SEARCH · Search NASA

Results for “flexibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Specifying spacecraft flexible appendage rigidity

As a method for specifying the required degree of rigidity of spacecraft flexible appendages, an analytical technique is proposed for establishing values for the frequency, damping ratio, and modal gain (deflection) of the first several bending modes. The shortcomings of the technique result from the limitations associated with the order of the equations that can be handled practically. An iterative method is prescribed for handling a system whose structural flexibility is described by more than one normal mode. The analytical technique is applied to specifying solar panel rigidity constraints for the NASA Space Telescope. The traditional nonanalytic procedure for specifying the required degree of rigidity of spacecraft flexible appendages has been to set a lower limit below which bending mode frequencies may not lie.

Seltzer, S. M.↗

NASA NTRS1977

Validation of a Flexible Aircraft Take-Off and Landing Analysis (FATOLA)

Modifications to improve the analytical simulation capabilities of a multi-degree-of-freedom flexible aircraft take-off and landing analysis (FATOLA) computer program are discussed. The FATOLA program was used to simulate the landing behavior of a stiff body X-24B reentry research vehicle and of a flexible body supersonic cruise YF-12A research airplane. The analytical results were compared with flight test data, and correlations of vehicle motions, attitudes, forces, and accelerations during the landing impact and rollout were good. For the YF-12A airplane, airframe flexibility was found to be important for nose gear loading. Based upon the correlation study presented, the versatility and validity of the FATOLA program for the study of landing dynamics of aircraft are confirmed.

Carden, H. D.↗

NASA NTRS1978

The dynamics and control of large flexible space structures. Part B: Development of continuum model and computer simulation

The equations of motion of an arbitrary flexible body in orbit were derived. The model includes the effects of gravity with all its higher harmonics. As a specific example, the motion of a long, slender, uniform beam in circular orbit was modelled. The example considers both the inplane and three dimensional motion of the beam in orbit. In the case of planar motion with only flexible vibrations, the pitch motion is not influenced by the elastic motion of the beam. For large values of the square of the ratio of the structural modal frequency to the orbital angular rate the elastic motion was decoupled from the pitch motion. However, for small values of the ratio and small amplitude pitch motion, the elastic motion was governed by a Hill's 3 term equation. Numerical simulation of the equation indicates the possibilities of instability for very low values of the square of the ratio of the modal frequency to the orbit angular rate. Also numerical simulations of the first order nonlinear equations of motion for a long flexible beam in orbit were performed. The effect of varying the initial conditions and the number of modes was demonstrated.

Bainum, P. M.↗

NASA NTRS1978

Residual-flexibility corrections for transient modal rotordynamic models

A modal residual-flexibility approach due to Schwendler and MacNeal (1962) is adapted to account for the 'static' contribution of higher-frequency modes without requiring their integration. It is assumed that each rotor mode acts as a lightly damped second-order system. The additional accuracy provided by residual-flexibility corrections becomes progressively more important as a modal model's actual boundary conditions are forced to deviate from the boundary conditions used to define the rotor's original structural model (stiffness matrix) and its associated eigendata input to the transient modal model. An analysis of the high-pressure-oxygen turbopump of the Space Shuttle main engine shows that the residual-flexibility approach ensures a substantial improvement in accuracy for a relatively moderate increase in computer-time requirements.

Childs, D. W.↗

NASA NTRS1978

Remote manipulator system flexibility analysis program: Mission planning, mission analysis, and software formulation

A computer program is described for calculating the flexibility coefficients as arm design changes are made for the remote manipulator system. The coefficients obtained are required as input for a second program which reduces the number of payload deployment and retrieval system simulation runs required to simulate the various remote manipulator system maneuvers. The second program calculates end effector flexibility and joint flexibility terms for the torque model of each joint for any arbitrary configurations. The listing of both programs is included in the appendix.

Kumar, L.↗

NASA NTRS1979

Flexible stator control on the Galileo spacecraft

Galileo is a dual-spin spacecraft designed to deliver a probe to Jupiter and then orbit the planet. The stator, or despun section, contains four flexible modes below 10 Hz and the despun actuator is separated from the inertial sensors by this flexibility. Control loop separation by bandwidth proved unacceptable due to performance requirements. To obtain the desired performance, a control scheme was devised which consists of three parts. First, flexibility damping and control notch filtering are accomplished by phase locked loop techniques. Second, slewing maneuvers are produced by torque profiles which are nonexcitatory to the structure. Finally, a low bandwidth perturbation controller is supplied to remove spacecraft disturbances.

