Search NASA⌕ Search

SEARCH · Search NASA

Results for “gradient plasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Preliminary results from direct-drive cryogenic target implosion experiments on SGIII prototype laser facility

Since ignition target design with layered deuterium and triterium ice had been proposed several decades ago, much effort was devoted to fabricate and implode cryogenic targets. Until recently, direct-drive cryogenic target implosion experiment was carried out on SGIII prototype laser facility. The target consisted of a plastic capsule supported by fill tube. Cryogenic helium gas was used to cool the capsule to a few degrees below the deuterium triple point. The resulting deuterium ice layer was characterized by optical shadowgraph and smoothed by applied temperature gradient. Eight laser beams with total energy of 7 kJ were used to directly drive the implosion. On the path of laser light to the capsule, there were 500 nm sealing film and helium gas of mm length. X-ray pinhole images were analyzed to confirm that the sealing film, and helium gas had little effect on aiming accuracy but caused some loss of laser energy especially when condensation on the sealing film was observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A direct-adjoint approach for material point model calibration with application to plasticity

Here, this paper proposes a new approach for the calibration of material parameters in local elastoplastic constitutive models. The calibration is posed as a constrained optimization problem, where the constitutive model evolution equations for a single material point serve as constraints. The objective function quantifies the mismatch between the stress predicted by the model and corresponding experimental measurements. To improve calibration efficiency, a novel direct-adjoint approach is presented to compute the Hessian of the objective function, which enables the use of second-order optimization algorithms. Automatic differentiation is used for gradient and Hessian computations. Two numerical examples are employed to validate the Hessian matrices and to demonstrate that the Newton–Raphson algorithm consistently outperforms gradient-based algorithms such as L-BFGS-B.

36 MATERIALS SCIENCE↗

Effect of microstructure on the coupled electromagnetic-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates to infrared laser radiation

The coupled electromagnetic (EM)-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates under laser irradiation and high strain rate loads has been investigated for various aggregate sizes and binder volume fractions. The cyclotrimethylenetrinitramine (RDX) crystals are modeled with a dislocation density-based crystalline plasticity formulation and the estane binder is modeled with finite viscoelasticity through a nonlinear finite element approach that couples EM wave propagation with laser heat absorption, thermal conduction, and inelastic deformation. Material property and local behavior mismatch at the crystal-binder interfaces resulted in geometric scattering of the EM wave, electric field and laser heating localization, high stress gradients, dislocation density, and crystalline shear slip accumulation. Viscous sliding in the binder was another energy dissipation mechanism that reduced stresses in aggregates with thicker binder ligaments and larger binder volume fractions. This investigation indicates the complex interactions between EM waves and mechanical behavior, for accurate predictions of laser irradiation of heterogeneous materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An asynchronous parallel high-throughput model calibration framework for crystal plasticity finite element constitutive models

Crystal plasticity finite element model (CPFEM) is a powerful numerical simulation in the integrated computational materials engineering toolboxes that relates microstructures to homogenized materials properties and establishes the structure–property linkages in computational materials science. However, to establish the predictive capability, one needs to calibrate the underlying constitutive model, verify the solution and validate the model prediction against experimental data. Bayesian optimization (BO) has stood out as a gradient-free efficient global optimization algorithm that is capable of calibrating constitutive models for CPFEM. Here in this paper, we apply a recently developed asynchronous parallel constrained BO algorithm to calibrate phenomenological constitutive models for stainless steel 304 L, Tantalum, and Cantor high-entropy alloy.

