Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large scale, cold flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗
NASA NTRS1974

Acoustic loads on an externally blown flap system due to impingement of a TF-34 jet engine exhaust

One of the powered lift systems currently being considered for use on STOL vehicles obtains additional lift by impinging the flow of a jet exhaust on the flaps and turning it downward. This direct impingement subjects large areas of the flap to the fluctuating pressure loads of the turbulent jet flow; these loads have the potential for causing high vibration levels and sonic fatigue failures. A test was conducted on a full-scale mockup of an externally blown flap system, which consisted of a TF-34 engine and a section of a wing having a triple-slotted flap. Data were obtained and evaluated on the fluctuating pressures on the flaps and it is the purpose of this paper to present some of the results describing the loads.

Schoenster, J. A.↗
NASA NTRS1974

Effect of trailing-edge flap deflection on the lateral and longitudinal-stability characteristics of a supersonic transport model having a highly-swept arrow wing

A low-speed investigation has been made on a highly-swept wing model having a thickened leading edge to determine the effect of inboard trailing-edge flaps on the characteristics of the model in pitch and sideslip. The tests were made at a Mach number of 0.227 which corresponds to a Reynolds number of about 5.53 million based on the reference chord. The results showed that deflection of the trailing-edge flaps decreased the roll due to sideslip by about 20 percent at a landing lift coefficient of 0.5. The directional-stability parameter, was increased by deflection of the flaps and the range of lift coefficients over which it was positive was also increased. The longitudinal stability characteristics of the model without leading-edge devices were improved by increased flap deflection, that is, the pitch-up tendency was delayed to higher lift coefficients. The lift coefficient increment resulting from the 15 deg flap deflection compared favorably with that predicted.

Lockwood, V. E.↗
NASA NTRS1974

Small scale wind tunnel model investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A small-scale wind tunnel test of a two engine hybrid model with upper surface blowing on a simulated expandable duct internally blown flap was accomplished in a two phase program. The low wing Phase I model utilized 0.126c radius Jacobs/Hurkamp flaps and 0.337c radius Coanda flaps. The high wing Phase II model was utilized for continued studies on the Jacobs/Hurkamp flap. Principal study areas included: basic data both engines operative and with an engine out, control flap utilization, horizontal tail effectiveness, spoiler effectiveness, USB nacelle deflector study and USB/IBF pressure ratio effects.

Waites, W. L.↗
NASA NTRS1973

Effect of exhaust nozzle configuration on aerodynamic and acoustic performance of an externally blown flap system with a quiet 6:1 bypass ratio engine

A highly suppressed TF-34 engine was used to investigate engine and flap interaction noise associated with an externally blown flap STOL powered lift system. Noise, efficiency, and velocity decay characteristics of mixed and separate flow exhaust systems including convergent, co-annular, and lobed designs were determined with the engine operating alone. Noise data were then obtained for several of the exhaust configurations with the engine blowing a wing-flap segment. Noise for both the engine alone and the engine with blown flaps showed substantial differences for the various exhaust configurations tested. The differences in observed noise are related primarily to nozzle effective exhaust velocity, flap impingement velocity, and noise spectral shape.

Samanich, N. E.↗
NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large-scale cold-flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, to try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that, with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗
NASA NTRS1974

Vortex-induced heating to cone flaps at Mach 6

Discussion of the local heating effect on the lee-side control flaps of supersonic configurations due to the interaction between vortices and leeward control surfaces at an angle of attack. Considerations are given for an appropriate positioning of control flaps to alleviate such interactions and the resulting thermal effect. Tests are carried out on a sharp right circular cone with two types of flap configurations in a study of oil flow patterns about the cone at selected angles of attack. Splitting of flaps and moving them to positions away from the symmetry plane did reduce the heating but also reduced the average flap pressure and increased flow complexity.

Hefner, J. N.↗
NASA NTRS1974

Development of a Fowler flap system for a high performance general aviation airfoil

A two-dimensional wind-tunnel evaluation of two Fowler flap configurations on the new GA(W)-1 airfoil was conducted. One configuration used a computer-designed 29-percent chord Fowler flap. The second configuration was modified to have increased Fowler action with a 30-percent chord flap. Force, pressure, and flow-visualization data were obtained at Reynolds numbers of 2.2 million to 2.9 million. Optimum slot geometry and performance were found to be close to computer predictions. A C sub L max of 3.8 was achieved. Optimum flap deflection, slot gap, and flap overlap are presented as functions of C sub L. Tests were made with the lower surface cusp filled in to show the performance penalties that result. Some data on the effects of adding vortex generators and hinged-plate spoilers were obtained.

