Search NASA⌕ Search

SEARCH · Search NASA

Results for “engineered matrix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Enhancing CMC Temperature Performance in High Hydrogen Environments using Field Assisted Sintering Technology

This final report summarizes the developments in field assisted sintering technology (FAST) for rapid fabrication of ceramic matrix composite (CMC) materials with integrated environmental barrier coatings (EBCs), as well as their performance in a representative gas turbine combustor environment including stagnant flame zones, and high velocity product zones. CMCs are a possible high temperature tolerant material system for gas turbine engines, which are currently the dominant source of electric power production and the primary source of aircraft propulsion. However, CMCs are costly and time-consuming (on the order of weeks to months) to fabricate, and CMCs based on silicon carbide (SiC) ceramics are susceptible to water vapor degradation requiring the use of specialized EBCs. The manufacturing technique known as FAST can create consolidated parts in as little as a few hours using high pressure and temperature, and may be useful to integrate EBCs into CMCs directly during consolidation.

08 HYDROGEN↗
DOE OSTI2021

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Unhinging the Surfaces of Higher-Order Topological Insulators and Superconductors

Here, we show that the chiral Dirac and Majorana hinge modes in three-dimensional higher-order topological insulators (HOTIs) and superconductors (HOTSCs) can be gapped while preserving the protecting C$_{2n}\mathcal{T}$ symmetry upon the introduction of non-Abelian surface topological order. In both cases, the topological order on a single side surface breaks time-reversal symmetry, but appears with its time-reversal conjugate on alternating sides in a C$_{2n}\mathcal{T}$ preserving pattern. In the absence of the HOTI/HOTSC bulk, such a pattern necessarily involves gapless chiral modes on hinges between C$_{2n}\mathcal{T}$-conjugate domains. However, using a combination of K -matrix and anyon condensation arguments, we show that on the boundary of a 3D HOTI/HOTSC these topological orders are fully gapped and hence “anomalous.” Our results suggest that new patterns of surface and hinge states can be engineered by selectively introducing topological order only on specific surfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Microstructural Changes and Chemical Analysis of Fission Products in Irradiated Uranium-7 wt.% Molybdenum Metallic Fuel Using Atom Probe Tomography

Understanding the microstructural and phase changes occurring during irradiation and their impact on metallic fuel behavior is integral to research and development of nuclear fuel programs. This paper reports systematic analysis of as-fabricated and irradiated low-enriched U-Mo (uranium-molybdenum metal alloy) fuel using atom probe tomography (APT). This study is carried out on U-7 wt.% Mo fuel particles coated with a ZrN layer contained within an Al matrix during irradiation. The dispersion fuel plates from which the fuel samples were extracted are irradiated at Belgian Nuclear Research Centre (SCK CEN) with burn-up of 52% and 66% in the framework of the SELENIUM (Surface Engineering of Low ENrIched Uranium-Molybdenum) project. The APT studies on U-Mo particles from as-fabricated fuel plates enriched to 19.8% revealed predominantly γ-phase U-Mo, along with a network of the cell boundary decorated with α-U, γ’-U2Mo, and UC precipitates along the grain boundaries. The corresponding APT characterization of irradiated fuel samples showed formation of fission gas bubbles enriched with solid fission products. The intermediate burnup sample showed a uniform distribution of the typical bubble superlattice with a radius of 2 nm arranged in a regular lattice, while the high burnup sample showed a non-uniform distribution of bubbles in grain-refined regions. There was no evidence of remnant α-U, γ’-U2Mo, and UC phases in the irradiated U-7 wt.% Mo samples.