304L stainless steel↗

A parallel discrete dislocation dynamics/kinetic Monte Carlo method to study non-conservative plastic processes

Non-conservative processes play a fundamental role in plasticity and are behind important macroscopic phenomena such as creep, dynamic strain aging, loop raft formation, etc. In the most general case, vacancy-induced dislocation climb is the operating unit mechanism. While dislocation/vacancy interactions have been modeled in the literature using a variety of methods, the approaches developed rely on continuum descriptions of both the vacancy population and its fluxes. However, there are numerous situations in physics where point defect populations display heterogeneous concentrations and/or non-smooth kinetics. Here, a kinetic Monte Carlo (kMC) approach for modeling vacancy transport in response to arbitrary stress fields is used. Vacancies are treated as point particles and are coupled to the dislocation substructure representing a deformed material via an advection term defined by the local stress gradients. The stress fields and the dislocation substructure are evolved using a discrete dislocation dynamics (DDD) module. To extend the coupled model to the treatment of large systems, we have implemented it in the massively-parallel DDD code ParaDiS. To avoid numerical incompatibilities associated with merging deterministic (DDD) and stochastic (kMC) integration algorithms, we cast the entire elasto-plastic-diffusive problem within a single stochastic framework, taking advantage of a parallel kMC algorithm to evolve the system as a single event-driven process. The large-scale implementation enables the study of the evolution of a variety of dislocation-defect scenarios governed by non-conservative transport kinetics. After carrying out an exhaustive numerical and computational analysis of our parallel algorithm, we show results that emphasize situations where inhomogeneous vacancy dynamics are of relevance, and compare discrete kinetics to continuum solutions for several cases.

36 MATERIALS SCIENCE↗

Materials for a Stirling engine heater head

Work done on the 25-kW advanced Stirling conversion system (ASCS) terrestrial solar program in establishing criteria and selecting materials for the engine heater head and heater tubes is described. Various mechanisms contributing to incompatibility between materials are identified and discussed. Large thermal gradients, coupled with requirements for long life (60,000 h at temperature) and a large number of heatup and cooldown cycles (20,000) drive the design from a structural standpoint. The pressurized cylinder is checked for creep rupture, localized yielding, reverse plasticity, creep and fatigue damage, and creep ratcheting, in addition to the basic requirements for bust and proof pressure. In general, creep rupture and creep and fatigue interaction are the dominant factors in the design. A wide range of materials for the heater head and tubes was evaluated. Factors involved in the assessment were strength and effect on engine efficiency, reliability, and cost. A preliminary selection of Inconel 713LC for the heater head is based on acceptable structural properties but driven mainly by low cost. The criteria for failure, the structural analysis, and the material characteristics with basis for selection are discussed.

Noble, J. E.↗

Influence of real gas effects on ablative Rayleigh-Taylor instability in plastic target

In this research, real gas effects on ablative Rayleigh-Taylor instability are investigated in a plastic target. The real gas effects are included by adopting the quotidian equation of state (QEOS) model. Theoretical solutions for both QEOS and ideal gas EOS are obtained and compared, based on a same set of ablation parameters. It is found that when real gas effects are considered, the density gradient becomes less steep than that of ideal gas assumption, even though this cannot be used directly to draw a stabilization conclusion for the real gas effects. Further analysis shows that when real gas effects are considered, lower {partial_derivative}p/{partial_derivative}T in the dense shell region has the effect of stabilization, whereas the dependence of the internal energy on the density, lower specific heat (at constant volume) in the dense shell region, and higher specific heat in the low-density ablation region contribute to stronger destabilization effects. Overall, when real gas effects are considered, the destabilization effects are dominant for long wavelength perturbations, and the growth rates become much higher than the results of ideal gas assumption. In our specific case, the maximum relative error reaches 18%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Digital and Gradient Refractive Index Planar Optics by Nanoimprinting Mesoporous Silicon

We report the realization of digital and gradient index flat-optics and planar waveguides using the ‘nanoimprinting refractive index’ (NIRI) technique applied to mesoporous silicon. This technique combines the distinct optical and mechanical metamaterial qualities of mesoporous silicon, including its widely tunable effective refractive index and ability to undergo plastic deformation with a near zero Poisson ratio. Nanoimprinting with premastered and reusable stamps containing analog or digital features enables the continuous or discontinuous patterning of refractive index with high contrast Δn ≥ 0.8 and subwavelength resolution. Using NIRI we experimentally demonstrate a wavefront shaping flat microlens array operating in the visible (405–635 nm) and mesoporous silicon and silica waveguides operating near 1310 nm. This study demonstrates the viability of patterning arbitrary refractive index distributions, n(x,y), on the surface of a chip while circumventing the challenges and limitations of top-down lithographic techniques – thus opening a low-cost and scalable approach for the realization of advanced planar optical technologies.

