Search NASA⌕ Search

SEARCH · Search NASA

Results for “experimental studies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Experimental study of tail-span effects on a generic canard-controlled missile

An experimental investigation was conducted on a cruciform canard controlled missile configuration to determine the effects of tail span/canard span ratio on controllability. The investigation was conducted over the Mach number range of 1.75 to 3.50. Reductions of tail span/canard span ratio produced lower static margins and higher trim angle of attack. The results show that canard controls can provide pitch- and yaw-control as well as roll-control by proper selection of the tail span/canard span ratio.

Blair, A. B., Jr.↗

Theoretical and Experimental Study of Ignition Lag and Engine Knock

The author believes, on the basis of experimental ignition-lag data, that the character of a fuel cannot be stated in terms of a single constant (such as octane or cetane number) but that at least two and generally three constants are required. Thus no correlation between knock ratings can be expected if in one set of tests the charge temperature was varied while in the other the charge pressure was varied. For this reason, he favors knock rating being based on an equation characterizing the ignition lag of the fuel as a function of pressure and temperature of the charge.

Schmidt, Frtiz A F↗

An experimental study of the flow field surrounding a subsonic jet in a cross flow

An experimental investigation of the flow interaction of a 5.08 cm (2.00 in.) diameter round subsonic jet exhausting perpendicularly to a flat plate in a subsonic cross flow was conducted in the NASA Ames 7x1O ft. Wind Tunnel Number One. Flat plate surface pressures were measured at 400 locations in a 30.48 cm (12.0 in.) concentric circular array surrounding the jet exit. Results from these measurements are provided in tabular and graphical form for jet-to-crossflow velocity ratios ranging from 4 to 12, and for jet exit Mach numbers ranging from 0.50 to 0.93. Laser doppler velocimeter (LDV) three component velocity measurements were made in selected regions in the developed jet plume and near the flat plate surface, at a jet Mach number of 0.50 and jet-to-crossflow velocity ratios of 6 and 8. The results of both pressure and LDV measurements are compared with the results of previous experiments. In addition, pictures of the jet plume shape at jet velocity ratios ranging from 4 to 12 were obtained using schleiren photography. The LDV measurements are consistent with previous work, but more extensive measurements will be necessary to provide a detailed picture of the flow field. The surface pressure results compare closely with previous work and provide a useful characterization of jet induced surface pressures. The results demonstrate the primary influence of jet velocity ratio and the secondary influence of jet Mach number in determining such surface pressures.

Dennis, Robert Foster↗

Experimental Study of the Compression Response of Fluted-Core Composite Panels with Joints

Fluted-core sandwich composites consist of integral angled web members spaced between laminate face sheets, and may have the potential to provide benefits over traditional sandwich composites for certain aerospace applications. However, fabrication of large autoclave-cured fluted-core cylindrical shells with existing autoclaves will require that the shells be fabricated in segments, and joined longitudinally to form a complete barrel. Two different longitudinal fluted-core joint designs were considered experimentally in this study. In particular, jointed fluted-core-composite panels were tested in longitudinal compression because longitudinal compression is the primary loading condition in dry launch-vehicle barrel sections. One of the joint designs performed well in comparison with unjointed test articles, and the other joint design failed at loads approximately 14% lower than unjointed test articles. The compression-after-impact (CAI) performance of jointed fluted-core composites was also investigated by testing test articles that had been subjected to 6 ft-lb impacts. It was found that such impacts reduced the load-carrying capability by 9% to 40%. This reduction is dependent on the joint concept, component flute size, and facesheet thickness.

Schultz, Marc R.↗

An Experimental Study of a Pulsed Electromagnetic Plasma Accelerator

Experiments are being performed on the NASA Marshall Space Flight Center (MSFC) pulsed electromagnetic plasma accelerator (PEPA-0). Data produced from the experiments provide an opportunity to further understand the plasma dynamics in these thrusters via detailed computational modeling. The detailed and accurate understanding of the plasma dynamics in these devices holds the key towards extending their capabilities in a number of applications, including their applications as high power (greater than 1 MW) thrusters, and their use for producing high-velocity, uniform plasma jets for experimental purposes. For this study, the 2-D MHD modeling code, MACH2, is used to provide detailed interpretation of the experimental data. At the same time, a 0-D physics model of the plasma initial phase is developed to guide our 2-D modeling studies.

Thio, Y. C. Francis↗

An experimental study of tone excited heated jets

The objective of this investigation was to obtain detailed experimental data on the effects of upstream acoustic excitation on the mixing of heated jets with the surrounding air. Based on the information gathered in the literature survey, a technical approach was developed to carry out a systematic set of mean flowfield measurements for a broad range of jet operating and acoustic excitation conditions. Most of the results were obtained at Mach numbers of 0.3 and 0.8 and total temperatures of up to 800 K. Some measurements were made also for the fully expanded supersonic jet of Mj = 1.15. The maximum level of excitation was Le equal to or less than 150 dB and a range of excitation frequencies up to fe = 4 kHz was used. The important results derived from this study can be summarized as follows: (1) the sensitivity of heated jets to upstream acoustic excitation varies strongly with the jet operating conditions, (2) the threshold excitation level increases with increasing jet temperature, and (3) the preferred Strouhal number does not change significantly with a change of the jet operating conditions.

