Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Size Effects on Deformation and Fracture of Scandium Deuteride Films.

Metal hydride films have been observed to crack during production and use, prompting mechanical property studies of scandium deuteride films. The following focuses on elastic modulus, fracture, and size effects observed in the system for future film mechanical behavior modeling efforts. Scandium deuteride films were produced through the deuterium charging of electron beam evaporated scandium films using X-ray diffraction, scanning Auger microscopy, and electron backscatter diffraction to monitor changes in the films before and after charging. Scanning electron microscopy, nanoindentation, and focused ion beam machined micropillar compression tests were used for mechanical characterization of the scandium deuteride films. The micropillars showed a size effect for flow stress, indicating that film thickness is a relevant tuning parameter for film performance, and that fracture was controlled by the presence of grain boundaries. Elastic modulus was determined by both micropillar compression and nanoindentation to be approximately 150 GPa, Fracture studies of bulk film channel cracking as well as compression induced cracks in some of the pillars yielded a fracture toughness around 1.0 MPa-m1/2. Preliminary Weibull distributions of fracture in the micropillars are provided. Despite this relatively low value of fracture toughness, scandium deuteride micropillars can undergo a large degree of plasticity in small volumes and can harden to some degree, demonstrating the ductile and brittle nature of this material

Teresi, C. S.↗

Effect of initial orientation on dynamic recrystallization of a zirconium alloy during hot deformation

Highlights: • The dynamic recrystallization process is enhanced by the operation of slip. • Continuous dynamic recrystallization is promoted by the rotation of grains. • Texture induced hardening hides the softening induced by dynamic recrystallization. - Abstract: The present study investigated the influence of the initial orientation on the dynamic recrystallization (DRX) behavior of a Zr-1Sn-0.3Nb alloy. A hot-rolled and annealed Zr sheet was compressed along two directions: along the normal direction so that the grains' -axis was nearly parallel to the loading direction (0° sample) and along the transverse direction so that the grains' -axis was nearly perpendicular to the loading direction (90° sample). The samples were compressed at 700 °C at a strain rate of 1 s{sup −1}. The microstructures at different strains were characterized by the electron backscatter diffraction (EBSD) technique, and conventional dislocation analysis using transmission electron microscope (TEM) was performed. A threshold value of grain orientation spread (GOS) equaled to 5° was used to distinguish the dynamically recrystallized grains from the deformed matrix. The results revealed that the DRX behavior strongly depended on the initial orientation. The Schmid factor analysis and TEM observation confirmed that pyramidal slip operated from the first stage of deformation in the 0° sample but not in the 90° sample. For the 0° sample, in the early and medium stages of deformation, due to the high stored energy caused by the operation of pyramidal slip, DDRX was mainly contributed to the formation of new fine grains. However, in the later stage of deformation, the DRX mechanism changed from DDRX to CDRX. In the 90° sample, although DDRX featured by grain boundary bulging occurred, the main DRX mechanism was CDRX in the whole deformation processing. Moreover, texture induced hardening in the early stage of deformation hides the softening induced by DDRX.

36 MATERIALS SCIENCE↗

Degradation of a Cr-Mo steel by carbide precipitation over long-term service

Microstructure of the 40-year service-exposed 1Cr-0.5Mo steel extracted from pressure vessels through the boat sampling technique was characterized using x-ray diffraction, field-emission scanning electron microscopy, energy dispersive spectrometry, electron backscatter diffraction, focused ion beam, and transmission electron microscopy. The microstructure degradation during long-term service was identified. Statistical crystal plastic ity models were developed to correlate the microstructure and mechanical properties quantitatively. The steel is found significantly strengthened but slightly embrittled. Nanoscale Mo 2 C carbides have nucleated within the ferrite matrix over the long-term service, resulting in significant strengthening of the matrix. The coarser grain boundary Cr 23 C 6 carbides, on the other hand, act as the damage accumulation sites and lead to the degradation.

36 MATERIALS SCIENCE↗

In situ measurement and modelling of the growth and length scale of twins in α -uranium

Twinning is an important deformation mechanism in crystalline materials. Twins nucleate, then grow, forming a discrete pattern of deformation bands with a certain thickness. The mechanism for twin growth is not completely understood. We present a simple phase field model which captures the physics of twin growth and reproduces the details observed during in situ electron backscatter diffraction experiments on α-uranium. The interaction between residual dislocations at twin interfaces and mobile dislocations in untwinned regions increases the stress needed for twin growth. This is described by a nonlocal term in the proposed constitutive equations: the nucleation stress of a twin increases proportionally to the twin phase field in a neighborhood. Competition between slip and twinning favors the nucleation of a new twin rather than the growth of a preexisting twin. The phase field model is coupled with a crystal plasticity finite element solver that includes the plastic deformation due to twinning. Simulations are able to reproduce the number of twins and their thicknesses as a function of the strain observed during in situ electron backscatter diffraction experiments. The stress-strain curve is also reproduced. This comparison allows the values of the nucleation stress and the interaction strength between residual and mobile dislocations to be found. It also gives an estimation of the density of residual dislocations that is consistent with the observed twin thickness. Finally, this model can be applied to understand microstructural effects in materials using twinning as a strengthening mechanism.