36 MATERIALS SCIENCE↗

[?]Nonlinear Issues in the Aerothermochemistry of Gases and Materials and the Associated Physics and Dynamics of Interfaces

Our research and technology are focused on nonlinear issues in the aerothermochemistry of gases and materials and the associated physics and dynamics of interfaces. Our program is now organized to aggressively support the NASA Aeronautics Enterprise so as to: (a) develop a new generation of environmentally compatible, economic subsonic aircraft; (b) develop the technology base for an economically viable and environmentally compatible high-speed civil transport; (c) develop the technology options for new capabilities in high-performance aircraft; (d) develop hypersonic technologies for air-breathing flight; and (e) develop advanced concepts, understanding of physical phenomena, and theoretical, experimental, and computational tools for advanced aerospace systems. The implications from our research for aeronautical and aerospace technology have been both broad and deep. For example, using advanced computational techniques, we have determined exact solutions for the Schrodinger equation in electron-molecule scattering allowing us to evaluate atmospheric models important to reentry physics. We have also found a new class of exact solutions for the Navier Stokes equations. In experimental fluid dynamics, we have found explicit evidence of turbulence modification of droplet sizes in shock tube flow with condensation. We have developed a new diagnostic tool for the direct estimation of flow velocities at MHz sampling rates in quasi-one dimensional turbulent flow. This procedure suggests an unexpected confirmation of the possibility of 'natural' closure in Reynolds stresses with deep implications for the development of turbulent models. A transient increase is observed in both the spectral energy decay rate and the degree of chaotic complexity at the interface of a shock wave and a turbulent ionized gas. Even though the gas is apparently brought to rest by the shock wave, no evidence is found either of the expected relaminarization. A unique diamond-shaped nozzle has been designed for a detailed investigation of the effect of significant streamwise vorticity on the acoustic and IR characteristics of supersonic jets. Our results provide convincing evidence of the significant effect of vorticity on the far-field noise for the diamond jet as compared to the conventional round jets. We have found that the countercurrent shear layer mixes much more efficiently than conventional coflowing shear layers. We also developed the fluid thrust vectoring procedures which use counter flow to vector a jet. Our materials research has shown that the steep stress gradients at the fiber-matrix interface could be the primary cause of interface cracks after the processing of metallic and intermetallic matrix composites. New techniques have been evolved for: the microcharacterization of materials including microplastic strain and, point by point, the misorientation and plasticity for matrix composites; thermally induced stress measurements and load relaxation; the growth and characterization of metallic matrix composite interfaces; and for the growth of ferrite materials by pulsed laser deposition. The FAMU commitment to the HBCU Research Center also continues to be broad and deep.

Johnson, Joseph A., III↗

Thermomechanical conversion in metals: dislocation plasticity model evaluation of the Taylor-Quinney coefficient

Using a partitioned-energy thermodynamic framework which assigns energy to that of atomic configurational stored energy of cold work and kinetic-vibrational, in this study we derive an important constraint on the Taylor-Quinney coefficient, which quantifies the fraction of plastic work that is converted into heat during plastic deformation. Associated with the two energy contributions are two separate temperatures – the ordinary temperature for the thermal energy and the effective temperature for the configurational energy. We show that the Taylor-Quinney coefficient is a function of the thermodynamically defined effective temperature that measures the atomic configurational disorder in the material. Finite-element analysis of recently published experiments on the aluminum alloy 6016-T4 [1], using the thermodynamic dislocation theory (TDT), shows good agreement between theory and experiment for both stress-strain behavior and temporal evolution of the temperature. The simulations include both conductive and convective thermal energy loss during the experiments, and significant thermal gradients exist within the simulation results. Computed values of the differential Taylor-Quinney coefficient are also presented and suggest a value which differs between materials and increases with increasing strain.

