Results for “entry reconstruction” — Page 14

NASA NTRSDate not supplied

Attitude Reconstruction of Free-Flight CFD Generated Trajectories Using Non-Linear Pitch Damping Coefficient Curves

Attitude history reconstruction of Free-flight CFD generated trajectories with non-linear pitch damping coefficient curves is investigated. Free-flight CFD simulations of the capsule shape used for the Genesis sample return mission and the upcoming Dragonfly mission to Titan are conducted for 1-, 2-, and 3-degree-of-freedom cases. Two different data reduction methodologies are employed to derive a pitch damping curve as a function of instantaneous angle of attack. These curves are then used to reconstruct the attitude history of the body which is compared to the raw simulation results. While both data reduction methods produce pitch damping curves that can generally reconstruct the motion seen in the Free-flight simulations, it is found that optimization of the pitch damping curve using an inverse estimation process yields superior and more generalizable results. Further refinement of this technique could allow pitch damping curves derived using CFD to serve as a capability complementary to existing techniques for dynamic stability characterization.

entry↗

NASA NTRS2015

Post-Flight Analysis of the Guidance, Navigation, and Control Performance During Orion Exploration Flight Test 1

The first test flight of the Orion Multi-Purpose Crew Vehicle presented additional challenges for guidance, navigation and control as compared to a typical re-entry from the International Space Station or other Low Earth Orbit. An elevated re-entry velocity and steeper flight path angle were chosen to achieve aero-thermal flight test objectives. New IMU's, a GPS receiver, and baro altimeters were flight qualified to provide the redundant navigation needed for human space flight. The guidance and control systems must manage the vehicle lift vector in order to deliver the vehicle to a precision, coastal, water landing, while operating within aerodynamic load, reaction control system, and propellant constraints. Extensive pre-flight six degree-of-freedom analysis was performed that showed mission success for the nominal mission as well as in the presence of sensor and effector failures. Post-flight reconstruction analysis of the test flight is presented in this paper to show whether that all performance metrics were met and establish how well the pre-flight analysis predicted the in-flight performance.

Barth, Andrew↗

NASA NTRS1997

Low-Density Aerodynamics of the Stardust Sample Return Capsule

The aerodynamics of the Stardust Sample Return Capsule are analyzed in the low- density, transitional flow regime using free-molecular, Direct Simulation Monte Carlo, Navier-Stokes, and Newtonian methods to provide inputs for constructing a transitional flow bridging relation. The accuracy of this bridging relation in reconstructing the aero- dynamic coefficients given by the more exact methods is presented for a range of flight conditions and vehicle attitudes. There is good agreement between the various prediction methods, and a simple sine-squared bridging relation is shown to provide a reasonably good description of the axial force, normal force, and pitching moment over a range of Knudsen numbers from 0.001 to 10. The predictions show a static instability of the Star- dust capsule in the free-molecular regime that persists well into the transitional flow. The addition of a thin disk to the base of the capsule is shown to remove this static instability. However, the extremely high entry velocity of 12.6 km/s for the proposed trajectory introduces difficult design issues for incorporating this disk caused by the high aerothermal loads that occur even under relatively rarefied conditions.

Wilmoth, Richard G.↗

NASA NTRS2021

Mars 2020 Perseverance trajectory reconstruction and performance from launch through landing

The Mars 2020 (M2020) Mission carrying Perseverance, the most advanced rover ever sent to Mars, successfully launched on an Atlas V 541 (AV-088) launch vehicle from the Eastern Test Range (ETR) at Cape Canaveral Air Force Station (CCAFS) in Florida at 11:50:00 UTC (T-Zero time) on July 30, 2020. After some station reconfiguration, carrier/telemetry were locked at both Deep Space Network (DSN) Canberra and Goldstone stations. Perseverance entered the Martian atmosphere at 20:36:50 Spacecraft Event Time (SCET) UTC, and landed inside Jezero Crater at 20:43:49 SCET UTC on February 18, 2021. Confirmation of nominal landing was received at the DSN Goldstone and Madrid tracking stations via the Mars Reconnaissance Orbiter at 20:55:11 Earth Received Time (ERT) UTC. This paper summarizes in detail the actual vs. predicted performance in terms of launch vehicle events, launch vehicle injection performance, actual DSN spacecraft lockup, trajectory correction maneuver performance, Entry, Descent, and Landing events, and overall trajectory and geometric characteristics.