Kopf, E. H.↗

NASA NTRS1980

Flexible materials technology

A survey of all presently defined or proposed large space systems indicated an ever increasing demand for flexible components and materials, primarily as a result of the widening disparity between the stowage space of launch vehicles and the size of advanced systems. Typical flexible components and material requirements were identified on the basis of recurrence and/or functional commonality. This was followed by the evaluation of candidate materials and the search for material capabilities which promise to satisfy the postulated requirements. Particular attention was placed on thin films, and on the requirements of deployable antennas. The assessment of the performance of specific materials was based primarily on the failure mode, derived from a detailed failure analysis. In view of extensive on going work on thermal and environmental degradation effects, prime emphasis was placed on the assessment of the performance loss by meteoroid damage. Quantitative data were generated for tension members and antenna reflector materials. A methodology was developed for the representation of the overall materials performance as related to systems service life. A number of promising new concepts for flexible materials were identified.

Steurer, W. H.↗

NASA NTRS1979

Controllability and observability for flexible spacecraft

Current interest in extended sensing and actuation for the control of flexible spacecraft has led to the use of modern multivariable control theory and the associated concepts of controllability and observability. This paper shows how to evaluate these properties on a mode-by-mode basis for flexible spacecraft control analysis. Relatively simple criteria are derived which indicate the degree of controllability (observability) of each mode in simple literal terms. These criteria provide physical insight and practical guidance on the type, number, and positioning of sensors and actuators. The results are interpreted for force and torque actuators, and for attitude and deformation measurements. To illustrate these ideas, sample controllability and observability 'surfaces' are presented for the Purdue generic flexible spacecraft model.

Hughes, P. C.↗

NASA NTRS1981

Contextual classification on a CDC Flexible Processor system

A potential hardware organization for the Flexible Processor Array is presented. An algorithm that implements a contextual classifier for remote sensing data analysis is given, along with uniprocessor classification algorithms. The Flexible Processor algorithm is provided, as are simulated timings for contextual classifiers run on the Flexible Processor Array and another system. The timings are analyzed for context neighborhoods of sizes three and nine.

Smith, B. W.↗

NASA NTRS1983

The dynamics and control of large flexible space structures

Large, flexible orbiting systems proposed for possible use in communications, electronic orbital based mail systems, and solar energy collection are discussed. The size and low weight to area ratio of such systems indicate that system flexibility is now the main consideration in the dynamics and control problem. For such large, flexible systems, both orientation and surface shape control will often be required. A conceptual development plan of a system software capability for use in analysis of the dynamics and control of large space structures technology (LSST) systems is discussed. This concept can be subdivided into four different stages: (1) system dynamics; (2) structural dynamics; (3) application of control algorithms; and (4) simulation of environmental disturbances. Modeling the system dynamics of such systems in orbit is the most fundamental component. Solar radiation pressure effects and orbital and gravity gradient effects are discussed.

Bainum, P. M.↗

NASA NTRS1983

Modeling of flexible structures for active control

If a flexible structure has a plane of symmetry, the equations of motion can be split into two uncoupled sets, one for symmetrical motions and one for anti-symmetric motions. If there are m controls, it is often convenient to assign the linear combinations of controls that enter into the m lowest frequency modes and new controls. As an example the feed-support structure of a spacecraft antenna is considered. It is modeled as a tetrahedron made up of flexible bars and connected to the spacecraft by six short flexible legs containing force actuators and displacement sensors. Due to the three-sided symmetry of this structure, both the symmetric and the anti-symmetric equations of motion can be decoupled into two subsystems. The resulting four subsystems are: (1) pitch/fore-aft motions with four degrees of freedom (DOF), two controls, and one output (the fore-aft motion of the feed); (2) vertical motions with three DOF, one control, and one output (the vertical motion of the feed); (3) roll/lateral motions with four DOF, two controls, and one output (the lateral motions of the feed); and (4) yaw motion with one DOF, one control, and no output (the feed does not move during yaw motion).

Bryson, A. E., Jr.↗

NASA NTRS1981

Modeling and control of flexible space structures

The effects of actuator and sensor locations on transfer function zeros are investigated, using uniform bars and beams as generic models of flexible space structures. It is shown how finite element codes may be used directly to calculate transfer function zeros. The impulse response predicted by finite-dimensional models is compared with the exact impulse response predicted by the infinite dimensional models. It is shown that some flexible structures behave as if there were a direct transmission between actuator and sensor (equal numbers of zeros and poles in the transfer function). Finally, natural damping models for a vibrating beam are investigated since natural damping has a strong influence on the appropriate active control logic for a flexible structure.

