Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

A Study of Bubble and Slug Gas-Liquid Flow in a Microgravity Environment

The influence of gravity on the two-phase flow dynamics is obvious.As the gravity level is reduced,there is a new balance between inertial and interfacial forces, altering the behavior of the flow. In bubbly flow,the absence of drift velocity leads to spherical-shaped bubbles with a rectilinear trajectory.Slug flow is a succession of long bubbles and liquid slug carrying a few bubbles. There is no flow reversal in the thin liquid film as the long bubble and liquid slug pass over the film. Although the flow structure seems to be simpler than in normal gravity conditions,the models developed for the prediction of flow behavior in normal gravity and extended to reduced gravity flow are unable to predict the flow behavior correctly.An additional benefit of conducting studies in microgravity flows is that these studies aide the development of understanding for normal gravity flow behavior by removing the effects of buoyancy on the shape of the interface and density driven shear flows between the gas and the liquid phases. The proposal calls to study specifically the following: 1) The dynamics of isolated bubbles in microgravity liquid flows will be analyzed: Both the dynamics of spherical isolated bubbles and their dispersion by turbulence, their interaction with the pipe wall,the behavior of the bubbles in accelerated or decelerated flows,and the dynamics of isolated cylindrical bubbles, their deformation in accelerated/decelerated flows (in converging or diverging channels), and bubble/bubble interaction. Experiments will consist of the use of Particle Image Velocimetry (PIV) and Laser Doppler Velocimeters (LDV) to study single spherical bubble and single and two cylindrical bubble behavior with respect to their influence on the turbulence of the surrounding liquid and on the wall 2) The dynamics of bubbly and slug flow in microgravity will be analyzed especially for the role of the coalescence in the transition from bubbly to slug flow (effect of fluid properties and surfactant), to identify clusters that promote coalescence and transition the void fraction distribution in bubbly and slug flow,to measure the wall friction in bubbly flow. These experiments will consist of multiple bubbles type flows and will utilize hot wire and film anemometers to measure liquid velocity and wall shear stress respectively and double fiber optic probes to measure bubble size and velocity as a function of tube radius and axial location.

McQuillen, J.↗

Collapse of Reacted Fracture Surface Decreases Permeability and Frictional Strength

Abstract Geochemical and geomechanical perturbations of the subsurface caused by the injection of fluids present risks of leakage and seismicity. This study investigated how acidic fluid flow affects hydraulic and frictional properties of fractures using experiments with 3.8‐cm‐long specimens of Eagle Ford shale, a laminated shale with carbonate‐rich strata. In low‐pressure flow cells, one set of samples was exposed to acidic brine and another set was exposed to neutral brine. X‐ray computed tomography and energy‐dispersive X‐ray spectroscopy revealed that samples exposed to acidic brine were calcite‐depleted and had developed a porous altered layer, while the other set showed no evidence of alteration. After reaction, samples were compressed and sheared in a triaxial cell that supplied normal stress and differential pore pressure at prescribed sliding velocities, independently measuring friction and permeability. During the initial compression, the porous altered layer collapsed into fine particles that filled the fracture. This effectively impeded flow and sealed the fracture, resulting in fracture permeability to decrease 1 to 2 orders of magnitude relative to the unaltered fractures. This is a favorable outcome in subsurface applications where the goal is to reduce leakage risks. However, during shear the reacted fracture had lower frictional strength because the fine‐grained particles in the collapsed layer prevented the formation of interlocking microasperities. Therefore, coupled geochemical and geomechanical processes that could favorably seal fractures could also increase the likelihood of induced seismicity. These findings have important implications for geological carbon sequestration, pressurized fluid energy storage, geothermal energy, and other subsurface technologies.

58 GEOSCIENCES↗

Turbulent flow in a channel with transverse rib heat transfer augmentation

Turbulent flow in a 2D channel with repeated rectangular rib roughness was numerically simulated using a low Reynolds number form of the k-epsilon turbulence model. Friction factors and average Stanton numbers were calculated for various pitch to rib height ratios and bulk Reynolds numbers. Comparisons with experiment were generally adequate, with the predictions of friction superior to those for heat transfer. The effect of variable properties for channel flow was investigated, and the results showed a greater effect for friction than for heat transfer. Comparison with experiment yielded no clear conclusions. The turbulence model was also validated for a related problem, that of flow downstream of an abrupt pipe expansion.