Abilleira, Fernando↗

NASA NTRS2021

Mars 2020 Perseverance Trajectory Reconstruction and Performance from Launch through Landing

The Mars 2020 (M2020) Mission carrying Perseverance, the most advanced rover ever sent to Mars, successfully launched on an Atlas V 541 (AV-088) launch vehicle from the Eastern Test Range (ETR) at Cape Canaveral Air Force Station (CCAFS) in Florida at 11:50:00 UTC (T-Zero time) on July 30, 2020. After some station reconfiguration, carrier/telemetry were locked at both Deep Space Network (DSN) Canberra and Goldstone stations. Perseverance entered the Martian atmosphere at 20:36:50 Spacecraft Event Time (SCET) UTC, and landed inside Jezero Crater at 20:43:49 SCET UTC on February 18, 2021. Confirmation of nominal landing was received at the DSN Goldstone and Madrid tracking stations via the Mars Reconnaissance Orbiter at 20:55:11 Earth Received Time (ERT) UTC. This paper summarizes in detail the actual vs. predicted performance in terms of launch vehicle events, launch vehicle injection performance, actual DSN spacecraft lockup, trajectory correction maneuver performance, Entry, Descent, and Landing events, and overall trajectory and geometric characteristics.

Wong, Mau↗

NASA NTRSDate not supplied

Investigating Photogrammetric Accuracy of a Lunar-lander-induced Crater Measurement System

Laboratory measurements have been made to validate the performance of the Stereo CAmeras for Lunar Plume-Surface Studies (SCALPSS) stereo photogrammetry systems which will be flying to the moon on two of NASA’s upcoming Commercial Lunar Payload Services (CLPS) missions. Until recently, the system’s accuracy had only been studied using idealized geometric shapes as measurement targets. A realistic crater model of representative scale and an idealized ‘staircase’ target have been used to compare measurement accuracy of ideal versus lunar-like objects, with the commercial V-STARS® system being used to provide the known reference values for comparison. In a parametric study, altitude, lens focal length, and camera separation are varied to assess each parameter’s impact on photogrammetric accuracy in relation to the scaling law prediction developed previously. The SCALPSS 1.0 and 1.1 configurations have been validated on the crater model within acceptable accuracy for the missions, performing significantly better than the scaling law prediction in some cases. A semi-automated post-processing routine was developed in MATLAB® and proved successful for the cross-correlation of features between two stereo images. For some cases of extreme convergence angles between a camera pair, manual feature detection and matching was required. By using this manual process, the crater depth map was reconstructed but with worse accuracy than the idealized staircase measurements; refinements to the processing algorithm are expected to improve future results. Also examined in this work is the impact of illumination environments, both natural (e.g., Sun angles) and artificial (diffuse or structured illumination sources), on the camera system’s ability to measure the erosion of the lunar terrain.

Plume-surface interaction↗

NASA NTRSDate not supplied

Investigating Photogrammetric Accuracy of a Lunar-lander-induced Crater Measurement System