36 MATERIALS SCIENCE↗

Characterization of mechanical deformation in aluminum by optical second harmonic generation

Second harmonic generation (SHG), a laser-based surface technique, was used to characterize near-surface defect evolution associated with mechanical deformation in 2024-T3 aluminum due to tensile loads. Electron backscatter diffraction (EBSD) measurements were also performed to determine the geometrically necessary dislocation density before and after tensile deformation. Comparison of the EBSD and SHG results found that dislocation density and SHG signal are inversely proportional; tensile deformation in the plastic regime led to an increase in dislocation density and a decrease in SHG response. A similar trend was seen in the SHG results on as-received (unpolished) Al samples; SHG response decreases with extent of plastic deformation. Furthermore, this study suggests that SHG has potential as a nondestructive evaluation technique.

36 MATERIALS SCIENCE↗

Processing effects on microstructure in Er and ErD 2 thin-films

Erbium metal thin-films have been deposited on molybdenum-on-silicon substrates and then converted to erbium dideuteride (ErD 2 ). Here in this work, we study the effects of deposition temperature (≈300 or 723 K) and deposition rate (1 or 20 nm/s) upon the initial Er metal microstructure and subsequent ErD 2 microstructure. We find that low deposition temperature and low deposition rate lead to small Er metal grain sizes, and high deposition temperature and deposition rate led to larger Er metal grain sizes, consistent with published models of metal thin-film growth. ErD 2 grain sizes are strongly influenced by the prior-metal grain size, with small metal grains leading to large ErD 2 grains. A novel sample preparation technique for electron backscatter diffraction of air-sensitive ErD 2 was developed, and allowed the quantitative measurement of ErD 2 grain size and crystallographic texture. Finer-grained ErD 2 showed a strong (1 1 1) fiber texture, whereas larger grained ErD 2 had only weak texture. Finally, we hypothesize that this inverse correlation may arise from improved hydrogen diffusion kinetics in the more defective fine-grained metal structure or due to improved nucleation in the textured large-grain Er.

36 MATERIALS SCIENCE↗

Relating Texture and Thermomechanical Processing Variables in Mg–Zn–Ca Alloys

It is well known that the strong basal texture commonly produced in magnesium alloy sheets leads to poor formability at room temperature. A sizable body of work has explored how changing the alloy composition and rolling conditions can yield more desirable textures; however important thermomechanical variables, such as the feed rate during rolling, are often not included in the literature, making it difficult to correlate how changes in processing affect the final crystallographic texture. This work explores the texture evolution and grain refinement in Mg-Zn-Ca alloys during plane strain compression (PSC) using a Gleeble thermomechanical simulator. This instrument allows for precise control and capture of the thermomechanical history of the sample. The texture and grain morphology of the compressed samples were characterized using Electron Backscatter Diffraction (EBSD). The texture results will be used to identify which alloys and processing conditions should be scaled up for future rolling studies.

36 MATERIALS SCIENCE↗

The material dependence of temperature measurement resolution in thermal scanning electron microscopy

Thermal scanning electron microscopy is a recently developed temperature mapping technique based on thermal diffuse scattering in electron backscatter diffraction in a scanning electron microscope. It provides nano-scale and non-contact temperature mapping capabilities. Due to the specific temperature sensitive mechanism inherent to this technique, the temperature resolution is highly material dependent. A thorough investigation of what material properties affect the temperature resolution is important for realizing the inherent temperature resolution limit for each material. In this paper, three material dependent parameters-the Debye-Waller B-factor temperature sensitivity, backscatter yield, and lattice constant-are shown to control the temperature resolution.