Bachhav, Mukesh↗
DOE OSTI2022

Analytical homogenization techniques applied to the Fickian diffusion: Effective diffusivity coefficient

For multiple applications in nuclear energy, the ability to accurately represent material behavior with a simplified model is important to facilitate practical engineering-scale simulations. In this work, we focus on the homogenized thermal response of a medium containing spherical inclusions, similar to a fuel form (compact or pebble) containing TRISO particles. An extensive survey on effective thermal conductivity modeling was performed in our previous study, considering a random distribution of mono-sized spherical inclusions in a continuous matrix. Using the analogy between heat conduction and the simplified Fickian diffusion (or fission product species conservation), we can use the same analytical homogenization methods to obtain ETC as for the effective diffusivity coefficient (EDC). We performed several numerical experiments at varying conditions to assess the validity of our hypothesis for EDC calculations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

PV Inverter Systems Enabled by Monolithically Integrated SiC based Four Quadrant Power Switch (4-QPS) [BiDFET]

The purpose of this project was to develop a new breed of Power Conversion Systems (PCS) for PV integration that is enabled by the newly developed 4-Quadrant Single Die SiC Power Semiconductor Switches (4-QPS) or also referred to as “Bidirectional FET (BIDFET)”. This work includes semiconductor die development, advanced packaging, converter design, development, and testing of 4-QPS enabled hardware prototypes at 1 kW (for single phase residential application) and 10 kW (for three phase commercial application). The BiDirectional Field-Effect Transistor (BiDFET) can enable circuit topologies requiring four-quadrant switches, that were earlier designed using discrete combinations of MOSFETs, IGBTs, GaN HEMTs, and PiN diodes. The monolithic nature of the BiDFET allows lower device count, smaller switch volume, lower inductance, and simpler packaging, and hence more reliable and commercially viable implementation in power electronics converters. The matrix converter topologies, now feasible using BiDFETs, can eliminate the bulky and unreliable dc link capacitors or inductors required for conventional voltage-source or current-source converters in ac–ac and ac–dc applications. The 1.2 kV BiDFET has the potential to disrupt all the applications utilizing 1.2 kV switches, including electric vehicle (EV) drivetrain, bidirectional EV chargers, industrial motor drives, solid-state transformers, datacenter power supplies, elevator drives, dc microgrids, energy storage grid integration, solid-state breakers, etc.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Preferred Void Orientation in Uniaxially Pressed PBX 9502

Ultra- and small-angle neutron scattering techniques were used to study the morphology of voids in directions parallel and perpendicular to the compaction plane of a uniaxially pressed cylinder of PBX 9502. Two-dimensional scattering patterns from samples cut parallel to the compaction plane had circular equal-intensity contours, implying that along this view the voids are circular or randomly oriented. Identical measurements of samples cut perpendicular to the compaction plane produced elliptical equal-intensity contours, indicating preferred orientation of voids. Analysis of the two dimensional scattering patterns confirmed that the voids are non-spherical with an average aspect ratio of 1.20, flattened so that the larger dimensions of the voids lie within the compaction plane. Model analysis of the combined ultra- and small-angle neutron scattering curves revealed that the PBX 9502 porosity is interconnected, in the form of aggregates comprised of non-spherical, primary voids. The volume dimension was found to be the same in both directions, indicating that the aggregate is randomly oriented throughout the sample, and that it is the primary voids that are preferentially oriented. Furthermore, void interfaces with the surrounding matrix were found to be rough or polydisperse, with a common roughness dimension or polydispersity in all directions.

42 ENGINEERING↗
DOE OSTI2020

Dual heterogeneous structures lead to ultrahigh strength and uniform ductility in a Co-Cr-Ni medium-entropy alloy

Alloys with ultra-high strength and sufficient ductility are highly desired for modern engineering applications but difficult to develop. Here we report that, by a careful controlling alloy composition, thermomechanical process, and microstructural feature, a Co-Cr-Ni-based medium-entropy alloy (MEA) with a dual heterogeneous structure of both matrix and precipitates can be designed to provide an ultra-high tensile strength of 2.2 GPa and uniform elongation of 13% at ambient temperature, properties that are much improved over their counterparts without the heterogeneous structure. Electron microscopy characterizations reveal that the dual heterogeneous structures are composed of a heterogeneous matrix with both coarse grains (10~30 μm) and ultra-fine grains (0.5~2 μm), together with heterogeneous L1 2 -structured nanoprecipitates ranging from several to hundreds of nanometers. The heterogeneous L1 2 nanoprecipitates are fully coherent with the matrix, minimizing the elastic misfit strain of interfaces, relieving the stress concentration during deformation, and playing an active role in enhanced ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Roadmap for thermal property measurements of Molten Salt Reactor systems