Laboratory measurements have been made to validate the performance of the Stereo CAmeras for Lunar Plume-Surface Studies (SCALPSS) stereo photogrammetry systems which will be flying to the moon on two of NASA’s upcoming Commercial Lunar Payload Services (CLPS) missions. Until recently, the system’s accuracy had only been studied using idealized geometric shapes as measurement targets. A realistic crater model of representative scale and an idealized ‘staircase’ target have been used to compare measurement accuracy of ideal versus lunar-like objects, with the commercial V-STARS® system being used to provide the known reference values for comparison. In a parametric study, altitude, lens focal length, and camera separation are varied to assess each parameter’s impact on photogrammetric accuracy in relation to the scaling law prediction developed previously. The SCALPSS 1.0 and 1.1 configurations have been validated on the crater model within acceptable accuracy for the missions, performing significantly better than the scaling law prediction in some cases. A semi-automated post-processing routine was developed in MATLAB® and proved successful for the cross-correlation of features between two stereo images. For some cases of extreme convergence angles between a camera pair, manual feature detection and matching was required. By using this manual process, the crater depth map was reconstructed but with worse accuracy than the idealized staircase measurements; refinements to the processing algorithm are expected to improve future results. Also examined in this work is the impact of illumination environments, both natural (e.g., Sun angles) and artificial (diffuse or structured illumination sources), on the camera system’s ability to measure the erosion of the lunar terrain.

Plume-surface interaction↗

NASA NTRS2008

Aerodynamics for the Mars Phoenix Entry Capsule

Pre-flight aerodynamics data for the Mars Phoenix entry capsule are presented. The aerodynamic coefficients were generated as a function of total angle-of-attack and either Knudsen number, velocity, or Mach number, depending on the flight regime. The database was constructed using continuum flowfield computations and data from the Mars Exploration Rover and Viking programs. Hypersonic and supersonic static coefficients were derived from Navier-Stokes solutions on a pre-flight design trajectory. High-altitude data (free-molecular and transitional regimes) and dynamic pitch damping characteristics were taken from Mars Exploration Rover analysis and testing. Transonic static coefficients from Viking wind tunnel tests were used for capsule aerodynamics under the parachute. Static instabilities were predicted at two points along the reference trajectory and were verified by reconstructed flight data. During the hypersonic instability, the capsule was predicted to trim at angles as high as 2.5 deg with an on-axis center-of-gravity. Trim angles were predicted for off-nominal pitching moment (4.2 deg peak) and a 5 mm off-axis center-ofgravity (4.8 deg peak). Finally, hypersonic static coefficient sensitivities to atmospheric density were predicted to be within uncertainty bounds.

Edquist, Karl T.↗

NASA NTRS2016

Orion Exploration Flight Test Reaction Control System Jet Interaction Heating Environment from Flight Data

The Orion Multi-Purpose Crew Vehicle (MPCV) Reaction Control System (RCS) is critical to guide the vehicle along the desired trajectory during re-‐entry. However, this system has a significant impact on the convective heating environment to the spacecraft. Heating augmentation from the jet interaction (JI) drives thermal protection system (TPS) material selection and thickness requirements for the spacecraft. This paper describes the heating environment from the RCS on the afterbody of the Orion MPCV during Orion's first flight test, Exploration Flight Test 1 (EFT-1). These jet plumes interact with the wake of the crew capsule and cause an increase in the convective heating environment. Not only is there widespread influence from the jet banks, there may also be very localized effects. The firing history during EFT-1 will be summarized to assess which jet bank interaction was measured during flight. Heating augmentation factors derived from the reconstructed flight data will be presented. Furthermore, flight instrumentation across the afterbody provides the highest spatial resolution of the region of influence of the individual jet banks of any spacecraft yet flown. This distribution of heating augmentation across the afterbody will be derived from the flight data. Additionally, trends with possible correlating parameters will be investigated to assist future designs and ground testing programs. Finally, the challenges of measuring JI, applying this data to future flights and lessons learned will be discussed.

