Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Some effects of grooved runway configurations on aircraft tire braking traction under flooded runway conditions

An experimental investigation was conducted to study the effect of grooved runway configurations on aircraft tire braking traction on flooded runway surfaces. The investigation was performed, utilizing size 49 x 17, type VII, aircraft tires with an inflation pressure of 170 lb per square inch at ground speeds up to approximately 120 knots. The results of this investigation indicate that when the runway is flooded, grooved surfaces provide better braking traction than an ungrooved surface and, in general, the level of braking traction was found to improve as the tire bearing pressure was increased because of an increase in the groove area of either the surface or the tire tread. Rounding the groove edges tended to degrade the tire braking capability from that developed on the same groove configuration with sharp edges. Results also indicate that braking friction coefficients for the test tires and runway surfaces decreased as ground speed was increased because of the hydroplaning effects.

Byrdsong, T. A.↗
NASA NTRS1973

Cornering characteristics of a 40 by 14-16 type 7 aircraft tire and a comparison with characteristics of a C40 by 14-21 cantilever aircraft tire

An investigation was conducted at the Langley aircraft landing loads and traction facility to determine the cornering characteristics of a 40 x 14-16 type VII aircraft tire. These characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained for the tire operating on dry, damp and flooded runway surfaces over a range of yaw angles from 0 deg to 20 deg and at ground speeds from 5 to 100 knots, both with and without braking. The results of this investigation indicated that the cornering capability of the 40 x 14-16 type VII aircraft tire is degraded by high ground speeds, thin-film lubrication and tire hydroplaning effects on the wet surfaces, and brake torque. The cornering capability is greatly diminished when locked-wheel skids are encountered.

Tanner, J. A.↗
NASA NTRS1973

Comparison of predicted and measured low-speed performance of two 51 centimeter-diameter inlets at incidence angle

Theoretical and experimental internal flow characteristics of two 51-cm-diameter inlets are compared. Theoretical flow characteristics along the inlet surface were obtained from an axisymmetric potential flow and boundary layer analysis. The experimental data were obtained from low-speed tests of a high-bypass-ratio turbofan engine simulator. Comparisons between calculated internal surface pressure distributions and experimental data are presented for a free-system velocity of 45 m/sec and for incidence angles from 0 deg to 50 deg. Analysis of boundary layer separation on the inlet lip at incidence angle is the major emphasis of this report. Theoretical boundary layer shape factors, skin friction coefficients, and velocity profiles in the boundary layer are presented, along with the location of the transition region. Theoretical and experimental separation locations are also discussed.

Albers, J. A.↗
NASA NTRS1973

Friction behavior of glass and metals in contact with glass in various environments

Sliding friction experiments have been conducted for heat-resistant glass and metals in contact with glass. These experiments were conducted in various environments including vacuum, moist air, dry air, octane, and stearic acid in hexadecane. Glass exhibited a higher friction force in moist air than it did in vacuum when in sliding contact with itself. The metals, aluminum, iron, and gold, all exhibited the same friction coefficient when sliding on glass in vacuum as glass sliding on glass. Gold-to-glass contacts were extremely sensitive to the environment despite the relative chemical inertness of gold.

Buckley, D. H.↗
NASA NTRS1974

Comparison of theoretical and experimental boundary-layer development in a Mach 2.5 mixed-compression inlet

An analytical investigation was made of the boundary layer flow in an axisymmetric Mach 2.5 mixed compression inlet, and the results were compared with experimental measurements. The inlet tests were conducted in the Lewis 10- by 10-foot supersonic wind tunnel at a unit Reynolds number of 8.2 million/m. The inlet incorporated porous bleed regions for boundary layer control, and the effect of this bleed was taken into account in the analysis. The experimental boundary layer data were analyzed by using similarity laws from which the skin friction coefficient was obtained. The boundary layer analysis included predictions of laminar and turbulent boundary layer growth, transition, and the effects of the shock boundary layer interactions. In addition, the surface static pressures were compared with those obtained from an inviscid characteristics program. The results of investigation showed that the analytical techniques gave satisfactory predictions of the boundary layer flow except in regions that were badly distorted by the terminal shock.

Hingst, W. R.↗
NASA NTRS1974

Effect of strain hardening on friction behavior of iron lubricated with benzyl structures

Sliding friction experiments were conducted with iron, copper, and aluminum in contact with iron in various states of strain. The surfaces were examined in dry sliding and with various benzyl compounds applied as lubricants. Friction experiments were conducted with a hemispherical rider contacting a flat disk at loads of from 50 to 600 grams with a sliding speed of 0.15 cm/min. Results indicate that straining increases friction for dry sliding and for surfaces lubricated with certain benzyl structures such as dibenzyl disulfide. With other benzyl compounds (e.g., benzyl formate), friction coefficients are lower for strained than for annealed iron.