Wentz, W. H., Jr.↗
NASA NTRS1975

Calculation of static longitudinal aerodynamic characteristics of STOL aircraft with upper surface blown flaps

An existing prediction method developed for EBF aircraft configurations was applied to USB configurations to determine its potential utility in predicting USB aerodynamic characteristics. An existing wing-flap vortex-lattice computer program was modified to handle multiple spanwise flap segments at different flap angles. A potential flow turbofan wake model developed for circular cross-section jets was used to model a rectangular cross-section jet wake by placing a number of circular jets side by side. The calculation procedure was evaluated by comparison of measured and predicted aerodynamic characteristics on a variety of USB configurations. The method is limited to the case where the flow and geometry of the configuration are symmetric about a vertical plane containing the wing root chord. Comparison of predicted and measured lift and pitching moment coefficients were made on swept wings with one and two engines per wing panel, various flap deflection angles, and a range of thrust coefficients. The results indicate satisfactory prediction of lift for flap deflections up to 55 and thrust coefficients less than 2. The applicability of the prediction procedure to USB configurations is evaluated, and specific recommendations for improvements are discussed.

Mendenhall, M. R.↗
NASA NTRS1975

Acoustic characteristics of a large scale wind-tunnel model of a jet flap aircraft

The expanding-duct jet flap (EJF) concept is studied to determine STOL performance in turbofan-powered aircraft. The EJF is used to solve the problem of ducting the required volume of air into the wing by providing an expanding cavity between the upper and lower surfaces of the flap. The results are presented of an investigation of the acoustic characteristics of the EJF concept on a large-scale aircraft model powered by JT15D engines. The noise of the EJF is generated by acoustic dipoles as shown by the sixth power dependence of the noise on jet velocity. These sources result from the interaction of the flow turbulence with flap of internal and external surfaces and the trailing edges. Increasing the trailing edge jet from 70 percent span to 100 percent span increased the noise 2 db for the equivalent nozzle area. Blowing at the knee of the flap rather than the trailing edge reduced the noise 5 to 10 db by displacing the jet from the trailing edge and providing shielding from high-frequency noise. Deflecting the flap and varying the angle of attack modified the directivity of the underwing noise but did not affect the peak noise. A forward speed of 33.5 m/sec (110 ft/sec) reduced the dipole noise less than 1 db.

Falarski, M. D.↗
NASA NTRS1975

Radiated noise from an externally blown flap

The far field noise from subsonic jet impingement on a wing-flap with a 45 deg bend was experimentally investigated. The test parameters are jet Mach number and flap length. For long flaps, the primary source mechanisms are found to be turbulent mixing and flow impingement. For short flaps, the interaction of turbulent flow with the flap trailing edge appears to strongly influence the radiated noise.

Reddy, N. N.↗
NASA NTRS1975

Scrubbing noise of externally blown flaps

An experimental study was conducted to examine the aeroacoustic mechanism that produces externally blown flap (EBF) scrubbing noise, i.e. a surface-radiated noise which is generally strongest normal to UTW deflected flaps. Scrubbing noise was not radiated from portions of the surface adjacent to strong, locally coherent turbulent eddies. Instead, scrubbing noise seemed to come from weak loading fluctuations that were coherent along the scrubbed span. These loading fluctuations probably were induced by the convected large-scale vortex structure of the attached exhaust jet. Deflecting a UTW flap would reduce the distance between the vortex trajectory and the flap surface, increasing the resulting dipole noise and rotating its directivity. In contrast, deflecting a USB flap would increase this distance, so that observable scrubbing noise would be radiated only from the undeflected forward portion of the wing.

Fink, M. R.↗
NASA NTRS1975

Experimental studies of flow separation and stalling on two-dimensional airfoils at low speeds. Phase 2: Studies with Fowler flap extended

Results were given on experimental studies of flow separation and stalling on a two-dimensional GA(W)-1 17 percent thick airfoil with an extended Fowler flap. Experimental velocity profiles obtained from a five tube probe survey with optimum flap gap and overlap setting (flap at 40 deg) are shown at various stations above, below, and behind the airfoil/flap combination for various angles of attack. The typical zones of steady flow, intermittent turbulence, and large scale turbulence were obtained from a hot wire anemometer survey and are depicted graphically for an angle of attack of 12.5 deg. Local skin friction distributions were obtained and are given for various angles of attack. Computer plots of the boundary layer profiles are shown for the case of the flap at 40 deg. Static pressure contours are also given. A GA(W)-2 section model was fabricated with 30 percent Fowler flaps and with pressure tabs.

