Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode preparation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Copper iodide nanoparticles as a hole transport layer to CdTe photovoltaics: 5.5 % efficient back-illuminated bifacial CdTe solar cells

We report the role of copper iodide (CuI) nanoparticles (NPs) as a hole transport layer (HTL) in cadmium sulfide/cadmium telluride (CdS/CdTe) photovoltaics. These CuI NPs were prepared using solution processing at room temperature and used to fabricate monofacial and bifacial CdTe solar cells with different back contacts. Using CuI/Au as the back contact, the device efficiency reached to 14.8% with outstanding fill factor (FF) of 79.2%. Replacing the gold (Au) electrode with sputtered transparent indium tin oxide (ITO), a CuI/ITO back contact yielded photoconversion efficiencies (PCEs) of 11.6% and 5.5% under front and back illumination respectively. Bifacial devices (CdTe/ITO) without the CuI NP HTL have an efficiency of 7.0% and 1.0% for front and back illumination, respectively. For CuI/ITO, a current collection of 12.0 mAcm -2 was observed upon back illumination which significantly improved over an ITO-only back contact (5.0 mAcm -2 ). The PCE obtained from back illumination was enhanced when using CuI NPs as the HTL due to the reduced back barrier height, and improved back interface as determined by temperature dependent current vs. voltage characteristics and impedance spectroscopy analysis. The improvement in device performance of the bifacial configuration is a significant step forward toward realizing thin film photovoltaic modules which harvest energy incident on the rear of the module.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Uniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers

This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mg Ir cm −2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mg Ir cm −2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.

08 HYDROGEN↗
DOE OSTI2024

A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability

A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Additive manufacturing of LiCoO 2 electrodes via vat photopolymerization for lithium ion batteries

Additive manufacturing has the potential to revolutionize the fabrication of lithium-ion batteries for a diversity of applications including in portable, biomedical, aerospace, and the transportation fields. Standard commercial batteries consist of stacked layers of various components (current collectors, cathode, anode, separator and electrolyte) in a two-dimensional manner. By leveraging the latest advances in additive manufacturing and computer-aided design, an improved geometric and electrochemical configuration of these batteries can maximize energy efficiency while allowing design optimization to reduce dead space for a given application. In this work, a composite UV photosensitive resin was prepared and used as feedstock in a vat photopolymerization system. The resin was loaded with LiCoO 2 acting as electrochemically active material for the cathode of a lithium-ion battery, and was further improved with the addition of conductivity-enhancing carbonaceous additives. Challenges to additive manufacturing arise from the opacity and high viscosity of the composite nature of these electrochemically-active resins, which cause light refraction during selective UV curing. Subsequently, items were printed and subjected to a thermal post-processing step to obtain an adequate compromise between electrochemical performance and mechanical integrity. Both sintered and green state 3D printed cathodes were assembled into half-cell lithium-ion batteries using lithium metal as a reference and counter electrode. Electrochemical cycling of these batteries yielded satisfactory results approaching commercial LiCoO 2 cathodes’ performance, with the potential advantages of additive manufacturing – high surface area anode–cathode configurations for power performance as well as shape conformability.

25 ENERGY STORAGE↗
DOE OSTI2024

Oxidation Temperature-Dependent Electrochemical Doping of WO 3 Deposited via Atomic Layer Deposition

Silicon-based photoelectrochemical devices show promise for the performance of light-driven CO 2 reduction but suffer from instability under photoelectrochemical conditions relevant to CO 2 reduction. Coating silicon electrodes with thin layers of metal oxides has shown promise to passivate unstable silicon surfaces, and many different metal oxides can be deposited on silicon using various techniques. In this study, we investigate the fundamental photoelectrochemical performance of WO 3 -coated silicon photoelectrodes, which were generated by oxidation of W-metal films deposited via atomic layer deposition on both degenerately doped (nSi + ) and low-doped (pSi) silicon. Two different oxidation temperatures were investigated (400 and 600 °C), and it was found that the monoclinic phase of WO 3 predominates at both temperatures but that more grain boundaries are present in the 600 °C film. From X-ray photoelectron spectroscopy, the stoichiometry of both films was found to be 1:3 W:O, and low electron energy loss experiments indicate band gaps of 3.0 and 3.1 eV for 400 and 600 °C films, respectively. Cyclic voltammetry experiments showed that the electron transfer kinetics increased after continued redox cycling, particularly for the material produced at 400 °C. X-ray photoelectron spectra suggest that the observed increase in electrode conductivity is due to the formation of oxygen vacancies in the film. Electrochemical impedance spectroscopy indicated that charge transport through the films was impacted by the grain boundaries that formed during oxidation of the film. Photoelectrochemical studies on pSi/WO 3 electrodes were highly variable, only producing a photocurrent and photovoltage with some samples. Our best sample, formed at 400 °C, produced a photovoltage of 180 mV, which is lower than what has previously been reported for WO 3 -coated silicon (500 mV). We hypothesize that the variability in photoelectrochemical experiments arose from a roughened WSiO x interface that is generated during film preparation. WO 3 shows promise as a metal oxide coating for silicon, but our results suggest that formation of a high-quality interface between Si and WO 3 is vital for best performance.