36 MATERIALS SCIENCE↗

Atomistic tensile deformation mechanisms of Fe with gradient nano-grained structure

Large-scale molecular dynamics (MD) simulations have been performed to investigate the tensile properties and the related atomistic deformation mechanisms of the gradient nano-grained (GNG) structure of bcc Fe (gradient grains with d from 25 nm to 105 nm), and comparisons were made with the uniform nano-grained (NG) structure of bcc Fe (grains with d = 25 nm). The grain size gradient in the nano-scale converts the applied uniaxial stress to multi-axial stresses and promotes the dislocation behaviors in the GNG structure, which results in extra hardening and flow strength. Thus, the GNG structure shows slightly higher flow stress at the early plastic deformation stage when compared to the uniform NG structure (even with smaller grain size). In the GNG structure, the dominant deformation mechanisms are closely related to the grain sizes. For grains with d = 25 nm, the deformation mechanisms are dominated by GB migration, grain rotation and grain coalescence although a few dislocations are observed. For grains with d = 54 nm, dislocation nucleation, propagation and formation of dislocation wall near GBs are observed. Moreover, formation of dislocation wall and dislocation pile-up near GBs are observed for grains with d = 105 nm, which is the first observation by MD simulations to our best knowledge. The strain compatibility among different layers with various grain sizes in the GNG structure should promote the dislocation behaviors and the flow stress of the whole structure, and the present results should provide insights to design the microstructures for developing strong-and-ductile metals.

36 MATERIALS SCIENCE↗

Plastic waste upgrade to olefins via mild slurry microwave pyrolysis over solid acids

Chemical upcycling technologies are emerging as the most viable to combat plastic waste accumulation. Among them, catalytic pyrolysis is very promising as it is feedstock agnostic. However, the high energy demand associated with pyrolysis can lead to significant carbon dioxide production. In this work, we demonstrate that coupling microwave heating with suitable solid acid promoters in a slurry reactor coupled with a distillation unit can overcome the energy-related challenge of conventional pyrolysis, by operating at modest temperatures (350–375 °C), enhancing transport, and furnishing high yields of olefins (~88 %) in seconds, with medium-sized olefins (>75 %) composing a significant fraction. Reduced thermal gradients minimize coke formation, further improving the performance. Techno-economic analysis and life cycle assessment indicate the potential of the technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vickers hardness prediction from machine learning methods

Abstract The search for new superhard materials is of great interest for extreme industrial applications. However, the theoretical prediction of hardness is still a challenge for the scientific community, given the difficulty of modeling plastic behavior of solids. Different hardness models have been proposed over the years. Still, they are either too complicated to use, inaccurate when extrapolating to a wide variety of solids or require coding knowledge. In this investigation, we built a successful machine learning model that implements Gradient Boosting Regressor (GBR) to predict hardness and uses the mechanical properties of a solid (bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio) as input variables. The model was trained with an experimental Vickers hardness database of 143 materials, assuring various kinds of compounds. The input properties were calculated from the theoretical elastic tensor. The Materials Project’s database was explored to search for new superhard materials, and our results are in good agreement with the experimental data available. Other alternative models to compute hardness from mechanical properties are also discussed in this work. Our results are available in a free-access easy to use online application to be further used in future studies of new materials at www.hardnesscalculator.com .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of advanced automatic PET segmentation methods using nonspherical thin-wall inserts