White, Molly E.↗

NASA NTRS2013

2011 Mars Science Laboratory Trajectory Reconstruction and Performance from Launch Through Landing

The Mars Science Laboratory (MSL) mission successfully launched on an Atlas V 541 Expendable Evolved Launch Vehicle (EELV) from the Eastern Test Range (ETR) at Cape Canaveral Air Force Station (CCAFS) in Florida at 15:02:00 UTC on November 26th, 2011. At 15:52:06 UTC, six minutes after the MSL spacecraft separated from the Centaur upper stage, the spacecraft transmitter was turned on and in less than 20 s spacecraft carrier lock was achieved at the Universal Space Network (USN) Dongara tracking station located in Western Australia. MSL, carrying the most sophisticated rover ever sent to Mars, entered the Martian atmosphere at 05:10:46 SpaceCraft Event Time (SCET) UTC, and landed inside Gale Crater at 05:17:57 SCET UTC on August 6th, 2012. Confirmation of nominal landing was received at the Deep Space Network (DSN) Canberra tracking station via the Mars Odyssey relay spacecraft at 05:31:45 Earth Received Time (ERT) UTC. This paper summarizes in detail the actual vs. predicted trajectory performance in terms of launch vehicle events, launch vehicle injection performance, actual DSN/USN spacecraft lockup, trajectory correction maneuver performance, Entry, Descent, and Landing events, and overall trajectory and geometry characteristics.

trajectory↗

NASA NTRS2020

InSight Aerothermal Environment Assessment

The Mars Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) spacecraft, which successfully touched down on the planet surface on November 26, 2018, was proposed as a near build-to-print copy of the Mars Phoenix vehicle to reduce the overall cost and risk of the mission. Since the lander payload and the atmospheric entry trajectory were similar enough to those of the Phoenix mission, it was expected that the Phoenix thermal protection material thickness would be sufficient to withstand the entry heat load. However, allowances were made for increasing the heatshield thickness because the planned spacecraft arrival date coincided with the Mars dust storm season. The aftbody Thermal Protection System (TPS) components were not expected to change. In a first for a US Mars mission, the aerothermal environments for InSight included estimates of radiative heat flux to the aftbody from the wake. The combined convective and radiative heat fluxes were used to determine if the as-flown Phoenix thermal protection system (TPS) design would be sufficient for InSight. Although the radiative heat fluxes on the aftbody were predicted to be comparable to, or even higher than the local convective heat fluxes, all analyses of the aftbody TPS showed that the design would still be adequate. Aerothermal environments were computed for the vehicle from post-flight reconstruction of the atmosphere and trajectory and compared.

Beck, Robin↗

NASA NTRS2020

InSight Aerothermal Environment Assessment

The Mars Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) spacecraft, which successfully touched down on the planet surface on November 26, 2018, was proposed as a near build-to-print copy of the Mars Phoenix vehicle to reduce the overall cost and risk of the mission. Since the lander payload and the atmospheric entry trajectory were similar enough to those of the Phoenix mission, it was expected that the Phoenix thermal protection material thickness would be sufficient to withstand the entry heat load. However, allowances were made for increasing the heatshield thickness because the planned spacecraft arrival date coincided with the Mars dust storm season. The aftbody Thermal Protection System (TPS) components were not expected to change. In a first for a US Mars mission, the aerothermal environments for InSight included estimates of radiative heat flux to the aftbody from the wake. The combined convective and radiative heat fluxes were used to determine if the as-flown Phoenix thermal protection system (TPS) design would be sufficient for InSight. Although the radiative heat fluxes on the aftbody were predicted to be comparable to, or even higher than the local convective heat fluxes, all analyses of the aftbody TPS showed that the design would still be adequate. Aerothermal environments were computed for the vehicle from post-flight reconstruction of the atmosphere and trajectory and compared with the design environments. These comparisons showed that the predicted as-flown conditions were less severe than the design conditions.

