SEARCH · Search NASA

Results for “frequency ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Inference of sea surface temperature, near surface wind, and atmospheric water by Fourier analysis of Scanning Multichannel Microwave Radiometer data

The Scanning Multichannel Microwave Radiometer measures thermal microwave emission from the earth in both polarizations at wavelengths of 0.8, 1.4, 1.7, 2.8 and 4.6 cm. Similar instruments were launched on Nimbus 7 and Seasat. Both spatial resolution on the earth and relative sensitivity to different geophysical parameters change with wavelength. Therefore, spatial Fourier components of geophysical parameters are inferred from the corresponding Fourier components of the radiometer measurements, taking into account the different dependence of signal-to-noise ratio on spatial frequency for each radiometer wavelength. The geophysical parameters are sea surface temperature, near-surface wind speed, integrated water vapor mass, integrated liquid water mass, and the product of rainfall rate with height of the rain layer. The capabilities and limitations of the inversion method are illustrated by means of data from the North Atlantic and from tropical storms.

Rosenkranz, P. W.↗

NASA NTRS1984

Multivariable control of a soft coupled space station

The paper discusses a multivariable controller design for a control configured space station concept. The space station concept is novel in that mechanical filters (soft couplers) are used to reduce structural interaction between adjacent modules. The primary objective of this study is to provide stability augmentation to the soft coupled configuration. The control objective is achieved by a state feedback compensator design. To obtain the desired feedback gains, a modified LQR technique is developed which provides prescribed close-loop frequencies and damping ratios.

Sunkel, J. W.↗

NASA NTRS1983

Galileo probe relay receiver - Acquisition and tracking

The probe-to-orbiter data link for the Jovian mission uses a Manchester encoded BPSK waveform which is demodulated by the Galileo probe relay receiver. Signal acquisition and tracking consists of a sequential probability ratio signal search, frequency acquisition with a least-squares estimator, wide-band phase lock acquisition, and a self-regulating mode control. A discrete Fourier transform serves as the basic mechanism to generate the algorithms that provide this orderly transition to phase tracking. Acquisition and tracking is addressed in this paper with emphasis on key algorithms, rationale, and theoretical/measured performance.

Von Der Embse, U. A.↗

NASA NTRS1985

Contribution of tonal components to the overall loudness, annoyance and noisiness of noise: Relation between single tones and noise spectral shape

A large scale laboratory investigation of loudness, annoyance, and noisiness produced by single-tone-noise complexes was undertaken to establish a broader data base for quanitification and prediction of perceived annoyance of sounds containing tonal components. Loudness, annoyance, and noisiness were distinguished as separate, distinct, attributes of sound. Three different spectral patterns of broadband noise with and without added tones were studied: broadband-flat, low-pass, and high-pass. Judgments were obtained by absolute magnitude estimation supplement by loudness matching. The data were examined and evaluated to determine the potential effects of (1) the overall sound pressure level (SPL) of the noise-tone complex, (2) tone SPL, (3) noise SPL, (4) tone-to-noise ratio, (5) the frequency of the added tone, (6) noise spectral shape, and (7) subjective attribute judged on absolute magnitude of annoyance. Results showed that, in contrast to noisiness, loudness and annoyance growth behavior depends on the relationship between the frequency of the added tone and the spectral shape of the noise. The close correspondence between the frequency of the added tone and the spectral shape of the noise. The close correspondence between loundness and annoyance suggests that, to better understand perceived annoyance of sound mixtures, it is necessary to relate the results to basic auditory mechanisms governing loudness and masking.

Hellman, R. P.↗

NASA NTRS1985

Multivariable control of a soft coupled space station

The paper discusses a multivariate controller design for a control configured space station concept. The space station concept is novel in that mechanical filters (soft couplers) are used to reduce structural interaction between adjacent modules. The primary objective of this study is to provide stability augmentation to the soft coupled configuration. The control objective is achieved by a state feedback compensator design. To obtain the desired feedback gains, a modified LQR technique is developed which provides prescribed close-loop frequencies and damping ratios.

