Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Corrosion test of HTGR graphite with SIC coating - 18671

The application of SiC composite as a corrosion-resistive coating of graphite remains an important task for HTGR. Different methods and technologies have been developed for SiC-coatings of fuel and graphite frames to reduce their chemical corrosion/spraying and sorption capacity with respect to hydrogen. The use of such a coating would lead to some stabilization of the structure of carbon formations and their properties, which are changing in almost all HTGR operational regimes. This paper presents a study of the chemical interaction of the SiC gradient coating of the high-density IG-110 graphite with H{sub 2}O, O{sub 2}, CH{sub 4}, H{sub 2}, at pressures 1 and 100 Pa in a temperature range up to 1400 deg. C. The experiments at 100 Pa were conducted using mass spectrometry registration of time dependencies of partial pressure changes of the gas mixture, keeping the sample at a constant temperature (integral mode). Similar registrations at 1 Pa of moisture were made in differential mode (under continuous pump out) with 10 deg. C/min heating/cooling rate. The experimental results and microstructural study made it possible to get the parameters and peculiarities of the passive and the active corrosions of SiC and draw some conclusions about the level of the reduction of gas interaction with the bulk graphite due to SiC coating (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Microstructural Characteristics of U-Zr Ingot Slug and Atomized Powder for SFR metal Fuel

Rod-type fuel slugs and spherical powder of U- 10wt.%Zr alloy was also fabricated and characterized in microstructure by injection casting, gravity casting and centrifugal atomization process. U grains became finer from ∼30μm in conventionally ingot rod to ∼2μm in atomized powder. Laminar structure became so fine from ∼0.2μm in conventionally cast ingot rod to 0.05∼0.1μm in atomized powder. Metallic fuels such as U-Zr and U-Pu-Zr alloys have been considered as a nuclear fuel for a sodium-cooled fast reactor (SFR), related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980's. Metallic fuel slugs of U-Pu-Zr alloys for SFR have conventionally been fabricated by an injection casting method. U-Pu-Zr alloy melts are injected and cast into quartz tube molds during injection casting. Metallic fuel slugs are collected by fracturing quartz tubes from the molds. Demolded quartz tubes are treated with radioactive wastes. Recently, management of minor actinides (MA) became an important issue because direct disposal of the long-lived MA can be a long-term burden for a tentative repository up to several hundreds of thousand years. The metallic fuel for SFR should be remotely fabricated under a radiation shielded environment such as a hot cell, because it contains highly radioactive MA such as Np, Am and Cm. The addition of MA in the fuel composition introduces new challenges in the manufacturing of a metallic fuel slug. Am has a high vapor pressure under a vacuum atmosphere at above a melting temperature of U-Zr or U-Pu-Zr. Used graphite crucibles and quartz molds cannot be recycled easily because of difficult decontamination of radioactive residues on their surfaces. It is necessary to minimize the vaporization of Am and volume of radioactive wastes. Atomized metallic fuel does not need these quartz molds during fabrication, as uranium alloys are prepared as a particle form. It is possible to reduce the formation of radioactive wastes by applying the fabrication process of a particulate metallic fuel. Metallic fuel having a fine microstructure, which originates from a rapid solidification effect during atomization process, results in a higher FG release rate during irradiation. In the case of applying a new forming method such as vibrocompaction in Zr sheath, the sheath can act as a reliable FCCI (fuel/cladding chemical interaction) barrier and a re-constraint for external elongation. In addition, atomized fuel powder, dispersed in a Na liquid metal having a high thermal conductivity, may have a lower temperature distribution during irradiation. In order to develop an efficient fabrication process of metallic fuel for SFR, U-Zr ingot rods were fabricated in a lab-scale with various casting methods. Rod-type U-Zr fuel slugs were fabricated by gravity casting and injection casting. Spherical powder of U-Zr alloy was also fabricated by centrifugal atomization. And then, the microstructural characteristics were investigated by using electron microscopes and energy-dispersive electron X-ray spectroscopy. Atomized U-10Zr powder generally showed spherical morphology of below 200 μm in particle size. U grains became finer from ∼30 μm in conventionally ingot rod to ∼2 μm in atomized powder. Laminar structure became so fine from ∼0.2 μm in conventionally cast ingot rod to 0.05∼0.1 μm in atomized powder. Atomized particulate metallic fuel for SFR has a fine microstructure, resulting in a higher fission gas release rate during irradiation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Oxidation Performance of Graphite Samples in TGA versus Vertical Furnace