Wie, B.↗

NASA NTRS1983

The dynamics and control of large flexible space structures, 6

The controls analysis based on a truncated finite element model of the 122m. Hoop/Column Antenna System focuses on an analysis of the controllability as well as the synthesis of control laws. Graph theoretic techniques are employed to consider controllability for different combinations of number and locations of actuators. Control law synthesis is based on an application of the linear regulator theory as well as pole placement techniques. Placement of an actuator on the hoop can result in a noticeable improvement in the transient characteristics. The problem of orientation and shape control of an orbiting flexible beam, previously examined, is now extended to include the influence of solar radiation environmental forces. For extremely flexible thin structures modification of control laws may be required and techniques for accomplishing this are explained. Effects of environmental torques are also included in previously developed models of orbiting flexible thin platforms.

Bainum, P. M.↗

NASA NTRS1984

The design and operational development of self-streamlining 2-dimensional flexible walled test sections

Self streamlining two dimensional flexible walled test sections eliminate the uncertainties found in data from conventional test sections particularly at transonic speeds. The test section sidewalls are rigid, while the floor and ceiling are flexible and are positioned to streamline shapes by a system of jacks, without reference to the model. The walls are therefore self streamlining. Data are taken from the model when the walls are good streamlines such that the inevitable residual wall induced interference is acceptably small and correctable. Successful two dimensional validation testing at low speeds has led to the development of a new transonic flexible walled test section. Tunnel setting times are minimized by the development of a rapid wall setting strategy coupled with on line computer control of wall shapes using motorized jacks. Two dimensional validation testing using symmetric and cambered aerofoils in the Mach number range up to about 0.85 where the walls are just supercritical, shows good agreement with reference data using small height-chord ratios between 1.5 and unity.

Wolf, S. W. D.↗

NASA NTRS1984

A modal reduction method for use with nonlinear simulations of flexible multibody spacecraft

This paper presents a modal truncation method that can be used to prepare the structural flexibility data required as input to flexible, multibody spacecraft simulation programs. The method allows one to truncate the structural models of each flexible body in the system such that the assembled system is free of undesired high frequency system modes. This truncation method enables reasonable simulation costs to be incurred while maintaining dynamic simulation fidelity in the frequency range of interest. A simple one-dimensional example is presented which provides a physical interpretation of the method's workings. In addition, results are presented from the application of the method to a complex spacecraft.

Macala, G. A.↗

NASA NTRS1984

Experimental demonstration of the control of flexible structures

The Large Space Structure Technology Flexible Beam Experiment employs a pinned-free flexible beam to demonstrate such required methods as dynamic and adaptive control, as well as various control law design approaches and hardware requirements. An attempt is made to define the mechanization difficulties that may inhere in flexible structures. Attention is presently given to analytical work performed in support of the test facility's development, the final design's specifications, the control laws' synthesis, and experimental results obtained.

Schaechter, D. B.↗

NASA NTRS1984

Two- and three-dimensional model and wall data from a flexible-walled transonic test section

Both two- and three-dimensional model testing is being carried out in the transonic flexible-walled wind tunnel test section. The test section has flexible top and bottom walls with rigid sidewalls. Interference is eliminated by adjustments based on data taken at walls in two dimensional models. Cast-7 data will illustrate agreement between various flexible-walled tunnels. In three-dimensional models interference cannot be eliminated but wall adjustments can control and relieve the principal sources of wall-induced errors. Estimates of magnitudes of the control which may be exercised on flow by movement of one wall jack are presented. A wall control algorithm (still in analytic development stage) based on use of this data is described. Brief examples of control of wall-induced perturbations in region of model are given.

Goodyer, M. J.↗

NASA NTRS1985

Impact of magnetic isolation on pointing system performance in the presence of structural flexibility

The inertial pointing stability of a gimbal pointing system (AGS) was compared with a magnetic pointing/gimbal followup system (ASPS), under certain conditions of system structural flexibility and disturbance inputs from the gimbal support structure. Separate 3 degree-of-freedom (3DOF) linear models based on NASTRAN modal flexibility data for the gimbal and support structures were generated for the ASPS configurations. Using the models inertial pointing control loops providing 6dB of gain margin and 45 deg of phase margin were defined for each configuration. The pointing loop bandwidth obtained for the ASPS is more than twice the level achieved for the AGS configuration. The AGS limit is attributed to the gimbal and support structure flexibility. As a result of the higher ASPS pointing loop bandwidth and the disturbance rejection provided by the magnetic isolation ASPS pointing performane is significantly better than that of the AGS system. The low frequency peak of the ASPS transfer function from base disturbance to payload angular motion is almost 60dB lower than AGS low frequency peak.

Seller, J.↗