Charge transfer↗
DOE OSTI2022

Atomic Molybdenum for Synthesis of Ammonia with 50% Faradic Efficiency

The electrochemical dinitrogen (N 2 ) reduction reaction (NRR) under ambient conditions has gained significant interest as an environmentally friendly alternative to the traditional Haber–Bosch process for the synthesis of ammonia (NH 3 ). However, up to now, most of the reported NRR electrocatalysts with satisfactory catalytic activities have been hindered by the large overpotential in N 2 activation. The preparation of highly efficient Mo-based NRR electrocatalyst in acidic electrolytes under ambient conditions is demonstrated here, consisting of stabilized single Mo atoms anchored on holey nitrogen-doped graphene synthesized through a convenient potassium-salt-assisted activation method. At -0.05 V versus a reversible hydrogen electrode (RHE), an electrode consisting of the resultant electrocatalyst immobilized on carbon fiber paper can attain an exceptional Faradaic efficiency of 50.2% and a NH3 yield rate of 3.6 µg h -1 mg cat -1 with low overpotentials. Density functional theory calculations further unveil that compared to the original graphene without holes, the edge coordinated Mo atoms and the existence of vacancies on holey graphene lower the overpotential of N 2 reduction, thereby promoting the NRR catalytic activity. Finally, this work could provide new guidelines for future designs in single-atom catalysis that would be beneficial to ambient N 2 fixation, and replacement of classical synthesis processes that are very energy-intensive.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Capturing carbon dioxide from air with charged-sorbents

Emissions reduction and greenhouse gas removal from the atmosphere are both necessary to achieve net-zero emissions and limit climate change. There is thus a need for improved sorbents for the capture of carbon dioxide from the atmosphere, a process known as direct air capture. In particular, low-cost materials that can be regenerated at low temperatures would overcome the limitations of current technologies. In this work, we introduce a new class of designer sorbent materials known as ‘charged-sorbents’. These materials are prepared through a battery-like charging process that accumulates ions in the pores of low-cost activated carbons, with the inserted ions then serving as sites for carbon dioxide adsorption. We use our charging process to accumulate reactive hydroxide ions in the pores of a carbon electrode, and find that the resulting sorbent material can rapidly capture carbon dioxide from ambient air by means of (bi)carbonate formation. Unlike traditional bulk carbonates, charged-sorbent regeneration can be achieved at low temperatures (90–100 °C) and the sorbent’s conductive nature permits direct Joule heating regeneration using renewable electricity. Given their highly tailorable pore environments and low cost, we anticipate that charged-sorbents will find numerous potential applications in chemical separations, catalysis and beyond.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Directly Embedded Ni3S2/Co9S8@S-Doped Carbon Nanofiber Networks as a Free-Standing Anode for Lithium-Ion Batteries