Oxidation influences the working life of nuclear graphite and can impact function during or after air (or steam) ingress accidents. Temperature, gas flow, oxygen content, and dimensional constraints at the microstructural and macrostructural levels can substantially influence the oxidation rate. The nature of these constraints must be considered when attempting to extrapolate performance from experimental results to service applications, but must also be evaluated in order to compare data among disparate experimental systems. This work compares oxidation test performance from a vertical furnace system (functioning as described by ASTM D7542) with tests using a thermogravimetric analyzer (TGA) adapted to operate in an analogous manner.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of radiation damage effects in high-energy neutrino target graphite using low-energy ions

Exposure of graphite targets to high intensity proton beams at neutrino production facilities causes changes in the target material that can result in a shortened operation lifetime. The dominant factors in this process are currently thought to be mechanical in nature resulting primarily from microstructural effects that lead to thermal and structural changes in bulk material properties. As currently planned beam facilities with increased proton energy and intensity begin to come online it will be important to thoroughly understand these processes, and ideally to be able to predict the effects of new beam designs on target properties. Direct analysis of targets exposed to existing high-energy proton beams is complicated by several factors, such as very limited access to proton beam facilities, high associated costs, irradiation times on the order of months, and the resulting radioactivity of irradiated samples that requires special facilities for post-irradiation examination. Much of the existing literature concerning irradiation damage in graphite has been focused on the needs of the nuclear engineering community, however high-energy proton targets operate in a much different environment. In comparison to graphite irradiated in a nuclear reactor, graphite used in proton beam targets receives a higher dose rate, have greater gas production, and experience short irradiation pulses as opposed to continuous irradiation. Low-energy ion irradiation offers a method of inducing similar levels of radiation damage to high-energy protons while avoiding many of the difficulties and limitations associated with high-energy proton beams and the corresponding activated specimen testing. My research described in this thesis focused on investigating how low-energy ion irradiation could be used to induce the same or similar types of microstructural alteration and mechanical property degradation as that seen in high-energy neutrino production target graphites by varying damage le vels and irradiation temperatures prior to post-irradiation characterisation.

43 PARTICLE ACCELERATORS↗

Evaluating Effects of Shear Processing on 2D Crystalline Materials in 3D Metal Matrices: Atomistic Understanding of High Shear Deformation of Copper Graphene Composites

Composites made of copper and graphene demonstrate high strength, lubricity and enhanced electrical and thermal conductivity compared pure copper. However, manufacturing these composites at bulk volumes for industrial applications has been a big challenge. Shear deformation assisted processing is an effective method for manufacturing materials such as copper-graphene composites demonstrating ultra-fine grain structures and compositional homogeneity. Nevertheless, microstructural evolution of the composites and their property development under such conditions is not clearly understood currently. To rectify this gap in literature, high strain shear deformation of copper coated graphene foils was performed using a tribometer pin in this study. Changes in microstructure of the composite as well as the constituent components under shear deformation was correlated to process conditions. A sharp increase in the coefficient of friction attributed to rupture and smearing of graphene layer into copper substrate was observed during the shear processing. The coefficient of friction of the sheared copper/graphene composite was lower than that of pure copper, suggesting that partially worn graphene is effectively lubricious at the macroscale. A multimodal characterization of the processed region further revealed a shear deformation-induced ultrafine two-phase grain-structure consisting of copper and graphitic domains. Shear deformation reduced the copper grain size from around 50 – 100 µm to ~200 nm on an average and ~2 – 5 nm in some locations. The semicrystalline graphene films were observed to fracture into 10 – 50 µm size flakes. Oxygen enrichment was observed in the processed region. Finally, graphitic domain were identified for the first time in the copper matrix and not just at the grain boundaries providing evidence for a metastable composite microstructure as a result of solid phase processing at room temperature.