Thermal properties of molten salts, both with and without fissile and fertile material, are fundamental to modeling and simulation that supports design, construction, operation, and accident progression evaluation of molten salt reactors. This roadmap provides guidance to the research community on the types and amounts of required data for base, or carrier, salt systems, recommends simulated burnup fuel salt compositions to evaluate, and provides a technical foundation for a focused salt property evaluation matrix. The property values generated from both computation and experimental methods are used to develop models that constitute the Molten Salt Thermal Properties Database (MSTDB). While the building blocks of MSTDB are fundamental in nature, its data facilitates constructing engineering models that allow stakeholders to investigate the behavior of specific compositions of interest and supports broader modeling and simulation of MSRs through coupling to multi-physics, multi-scale mass accountancy tools.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Assessing Composite Structure in Metal–Organic Framework-Polymer Mixed-Matrix Membranes

Metal-organic frameworks (MOFs) are renowned for their tunable structure, porosity, and internal chemistry, with demonstrated applications in molecular separations, storage, and conversion. While they are widely usable, the powdery characteristics of MOF materials can be limiting for large-scale processing and implementation in devices. Incorporating MOF particles into polymer supports affords engineering solutions to overcome these issues, yet the nature of the resulting composites is difficult to assess. Here, in this work, we present spectroscopic and calorimetric methods that we believe help establish a holistic physicochemical picture of the composite structure using a series of Zr MOFs with different pore sizes as a testbed. Power law decays are observed in X-ray scattering profiles in low q-space ranging between 2.4 and 3.3, which we interpret as changes in scattering due to polymer infiltrating MOF particles. This interpretation is supported by solid-state nuclear magnetic resonance spectroscopy and differential scanning calorimetry measurements that identify populations of the MOF-associated polymer. Additionally, positron annihilation lifetime spectroscopy measurements collected on a series of composites with different MOF-polymer ratios show multiple decay constants, each correlated to a different free volume elements. In combination with the spectroscopic, calorimetric, and scattering results, we utilize the trends in decay constants as a function of polymer mass fraction to hypothesize a polymer infiltration mechanism whereby large pores are preferentially filled, followed by small pores and, later still, interstitial spaces between particles. Even with vigorous investigation of polymer, MOF, and interface characteristics, the complex and heterogeneous nature of the composites makes absolute structural assertions difficult. We envision that the approaches demonstrated here will be a useful foundation to assess and ultimately guide the design of future MOF-polymer composites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Assessment of the Phase-to-Ground Fault Apparent Admittance Method with Phase/Ground Boundaries to Detect Types of Electrical Faults for Protective Relays Using Signature Library and Simulated Events

Protective relays in electric power grids recognize the types of electrical faults in a few seconds. The most common detection method to detect the types of electrical faults is based on measuring the angle between the zero and negative sequence currents. However, it is not completely accurate because the phase-to-phase-ground and phase-to-ground electrical faults could have the same detection conditions. Therefore, engineers need to plot the events after an electrical fault to observe the nature of the incidents in detail. In this study, the phase-to-ground fault apparent (PGFA) admittance method with phase/ground boundaries identified the types of electrical faults located in distribution power lines and feeders. This method was based on measuring the PGFA admittance magnitudes for the faulted and nonfaulted phases, resulting in greater than zero and near zero, respectively. The PGFA admittance algorithm was built with MATLAB/Simulink software and tested with signature library and grid simulation events. The PGFA method with phase/ground boundaries was evaluated with the confusion matrix. The measured and predicted values matched in more than 90% of the tests, and the PGFA admittance method with phase/ground boundaries presented an accuracy of 94.3% and a precision of 100%.