Chang, B. H.↗

Effect of the addition of Si into V 2 O 5 coatings: Structure and tribo-mechanical properties

Vanadium oxide (V2O5) is one of the lubricious oxides with the potential to be used as a solid lubricant at elevated temperatures. However, the material itself is not hard wear-resistant, so most of the research has focused on adding V into hard nitride coatings that could lead to the formation of a self-lubricating V(2)O(5)layer when heated. The other possible solution, which has been less studied, is to look for mechanisms to enhance the hardness of the oxide coating. In this research, we investigate the effect of the addition of Si into the V2O5 coatings, aiming to find conditions that lead to enhance hardness and/or reduced wear while keeping the high temperature lubricity of the V2O5 structure. For this, Si modified V2O5 coatings were deposited using a dual magnetron sputtering system. The results showed that small additions of Si (< 2.0 at%) improved the hardness of the V2O5 coatings up to 5 times while keeping the same temperature dependence of the coefficient of friction than V2O5. Dry sliding experiments using the pin-on-disc configuration against silicon nitride balls were performed at 25, 300 and 600 degrees C. Wear factors in the 10(-7) mm(3)/Nm range were obtained, indicating a good wear resistance. Further addition of Si into the V2O5 structure led to a loss of the crystalline ordering and a significant reduction in the hardness.

Hall-Petch↗

Effect of grain dissolution on sloping ground

The static and dynamic stability of natural or constructed slopes can be affected by dissolution or dissolution-like phenomena. Their underlying mechanisms, however, remain unclear. New experimental results and discrete element simulations provide particle-level and macroscale information on the consequences of mineral dissolution on slope behavior. At the microscale, load-carrying grain arches develop around dissolving particles, the porosity increases, and contact force chains evolve to form a honeycomb topology. At the macroscale, while vertical settlements are the prevailing deformation pattern, lateral granular movements that create mass wasting are prominent in sloping ground, even under the quasi-static granular loss. Horizontal grain displacement is maximum at the surface and decreases linearly with the distance from the slope surface to become zero at the bottom boundaries, much like vertical granular displacement along the depth. Sediments with smaller friction angles and steeper slopes experience greater displacement, both vertically and horizontally. Slopes become flatter after dissolution, with the reduction in slope angle directly related to the loss in ground elevation, ΔH/H o . Yet, because of the porous fabric that results from dissolution, vertical shortening is less than the upper bound, estimated from the loss in the solid mass fraction, ΔH/H o ≈SF. Under water-saturated conditions, the post-dissolution fabric may lead to sudden undrained shear and slope slide.

42 ENGINEERING↗

Rheological effects on friction in elastohydrodynamic lubrication

An analytical and experimental investigation is presented of the friction in a rolling and sliding elastohydrodynamic lubricated contact. The rheological behavior of the lubricant is described in terms of two viscoelastic models. These models represent the separate effects of non-Newtonian behavior and the transient response of the fluid. A unified description of the non-Newtonian shear rate dependence of the viscosity is presented as a new hyperbolic liquid model. The transient response of viscosity, following the rapid pressure rise encountered in the contact, is described by a compressional viscoelastic model of the volume response of a liquid to an applied pressure step. The resulting momentum and energy equations are solved by an iterative numerical technique, and a friction coefficient is calculated. The experimental study was performed, with two synthetic paraffinic lubricants, to verify the friction predictions of the analysis. The values of friction coefficient from theory and experiment are in close agreement.

Trachman, E. G.↗

Calculation of turbulent boundary layers with tangential slot injection

Paper describes a numerical calculation scheme for tangential slot injection (wall-wake) flows; application of the scheme over a wide range of flow conditions indicates increased accuracy compared to previous work. Predictions from the numerical code were in good agreement with experiment (velocity profile, skin-friction, and effectiveness data) for low- and high-speed flows. To achieve improved accuracy, modifications in the turbulence modeling, compared to previous research, were necessary for the imbedded shear layer region in the near field and for the wall region near shear layer impingement. Anomalous behavior was noted for far field experimental velocity profiles in low-speed flow when the slot-to-free stream velocity ratio was near one

Cary, A. M., Jr.↗

An experimental and computational investigation of the transport of Reynolds stress in an axisymmetric swirling boundary layer

A coordinated experimental and computational investigation of the transport and interaction of the individual Reynolds stresses within a turbulent axisymmetric swirling boundary layer flowing over a stationary cylinder is described. The cylinder is instrumented with new directional surface fence skin-friction gages developed for the experiment. The longitudinal and transverse mean velocity profiles are measured with a miniature directional pressure probe. These data provided a standard on which to compare computed results employing a variety of turbulence models. The turbulence models tested range from a simple mixing length model, through a two-equation model, on to the Reynolds stress equation models. The full Reynolds stress equation models are tested with various sets of modeling coefficients for the pressure rate-of-strain correlation. It is shown that while even the simplest model shows the general features of the data, agreement with the experimental data is enhanced through the use of the more complex models. For a better prediction of the data, however, further model improvement is still required.