36 MATERIALS SCIENCE↗

Generation of an amorphous graphite substrate by cumulative deuterium bombardment using molecular dynamics with full nonbonded interactions

A deuterated amorphous carbon target is generated from a fresh graphite layer via hyperthermal irradiation with deuterium ions using molecular dynamics (MD) simulations. We use interatomic potentials that include nonbonded (long-range) interactions for maximum accuracy and simulate cumulative bombardment up to doses of 5.80 x 10{sup 16} ions cm{sup -2} at 1000 K. The graphite target goes through several stages of erosion and swelling, leading to complete amorphization and significant density loss. The calculations show a transition from graphitelike hybridization to a mixture of diamondlike and linear hybridizations with dose. It is concluded that the current sample sizes obtained directly by cumulative irradiation affordable with MD are not sufficiently large to be used for sputtering calculations under steady-state conditions.

36 MATERIALS SCIENCE↗

A Study on Vitrification for LLW Radioactive Wastes - 16235

Ash and ion exchange resin wastes to be vitrified were considered among various radioactive wastes in the Japanese nuclear industry. The appropriate glass composition for the waste is calculated using the computer program. The glass composition is systematically studied using a ternary diagram, considering viscosity, electrical conductivity, and durability. The optimized glass composition based on calculated parameters of vitrification process and the convenience of mixing wastes is selected for crucible experiment. Since differences between calculated values and measured values may occur upon evaluation of glass formulations using glass formulation computer simulation program, the calculated glass formulations should be verified through experiments on a laboratory scale for more meticulous development of glass formulations. For the follow-up development of glass formulations, several glass formulations are planned to be developed. The candidate glasses for treatment of ash and ion exchange resin were melted and fabricated using reagents, respectively. The chemicals were weighed out to produce the desired batch compositions and mixed thoroughly and then put into clay crucibles for melting. Next, the crucibles were introduced into an electric furnace at 1,150 deg. C in the ambient atmosphere and pressure with occasional stirring by a quartz rod. A hold time of 1 hour was introduced to promote homogenization. Finally, the melted material was poured on a graphite plate to be rapidly cooled. The viscosities of all fabricated glasses were in the desired range. After rapid cooling, the micro-structure of the glasses was analyzed using the SEM. They exhibited amorphous structure with good homogeneity. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Comparison of NBG-18, NBG-17, IG-110 and IG-11 oxidation kinetics in air

In this paper, the oxidation rates of several nuclear-grade graphites, NBG-18, NBG-17, IG-110 and IG-11, were measured in air using thermogravimetry. Kinetic parameters and oxidation behavior for each grade were compared by coke type, filler grain size and microstructure. The thickness of the oxidized layer for each grade was determined by layer peeling and direct density measurements. The results for NBG-17 and IG-11 were compared with those available in the literature and our recently reported results for NBG-18 and IG-110 oxidation in air. The finer-grained graphites IG-110 and IG-11 were more oxidized than medium-grained NBG-18 and NBG-17 because of deeper oxidant penetration, higher porosity and higher probability of available active sites. Variation in experimental conditions also had a marked effect on the reported kinetic parameters by several studies. Finally, kinetic parameters such as activation energy and transition temperature were sensitive to air flow rates as well as sample size and geometry.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Superlow friction of titanium/silicon codoped hydrogenated amorphous carbon film in the ambient air