36 MATERIALS SCIENCE↗

Structure fragmentation of a surface layer of commercial purity titanium during ultrasonic impact treatment

The mechanisms of surface layer fragmentation of titanium specimens subjected to ultrasonic impact treatment is investigated by atomic force microscopy, transmission electron microscopy and electron backscatter diffraction. It is shown that the twin boundaries Σ7b and Σ11b are unable to be strong obstacles for propagation of dislocations and other twins.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multiscale surface roughening of commercial purity titanium during uniaxial tension

The mechanisms of the surface roughening of the titanium specimens during uniaxial tension were demonstrated. By means of optical profilometry and electron backscattered diffraction it was shown that the formation of surface roughening is a multilevel process. The correlation between the density of slip in some grains, and grain rotation, and their displacement towards the free surface was investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Microstructure and mechanical properties development of micro channel tubes in extrusion, rolling and brazing

Highlights: • Rolling and brazing greatly affect the properties of micro-channel tubes (MCTs). • The properties of MCTs are investigated by the evolution of the microstructure. • Strength is decreased by 47% at 5%-rolling reduction ratio and 3-minute brazing. • Ductile fracture mode is observed by OM at failure of MCTs under inner pressure. - Abstract: In addition to extrusion, the post-processing of rolling and brazing has significant effect on the mechanical properties of multi-port tubes. The aluminum micro channel tubes, especially the seam welding zone in the internal webs, are investigated in terms of mechanical tests, microstructure characterization, and finite element analysis. The effect of the post-process of rolling are quantified by varying amount of rolling reduction ratios. Tensile strength and pressure bearing capacity are determined by tensile tests and burst pressure tests, respectively. The evolution of the microstructure within the seam wielding zone is characterized by Electron backscattered diffraction (EBSD) and optical microscopy (OM). The fracture profile observed by OM indicates ductile fracture mode. The pressure bearing capacity is reduced by ~47% at 5% reduction ratio of rolling followed by 3-minute brazing, where largest grains are obtained due to abnormal grain growth.

36 MATERIALS SCIENCE↗

Microstructure-Property Relationships in Epitaxial Cu(In, Ga)Se2 Solar-Cell Absorbers

Epitaxially grown Cu(In,Ga)Se 2 (CIGS) absorber layers were analyzed by various techniques in scanning electron microscopy in order to reveal microstructure-property relationships in these thin films. Owing to their epitaxial nature, these CIGS absorber layers do not contain any grain boundaries, but only anti-phase domains (APDs) and dislocations. By combining electron channeling-contrast imaging, electron backscatter diffraction, and cathodoluminescence (CL), in some cases on identical specimen positions of polished cross-sections of CIGS/Mo/glass stacks, it was possible to correlate the presence and orientations of APDs and dislocations with the lateral distributions of the CL intensity and emission-peak energy. We studied CIGS layers with three different [Ga]/([Ga]+[In]) ratios as well as with and without NaF/KF treatments. Considerable differences between the CIGS layer properties in the microstructure-property relationships were found, depending on the growth parameters. Dislocations in the epitaxial CIGS layers do not tend to exhibit strong CL intensity decreases, which contrasts with the situation in numerous other semiconductor materials.

anti-phase domains↗

Deformation and strain hardening of different steels in impact dominated systems

Strain hardening is a common technique to exploit the full potential of materials in diverse applications. Single impact studies were performed to evaluate work hardening effects of different steels, correlated to their deformation at different energy and momentum levels. Three different steels were examined regarding their forming behavior and their tendency to strain harden in impact loading conditions, revealing different intensities of hardness increase, deformation and coinciding microstructural changes. Detailed studies in the deformed zone such as micro hardness mappings were performed to reveal the materials hardness increase in the deformed zones. Additionally high resolution scanning electron microscopy (HRSEM) supported by electron backscatter diffraction (EBSD) was used to determine microstructural changes. Results indicate, that the influence of different velocities/strain rates at constant energy levels cannot be neglected for the strain hardening behavior of steels and provide data for a better control of the hardness increase in impact dominated materials fabrication operations. - Highlights: • Deformation and strain hardening behaviour of three different steels. • Influence of impact energies and momenta on the strain hardening. • Hardness increase and depth controllable by momentum and energy.

36 MATERIALS SCIENCE↗

Grain and subgrain boundaries in ultrafine-grained materials

The attractive metallographic electron backscatter diffraction (EBSD) method is used to describe the effect of the number N of passes on the subgrain and grain structures of pure aluminium and copper processed by equal channel angular pressing (ECAP). The remarkable feature of the aluminium structure is the lack of high angle boundaries after a low number (N = 2, 4) of passes and this remains preserved even after a relatively long annealing time. On the other hand, the boundary structure of copper is relatively stable and high angle boundaries always prevail.