Transition metal sulfides as electrode materials for lithium-ion batteries have attracted significant research attention due to their high theoretical capacity, excellent redox reversibility, and earth abundance. However, this material family still suffers from poor conductivity and experiences huge volume changes. Here, we demonstrate a facile and scalable electrospinning method to prepare Ni3S2 and Co9S8 nanoparticles embedded in sulfur doped carbon nanofiber networks as a free-standing anode material for lithium ion batteries. Similar to literature findings, the coupling of two different metal sulfides indeed synergistically promoted the electrochemical performance. Embedding them within individual carbon nanofibers not only enhances the intrinsic conductivity, but also provides a highly stable structure, which results in excellent battery performance. Furthermore, the individual carbon nanofibers intertwine with each other to form a free-standing 3D nanofiber network which acts as a freeway network for fast electron transfer and the pores between fibers allow easy penetration of the electrolyte, namely easy lithium ion access to active nanoparticles. When directly applied as the anode in lithium ion batteries, the free-standing nanofiber mat bypassed all slurry making steps and showed excellent cycling stability with a high specific capacity of 528 mA h g-1 after 200 cycles at a current density of 300 mA g-1. Good rate capability was also obtained. Additionally, the charge storage process analysis indicated that the pseudocapacitive behavior of the material is attributed to its good performance. This work introduces a facile strategy to simultaneously and in situ generate Co9S8 and Ni3S2 nanoparticles within a S-doped carbon fiber matrix via facile electrospinning followed by a one-step heating procedure. It is demonstrated that the free-standing transition bimetallic sulfide nanofibers prepared are very promising for light and small battery applications.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗
DOE OSTI2024

(CrMnCoNiZn) 3 O 4 @PPy core-shell nanocomposite with excellent electrochemical performance as lithium-ion battery anode

High entropy oxides (HEOs) have an excellent potential for use as electrode materials in lithium-ion batteries (LIBs) due to their high theoretical specific capacity. In this work, spinel-structured (CrMnCoNiZn) 3 O 4 HEO nanoparticles with five elements in equal molar ratio is first generated by solution combustion method. (CrMnCoNiZn) 3 O 4 @polypyrrole (PPy) nanocomposites are prepared by in-situ polymerization method. As an anode for lithium-ion batteries, the electrochemical performance of the (CrMnCoNiZn) 3 O 4 @PPy composite outperforms that of (CrMnCoNiZn) 3 O 4 nanoparticles. The capacity is 802 mAh/g after 100 cycles at a current density of 100 mA/g, 416 mAh/g after 1000 cycles at a high current density of 1 A/g, and 360 mAh/g rate capacity at 2 A/g. The excellent electrochemical performance of the composites is mainly due to the fact that the conductive and flexible PPy is encapsulated on the high-entropy oxides, which can alleviate the volume change triggered by extraction-insertion of lithium ions process, as well as enhance the electrical conductivity and reduce the occurrence of some side reactions. Finally, this method of compositing materials can also be used in other HEOs and conductive polymers, providing a new idea to enhance the electrochemical properties of HEOs.

25 ENERGY STORAGE↗
DOE OSTI2021

Simultaneous Electrospinning and Electrospraying for the Preparation of a Precursor Membrane Containing Hydrothermally Generated Biochar Particles to Produce the Value-Added Product of Carbon Nanofibrous Felt

Biochar is a byproduct generated from the hydrothermal liquefaction of biomass, such as corn stover, in an anaerobic environment. This work aims to convert biochar into a value-added product of carbon nanofibrous felt. First, the biochar-containing precursor membrane was prepared from simultaneous electrospinning and electrospraying. After thermal stabilization in air and carbonization in argon, the obtained precursor membrane was converted into a mechanically flexible and robust carbon nanofibrous felt. Electrochemical results revealed that the biochar-derived carbon nanofibrous felt might be a good candidate as a supercapacitor electrode with a good rate capability and high kinetic performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Effect of the Nature of Both Cation and Anion Substitution on the Structural Symmetry of Li‐Rich 3 d ‐Metal Chalcogenide Electrodes

Abstract Li‐rich layered chalcogenides have recently led to better understanding of the anionic redox process and its associated high capacity while providing ways to overcome its practical limitations of voltage fade and irreversibility. This study reports on the feasibility of triggering anionic activity in Li 2 TiS 3 , through anionic substitution (Se for S) or cationic substitution (Fe for Ti). Herein, the chalcogenide chemical space is further explored to prepare mono‐substituted Li 1.7 Ti 0.85 Mn 0.45 Ch 3 (Ch = S/Se) and doubly substituted cationic and anionic phases (Li 1.7 Ti 0.85 Fe 0.45 S 3‐z Se z ) which crystallize either in the O3‐ or O1‐type structures depending upon substituents. All series show a bell‐shape capacity variation as function of the transition metal (TM) substitution degree with values up to 240 mAh g −1 . For specific compositions, a structural O3 to O1 phase transition is observed upon Li removal, which is not reversible upon Li re‐insertion due to kinetic limitations and negatively affects long‐term cycling performance. Density functional theory (DFT) calculations confirm the O3/O1 relative stability along the different series and point subtle electronic differences in the TM‐doping, rationalizing the structural and electrochemical behaviors of these phases upon cycling. These findings provide further insights into the link between structural and electronic stability, which is of key importance for designing chalcogenide‐based anionic redox compounds.