Titanium/silicon codoped hydrogenated carbon film was deposited on the n-Si (100) substrates by reactive magnetron sputtering Ti80Si20 target in a mixture of argon and methane. Microstructure of the film was investigated using x-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, Raman spectroscopy, and attenuated total reflectance Fourier transform infrared spectroscopy. The investigations have revealed that the film has an amorphous structure and consists of high sp{sup 2} hybridized carbon atoms and bonding hydrogen atoms. The mechanical and tribological properties were evaluated using a nanoindentor and a ball-on-disk tribometer, respectively. The film exhibits hardness of 9.6 GPa, high elastic recovery of 73.0% and high H/E ratio of 0.156. Most significant, the superlow friction ({mu}<0.01) and special low wear rate (2.4x10{sup -7} mm{sup 3} N{sup -1} m{sup -1}) was observed in ambient air with 40% relative humidity. Combining the results of scanning electron microscopy and Raman analyses of the worn surface, it is concluded that some mechanisms, e.g., transfer films, friction-induced graphitization, hydrogen-terminated carbon surface, tribochemical reaction, etc., could be together responsible for this superlow friction in the ambient air.

36 MATERIALS SCIENCE↗

Initial examination of fuel compacts and triso particles from the US AGR-2 irradiation test - 18443

Post-irradiation examination was completed on two as-irradiated compacts from the US Advanced Gas Reactor Fuel Development and Qualification Program's second irradiation test. These compacts were selected for examination due to indications that they may have contained particles that released cesium due to a failed or defective SiC layer. The coated particles were recovered from these compacts by electrolytic deconsolidation of the surrounding graphitic matrix in nitric acid. The leach-burn-leach (LBL) process was used to dissolve and analyze exposed metallic elements (actinides and fission products), and each particle was individually surveyed for relative cesium retention with the Irradiated Microsphere Gamma Analyzer (IMGA). Data from IMGA and LBL examinations provided information on fission product release during irradiation and whether any specific particles had below-average retention that could be related to coating layer defects or radiation-induced degradation. A few selected normal-retention particles and six with abnormally-low cesium inventory were analyzed using x-ray tomography to produce three-dimensional images of the internal coating structure. Four of the low-cesium particles had obviously damaged or degraded SiC, and x-ray imaging was able to guide subsequent grinding and polishing to expose the regions of interest for analysis by optical and electron microscopy. Additional particles from each compact were also sectioned and examined to study the overall radiation-induced microstructural changes in the kernel and coating layers. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The induction of a graphite-like phase on diamond films by a Fe-coating/post-annealing process to improve their electron field emission properties

The electron field emission (EFE) process for diamond films was tremendously enhanced by Fe-coating and post-annealing processes. Microstructural analysis indicates that the mechanism for the improvement in the EFE process is the formation of nanographites with good crystallinity that surround the Fe (or Fe{sub 3}C) nanoclusters. Presumably the nanographites were formed via the reaction of Fe clusters with diamond films, viz. by the dissolution of carbons into Fe (or Fe{sub 3}C) clusters and the reprecipitation of carbon species to the surface of the clusters, a process similar to the growth of carbon nanotubes via Fe clusters as catalyst. Not only is a sufficiently high post-annealing temperature (900 deg. C) required but also a highly active reducing atmosphere (NH{sub 3}) is needed to give a proper microstructure for enhancing the EFE process. The best EFE properties are obtained by post-annealing the Fe-coated diamond films at 900 deg. C in an NH{sub 3} environment for 5 min. The EFE behavior of the films can be turned on at E{sub 0} = 1.9 V/{mu}m, attaining a large EFE current density of 315 {mu}A/cm{sup 2} at an applied field of 8.8 V/{mu}m (extrapolation using the Fowler-Nordheim model leads to J{sub e} = 40.7 mA/cm{sup 2} at a 20 V/{mu}m applied field).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synergistic effects of mica and wollastonite fillers on thermal performance of intumescent fire retardant coating

In this study, intumescent fire retardant coatings (IFRC) were developed to investigate the synergistic effects of reinforced mica and wollastonite fillers based IFRC towards heat shielding, char expansion, char composition and char morphology. Ammonium poly-phosphate (APP) was used as acid source, expandable graphite (EG) as carbon source, melamine as blowing agent, boric acid as additive and Hardener H-2310 polyamide amine in bisphenol A epoxy resin BE-188(BPA) was used as curing agent. Bunsen burner fire test was used for thermal performance according to UL-94 for 1 h. Field Emission Scanning Electron Microscopy (FESEM) was used to observe char microstructure. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) were used to analyse char composition. The results showed that addition of clay filler in IFRC enhanced the fire protection performance of intumescent coating. X-Ray Diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) results showed the presence of boron phosphate, silicon phosphate oxide, aluminium borate in the char that improved the thermal performance of intumescent fire retardant coating (IFRC). Resultantly, the presence of these developed compounds enhanced the Integrity of structural steel upto 500°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural analysis of tristructural isotropic particles in high-temperature steam mixed gas atmospheres