36 MATERIALS SCIENCE↗

Identification of sub-grains and low angle boundaries beyond the angular resolution of EBSD maps

A new method called ALGrId (Anti-Leak GRain IDentification) is proposed for the detection of sub-grains beyond the relative angular resolution of Electron Backscatter Diffraction maps. It does not use any additional information such as Kikuchi Pattern Quality map nor need data filtering. It uses a modified Dijkstra algorithm which seeks the continuous set of boundaries having the highest average disorientation angle. - Highlights: • ALGrId is a new method to identify sub-grains and low angle boundaries in EBSD maps. • Unlike classical methods, ALGrId works even beyond the relative angular resolution. • If the orientation noise peaks at 0.7°, ALGrid detects 0.4°-boundaries correctly. • In the same example, the classical algorithm identifies 1.1°-boundaries only.

36 MATERIALS SCIENCE↗

Multi-probe microstructure tracking during heat treatment without an in-situ setup: Case studies on martensitic steel, dual phase steel and β-Ti alloy

In-situ scanning electron microscopy observations of the microstructure evolution during heat treatments are increasingly demanded due to the growing number of alloys with complex microstructures. Post-mortem characterization of the as-processed microstructures rarely provides sufficient insight on the exact route of the microstructure formation. On the other hand, in-situ SEM approaches are often limited due to the arising challenges upon using an in-situ heating setup, e.g. in (i) employing different detectors, (ii) preventing specimen surface degradation, or (iii) controlling and measuring the temperature precisely. Here, we explore and expand the capabilities of the “mid-way” solution by step-wise microstructure tracking, ex-situ, at selected steps of heat treatment. This approach circumvents the limitations above, as it involves an atmosphere and temperature well-controlled dilatometer, and high resolution microstructure characterization (using electron channeling contrast imaging, electron backscatter diffraction, atom probe tomography, etc.). We demonstrate the capabilities of this approach by focusing on three cases: (i) nano-scale carbide precipitation during low-temperature tempering of martensitic steels, (ii) formation of transformation-induced geometrically necessary dislocations in a dual-phase steel during intercritical annealing, and (iii) the partial recrystallization of a metastable β-Ti alloy. - Highlights: • A multi-probe method to track microstructures during heat treatment is developed. • It enables the analysis of various complex phenomena, even those at atomistic scale. • It circumvents some of the free surface effects of classical in-situ experiments.

36 MATERIALS SCIENCE↗

Microstructure stability of ultra-fine grained magnesium alloy AZ31 processed by extrusion and equal-channel angular pressing (EX–ECAP)

Thermal stability of the ultra-fine grained (UFG) microstructure of magnesium AZ31 alloy was investigated. UFG microstructure was achieved by a combined two-step severe plastic deformation process: the extrusion (EX) and subsequent equal-channel angular pressing (ECAP). This combined process leads to refined microstructure and enhanced microhardness. Specimens with UFG microstructure were annealed isochronally at temperatures 150–500 °C for 1 h. The evolution of microstructure, mechanical properties and dislocation density was studied by electron backscatter diffraction (EBSD), microhardness measurements and positron annihilation spectroscopy (PAS). The coarsening of the fine-grained structure at higher temperatures was accompanied by a gradual decrease of the microhardness and decrease of dislocation density. Mechanism of grain growth was studied by general equation for grain growth and Arrhenius equation. Activation energies for grain growth were calculated to be 115, 33 and 164 kJ/mol in temperature ranges of 170–210 °C, 210–400 °C and 400–500 °C (443–483 K, 483–673 K and 673–773 K), respectively. - Highlights: • Microhardness of UFG AZ31 alloy decreases with increasing annealing temperature. • This fact has two reasons: dislocation annihilations and/or grain growth. • The activation energies for grain growth were calculated for all temperature ranges.

36 MATERIALS SCIENCE↗

Enhancing Formability of AA2219 Aluminum Alloy Friction Stir Welded Blanks with Preheating Treatment

The deformation behaviors of FSW blank are complicated due to the incompatibility of the mechanical property and microstructure for the weld and base material. In order to improve the formability of friction stir welded (FSW) blanks, the weld and base material in this paper were subjected to preheating treatments of 250, 300, 350, 400, and 450 °C, plus a solution treatment of 535 °C. The deformation behavior of the AA2219 FSW blank was characterized using uniaxial tension, microhardness test, hydro-bulging test and electron backscattered diffraction to determine the relationship of the deformation property and microstructure for the FSW blanks. Full strain fields of the tensile and bulging specimens were used to analyze the deformation uniformity of the weld and base material under uniaxial tension and biaxial tension stress states. With the limiting bulging height under various preheating temperatures, the formability behavior of the weld and base material was analyzed during the whole bulging process. The optimum preheating temperature can increase the formability and refrain from abnormal grain growth of the weld on the premise of maintaining the weld strength. The limiting bulging height of FSW blank is obviously improved by the lower preheating temperature from 300 to 350 °C. Additionally, the weld position has a significant impact on the deformation of the whole FSW blanks.

36 MATERIALS SCIENCE↗