Purpose: The use of positron emission tomography (PET) within radiotherapy treatment planning requires the availability of reliable and accurate segmentation tools. PET automatic segmentation (PET-AS) methods have been recommended for the delineation of tumors, but there is still a lack of thorough validation and cross-comparison of such methods using clinically relevant data. In particular, studies validating PET segmentation tools mainly use phantoms with thick plastic walls inserts of simple spherical geometry and have not specifically investigated the effect of the target object geometry on the delineation accuracy. Our work therefore aimed at generating clinically realistic data using nonspherical thin-wall plastic inserts, for the evaluation and comparison of a set of eight promising PET-AS approaches. Methods: Sixteen nonspherical inserts were manufactured with a plastic wall of 0.18 mm and scanned within a custom plastic phantom. These included ellipsoids and toroids derived with different volumes, as well as tubes, pear- and drop-shaped inserts with different aspect ratios. A set of six spheres of volumes ranging from 0.5 to 102 ml was used for a baseline study. A selection of eight PET-AS methods, written in house, was applied to the images obtained. The methods represented promising segmentation approaches such as adaptive iterative thresholding, region-growing, clustering and gradient-based schemes. The delineation accuracy was measured in terms of overlap with the computed tomography reference contour, using the dice similarity coefficient (DSC), and error in dimensions. Results: The delineation accuracy was lower for nonspherical inserts than for spheres of the same volume in 88% cases. Slice-by-slice gradient-based methods, showed particularly lower DSC for tori (DSC < 0.5), caused by a failure to recover the object geometry. The region-growing method reached high levels of accuracy for most inserts (DSC > 0.76 except for tori) but showed the largest errors in the recovery of pears and drops dimensions (higher than 10% and 30% of the true length, respectively). Large errors were visible for one of the gradient-based contouring methods when delineating drop-shaped inserts. Low DSC due to systematic underestimation of the volumes was observed for our fuzzy clustering method when using nonspherical inserts. The adaptive iterative thresholding method produced the highest DSC score on our nonspherical dataset (DSC > 0.83, except for tori) and showed robustness to the insert geometry. Conclusions: This study investigated the accuracy of eight PET-AS methods for the delineation of objects with a range of nonspherical geometries. The authors’ results confirmed the robustness of some segmentation approaches, but also showed the weaknesses of some of the other methods implemented, which were not observed with spherical inserts. This work therefore highlights the importance of using a variety of thin-wall inserts with complex geometries for the validation of PET-AS methods and provided useful information for further development of the methods tested.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Global and local texture development during initial plastic deformation of cold-pilgered Zircaloy-4 tubing

In this work we present a thorough characterization of the texture development during the initial step of a cold pilgering process of a Zircaloy-4 TREX tube, on which the axial cross section is reduced by 80% over a 40cm length with an overall Q-ratio of 2.34, followed by a recrystallization thermal treatment. Texture across a tapered specimen representing this working zone was characterized by neutron diffraction and high energy synchrotron x-ray diffraction at 28 positions (4 locations along its length and 7 locations across its thickness with 0.3 mm spatial resolution), and on the deformed end after the thermal treatment. Results show that the starting material (TREX tube) presents a texture gradient through its wall thickness, with the c poles aligned to the hoop direction at the outer surface (with radial and hoop Kearns factors: f R =0.36, f H = 0.50), and gradually rotating around the axial direction to become a quasi-radial orientation (~35 o out of the radial direction) at the inner surface ( f R =0.43, f H =0.35). The overall texture becomes more radial due to the cold pilgering, but the texture gradient remains during the whole deformation process, being always more radial at the inner surface, ( f R =0.53, f H =0.37 at 80%) than at the outer surface ( f R =0.41, f H =0.50at 80%). The most remarkable changes in texture produced by the rolling process is a 30 o rotation of the grains around their c-axis, producing a marked increase of the <11 2 ¯ 0> // axial fiber texture at expenses of the original <10 1 ¯ 0> // axial fiber texture observed in the TREX tube. The observed changes in texture during deformation were correctly explained by visco-plastic self-consistent (VPSC) modelling. This was achieved after the inclusion of the basal <a> slip system, which plays a central role to explain the 30 o rotation around the c-axis during deformation. The texture evolution was correctly described after the inclusion of a drag effect to grain rotation due to the interaction with neighbouring grains. The through thickness texture differences are greatly reduced by the recrystallization thermal treatment, with similar Kearns factors at the inner surface ( f R =0.50, f H =0.28) and the outer surface ( f R =0.48, f H =0.39). The predominance of the <10 1 ¯ 0> // axial fiber texture is recovered after recrystallization.