High-temperature gas-cooled reactors (HTGRs) use tristructural isotropic (TRISO) particles embedded in a graphitic matrix material to form the integral fuel element. Potential off-normal reactor conditions for HTGRs include steam ingress with temperatures above 1,000 °C. Fuel element exposure to steam can cause the graphitic matrix material to evolve, forming an atmosphere composed of oxidants and oxidation products and potentially exposing the TRISO particles to these conditions. Investigating the oxidation response of TRISO particles exposed to a mixed gas atmosphere will provide insight into the stability under off-normal conditions. In this study, surrogate TRISO particles were exposed to high temperatures (T = 1,200 °C) in flowing steam (3% < pH 2 O < 21%) and CO (pCO < 1%) to determine the oxidation behavior of the SiC layer when exposed to various mixed gas atmospheres. Scanning electron microscopy, x-ray diffraction, and focused ion beam milling was used to determine the impact of CO and steam on the oxidation behavior of the SiC layer. Therefore, the data presented demonstrates how the SiC layer showed strong oxidation resistance due to limited SiO 2 growth and maintained its structural integrity under these off-normal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural Analysis and Transport Properties of Thermally Sprayed Multiple-Layer Ceramic Coatings

In this paper, multilayer, graded ceramic/metal coatings were prepared by an air plasma spray method on Ti-6Al-4V, 4140 steel and graphite substrates. The coatings were designed to provide thermal barriers for diesel engine pistons to operate at higher temperatures with improved thermal efficiency and cleaner emissions. A systematic, progressive variation in the mixture of yttria-stabilized zirconia and bondcoat alloys (NiCoCrAlYHfSi) was designed to provide better thermal expansion match with the substrate and to improve thermal shock resistance and cycle life. Heat transfer through the layers was evaluated by a flash diffusivity technique based on a model of one-dimensional heat flow. The aging effect of the as-sprayed coatings was captured during diffusivity measurements, which included one heating and cooling cycle. The hysteresis of thermal diffusivity due to aging was not observed after 100-h annealing at 800 °C. The measurements of coatings on substrate and freestanding coatings allowed the influence of interface resistance to be evaluated. Finally, the microstructure of the multilayer coating was examined using scanning electron microscope and electron probe microanalysis.

36 MATERIALS SCIENCE↗

On the thermal oxidation of nuclear graphite relevant to high-temperature gas cooled reactors

Thermal oxidation of nuclear graphite components is highly undesirable because it can cause structural and property degradation that negatively affect a reactor's intended operation. In this work, the body of knowledge of nuclear graphite oxidation is highlighted, including when O 2 , H 2 O, and/or CO 2 are the oxidant. Oxidation conditions relevant to high-temperature gas-cooled reactors (i.e., when oxidation could occur either as an acute or chronic phenomenon) are emphasized. Here, the objective is to summarize graphite oxidation data in a practical and accessible way to inform future research and regulatory requirements. Although each grade of nuclear graphite is different, the oxidation mechanism has underlying commonalities. Although oxidation behavior is grade dependent, the general temperature dependence is well described by a sequence of elementary steps which become rate limiting. Because the regime transition temperature depends on sample microstructure, size, and oxidant supply rate, extrapolating results beyond the experimental range should be done cautiously. Gravimetric oxidation rate measurements generally replicate well. However, caution must be exercised when rates are estimated by other methods or for samples that deviate significantly in size. Air oxidation data for IG-110, NBG-18, and PCEA graphite is critically reviewed to emphasize this point. Despite the amount of experimental data, gaps remain. Sample size and shape effects are not fully explained. Data on the oxidant penetration depth are insufficient. Analytical assessments demonstrate that lower temperature oxidation does not necessarily imply that oxidation is uniform throughout the bulk. Oxidation occurs faster at higher temperature but is more localized to the exposed surface. Paradoxically, at equal mass loss percentage, low temperature oxidation leads to greater property degradation than at high temperature. The isolated effect of oxidation is important; however, a gap remains in the systematic understanding of any potential effect of neutron irradiation on graphite structure and reactivity.