Higuchi, H.↗

Measurement of rolling friction by a damped oscillator

An experimental method for measuring rolling friction is proposed. The method is mechanically simple. It is based on an oscillator in a uniform magnetic field and does not involve any mechanical forces except for the measured friction. The measured pickup voltage is Fourier analyzed and yields the friction spectral response. The proposed experiment is not tailored for a particular case. Instead, various modes of operation, suitable to different experimental conditions, are discussed.

Dayan, M.↗

Implicit LES of Turbulent, Separated Flow: Wall-Mounted Hump Configuration

Direct simulations (ILES) of turbulent, separated flow over the wall-mounted hump configuration is conducted to investigate the physics of separated flows. A chord-based Reynolds number of Re(sub c) = 47,500 is set up, with a turbulent in flow of Re(sub theta) = 1,400 (theta/c = 3%). FDL3DI, a code that solves the compressible Navier-Stokes equations using high- order compact-difference scheme and filter, with the standard recycling/rescaling method of turbulence generation, is used. Two different configurations of the upper-wall are analyzed, and results are compared with both a higher Re(sub c) (= 936,000, Re(sub theta) = 7,200, theta/c = 0.77%) experiment for major flow features, and RANS (k-omega SST) results. A lower Rec allows for DNS-like mesh resolution, and an adequately wide span. Both ILES and RANS show delayed reattachment compared to experiment, and significantly higher skin friction in the forebody of the hump, as expected. The upper-wall shape influences the C(sub p) distribution only. Results from this study are being used to setup higher Rec (lower theta/c) ILES.

Implicit LES↗

Deformation During Friction Stir Welding

Friction Stir Welding (FSW) is a solid state welding process that exhibits characteristics similar to traditional metal cutting processes. The plastic deformation that occurs during friction stir welding is due to the superposition of three flow fields: a primary rotation of a radially symmetric solid plug of metal surrounding the pin tool, a secondary uniform translation, and a tertiary ring vortex flow (smoke rings) surrounding the tool. If the metal sticks to the tool, the plug surface extends down into the metal from the outer edge of the tool shoulder, decreases in diameter like a funnel, and closes up beneath the pin. Since its invention, ten years have gone by and still very little is known about the physics of the friction stir welding process. In this experiment, an H13 steel weld tool (shoulder diameter, 0.797 in; pin diameter, 0.312 in; and pin length, 0.2506 in) was used to weld three 0.255 in thick plates. The deformation behavior during friction stir welding was investigated by metallographically preparing a plan view sections of the weldment and taking Vickers hardness test in the key-hole region.

Henry J. White↗

Measurements of Reynolds analogy for a hypersonic turbulent boundary layer on a nonadiabatic flat plate.

The purpose of the described experiment was to obtain simultaneous measurements of skin friction and heat transfer at hypersonic Mach numbers, especially with conditions of considerable heat transfer. The experiment was conducted in air in the Ames Hypersonic Wind Tunnel, in which cold air was passed through an alumina storage heater system and heated to total temperatures ranging from about 670 to 1170 K. The nozzle was contoured to produce a flow at Mach 7.4. Thin-skin heat-transfer gauges were placed at equal intervals along the centerline of a sharp-edge flat plate, which was used as the model. A skin-friction balance and a boundary-layer pitot-pressure rake were mounted on each side of the centerline at a certain distance from the leading edge.

Keener, E. R.↗

Airfoil large eddy breakup devices for turbulent drag reduction

It was determined from the present LaRC experiments that tandem, airfoil-shaped large eddy breakup (LEBU) devices can reduce local skin friction as much as 30 percent with a recovery region extending more than 100 boundary layer thicknesses downstream. These airfoils experience near laminar skin friction device drag and produce net drag reductions of up to 7 percent. In contrast to the thin plates used in previous experiments, these airfoils are more than 1000 time stiffer and hence have the potential to withstand the real flight environment (dynamic pressure 36 times larger than in low-speed wing tunnels). In addition, the higher Reynolds numbers of the present tests indicate drag reduction performance is at least as good (or better) as at lower Reynolds numbers.