Chemistry↗
DOE OSTI2025

Investigating the impact of preparation routes on the properties of copper-decorated silicon particles as anode materials for lithium-ion batteries

In recent years, the calendar life of Si has been recognized as a significant issue that must be addressed prior to technology deployment: The carbon conductive additive is a potential source of parasitic side reactions. However, carbon remains essential due to the low electronic conductivity of Si. In this study, we investigate the use of Cu as a conductive additive and potential alternative to carbon. Some Cu-decorated silicon particles (Si Cu ) were prepared using physical vapor deposition (PVD) via sputtering and high-energy milling. Other Si Cu particles were prepared by using a solution method and examined briefly. The milling method caused Cu to appear as island-like features on the Si surface, whereas the PVD method initially produced similar island-like features that gradually developed into a continuous coating around the Si as sputtering time increased. Electrodes fabricated from Si Cu exhibited lower overall resistivity, demonstrating the beneficial effect of Cu in improving electronic percolation through the electrode. Electrochemical tests showed that the milled SiCu exhibited higher capacity retention, improved rate capability, and lower overpotential. Furthermore, Si Cu coupled with an NMC811 cathode exhibited lower leakage currents compared with the baseline silicon, indicating that incorporating Cu provided an additional advantage of minimizing parasitic currents in the cells.

25 ENERGY STORAGE↗
DOE OSTI2020

Cobalt Metal–Cobalt Carbide Composite Microspheres for Water Reduction Electrocatalysis

Microspheres of cobalt metal–cobalt carbide (Co–Co x C, Co x C: Co 2 C and Co 3 C) composite with carbon shells were prepared via an OH – - and Cl – -assisted polyol method and explored for electrocatalytic activity and stability for the hydrogen evolution reaction (HER) in acidic media. From our transmission electron microscopy observations, the outermost surfaces of the as-prepared Co–Co x C composites were primarily covered with Co 2 C crystallites. Our best performing electrocatalyst exhibited superior HER activity with an overpotential of 78 mV to reach a current density of -10 mA·cm –2 , a Tafel slope of 87.8 mV·dec –1 , and 1 h of electrode durability. We show that this excellent HER performance is primarily due to the superior intrinsic activity of Co 2 C, as well as the high electrical conductivity resulting from the inclusion of cobalt metal and the presence of graphitic carbon shells in and on the composite, respectively. Using both computational and experimental approaches, we determine here that the carbon-rich cobalt carbide (Co 2 C) phase is more favorable for the HER than the carbon-poor phase (Co 3 C).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Electrostatic‐Attraction‐Driven Self‐Assembled Graphene‐Disordered Rocksalt Composite Cathode for Lithium‐Ion Batteries

Disordered rocksalt cathodes hold promise for achieving high-capacity lithium-ion batteries while using low-cost, earth-abundant elements. However, their electrochemical performance remains critically limited by their poor electronic conductivity. Conventional strategies such as high-energy ball milling with excess carbon additives can improve conductivity but remain challenging to scale and often produce defects and increase surface area, thereby accelerating capacity degradation. Herein, we report an alternative approach of electrostatic-attraction-driven self-assembly to fabricate Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 (LMTOF) particles uniformly wrapped with electronically conductive graphene sheets without associated materials degradation. The graphene-wrapped LMTOF demonstrates significantly improved cycling stability (89% capacity retention after 100 cycles) and superior rate capability compared with an LMTOF-carbon composite electrode fabricated using the conventional high-energy ball-milling process. Post-cycling analysis reveals reduced oxygen evolution, suppressed unwanted side reactions, and improved structural integrity for the graphene-LMTOF composite. This work highlights the advantages of solution-based carbon wrapping and offers a scalable strategy to prepare high-performance DRX cathodes for lithium-ion batteries.

carbon composite↗
DOE OSTI2020

Phase-Selective Epitaxial Growth of Heterophase Nanostructures on Unconventional 2H-Pd Nanoparticles