Beck, Robin A. S.↗

NASA NTRS2016

Mars 2020 Entry, Descent and Landing Instrumentation 2 (MEDLI2)

The Mars Entry Descent and Landing Instrumentation 2 (MEDLI2) sensor suite will measure aerodynamic, aerothermodynamic, and TPS performance during the atmospheric entry, descent, and landing phases of the Mars 2020 mission. The key objectives are to reduce design margin and prediction uncertainties for the aerothermal environments and aerodynamic database. For MEDLI2, the sensors are installed on both the heatshield and backshell, and include 7 pressure transducers, 17 thermal plugs, and 3 heat flux sensors (including a radiometer). These sensors will expand the set of measurements collected by the highly successful MEDLI suite, collecting supersonic pressure measurements on the forebody, a pressure measurement on the aftbody, direct heat flux measurements on the aftbody, a radiative heating measurement on the aftbody, and multiple near-surface thermal measurements on the thermal protection system (TPS) materials on both the forebody and aftbody. To meet the science objectives, supersonic pressure transducers and heat flux sensors are currently being developed and their qualification and calibration plans are presented. Finally, the reconstruction targets for data accuracy are presented, along with the planned methodologies for achieving the targets.

Aerodynamics↗

NASA NTRS2018

A Case for High-Fidelity Material Response Modeling

Material response modeling of heatshields for planetary entry vehicles has remained largely unchanged since Aerotherm Corp. introduced the CMA program in 1967. Modern models, like FIAT, have tread the same path, introducing efficiencies and better material property data along the way, but otherwise following the same underlying model paradigm. The CMA approach has worked well for heatshield design up to this point. However, there are three motivations for the material response community to pursue higher fidelity beyond simplified, CMA-derived models. The first motivation is that missions are becoming increasingly demanding and complex and, as they do, confidence in simplified models naturally decreases. Second, reliability of materials is now as much or more of a driving concern for mission designers than thermal response. Third, NASA and other agencies are increasingly interested in flight instrumentation for engineering science. This latter motivation places far stricter requirements on model accuracy in order to meet requirements for flight environment reconstruction.

Barnhardt, Michael D.↗

NASA NTRS2019

Aerodynamics for the ADEPT SR-1 Flight Experiment

Adaptable, Deployable, Entry, and Placement Technology (ADEPT) is a combination of a heatshield and an aerodynamic decelerator for atmospheric entry applications. The ADEPT Sounding Rocket (SR)-1 mission was a suborbital flight experiment of an 0.7 m-diameter ADEPT to verify system-level performance and to characterize dynamic stability behavior. The aerodynamic database for ADEPT SR-1 was constructed from non-continuum and continuum flowfield computations, along with data from recent ADEPT ground testing and the IRVE-3 flight test vehicle. High-altitude (free-molecular and transitional regimes) data were generated using DSMC methods. Pre-flight predictions of continuum static aerodynamics coefficients were derived from Reynolds-Averaged Navier-Stokes solutions at conditions along a design trajectory, with comparisons to available ground test data of the nano-ADEPT geometry. Dynamic pitch damping characteristics were taken from functional forms developed for the IRVE-3 flight test vehicle through ballistic range testing. Comparison of pre-flight predictions to post-flight reconstruction of aerodynamic force and moment coefficients is presented.

Korzun, Ashley M.↗

NASA NTRS2019

Simulation Schiaparelli's Entry and Comparison to Aerothermal Flight Data

The European Space Agency recently flew an entry, descent, and landing demonstrator module called Schiaparelli that entered the atmosphere of Mars on the 19th of October, 2016. The instrumentation suite included heatshield and backshell pressure transducers and thermocouples (known as AMELIA - Atmospheric Mars Entry and Landing Investigations and Analysis) and backshell radiation and direct heat flux-sensing sensors (known as COMARS (Combined Aerothermal and Radiometer Sensors Instrument Package) and ICOTOM (narrow band radiometers)). Due to the failed landing of Schiaparelli, only a subset of the flight data was transmitted before and after plasma black-out. The goal of this paper is to present comparisons of the flight data with calculations from NASA simulation tools, DPLR (Data Parallel Line Relaxation) / NEQAIR (NonEQuilibrium AIr Radiation) and LAURA (Langley Aerothermodynamic Upwind Relaxation Algorithm) / HARA (High-temperature Aerothermodynamic RAdiation ). DPLR and LAURA are used to calculate the flowfield around the vehicle and surface properties, such as pressure and convective heating. The flowfield data are passed to NEQAIR and HARA to calculate the radiative heat flux. Comparisons will be made to the COMARS total heat flux, radiative heat flux and pressure measurements. Results will also be shown against the reconstructed heat flux which was calculated from an inverse analysis of the AMELIA thermocouple data performed by Astrium. Preliminary calculations are presented in this abstract.