Seetharam, H. C.↗
NASA NTRS1975

Flow visualization of vortices locked by spanwise blowing over wings featuring a unique leading and trailing-edge flap system

Flow visualization studies were conducted to qualitatively determine the effects of active generation and augmentation of vortex flow over wings by blowing a discrete jet in a spanwise direction in the channel formed by extension of upper surface leading- and trailing-edge flaps. Spanwise blowing from a reflection plane over a rectangular wing was found to generate and lock a dual corotating vortex system within the channel and, at sufficient blowing rates, cause the separated flow off the upper end of the leading-edge flap to reattach to the trailing-edge flap. Test parameters included wing angle of attack, jet momentum coefficient, leading- and trailing-edge flap deflection angle, and jet location above the wing surface. Effects due to removal of the leading- and trailing-edge flap were also investigated.

Erickson, G. E.↗
NASA NTRS1976

Energy management - The delayed flap approach

Flight test evaluation of a Delayed Flap approach procedure intended to provide reductions in noise and fuel consumption is underway using the NASA CV-990 test aircraft. Approach is initiated at a high airspeed (240 kt) and in a drag configuration that allows for low thrust. The aircraft is flown along the conventional ILS glide slope. A Fast/Slow message display signals the pilot when to extend approach flaps, landing gear, and land flaps. Implementation of the procedure in commercial service may require the addition of a DME navigation aid co-located with the ILS glide slope transmitter. The Delayed Flap approach saves 250 lb of fuel over the Reduced Flap approach, with a 95 EPNdB noise contour only 43% as large.

Bull, J. S.↗
NASA NTRS1976

Flight-test measurement of the noise reduction of a jet transport delayed flap approach procedure

A delayed flap approach procedure was flight tested using the NASA CV-990 airplane to measure and analyze the noise produced beneath the flight path. Three other types of landing approaches were also flight tested to provide a comparison of the noise reduction benefits to the delayed flap approach. The conventional type of approach was used as a baseline to compare the effectiveness of the other approaches. The decelerating approach is a variation of the delayed flap approach. A detailed comparison of the ground perceived noise generated during the approaches is presented. For this comparison, the measured noise data were normalized to compensate for variations in aircraft weight and winds that occurred during the flight tests. The data show that the reduced flap approach offers some noise reduction, while the delayed flap and decelerating approaches offer significant noise reductions over the conventional approach.

Foster, J. D.↗
NASA NTRS1977

A flight investigation of the wake turbulence alleviation resulting from a flap configuration change on a B-747 aircraft

A flight test investigation was conducted to evaluate the effects of a flap configuration change on the vortex wake characteristics of a Boeing 747 (B-747) aircraft as measured by differences in upset response resulting from deliberate vortex encounters by a following Learjet aircraft and by direct measurement of the velocities in the wake. The flaps of the B-747 have a predominant effect on the wake. The normal landing flap configuration produces a strong vortex that is attenuated when the outboard flap segments are raised; however, extension of the landing gear at that point increases the vortex induced upsets. These effects are in general agreement with existing wind tunnel and flight data for the modified flap configuration.

Jacobsen, R. A.↗
NASA NTRS1978

A method for calculating externally blown flap noise

Several basic noise components were described. These components are: (1) compact lift dipoles associated with the wing and flaps; (2) trailing edge noise associated with the last trailing edge; and (3) quadrupole noise associated with the undeflected exhaust jet and the free jet located downstream of the trailing edge. These noise components were combined to allow prediction of directivity and spectra for under the wing (UTW) slotted flaps with conventional or mixer nozzles, UTW slotless flaps, upper surface blowing (USB) slotless flaps, and engine in front of the wing slotted flaps. A digital computer program listing was given for this calculation method. Directivities and spectra calculated by this method were compared with free field data for UTW and USB configurations. The UTRC method best predicted the details of the measured noise emission, but the ANOP method best estimated the noise levels directly below these configurations.

Fink, M. R.↗