Heterostructured, including heterophase, noble-metal nanomaterials have attracted much interest due to their promising applications in diverse fields. However, great challenges still remain in the rational synthesis of well-defined noble-metal heterophase nanostructures. Furthermore, we report the preparation of Pd nanoparticles with an unconventional hexagonal close-packed (2H type) phase, referred to as 2H-Pd nanoparticles, via a controlled phase transformation of amorphous Pd nanoparticles. Impressively, by using the 2H-Pd nanoparticles as seeds, Au nanomaterials with different crystal phases epitaxially grow on the specific exposed facets of the 2H-Pd, i.e., face-centered cubic (fcc) Au (fcc-Au) on the (002)h facets of 2H-Pd while 2H-Au on the other exposed facets, to achieve well-defined fcc-2H-fcc heterophase Pd@Au core–shell nanorods. Moreover, through such unique facet-directed crystal-phase-selective epitaxial growth, a series of unconventional fcc-2H-fcc heterophase core–shell nanostructures, including Pd@Ag, Pd@Pt, Pd@PtNi, and Pd@PtCo, have also been prepared. Impressively, the fcc-2H-fcc heterophase Pd@Au nanorods show excellent performance toward the electrochemical carbon dioxide reduction reaction (CO 2 RR) for production of carbon monoxide with Faradaic efficiencies of over 90% in an exceptionally wide applied potential window from –0.9 to –0.4 V (versus the reversible hydrogen electrode), which is among the best reported CO 2 RR catalysts in H-type electrochemical cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Cu and Ni Co-sputtered heteroatomic thin film for enhanced nonenzymatic glucose detection

Abstract In this work, we report a wafer-scale and chemical-free fabrication of nickel (Ni) and copper (Cu) heteroatomic Cu–Ni thin films using RF magnetron sputtering technique for non-enzymatic glucose sensing application. The as-prepared wafer-scale Cu–Ni thin films exhibits excellent electrocatalytic activity toward glucose oxidation with a 1.86 μM detection limit in the range of 0.01 mM to 20 mM range. The Cu–Ni film shows 1.3- and 5.4-times higher glucose oxidation activity in comparison to the Cu and Ni electrodes, respectively. The improved electrocatalytic activity is attributed to the synergistic effect of the bimetallic catalyst and high density of grain boundaries. The Cu–Ni electrodes also possessed excellent anti-interference characteristics. These results indicate that Cu–Ni heteroatomic thin film can be a potential candidate for the development of non-enzymatic glucose biosensor because of its chemical free synthesis, excellent reproducibility, reusability, and long-term stability.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Mesoporous PdAg Nanospheres for Stable Electrochemical CO 2 Reduction to Formate

Palladium is a promising material for electrochemical CO 2 reduction to formate with high Faradaic efficiency near the equilibrium potential. It unfortunately suffers from problematic operation stability due to CO poisoning on surface. In this work, it is demonstrated that alloying is an effective strategy to alleviate this problem. Mesoporous PdAg nanospheres with uniform size and composition are prepared from the co-reduction of palladium and silver precursors in aqueous solution using dioctadecyldimethylammonium chloride as the structure-directing agent. The best candidate can initiate CO 2 reduction at zero overpotential and achieve high formate selectivity close to 100% and great stability even at <-0.2 V versus reversible hydrogen electrode. The high selectivity and stability are believed to result from the electronic coupling between Pd and Ag, which lowers the d-band center of Pd and thereby significantly enhances its CO tolerance, as evidenced by both electrochemical analysis and theoretical simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Light-Controlled Nanoparticle Collision Experiments

Electrochemical monitoring of catalytically amplified collisions of individual metal nanoparticles (NP) with ultramicroelectrodes (UME) has been extensively used to study electrocatalysis, mass-transport, and charge-transfer processes at the single NP level. More recently, photoelectrochemical collision experiments were carried out with semiconductive NPs. Here we introduce two new types of light-controlled nano-impact experiments. The first experiment involves localized photodeposition of catalyst (Pt) on TiO 2 NPs with a glass-sheathed carbon fiber simultaneously serving as the light guide and collector UME. The collisions of in situ prepared Pt@TiO 2 NPs with the carbon surface produced blips of water oxidation current, while the activity of pristine TiO 2 NPs was too low to yield measurable signal. In another experiment, collisions of catalytic (Ir oxide) NPs with the semiconductor (Nb doped n-type TiO 2 rutile single crystal) electrode are monitored by measuring the photocurrent of water oxidation.

14 SOLAR ENERGY↗