Buckley, D. H.↗
NASA NTRS1974

Computer program for calculation of real gas turbulent boundary layers with variable edge entropy

A user's manual for a computer program which calculates real gas turbulent boundary layers with variable edge entropy on a blunt cone or flat plate at zero angle of attack is presented. An integral method is used. The method includes the effect of real gas in thermodynamic equilibrium and variable edge entropy. A modified Crocco enthalpy velocity relationship is used for the enthalpy profiles and an empirical correlation of the N-power law profile is used for the velocity profile. The skin-friction-coefficient expressions of Spalding and Chi and Van Driest are used in the solution of the momentum equation and in the heat-transfer predictions that use several modified forms of Reynolds analogy.

Boney, L. R.↗
NASA NTRS1973

The use of a digital computer for investigation of the dynamic characteristics of a man while pressing vertically downward with the straight arm on the handle of a vibrator (instrument)

The dynamic characteristics of a man were investigated by the resonance method, by means of recordings of the amplitude-frequency characteristics of a vibrator straight arm human body system on a standard automatic recorder. Experiments were carried out with a specially constructed vibrator, the moving system of which was fastened to a bronze suspension with small losses. Vibrations of the handle, fastened to the moving system, were recorded with an accelerometer. The mass of the moving system m, rigidity of the suspension k and friction coefficient r of the vibrator (calibration) were determined by exact formulas.

Zazhivikhina, A. I.↗
NASA NTRS1974

Experimental investigation of the braking and cornering characteristics of 30 x 11.5-14.5, type 8, aircraft tires with different tread patterns

An investigation was conducted at the aircraft landing loads and traction facility to study the braking and cornering characteristics, including the drag-force and cornering-force friction coefficients, of 30 by 11.5-14.5, type VIII aircraft tires with five different tread patterns. Test data were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg at ground speeds from 5 knots to 100 knots. The results of this investigation indicate that a tread pattern consisting of transverse cuts across the entire width of the tread slightly improved the tire traction performance on wet surfaces. The braking and cornering capability of the tires was degraded by thin-film lubrication and tire hydroplaning effects on the wet runway surfaces. The braking capability of the tires decreased when the yaw angle was increased.

Dreher, R. C.↗
NASA NTRS1974

Viscous reacting flows with wall slip and catalysis applied to spheres in arc jets and flight

The influence of wall slip and catalytic atom-recombination on the flow field and wall heat flux are calculated for high altitude flight and arc jet flow conditions. Boundary equations, which include velocity slip, temperature jump, and wall catalytic atom recombination, are coupled to the viscous reacting multicomponent Navier-Stokes equations. These equations are solved using a time-dependent finite difference technique applied to spheres in an arc jet flow (Reynolds number of 550) and a high altitude flight case representative of the Space Shuttle Orbiter (Reynolds number of 450). The results indicate that catalysis strongly influences the temperature jump, but not the velocity slip. Slip increases the atom fraction and temperature at both the wall and the flow field. Likewise, the shock stand-off distance, the wall heat flux, and friction coefficient are increased over the nonslip cases. The reacting gas calculations confirm the chemically frozen nature of the shock layer in arc jet flows.

Scott, C. D.↗
NASA NTRS1974

Experimental investigation of the cornering characteristics of 18 by 5.5, type 7, aircraft tires with different tread patterns

The characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg and at ground speeds from approximately 5 to 90 knots. The results indicate that a tread pattern with pinholes in the ribs reduces the tire cornering capability at high yaw angles on a damp surface but improves cornering on a dry surface. A tread pattern which has transverse grooves across the entire width of the tread improves the tire cornering performance slightly at high speeds on the flooded runway surface. The cornering capability of all the tires is degraded at high ground speeds by thin film lubrication and/or tire hydroplaning effects. Alterations to the conventional tread pattern provide only marginal improvements in the tire cornering capability which suggests that runway surface treatments may be a more effective way of improving aircraft ground performance during wet operations.

Dreher, R. C.↗
NASA NTRS1975

Wear and friction of oxidation-resistant mechanical carbon graphites at 650 C in air

Studies were conducted to determine the friction and wear properties of experimental carbon-graphites. Hemispherically tipped carbon-graphite rider specimens were tested in sliding contact with rotating Inconel X-750 disks in air. A surface speed of 1.33 m/sec, a load of 500 g, and a specimen temperature of 650 C were used. Results indicate: (1) hardness is not a major factor in determining friction and wear under the conditions of these studies. (2) Friction and wear as low as or lower than those observed for a good commercial seal material were attained with some of the experimental materials studied. (3) The inclusion of boron carbide (as an oxidation inhibitor) has a strong influence on wear rate. (4) Phosphate treatment reduces the friction coefficient when boron carbide is not present in the base material.