Anders, J. B.↗

Computation of Turbulent Recirculating Flow in Channels, and for Impingement Cooling

Fully elliptic forms of the transport equations have been solved numerically for two flow configurations. The first is turbulent flow in a channel with transverse rectangular ribs, and the second is impingement cooling of a plane surface. Both flows are relevant to proposed designs for active cooling of hypersonic vehicles using supercritical hydrogen as the coolant. Flow downstream of an abrupt pipe expansion and of a backward-facing step were also solved with various near-wall turbulence models as benchmark problems. A simple form of periodicity boundary condition was used for the channel flow with transverse rectangular ribs. The effects of various parameters on heat transfer in channel flow with transverse ribs and in impingement cooling were investigated using the Yap modified Jones and Launder low Reynolds number k-epsilon turbulence model. For the channel flow, predictions were in adequate agreement with experiment for constant property flow, with the results for friction superior to those for heat transfer. For impingement cooling, the agreement with experiment was generally good, but the results suggest that improved modelling of the dissipation rate of turbulence kinetic energy is required in order to obtain improved heat transfer prediction, especially near the stagnation point. The k-epsilon turbulence model was used to predict the mean flow and heat transfer for constant and variable property flows. The effect of variable properties for channel flow was investigated using the same turbulence model, but comparison with experiment yielded no clear conclusions. Also, the wall function method was modified for use in the variable properties flow with a non-adiabatic surface, and an empirical model is suggested to correctly account for the behavior of the viscous sublayer with heating.

Chang, Byong Hoon↗

Experimental and numerical investigations on flashing-induced instabilities in a single channel

During the start-up phase, natural circulation BWRs (NC-BWRs) need to be operated at low pressure conditions. Such conditions favor flashing-induced instabilities due to the large hydrostatic pressure drop induced by the tall chimney. Moreover, in novel NC-BWR designs the steam separation is performed in the steam separators which create large pressure drops at the chimney outlet, which effect on stability has not been investigated yet. In this work, flashing-induced oscillations occurring in a tall, bottom heated channel are numerically investigated by using a simple linear model with three regions and an accurate implementation for estimating the water properties. The model is used to investigate flashing-induced instabilities in a channel for different values of the core inlet friction value. The results are compared with experiments obtained by using the CIRCUS facility at the same conditions, showing a good agreement. In addition, the experiments on flashing-induced instabilities are presented in a novel manner allowing visualizing new details of the phenomenon numerical stability investigations on the effect of the friction distribution are also done. It is found that by increasing the total restriction in the channel the system is destabilized. In addition, the chimney outlet restriction has a stronger destabilizing effect than the core inlet restriction. A stable two-phase region is observed prior to the instabilities in the experiments and the numerical simulations which may help to pressurize the vessel of NC-BWRs and thus reducing the effects of flashing instabilities during start-up. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Optimization of Tensile and Corrosion Properties of Dissimilar Friction Stir Welded AA2024-7075 Joints

In this work, we performed some joining experiments of dissimilar aluminum alloys AA2024-T351 and AA7075-T651 using friction stir welding (FSW) technique with different process parameters (rotational speed, welding speed and plunge depth). Response surface methodology based on a central composite rotatable design was used to establish the mathematical models predicting the tensile properties and corrosion rate of dissimilar FSW joints with some high confidence level. Analysis of variance method was employed to verify the developed models. Besides, the influences of FSW process parameters on tensile and corrosion properties of joints were analyzed. In order to obtain a desirable combination property of the dissimilar FSW joints, the optimum process parameters after experimental verification were proposed as: rotational speed 1495 rev/min, welding speed 187 mm/min and plunge depth 0.03 mm. This verification illustrated that the developed models are appropriate for the modeling and optimization of process.

36 MATERIALS SCIENCE↗

Friction and wear of nickel in sulfuric acid

Experiments were conducted with elemental nickel sliding on aluminum oxide in aerated sulfuric acid in concentrations ranging from very dilute (10 -4 N, i.e., 5 ppm) to very concentrated (96 percent) acid. Load and reciprocating sliding speeds were kept constant. With the most dilute concentration (10 -4 N) no observable corrosion occurred in or outside the wear area. This was used as the base condition to determine the high contribution of corrosion to total wear loss at acid concentrations between 0.5 percent (0.1 N) and 75 percent. Corrosion reached a maximum rate of 100 millimeters per year at 30 percent acid. At the same time, general corrosion outside the wear area was very low, in agreement with published information. It is clear that friction and wear greatly accelerated corrosion in the wear area. At dilute concentrations of 0.001 and 0.01 N, corrosion in the wear area was low, and general corrosion outside was also low, but local outside regions in the direction of the wear motion experienced some enhanced corrosion, apparently due to fluid motion of the acid.

Rengstorff, G. W. P.↗