36 MATERIALS SCIENCE↗

Structure and tribological properties of steel after non-vacuum electron beam cladding of Ti, Mo and graphite powders

The non-vacuum electron beam cladding technique was used to fabricate layers alloyed with Ti, Mo and C on the surface of low-alloyed steel. Two types of experiments were carried out. In the first experiment, a mixture of Ti and graphite powders was used for cladding; in the second, a mixture of Ti, Mo and graphite powders was used for cladding. CaF{sub 2} powder or a mixture of CaF{sub 2} and LiF powders was used as flux. The thickness of the cladded layers was in the range of 2–2.2 mm. The structure of the layers was studied using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The microhardness after cladding of the layers fabricated by cladding of Ti and graphite powders was 8–9 GPa, while the microhardness of layers with Mo additions reached 11–12 GPa. The highest wear resistance at sliding friction and friction in abrasive environment was reached in the samples fabricated using Ti, Mo and graphite mixture due to the higher hardness and the martensite–austenite structure of the matrix. The wear resistance against fixed abrasive particles was 2.4 times higher compared to that of carburized and quenched steel. - Highlights: • Ti, C and Mo mixture of powders was cladded using non-vacuum electron beam treatment. • The depth of the cladded layers was 2.0 … 2.2 mm. • The microhardness of layer with Mo, Ti and C additions reached ~ 11 … 12 GPa. • The hardening of the layers caused by the formation of TiC particles and martensitic matrix • Wear resistance of cladded coatings was 2.4 higher than carburized steel.

36 MATERIALS SCIENCE↗

Ion irradiation induced structural modifications and increase in elastic modulus of silica based thin films

Ion irradiation is an alternative to heat treatment for transforming organic-inorganic thin films to a ceramic state. One major shortcoming in previous studies of ion-irradiated films is the assumption that constituent phases in ion-irradiated and heat-treated films are identical and that the ion irradiation effect is limited to changes in composition. Here, we investigate the effects of ion irradiation on both the composition and structure of constituent phases and use the results to explain the measured elastic modulus of the films. Our results indicated that the microstructure of the irradiated films consisted of carbon clusters within a silica matrix. It was found that carbon was present in a non-graphitic sp 2 -bonded configuration. It was also observed that ion irradiation caused a decrease in the Si-O-Si bond angle of silica, similar to the effects of applied pressure. A phase transformation from tetrahedrally bonded to octahedrally bonded silica was also observed. The results indicated the incorporation of carbon within the silica network. Finally, a combination of the decrease in Si-O-Si bond angle and an increase in the carbon incorporation within the silica network was found to be responsible for the increase in the elastic modulus of the films.

36 MATERIALS SCIENCE↗

AGC-1 PIE Experimental Plan

Here we report the Post-Irradiation Examination planned for the AGC-1 creep samples. The key data obtained for each grade of graphite included in the AGC-1capsule are dimension, volume, mass and density changes, creep strain, electrical resistivity, Elastic constants (E, G, υ) from sonic velocity, dynamic modulus (from fundamental frequency of vibration), coefficient of thermal expansion, microstructural characterization, and fracture strength. The effect of creep strain on the above properties will be determined. These data are critical to the design of the Next Generation Nuclear Plant. Moreover, the data supports ongoing work in the area of model development, e.g., irradiation effects models such as dimensional change. The data will be used to help underpin the existing American Society of Mechanical Engineers (ASME) design code for graphite core components.

36 MATERIALS SCIENCE↗