42 ENGINEERING↗
DOE OSTI2021

Moisture-induced autonomous surface potential oscillations for energy harvesting

A variety of autonomous oscillations in nature such as heartbeats and some biochemical reactions have been widely studied and utilized for applications in the fields of bioscience and engineering. Here, we report a unique phenomenon of moisture-induced electrical potential oscillations on polymers, poly([2-(methacryloyloxy)ethyl] dimethyl-(3-sulfopropyl) ammonium hydroxide-co-acrylic acid), during the diffusion of water molecules. Chemical reactions are modeled by kinetic simulations while system dynamic equations and the stability matrix are analyzed to show the chaotic nature of the system which oscillates with hidden attractors to induce the autonomous surface potential oscillation. Using moisture in the ambient environment as the activation source, this self-excited chemoelectrical reaction could have broad influences and usages in surface-reaction based devices and systems. As a proof-of-concept demonstration, an energy harvester is constructed and achieved the continuous energy production for more than 15,000 seconds with an energy density of 16.8 mJ/cm 2 . A 2-Volts output voltage has been produced to power a liquid crystal display toward practical applications with five energy harvesters connected in series.

42 ENGINEERING↗
DOE OSTI2025

Shifting the MLCT of d 6 metal complexes to the red and NIR

Light-active d 6 -coordination compounds hold great promise for light energy conversion, sensors and therapeutic applications. However, the activity in the red-to-NIR spectral region is highly desirable to convert solar light more efficiently, use low-cost red-light sources and activate these chromophores in biological tissue environment. Due to their versatility, tunability and broad intense absorption, d 6 -coordination compounds with metalto-ligand charge transfer (MLCT) transitions are especially interesting. This review article offers a comprehensive collection of strategies to tune MLCT excited states in d 6 metal complexes and gives insights on group 6 to group 9 transition metals and their respective state-of-the-art MLCT engineering towards red-shifted absorption and emission properties with long-lived excited states. Strategies comprise lowering the π* level of the ligands, destabilizing and mixing of the metal-based HOMO, switching within a group of transition metals, matrix effects and insights into dealing with excited state deactivation in the context of the energy gap law.

Metal to ligand charge transfer (MLCT)↗
DOE OSTI2025

Embedded 3D printing of isotropically enhanced lattice structure with programmable elasticity via three-dimensional fiber alignment

Engineered composites with fiber orientation in a complete three-dimensional (3D) context are highly desired for maximizing structural performance as they mimic the well-organized fiber arrangement in natural composites. However, most fabrication techniques lack the capability for through-plane (z-axis) alignment, limiting the possibility for structural design and performance optimization. In this study, we present an embedded 3D printing approach that enables complete 3D fiber alignment, including region-specific alignment control along the through-plane direction. Our method utilizes the extrusion and suspension of composite inks within a supporting matrix. By regionally adjusting the ink extrusion rate and nozzle translation rate, we locally manipulated the fiber arrangement within the composite 3D architecture. Here, we demonstrate that the 3D alignment of carbon fibers in a structural composite significantly enhances both mechanical properties and thermal conductivity in the in-plane and through-plane directions. Furthermore, by strategically arranging regional fiber orientations within micro-architected materials, we fabricated metamaterial engineered composites with programmable anisotropy ratio and directional moduli.

36 MATERIALS SCIENCE↗
DOE OSTI2021

CSPlib

This computational singular perturbation library (CSPlib) software is useful for analysis of chemical kinetic systems. The code is used to analyze and describe the dynamical landscape underlying the time evolution of a chemical system. Given a database of state vectors, it allows the analysis of the source term and Jacobian matrix of the chemical system, the identification and decoupling of fast and slow processes, and the analysis of cause-and-effect relationships in the coupled system dynamics. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. SAND2021-2391 O

Najm, HabibN.↗
DOE OSTI2022

Two-stage combustor

A two-stage combustor having as constituent parts: a partial oxidation reactor, which catalytically converts a hydrocarbon fuel and a first supply of oxidant into a gaseous partial oxidation product; and a deep oxidation reactor having a premixer plenum fluidly connected to a porous heat spreader, which converts the gaseous partial oxidation product to deep oxidation products. In one embodiment, the premixer plenum provides an empty space wherein combustion occurs in flame mode. In a second embodiment, the premixer plenum contains a high pore density foam matrix, absent catalyst, which facilitates holding a flameless combustion downstream within the porous heat spreader. In both embodiments heat produced during combustion is transmitted from the heat spreader to an associated heat acceptor, such as a heater head of a Stirling engine.

Roychoudhury, Subir↗