Lepicovsky, J.↗

Experimental study of three-dimensional separated flow surrounding a hemisphere-cylinder at incidence

Detailed experimental surface pressure coefficient measurements, obtained for a hemisphere-cylinder-flare model in a low supersonic flow (freestream M = 1.2) at various angles of attack (0 deg to 27.5 deg), have been analyzed. The pressure values for each angle of attack were smoothed and checked against their respective oil-flow photographs. The smoothed results were then used to validate a theory which relates the number and type of singular points observed in the oil-flow patterns with local surface-pressure extrema.

Meade, Andrew J., Jr.↗

Experimental Studies on the Effect of Impact Processes on the Formation and Evolution of Amino Acids

Introduction: A critical step in the emergence of life on Earth was the synthesis of larger organic molecules from simple building blocks such as NH3, CO2, H2O, and CH3OH. The presence of amino acids and other complex organics in comets and meteorites demonstrates that widespread organic synthesis likely occurred across the early solar system. Building on previous work [e.g., 1-3], we systematically explore impact-driven chemical evolution of exogenous organics and their precursors. Collisional processes may also have provided a source of energy for the formation of more complex organics from endogenous building blocks. The high flux of impactors to Earth immediately prior to and during the origins of life suggests that impacts could have played a critical role. Key Questions: 1. How are the formation and evolution of amino acids affected by the presence of a mineral matrix during cometary and asteroidal impacts onto the early Earth? 2. Do some minerals (e.g., phyllosilicates) provide a more robust protective framework or reactive surface site for amino-acid formation and/or polymerization? 3. Does the abundance of ices and/or amino acids relative to that of the mineral matrix affect the formation and evolution of amino acids? 4. Are there impact velocities/shock pressures at which formation or polymerization of amino acids is favored or precluded? Experimental Approach: This study systematically examines the conditions under which amino acids and other organic molecules can form, be polymerized, and/or be destroyed during impact events into particulate regolith simulants. Variable parameters include the modal composition of this regolith (silicate matrices, ratios of ices, silicates, and amino acids) and impact velocities/shock pressures. Impacts experiments were performed using the two-stage light-gas gun (LGG), vertical gun (VG), and flat-plate accelerator (FPA) in the Experimental Impact Lab at JSC. FPA experiments were performed over a range of shock pressures (11.3-31.5 GPa) using CM chondrite simulant mixed with amino acids at ratios of 0:10, 1:10, 1:103, and 1:106 (amino acid:host). Techniques for mixing cometary ices have been optimized and test runs have been performed using the LGG (see figure below). Analysis: Post-impact, samples are heated in water to extract amino acids and peptides. Extracts are characterized via liquid chromatography-mass spectrometry (LC-MS) and the mineralogies of solid residues are characterized using X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Additional LC-MS and mineralogical analyses are underway.

Eve L Berger↗

An experimental study of the lift, drag and static longitudinal stability for a three lifting surface configuration

The experimental procedure and aerodynamic force and moment measurements for wind tunnel testing of the three lifting surface configuration (TLC) are described. The influence of nonelliptical lift distributions on lift, drag, and static longitudinal stability are examined; graphs of the lift coefficient versus angle of attack, the pitching moment coefficient, drag coefficient, and lift to drag ratio versus lift coefficient are provided. The TLC data are compared with the conventional tail-aft configuration and the canard-wing configuration; it is concluded that the TLC has better lift and high-lift drag characteristics, lift to drag ratio, and zero-lift moments than the other two configurations. The effects of variations in forward and tail wind incidence angles, gap, stagger, and forward wind span on the drag, lift, longitudinal stability, and zero-lift moments of the configuration are studied.

Ostowari, C.↗

An experimental study of the validity of the heat-field concept for sonic-boom alleviation

An experimental program was carried out in the NASA-Langley 4 ft x 4 ft supersonic pressure tunnel to investigate the validity of the heat-field concept for sonic boom alleviation. The concept involves heating the flow about a supersonic aircraft in such a manner as to obtain an increase in effective aircraft length and yield an effective aircraft shape that will result in a shock-free pressure signature on the ground. First, a basic body-of-revolution representing an SST configuration with its lift equivalence in volume was tested to provide a baseline pressure signature. Second, a model having a 5/2-power area distribution which, according to theory, should yield a linear pressure rise with no front shock wave was tested. Third, the concept of providing the 5/2-power area distribution by using an off-axis slender fin below the basic body was investigated. Then a substantial portion (approximately 40 percent) of the solid fin was replaced by a heat field generated by passing heated nitrogen through the rear of the fin.

Swigart, R. J.↗

An experimental study of the properties of surface pressure fluctuations in strong adverse pressure gradient turbulent boundary layers

Experimental data were obtained on blade self-noise generation by strong adverse-pressure-gradient attached boundary layers and by separated turbulent boundary layers that accompany stall. Two microphones were calibrated, placed in plastic housing, and installed in a wind tunnel where observations of acoustic and turbulent signals permitted decomposition of the surface pressure fluctuation signals into the propagated acoustic part and the turbulent-flow generated portion. To determine the convective wave speed of the turbulent contributions, the microphones were spaced a small distance apart in the streamwise direction and correlations were obtained. The turbulent surface pressure spectra upstream of detachment and downstream of the beginning of separation are discussed as well as measurements of turbulent velocity spectra and wavespeeds.

