment plans delivered by intensity modulated radiation therapy technique. Methods: To qualify and validate this algorithm, integral test for the beam segment of MLC generated by the CORVUS treatment planning system was performed with clinical intensity map experiments. The treatment plans were optimized and the fluence maps for all photon beams were determined. This algorithm started with the algebraic expression for the area under the beam profile. The coefficients in the expression can be transformed into the specifications for the leaf-setting sequence. The leaf optimization procedure was then applied and analyzed for clinical relevant intensity profiles in cancer treatment. Results: The macrophysical effect of this method can be described by volumetric plan evaluation tools such as dose-volume histograms (DVHs). The DVH results are in good agreement compared to those from the CORVUS treatment planning system. Conclusion: We developed a dynamic MLC method to examine the stability of leaf speed including effects of acceleration and deceleration of leaf motion in order to make sure the stability of leaf speed did not affect the intensity profile generated. It was found that the mechanical requirements were better satisfied using this method. The Project is sponsored by the Scientific Research Foundation for the Returned Overseas Chinese Scholars, State Education Ministry.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Element Formation in Radiation-hydrodynamics Simulations of Kilonovae

Abstract Understanding the details of r -process nucleosynthesis in binary neutron star merger (BNSM) ejecta is key to interpreting kilonova observations and identifying the role of BNSMs in the origin of heavy elements. We present a self-consistent, two-dimensional, ray-by-ray radiation-hydrodynamic evolution of BNSM ejecta with an online nuclear network (NN) up to a timescale of days. For the first time, an initial numerical relativity ejecta profile composed of the dynamical component and spiral-wave and disk winds is evolved including detailed r -process reactions and nuclear heating effects. A simple model for the jet energy deposition is also included. Our simulation highlights that the common approach of relating in postprocessing the final nucleosynthesis yields to the initial thermodynamic profile of the ejecta can lead to inaccurate predictions. Moreover, we find that neglecting the details of the radiation-hydrodynamic evolution of the ejecta in nuclear calculations can introduce deviations of up to 1 order of magnitude in the final abundances of several elements, including very light and second r -process peak elements. The presence of a jet affects element production only in the innermost part of the polar ejecta, and it does not alter the global nucleosynthesis results. Overall, our analysis shows that employing an online NN improves the reliability of nucleosynthesis and kilonova light-curve predictions.

Magistrelli, Fabio (ORCID:0009000509767851)↗
DOE OSTI2018

Dynamic Adaptable Asynchronous Progress Model for MPI RMA Multiphase Applications

Casper is a process-based asynchronous progress model for MPI one-sided communication on multi-and many-core architectures. The one-sided communication is not truly one-sided in most MPI implementations: the target process still relies on software progress to complete incoming operations. Casper allows the user to specify an arbitrary number of cores dedicated to background ghost processes and transparently redirects the RMA operations to ghost processes by utilizing the PMPI redirection and MPI-3 shared-memory technologies. Although Casper benefits applications that suffer from lack of asynchronous progress, the operation redirection design might not support complex multiphase applications effectively, which often involve dynamically changing communication density and computing workloads. In this paper, we present an adaptive mechanism in Casper to address the limitation of static asynchronous progress in multiphase applications. For this we exploit two adaptive strategies, a user-guided strategy and a fully transparent and automatic strategy based on self-profiling and prediction, to dynamically reconfigure the asynchronous progress in Casper according to real-time performance characteristics during multiphase execution. We evaluate the adaptive approaches in both microbenchmarks and a real quantum chemistry application suite, NWChem, on the Cray XC30 supercomputer and an Intel Omni-Path cluster.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2013

THREE-DIMENSIONAL STELLAR KINEMATICS AT THE GALACTIC CENTER: MEASURING THE NUCLEAR STAR CLUSTER SPATIAL DENSITY PROFILE, BLACK HOLE MASS, AND DISTANCE

We present three-dimensional (3D) kinematic observations of stars within the central 0.5 pc of the Milky Way (MW) nuclear star cluster (NSC) using adaptive optics imaging and spectroscopy from the Keck telescopes. Recent observations have shown that the cluster has a shallower surface density profile than expected for a dynamically relaxed cusp, leading to important implications for its formation and evolution. However, the true 3D profile of the cluster is unknown due to the difficulty in de-projecting the stellar number counts. Here, we use spherical Jeans modeling of individual proper motions and radial velocities to constrain, for the first time, the de-projected spatial density profile, cluster velocity anisotropy, black hole mass (M {sub BH}), and distance to the Galactic center (R {sub 0}) simultaneously. We find that the inner stellar density profile of the late-type stars, ρ(r)∝r {sup –γ}, have a power law slope γ=0.05{sub −0.60}{sup +0.29}, much more shallow than the frequently assumed Bahcall-Wolf slope of γ = 7/4. The measured slope will significantly affect dynamical predictions involving the cluster, such as the dynamical friction time scale. The cluster core must be larger than 0.5 pc, which disfavors some scenarios for its origin. Our measurement of M{sub BH}=5.76{sub −1.26}{sup +1.76}×10{sup 6} M {sub ☉} and R{sub 0}=8.92{sub −0.55}{sup +0.58} kpc is consistent with that derived from stellar orbits within 1'' of Sgr A*. When combined with the orbit of S0-2, the uncertainty on R {sub 0} is reduced by 30% (8.46{sub −0.38}{sup +0.42} kpc). We suggest that the MW NSC can be used in the future in combination with stellar orbits to significantly improve constraints on R {sub 0}.

79 ASTRONOMY AND ASTROPHYSICS↗