Sunkel, J. W.↗

NASA NTRS1985

Real-time flutter identification

The techniques and a FORTRAN 77 MOdal Parameter IDentification (MOPID) computer program developed for identification of the frequencies and damping ratios of multiple flutter modes in real time are documented. Physically meaningful model parameterization was combined with state of the art recursive identification techniques and applied to the problem of real time flutter mode monitoring. The performance of the algorithm in terms of convergence speed and parameter estimation error is demonstrated for several simulated data cases, and the results of actual flight data analysis from two different vehicles are presented. It is indicated that the algorithm is capable of real time monitoring of aircraft flutter characteristics with a high degree of reliability.

Roy, R.↗

NASA NTRS1986

Acquisition times of carrier tracking sampled data phase-locked loops

Phase acquisition times of type II and III loops typical of the Advanced Receiver are studied by computer simulations when the loops are disturbed by gaussian noise. Reliable estimates are obtained by running 5000 trials for each combination of loop signal-to-noise ratio (SNR) and frequency offset. The probabilities of acquisition are shown versus time from start of acquisition for various loop SNRs and frequency offsets. For frequency offsets smaller than one-fourth of the loop bandwidth and for loop SNRs of 10 dB and higher, the loops acquire with probability 0.99 within 2.5 B sub L for type II loops and within 7/B sub L for type III loops.

Aguirre, S.↗

NASA NTRS1987

Energetics of oscillating lifting surfaces using integral conservation laws

The energetics of oscillating flexible lifting surfaces in two and three dimensions is calculated by the use of integral conservation laws in inviscid incompressible flow for general and harmonic transverse oscillations. Total thrust is calculated from the momentum theorem and energy loss rate due to vortex shedding in the wake from the principle of conservation of mechanical energy. Total power required to maintain the oscillations and hydrodynamic efficiency are also determined. In two dimensions, the results are obtained in closed form. In three dimensions, the distribution of vorticity on the lifting surface is also required as input to the calculations. Thus, unsteady lifting-surface theory must be used as well. The analysis is applicable to oscillating lifting surfaces of arbitrary planform, aspect ratio, and reduced frequency and does not require calculation of the leading-edge thrust.

Ahmadi, Ali R.↗

NASA NTRS1987

Simultaneous structural and control optimization via linear quadratic regulator eigenstructure assignment

A method for simultaneous structural and control design of large flexible space structures (LFSS) to reduce vibration generated by disturbances is presented. Desired natural frequencies and damping ratios for the closed loop system are achieved by using a combination of linear quadratic regulator (LQR) synthesis and numerical optimization techniques. The state and control weighing matrices (Q and R) are expressed in terms of structural parameters such as mass and stiffness. The design parameters are selected by numerical optimization so as to minimize the weight of the structure and to achieve the desired closed-loop eigenvalues. An illustrative example of the design of a two bar truss is presented.

Becus, G. A.↗

NASA NTRS1988

Effects of subpixel image restoration on digital correlation error estimates

The results of initial studies to determine the key parameters influencing the performance of a computer-based measurement system are presented. The system components were modeled, and a representative intensity pattern was chosen and deformed by known amounts. The effect of varying different model parameters in the model was analyzed numerically. The most significant parameters were found to be: (1) the number of quantization levels in the digitization process, (2) the ratio of the frequency of the signal to the frequency of the sampling, and (3) the form of the intensity interpolation function.