Simpson, R. L.↗

An experimental study of correlations in the development of the electron-photon cascades

In terms of the experimental data on the development of the electron photon cascades (EPC) in Pb from electrons and photons of cosmic rays in the tens GeV energy region a calculation of correlations between the characteristics of longitudinal and lateral development of the EPC as well as those between fluctuations of the cascade particle numbers at different stages of the cascade development was carried out. The results obtained are compared to the numerical EPC calculations.

Kratenko, Y. P.↗

Atom beam surface interaction studies: Experimental system development

Quantitative deposition by standard techniques of adsorbates containing C and Si onto selected substrates is studied. The interaction kinetics of a beam of oxygen, nitrogen, or hydrogen atoms of known flux are investigated by Auger electron spectroscopy and LEED. Desborbed molecules will be analyzed by mass spectroscopy using modulated beam techniques. Experimental conditions permitting, two sets of measurements will be correlated.

Gregory, J. C.↗

An experimental study of a three-dimensional shock wave/turbulent boundary-layer interaction at a hypersonic Mach number

Experimental data for a series of three-dimensional shock-wave/turbulent-boundary-layer interaction flows at Mach 8.2 are presented. The test bodies, composed of sharp fins fastened to a flat-plate test surface, were designed to generate flows with varying degrees of pressure gradient, boundary-layer separation, and turning angle. The data include surface-pressure, heat-transfer, and skin-friction distributions, as well as limited mean flowfield surveys both in the undisturbed and interaction regimes. The data were obtained for the purpose of validating computational models of these hypersonic interactions.

Kussoy, M. I.↗

An experimental study of secondary vortex structure in mixing layers

This report covers the first eight months of an experimental research project on the secondary vortex structure in plane mixing layers. The aim of the project is to obtain quantitative data on the behavior of the secondary structure in a turbulent mixing layer at reasonable reynolds numbers (Re(sub delta(sub w)) approx. 50,000). In particular, we hope to resolve the questions of how the scale of the secondary vortex structure changes with the scale of the mixing layer, and whether the structures are fixed in space, or whether they 'meander' in the spanwise direction.

Bell, J. H.↗

Experimental study of a pressure-driven, three-dimensional, turbulent boundary layer

The paper presents the results of an experimental investigation into a strongly-skewed, pressure-driven, three-dimensional turbulent boundary layer. Mean velocity and static pressure measurements reveal the general nature of the flowfield studied, while detailed measurements of the Reynolds stress tensor indicate the effect of the strong pressure field on the turbulent velocities. The rate and magnitude of the skewing in the boundary layer emerge as the most important parameters governing the behavior of the Reynolds stresses.

Anderson, S. D.↗

Experimental Study of Characteristics of Micro-Hole Porous Skins for Turbulent Skin Friction Reduction

Characteristics of micro-hole porous skins for the turbulent skin friction reduction technology called the micro-blowing technique (MBT) were assessed experimentally at Mach 0.4 and blowing fractions from zero to 0.005. The objective of this study was to provide guidelines for the selection of porous plates for MBT. The hole angle, pattern, diameter, aspect ratio, and porosity were the parameters considered for this study. The additional effort to angle and stagger the holes was experimentally determined to be unwarranted in terms of skin friction benefit; therefore, these parameters were systematically eliminated from the parametric study. The impact of the remaining three parameters was evaluated by fixing two parameters at the reference values while varying the third parameter. The best hole-diameter Reynolds number was found to be around 400, with an optimum aspect ratio of about 6. The optimum porosity was not conclusively discerned because the range of porosities in the test plates considered was not great enough. However, the porosity was estimated to be about 15 percent or less.

Hwang, Danny P.↗

An experimental study of a three lifting surface configuration

The aerodynamic ramifications of utilizing three lifting surfaces as opposed to the conventional or canard lifting configurations have been studied on a theoretical basis by previous researchers. This paper presents an experimental investigation of various configuration modifications for an unyawed typical business jet at a Reynolds number of 1.3 million. The three surface has better lift and high-lift drag characteristics than either the canard or tail-aft configurations, but the cruise drag is more. The induced drag at cruise is highest for the canard and lowest for the tail-aft configuration. The pitching moment characteristics are somewhat between those of the canard and tail-aft configurations. A decrease in gap adversely affects the pitching moment characteristics. A smaller stagger leads to better aerodynamic and stability characteristics. A decrease in span of the forward wing gives better cruise drag and longitudinal stability characteristics, but has adverse effects on high-lift drag. A variation in the incidence angles of either or both the forward and aft wings changes the zero-lift moments of the configuration, while marginally affecting overall lift and drag. At cruise, the lift to drag ratio is highest for the conventional and lowest for the three surface. For high lift conditions, the order is reversed.

Ostowari, C.↗