Brandis, A. M.↗

NASA NTRS1998

Reconstruction of the 1994 Pittsburgh Airplane Accident Using a Computer Simulation

On September 8, 1994, a Boeing 737-300 passenger airplane was on a downwind approach to the Pittsburgh International Airport at an altitude of 5000 feet above ground level (6000 feet MSL). While in a shallow left turn onto a downwind approach heading, the airplane crossed into the vortex trail of a Boeing 727 flying in the same approach pattern about 4 miles ahead. The B-737 airplane rolled and turned sharply to the left, exited the vortex wake and plunged into the ground. Weather was not a factor in the accident. The airplane was equipped with a 11+ channel digital Flight Data Recorder (FDR) and a multiple channel Cockpit Voice Recorder (CVR). Both recorders were recovered from the crash site and provided excellent data for the development of an accident scenario. Radar tracking of the two airplanes as well as the indicated air speed (IAS) perturbations clearly visible on the B-737 FDR recordings indicate that the upset was apparently initiated by the airplane's crossing into the wake of the B-727 flying ahead in the same traffic pattern. A 6 degree-of-freedom simulation program for the B-737 airplane using MATLAB and SIMULINK was constructed. The simulation was initialized at the stabilized flight conditions of the airplane about 13 seconds prior to its entry into the vortex trail of the B-727 airplane. By assuming a certain combination of control inputs, it was possible to produce a simulated motion that closely matched that recorded on the FDR.

Parks, Edwin K.↗

NASA NTRS2015

Preserving the Science Legacy from the Apollo Missions to the Moon

Six Apollo missions landed on the Moon from 1969-72, returning to Earth 382 kg of lunar rock, soil, and core samples-among the best documented and preserved samples on Earth that have supported a robust research program for 45 years. From mission planning through sample collection, preliminary examination, and subsequent research, strict protocols and procedures are followed for handling and allocating Apollo subsamples. Even today, 100s of samples are allocated for research each year, building on the science foundation laid down by the early Apollo sample studies and combining new data from today's instrumentation, lunar remote sensing missions and lunar meteorites. Today's research includes advances in our understanding of lunar volatiles, lunar formation and evolution, and the origin of evolved lunar lithologies. Much sample information is available to researchers at curator.jsc.nasa.gov. Decades of analyses on lunar samples are published in LPSC proceedings volumes and other peer-reviewed journals, and tabulated in lunar sample compendia entries. However, for much of the 1969-1995 period, the processing documentation, individual and consortia analyses, and unpublished results exist only in analog forms or primitive digital formats that are either inaccessible or at risk of being lost forever because critical data from early investigators remain unpublished. We have initiated several new efforts to rescue some of the early Apollo data, including unpublished analytical data. We are scanning NASA documentation that is related to the Apollo missions and sample processing, and we are collaborating with IEDA to establish a geochemical database called Moon DB. To populate this database, we are working with prominent lunar PIs to organize and transcribe years of both published and unpublished data. Other initiatives include micro-CT scanning of complex lunar samples to document their interior structure (e.g. clasts, vesicles); linking high-resolution scans of Apollo film products to samples; and new procedures for systematic high resolution photography of samples before additional processing, enabling detailed 3D reconstructions of the samples. All of these efforts will provide comprehensive access to Apollo samples and support better curation of the samples for decades to come.

Evans, Cindy↗