Sutton, Michael A.↗

NASA NTRS1989

Transmission-zero bounds for large space structures, with applications

Many large space structure control problems lead quite naturally to the application of an optimal regulator, so the transmission zeros of the open-loop system give fundamental information about the speed of response achievable by the closed-loop system. Despite the importance of this and other well-known zeros properties, little attention has been given to the transmission zeros of large space structures, except for the special case of a rigid spacecraft with flexible appendages. The object of this paper is to remedy this deficiency. In particular, it is proved that the zeros of a structure with colocated sensors and actuators must lie in a region of the complex plane that is defined by its natural frequencies and damping ratios. This generic result, a consequence of the special form of the equations of motion of structural dynamics, admits a very simple graphical interpretation: it is the generalization of the classical pole-zero interlacing property of undamped single-input/single-output structures. The number of sensor/actuator pairs, and their locations, specify where in the permissible region transmission zeros actually lie, thus quantifying the effect of sensor/actuator placement on closed-loop system performance. These points are illustrated by simple examples.

Williams, Trevor↗

NASA NTRS1990

Electromechanical actuation for thrust vector control applications

At present, actuation systems for the Thrust Vector Control (TVC) for launch vehicles are hydraulic systems. The Advanced Launch System (ALS), a joint initiative between NASA and the Air Force, is a launch vehicle that is designed to be cost effective, highly reliable and operationally efficient with a goal of reducing the cost per pound to orbit. As part of this initiative, an electromechanical actuation system is being developed as an attractive alternative to the hydraulic systems used today. NASA-Lewis is developing and demonstrating an Induction Motor Controller Actuation System with a 40 hp peak rating. The controller will integrate 20 kHz resonant link Power Management and Distribution (PMAD) technology and Pulse Population Modulation (PPM) techniques to implement Field Oriented Vector Control (FOVC) of a new advanced induction motor. Through PPM, multiphase variable frequency, variable voltage waveforms can be synthesized from the 20 kHz source. FOVC shows that varying both the voltage and frequency and their ratio (V/F), permits independent control of both torque and speed while operating at maximum efficiency at any point on the torque-speed curve. The driver and the FOVC will be microprocessor controlled. For increased system reliability, a Built-in Test (BITE) capability will be included. This involves introducing testability into the design of a system such that testing is calibrated and exercised during the design, manufacturing, maintenance and prelaunch activities. An actuator will be integrated with the motor controller for performance testing of the EMA TVC system. The design and fabrication of the motor controller is being done by General Dynamics Space Systems Division. The University of Wisconsin-Madison will assist in the design of the advanced induction motor and in the implementation of the FOVC theory. A 75 hp electronically controlled dynamometer will be used to test the motor controller in all four quadrants of operation using flight type control algorithms. Integrated testing of the controller and actuator will be conducted at a facility yet to be named. The EMA system described above is discussed in detail.

Roth, Mary Ellen↗

NASA NTRS1989

Experimental verification of damping mechanisms in a composite beam

A method of estimating the distributed damping parameters based on the measured modal parameters (frequency and damping ratios) was derived. Three different mathematical models were used to model the damping mechanism of a quasi-isotropic pultruded cantilevered beam. These three models were (1) viscous (air) damping, (2) strain rate damping, and (3) both viscous and strain rate damping. The eigenvalues of the partial differential equation model were found to be uninfluenced by any of the three assumed damping models. Values were obtained for each of the damping models as well as the modulus of elasticity of the beam. It was found that the two-parameter damping model provided the best fit to measured modal data. However, the two-parameter damping model could only reproduce the measured damping ratios to within 85 percent.

Cudney, Harley H.↗

NASA NTRS1989

Determining damping mechanisms in a composite beam by experimental modal analysis

A method of estimating the distributed damping parameters of a beam based on measured modal parameters (frequency and damping ratios) is derived. Three different mathematical models were used to model the damping mechanism of a quasi-isotropic pultruded cantilevered beam. These three models were (1) viscous (air) damping, (2) strain-rate damping, and (3) both viscous and strain-rate damping. Values were obtained for each of the damping models as well as the modulus of elasticity of the beam. It is found that the two-parameter damping model provides the best fit to measure modal data. However, the two-parameter damping model can only reproduce the measured damping ratios to within 85 percent.