Allen, G. P.↗
NASA NTRS1975

Boundary lubrication of formulated C-ethers in air to 300 C

Friction and wear measurements were made in dry and moist air on CVM M-50 steel lubricated with six C-ether formulations containing phosphorus ester and organic acid additives. Results were compared to those obtained with a formulated Type 2 ester and the C-ether base fluid. A ball-on-disk sliding friction apparatus was used. Experimental conditions were a 1-kilogram load, 17 meter-per-minute (100 rpm) surface speed, and a 25 to 300 C disk temperature range. The C-ether base fluid and the C-ether formulations yielded lower wear than the ester under most test conditions. The C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C and similar or lower values from 25 to 150 C.

Jones, W. R., Jr.↗
NASA NTRS1975

Performance of graphite fiber-reinforced polyimide composites in self-aligning plain bearings to 315 C

A 50/50 (weight percent) composite of graphite fibers and polyimide was studied in self-aligning plain bearings oscillating + or - 15 degrees at 1 hz. The friction coefficient was 0.15 + or - 0.05 at 250 C, and 0.05 + or - 0.02 at 315 C. Best results were obtained with a molded composite liner with chopped graphite fibers randomly oriented in the composite. The specific wear rate is given. It was found that the dynamic unit load capacity was higher for a composite bushing (thin liner), than for a composite ball.

Sliney, H. E.↗
NASA NTRS1975

Plasma-sprayed, self-lubricating coatings for use from cryogenic temperatures to 870 deg C (1600 deg F)

A plasma-sprayed coating is described with good lubricating properties over a wide temperature range. The coating, designated NASA LUBE PS101, contains silver, nichrome, calcium fluoride, and an oxidation protective glass. Oscillating tests were conducted of self-aligning, plain cylindrical bearings, in which the bore was lined with 0.025 cm (0.010 in.) thick coatings of PS101; these were conducted at a radial load of 3.5 x 10 to the 7th power N/sq m (5000 psi) in nitrogen gas at -107 C (-160 F), in vacuum at room temperature, and in air from room temperature to 870 C (1600 F). Friction coefficients were less than 0.25 in all cases and wear rates were low. The coating is not brittle, and it has adequate oxidation resistance in air to at least 870 C.

Sliney, H. E.↗
NASA NTRS1975

Boundary lubrication of formulated C-ethers in air to 300 C

Six C-ether formulations (containing organic acid and phosphorus ester additives) were tested in dry (less than 100 ppm H2O) and moist air (relative humidity 50 percent at 25 C) and temperatures from 25 to 300 C, in order to determine the boundary lubricating characteristics and to compare these results to those obtained with a fully formulated Type II ester and the unformulated C-ether base fluid. The apparatus, procedures and detailed results of the test are described. Friction and wear measurements were made on CVM M-50 steel under 1 kg load and 17 meter per minute (100 rpm) surface speed conditions, for a duration of 25 minutes. In general, the C-ether formulations exhibited higher friction coefficients than the ester from 150 to 300 C and similar or lower values from 25 to 150 C, furthermore, in most test conditions the C-ether base fluid and the six C-ether formulations yielded lower wear than the ester. Possible applications in the aerospace industry are mentioned.

Jones, W. R., Jr.↗
NASA NTRS1976

Effect of nature of oxygen interactions on friction of titanium, aluminum, and molybdenum

Friction studies were conducted with a gold pin contacting titanium, aluminum, and molybdenum surfaces after exposure to oxygen with various methods. Oxygen was adsorbed on the surface, it reacted with the surface, and the surface was ion bombarded with oxygen. The presence of oxygen was monitored with Auger spectroscopy. Titanium friction varied with the mode of the metal-oxygen interaction. It was highest with the adsorbed oxygen and least with ion bombardment using oxygen. Aluminum exhibited lower friction values for the reacted and the ion bombarded surfaces than for the surface having the adsorbed layer. With molybdenum the friction coefficients were generally the same despite the nature of the surface treatment with oxygen.

Buckley, D. H.↗
NASA NTRS1976

Traction Characteristics of a 30 by 11.5-14.5, Type 8, Aircraft Tire on Dry, Wet and Flooded Surfaces

A limited test program was conducted to extend and supplement the braking and cornering data on a 30 x 11.5-14.5, type VIII, aircraft tire to refine the tire/runway friction model for use in the development of an aircraft ground performance simulation. Tire traction data were obtained on dry, wet and flooded runway surfaces at ground speeds ranging from 5 to 100 knots and at yaw angles extending up to 12 deg. These friction coefficients are presented as a function of slip characteristics, namely, the maximum and skidding drag coefficients and the maximum cornering coefficients are presented as a function of both ground speed and yaw angle to extend existing data on that tire size. Tire braking and cornering capabilities were shown to be affected by vehicle ground speed, wheel yaw attitude and the extent of surface wetness.

Yager, T. J.↗