36 MATERIALS SCIENCE↗

An integrated computational materials engineering framework to analyze the failure behaviors of carbon fiber reinforced polymer composites for lightweight vehicle applications

A bottom-up multi-scale modeling approach is used to develop an Integrated Computational Materials Engineering (ICME) framework for carbon fiber reinforced polymer (CFRP) composites, which has the potential to reduce development to deployment lead time for structural applications in lightweight vehicles. In this work, we develop and integrate computational models comprising of four size scales to fully describe and characterize three types of CFRP composites. In detail, the properties of the interphase region are determined by an analytical gradient model and molecular dynamics analysis at the nano-scale, which is then incorporated into micro-scale unidirectional (UD) representative volume element (RVE) models to characterize the failure strengths and envelopes of UD CFRP composites. Then, the results are leveraged to propose an elasto-plastic-damage constitutive law for UD composites to study the fiber tows of woven composites as well as the chips of sheet molding compound (SMC) composites. Subsequently, the failure mechanisms and failure strengths of woven and SMC composites are predicted by the meso-scale RVE models. Finally, building upon the models and results from lower scales, we show that a homogenized macro-scale model can capture the mechanical performance of a hat-section-shaped part under four-point bending. Along with the model integration, we will also demonstrate that the computational results are in good agreement with experiments conducted at different scales. The present work illustrates the potential and significance of integrated multi-scale computational modeling tools that can virtually evaluate the performance of CFRP composites and provide design guidance for CFRP composites used in structural applications.

36 MATERIALS SCIENCE↗

Integration of LIBS with Machine Learning for Real-Time Monitoring of Feedstock in H 2 Gasification Applications

This project, funded by the U.S. Department of Energy (DOE) – Office of Fossil Energy under Award Number DE-FE0032177, aimed to assess the feasibility of an integrated Laser-Induced Breakdown Spectroscopy (LIBS) system with advanced machine learning (ML) models for real-time characterization and potential control of hydrogen gasifiers running on waste materials as feedstocks. This was a multidisciplinary effort that encompassed the acquisition and standardized analysis of individual and blended feedstocks—comprising biomass, coal waste, and plastic waste, followed by the development of a dynamic LIBS bench system for material sample analysis and development of predictive ML models. Comprehensive laboratory testing enabled the creation of a robust elemental dataset that served as the foundation for ML model training. Techniques such as Random Forest, Gradient Boosting, Support Vector Regression, and Neural Networks were employed to predict key feedstock properties, including higher heating value (HHV), moisture content, thermal conductivity, and ash composition with high accuracy. The results were validated against experimental data and demonstrated strong potential for real-time application in gasifier control systems. The project concluded with a study on the integration of the LIBS+ML approach for gasifier control and a techno-economic analysis of the implementation of the approach into hydrogen (H 2 ) gasification systems. Dissemination of results was carried out at a DOE meeting. This work establishes a scalable framework for automated, in-line feedstock quality assessment, offering significant implications for process optimization and emissions reduction in hydrogen production.

01 COAL, LIGNITE, AND PEAT↗

Pinning, flux diodes and ratchets for vortices interacting with conformal pinning arrays

A conformal pinning array can be created by conformally transforming a uniform triangular pinning lattice to produce a new structure in which the six-fold ordering of the original lattice is conserved but where there is a spatial gradient in the density of pinning sites. Here we examine several aspects of vortices interacting with conformal pinning arrays and how they can be used to create a flux flow diode effect for driving vortices in different directions across the arrays. Under the application of an ac drive, a pronounced vortex ratchet effect occurs where the vortices flow in the easy direction of the array asymmetry. When the ac drive is applied perpendicular to the asymmetry direction of the array, it is possible to realize a transverse vortex ratchet effect where there is a generation of a dc flow of vortices perpendicular to the ac drive due to the creation of a noise correlation ratchet by the plastic motion of the vortices. We also examine vortex transport in experiments and compare the pinning effectiveness of conformal arrays to uniform triangular pinning arrays. We find that a triangular array generally pins the vortices more effectively at the first matching field and below, while the conformal array is more effective at higher fields where interstitial vortex flow occurs.

Olson Reichhardt, C. J.↗