Cudney, H. H.↗

NASA NTRS1990

Effects of dynamic long-period ocean tides on changes in earth's rotation rate

As a generalization of the zonal response coefficient first introduced by Agnew and Farrell (1978), the zonal response function kappa of the solid earth-ocean system is defined as the ratio, in the frequency domain, of the tidal change in earth's rotation rate to the tide-generating potential. Amplitudes and phases of kappa for the monthly, fortnightly, and nine-day lunar tides are estimated from 2 1/2 years of VLBI UT1 observations, corrected for atmospheric angular momentum effects using NMC wind and pressure series. Using the dynamic ocean tide model of Dickman (1988, 1989), amplitudes and phases of kappa for an elastic earth-ocean system are predicted. The predictions confirm earlier results which found that dynamic effects of the longer-period ocean tides reduce the amplitude of kappa by about 1 percent.

Nam, Young↗

NASA NTRS1990

Effects of stick dynamics on helicopter flying qualities

An experiment that investigated the influence of typical helicopter force-feel system dynamics on roll-axis handling qualities was conducted in concurrent ground and inflight simulations. Variations in lateral control natural frequency and damping ratio, effected by changes in inertia and damping, were evaluated in a disturbance-rejection task. Pilot ratings indicated a preference for low-inertia feel systems, although measured performance was relatively constant over the range of stick characteristics. Force-sensing was compared with position sensing as the input to the control system. Force-sensing improved performance but did not improve pilot ratings. Overall, the results indicated that control-stick dynamics, at least within a reasonable range, did not have a significant effect on pilot-vehicle performance. However, the physical effort required to maintain a desired pilot/manipulator bandwidth became objectionable as the stick inertia increased beyond 5-7 lbm, which was reflected in the pilot ratings and comments.

Watson, Douglas C.↗

NASA NTRS1991

Simulator evaluation of system identification with on-line control law update for the controls and astrophysics experiment in space

A procedure for optimizing the performance of large flexible spacecraft that require active vibration suppression to achieve required performance is presented. The procedure is to conduct on-orbit testing and system identification followed by a control system design. It is applied via simulation to a spacecraft configuration currently being considered for flight test by NASA - the Controls, Astrophysics, and Structures Experiment in Space (CASES). The system simulator is based on a NASTRAN finite element structural model. A finite number of modes is used to represent the structural dynamics. The system simulator also includes models of the electronics, actuators, sensors, the digital controller, and the internal and external disturbances. Nonlinearities caused by quantization are included in the study to examine tolerance of the procedure to modelling errors. Disturbance and sensor noise is modelled as a Gaussian process. For system identification, the system is excited using sinusoidal inputs at the resonant frequencies of the structure using each actuator. Mode shapes, frequencies, and damping ratios are identified from the unforced response sensor data after each excitation. Then, the excitation data is used to identify the actuator influence coefficients. The results of the individual parameter identification analyses are assembled into an aggregate system model. The control design is accomplished based only on the identified model using multi-input/output linear quadratic Gaussian theory. Its performance is evaluated based on time-to-damp as compared with the uncontrolled structure.

Montgomery, Raymond C.↗

NASA NTRS1990

Analytical and experimental study of the vibration of bonded beams with a lap joint

A theoretical model to study the flexural vibration of a bonded lap joint system is described in this paper. First, equations of motion at the joint region are derived using a differential element approach. The transverse displacements of the upper and lower beam are considered to be different. The adhesive is assumed to be linearly viscoelastic and the widely used Kelvin-Voight model is used to represent the viscoelastic behavior of the adhesive. The shear force at the interface between the adhesive and the beam is obtained from the simple bending motion equations of the two beams. The resulting equations of motion are combined with the equations of transverse vibration of the beams in the unjointed regions. These are later solved as a boundary value problem to obtain the eigenvalues and eigenvectors of the system. The model can be used to predict the natural frequencies, modal damping ratios, and mode shapes of the system for free vibration. Good agreement between numerical and experimental results was obtained for a system of graphite epoxy beams lap-jointed by an epoxy adhesive.

Rao, M. D.↗